AXIOMTEK PANEL6100 User Manual

PANEL6100 & PANEL6100L

10.4” INDUSTRIAL TFT LCD MONITOR

User’s Manual

ii

Disclaimers

The information in this manual has been carefully checked and is believed to be accurate.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or other rights of
third parties, which may result from its use.

Axiomtek assumes no responsibility for any inaccuracies that may be contained in this document.
Axiomtek makes no commitment to update or to keep current the information contained in this
manual.

Axiomtek reserves the right to make improvements to this document and/or product at any time
and without notice.

No part of this document may be reproduced, stored in a retrieval system, or transmitted, in any
form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the
prior written permission of Axiomtek Co., Ltd.

Copyright 2012 by Axiomtek Co. Ltd.,
All rights reserved.
November 2012, Version A2
Printed in Taiwan

iii

Safety Approvals

 CE Marking
 FCC Class A

FCC Compliance

This equipment has been tested and complies with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. If not installed and used in accordance with
proper instructions, this equipment might generate or radiate radio frequency energy and cause
harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measurers:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.

4. Consult the dealer or an experienced radio/TV technician for help.

Shielded interface cables must be used in order to comply with emission limits.

iv

Safety Precautions

Before getting started, read the following important cautions.

1. The P6100&P6100L does not come equipped with an operating system. An operating
system must be loaded first before installing any software into the computer.

2. Be sure to ground yourself to prevent static charge when installing the internal components.
Use a grounding wrist strap and place all electronic components in any static-shielded
devices. Most electronic components are sensitive to static electrical charge.

3. Disconnect the power cord from the P6100&P6100L before making any installation. Be sure
both the system and the external devices are turned OFF. Sudden surge of power could ruin
sensitive components. Make sure the P6100&P6100L is properly grounded.

4. The brightness of the flat panel display decreases with usage. However, hours of use vary
depending on the application environment.

5. Turn OFF the system power before cleaning. Clean the system using a cloth only. Do not
spray any liquid cleaner directly onto the screen. The P6100&P6100L may come with or
without a touchscreen. Although the touchscreen is chemical resistant, it is recommended
that you spray the liquid cleaner on a cloth first before wiping the screen. In case your
system comes without the touchscreen, you must follow the same procedure and not spray
any cleaner on the flat panel directly.

6. Avoid using sharp objects to operate the touchscreen. Scratches on the touchscreen may
cause malfunction or internal failure to the touchscreen.

7. The flat panel display is not susceptible to shock or vibration. When assembling the
P6100&P6100L, make sure it is securely installed.

8. Do not open the system’s back cover. If opening the cover for maintenance is a must, only a
trained technician is allowed to do so. Integrated circuits on computer boards are sensitive
to static electricity. To avoid damaging chips from electrostatic discharge, observe the
following precautions:

 Before handling a board or integrated circuit, touch an unpainted portion of the system

unit chassis for a few seconds. This will help to discharge any static electricity on your
body.

 When handling boards and components, wear a wrist-grounding strap, available from

most electronic component stores.

.

v

Table of Contents

Disclaimers ....................................................................................................................................... ii

FCC Compliance ............................................................................................................................. iii

CHAPTER 1 INTRODUCTION 1

1.1 General Description ............................................................................................................. 1

1.2 Features ............................................................................................................................... 2

1.3 Specifications ....................................................................................................................... 3

1.4 Dimension ............................................................................................................................ 4

1.5 /O Inputs .............................................................................................................................. 5

CHAPTER 2 SYSTEM SETUP 7

2.1 System Configuration .......................................................................................................... 7

2.2 Panel Mounting .................................................................................................................... 8

2.3 Wall Mounting (Option) ...................................................................................................... 10

2.4 Desktop Stand (Option) ..................................................................................................... 11

APPENDIX A SUPPORTED INPUT TIMING MODES 13

Supported Input Timing Modes ....................................................................................................... 13

APPENDIX B OSD OPERATION 15

Function Description of OSD Menu ................................................................................................ 15

vi

MEMO :

P6100&P6100L Series Panel PC User’s Manual

1

CHAPTER 1

INTRODUCTION

This chapter contains the general information and the detailed specifications of the
P6100&P6100L.Chapter1 includes the following sections:

 General Description
 Features
 System Specification
 Dimensions
 I/O Inputs

1.1 General Description

The Panel 6100&6100L, a industrial 10.4 inches view area LCD Monitor comes with slim, light
and reliable features to replace traditional bulky CRT for Industrial application. Its unique front
side design is fit for open frame mounting or panel mounting. The display interface offers VGA-in,
DVI, S-Video (optional), Video(optional) standard interfaces for different input source from PC

system or multimedia system that let you upgrade the display don’t change anything from your

system. Besides, for varied HMI field, you can choose one of resistive or glass interface to meet
your application. In addition, this monitor has more comfort, safety, and environmental protection
for humanized & health consideration those would be the benefit that users can get.

This LCD monitor builds in 10.4” color active matrix thin-film-transistor (TFT) liquid crystal display
to provide superior display performance. A maximum resolution of 800x600 is ideal for displaying
complex graphics and high definition images. Other outstanding designs that enhance this LCD
monitor’s performance are Plug & Play compatibility, and OSD (On Screen Display) controls,
especially OSD, it made you ease adjustment on screen image.

Introduction

P6100&P6100L Series Panel PC User’s Manual

2

Model

IO Ports

P6100

1 x RS-232 or USB for touchscreen
1 x VGA input
1 x DVI
1 x Power input
1 x RCA for video
1 x S-video for video

P6100L

1 x RS-232 or USB for touchscreen
1 x VGA input
1 x DVI
1 x Power input

The differences between P6100 &P6100L is that support different I/O inputs. You can refer to the
below table to check the differences.

1.2 Features

 High contrast color 10.4” SVGA TFT LCD display support resolution up to 800x600
 Heavy-duty steel chassis with NEMA4/IP65-compliant and Aluminum alloy front panel
 Suits with resistive or tempered anti-reflection glass
 Multi-scan function supports SVGA, VGA, VGA-Text, PC-9801, MAC.
 High Brightness and Ultra-wide viewing angle with anti-glare features
 Power management system conforms to VESA DPMS standard
 Advanced OSD control for picture quality adjustment
 Supports VESA ARMS, Desktop Stand
 Rear, Panel, Wall mounting

Introduction

P6100&P6100L Series Panel PC User’s Manual

3

1.3 Specifications

 Construction: Heavy-duty steel chassis
 Brightness: 230 nits
 Control: OSD (On Screen Display) control pad on front side
 Mounting: Support Panel mount, VESA arm mounting, and Wall mount(optional)
 Net weight: 2.6 KGS
 Dimension (main body size):

P6100&P6100L

294.2X231.2X46.6 mm

 Operating Temperature Range: -10oC ~ 55oC
 Relative Humidity: 20% ~ 90%; non-condensing

Introduction

P6100&P6100L Series Panel PC User’s Manual

4

1.4 Dimension

Introduction

5

1.5 /O Inputs

P6100&P6100L Series Panel PC User’s Manual

P6100&6100L Inputs

1. DC +12V or DC+24V: This connector will be connected to the DC 12V Switching Power
Supply.

2. T/S Port (D-sub optional): This connector will be present only if a touchscreen is installed.
It must be connected to the RS-232 port of the PC. The touchscreen cable is included with
all orders, which include the touchscreen option

3. DVI Port: This connector can be connected to the system via the external DVI connector
located on the bottom side of the system unit.

4. VGA Port (D-sub): This D-Sub15 connector can be connected to the system via the
external D-Sub15 connector located on the bottom side of the system unit.

5. Video (optional): This connector can be connected to the system via the external connector
located on the bottom side of system unit.

6. S-Video (optional): This connector can be connected to the system via the external
connector located on the bottom side of system unit.

7. T/S Port (USB optional): This connector will be present only if a touchscreen is installed. It
must be connected to USB port of the PC. The touchscreen cable is included with all orders,
which include the touchscreen option

Introduction

P6100&P6100L Series Panel PC User’s Manual

6

MEMO:

Introduction

P6100&P6100L Series Panel PC User’s Manual

7

CHAPTER 2

SYSTEM SETUP

This chapter details the system parts and components with figures. Sections include

 System Configuration
 Panel Mounting
 Wall Mounting
 Desktop Stand

2.1 System Configuration

The figure below shows the front and back views of P6100&P6100L series.

1. Power switch: Press this button to turn on/off the monitor.

2. Power LED: When the light is green, the power is on, red light when stand by.

3. SEL+:

To scroll up the menu.
To increase the value of selected item.

4. SEL-:

To scroll down the menu.
To decrease the value of selected item.

5. Menu:

Press this button to turn on/off the OSD (On Screen Display) main menu.
Press this button to activate selected items.

6. Exit: Jump out the selection icon.

System Setup

P6100&P6100L Series Panel PC User’s Manual

2.2 Panel Mounting

Two accessory items are needed for this application.
Mounting bracket x 4 pcs
Pan head screws (M4x0.7PxL50.0mm) x 4 pcs

Installation instruction

1. Find a plate and cut off a window, refer the 1.4 P6100&P6100L Dimensions for the
dimension.

2. Screw the mounting bracket to the unit.

3. Combine flange nuts with box head screws and then screw to the mounting bracket to
tighten the unit.

Note: To obtain the maximum degree of moisture resistance, be sure to mount

the P6100&P6100L on a smooth, flat surface.

8 System Setup

P6100&P6100L Series Panel PC User’s Manual

9

Side View

Rear View

35.0

35.0

35.0

35.0

35.0

35.0

35.0

Unit: mm

The panel itself can be from 1.6 to 19.0mm thick.
Strengthening may be required for the panel. Be sure to consider the weight of the

P6100&P6100L when designing the panel.

Note: To enhance the P6100&P6100L’s maintainability, operability and ventilation, allow at

least 35mm clearance between the P6100&P6100L and any other objects. (The
clearance must be large enough to allow you to insert or remove expansion boards
and to attach connectors.)

System Setup

P6100&P6100L Series Panel PC User’s Manual

Bracket

Wall

2.3 Wall Mounting (Option)

The unit is designed to support wall mounting application. It let you to mount the unit on the
wall.

Three accessory items to support this feature.
Wall mounting bracket x 1 pcs
Binding head & washer screws (M4x0.7PxL6.0mm) x 4 pcs
Truss head screws (TTS-4, 3.5x10mm-black) x 4 pcs

Installation instruction

1. Refer the hole location on the page 3 Screw the truss head screws to the hole location on
the wall.

Note: Do not tight the screw for mounting the unit. The minimum space between the wall

and the top of screw is 1.6mm.

2. Mount the wall mounting bracket to the back cover of the unit.

3. Mount the unit to the wall.

10 System Setup

P6100&P6100L Series Panel PC User’s Manual

11

5.00

0

Side View

2.4 Desktop Stand (Option)

The unit is designed to support desktop stand application.
Two accessory items are needed for this application.
Wall mounting bracket x 1 pcs
Binding head & washer screws (M4x0.7PxL6.0mm) x 2 pcs

Installation instruction

Mounting the wall mounting bracket with the binding header & washer screws to the back over of
the unit and then the unit can stand on the desktop.

System Setup

P6100&P6100L Series Panel PC User’s Manual

MEMO:

12 System Setup

13

SUPPORTED INPUT TIMING MODES

SPEC

MODE

Pixel
Freq.

Horizontal Timing

Vertical Timing

Sync
Polar

Freq.

Total

Active

Sync
Polar

Freq.

Total

Active

MHZ

KHz

Pixel

Pixel

Hz

Line

Line

640×480

@60Hz

25.175
VESA

N

31.469

800

640

N

59.940

525

480

640×480

@60Hz

25.175
VESA

N

31.469

800

640

N

59.940

525

480

640×480

@72Hz

31.500
VESA

N

37.861

832

640

N

72.809

520

480

640×480

@75Hz

31.500
VESA

N

37.500

840

640

N

75.000

500

480

800×600

@56Hz

36.000
VESA

P

35.156

1024

800

P

56.250

625

600

800×600

@60Hz 0

40.000
VESA

P

37.879

1056

800

P

60.317

628

600

800×600

@72Hz

50.000
VESA

P

48.077

1040

800

P

72.188

666

600

800×600

@75Hz

49.500
VESA

P

46.875

1056

800

P

75.000

625

600

Supported Input Timing Modes

P6100&P6100L Series Panel PC User’s Manual

APPENDIX A

Note : Timing depends on LCD Panel’s requirement.

Supported Input Timing Modes

P6122 Series Panel PC User’s Manual

14

MEMO:

Supported Input Timing Modes

P6100&P6100L Series Panel PC User’s Manual

15

OSD MENU

Description

General

Adjust the List：

 Brightness of the screen .
 Contrast of the screen .
 Horizontal size of the screen’s image . (for VGA input only)
 Vertical size of the screen’s image . (for VGA input only)
 Horizontal position of the screen’s image. (for VGA input only)
 Vertical position of the screen’s image. (for VGA input only)
 Sharpness of the screen’s image .

Color

9300 , 7500 and 6500 Temperature, user Temperature .

Languages

Multi language support 8 languages（English, French, German, Spanish, Italian,
Japanese, Russian and Chinese） .

Function Description of OSD Menu

※The layout and format of OSD depends on customer’s request.

APPENDIX B

OSD OPERATION

OSD Operation

P6122 Series Panel PC User’s Manual

16

OSD MENU

Description

Tools

Adjust the List：

 OSD Time out .
 OSD position .
 OSD Transparent.
 Recall : “Yes” allows you to recover to the preset mode .
 Auto Adjust…Horizontal position, Vertical position, Horizontal size, Phase of

the screen’s image .

 White balance

Choose Source

Choose Source: (option)

 Analog (VGA)
 Digital (DVI)

OSD Operation