Page 1
PANEL1080-845
All-in-One
8.4” Super Slim
PANEL PC
User’s Manual
Page 2
Disclaimers
The information in this manual has been carefully checked and is believed to be
accurate. AXIOMTEK Co., Ltd. assumes no responsibility for any infringements of
patents or other rights of third parties, which may result from its use.
AXIOMTEK assumes no responsibility for any inaccuracies that may be contained in
this document. AXIOMTEK makes no commitment to update or to keep current the
information contained in this manual.
AXIOMTEK reserves the right to make improvements to this document and/or
product at any time and without notice.
No part of this document may be reproduced, stored in a retrieval system, or
transmitted, in any form or by any means, electronic, mechanical, photocopying,
recording, or otherwise, without the prior written permission of AXIOMTEK Co.,
Ltd.
Copyright 2002 by AXIOMTEK Co., Ltd.
All rights reserved.
August 2002, Version A2
Printed in Taiwan
ii
Page 3
Safety Approvals
! CE Marking
! FCC Class A
FCC Compliance
This equipment has been tested and complies with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. If not installed and used in
accordance with proper instructions, this equipment might generate or
radiate radio frequency energy and cause harmful interference to
radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measurers:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and
receiver.
3. Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV
technician for help.
Shielded interface cables must be used in order to comply with
emission limits.
iii
Page 4
Safety Precautions
Before getting started, read the following impor tant cautions.
1. The PANEL1080-845 does not come equipped with an
operating system. An operating system must be loaded
first before installing any software into the computer.
2. Be sure to ground yourself to prevent static charge when
installing the internal components. Use a grounding wrist
strap and place all electronic components in any
static-shielded devices. Most electronic components are
sensitive to static electrical charge.
3. Disconnect the power cord from the PANEL1080-845
before making any installation. Be sure both the system
and the external devices are turned OFF. Sudden surge
of power could ruin sensitive components. Make sure the
PANEL1080-845 is properly grounded.
4. The brightness of the flat panel display decreases with
usage. However, hours of use vary depending on the
application environment.
5. Turn OFF the system power before cleaning. Clean the
system using a cloth only. Do not spray any liquid cleaner
directly onto the screen. The PANEL1080-845 may come
with or w/o a touchscreen. Although the touchscreen is
chemical resistant, it is recommended that you spray the
liquid cleaner on a cloth first before wiping the screen. In
case your system comes without the touchscreen, you
must follow the same procedure and not spray any
cleaner on the flat panel directly.
6. Avoid using sharp objects to operate the touchscreen.
Scratches on the touchscreen may cause malfunction or
internal failure to the touchscreen.
7. The flat panel display is not susceptible to shock or
vibration. When assembling the PANEL1080-845, make
sure it is securely installed.
iv
Page 5
8. Do not open the system’s back cover. If opening the
cover for maintenance is a must, only a trained
technician is allowed to do so. Integrated circuits on
computer boards are sensitive to static electricity. To
avoid damaging chips from electrostatic discharge,
observe the following precautions:
# Before handling a board or integrated circuit, touch an
unpainted portion of the system unit chassis for a few
seconds. This will help to discharge any static electricity on
your body.
# When handling boards and components, wear a
wrist-grounding strap, available from most electronic
component stores.
Trademarks Acknowledgments
AXIOMTEK is a trademark of AXIOMTEK Co., Ltd.
IBM, PC/AT, PS/2, VGA are trademarks of International
Business Machines Corporation.
Intel and Pentium are trademarks of Intel Corporation.
MS-DOS, Microsoft C and QuickBASIC are trademarks of
Microsoft Corporati on.
C&T is a trademark of Chips and Technologies, Inc.
SST is a trademark of Silicon Storage Technology, Inc.
UMC is a trademark of United Microelectronics
Corporation.
Other brand names and trademarks are the properties of
their respective owners.
v
Page 6
This page does not contain any information.
vi
Page 7
Table of Contents
Chapter 1 Introdu ction------------------------------- 1
1.1 General Description.......................................... 1
1.2 Specifications...................................................2
1.2.1 Core System for PANEL1080-845 SBC84500-based
system ......................................................................2
1.2.2 I/O Syste m ................................................................ 2
1.2.3 Built-i n Peri pher als ................................................... 3
1.2.4 System Spe cifi cation ............................................... 4
1.3 Dimensions.......................................................5
1.4 I/O Outlets ........................................................ 6
1.5 Utilities Supported............................................6
Chapter 2 System Configurat ion ------------------ 7
2.1 System Configuration.......................................7
2.1.1 Front View ................................................................7
2.2 Panel Mount...................................................... 8
Chapter 3 System Installation --------------------- 9
3.1 CompactFlashTM and DRAM Installation.........10
3.2 HDD Installation .............................................11
3.3 3 x Serial Ports ...............................................13
3.4 Parallel Port....................................................13
3.5 VGA ................................................................14
3.6 Ethernet ..........................................................14
3.7 Digital I/Os......................................................15
3.8 Keyboard and PS/2 Mouse Connector ---------- 15
3.9 External FDD ..................................................16
3.10 CompactFlash™ Socket (U25) ........................17
3.11 System O/S and Software Installation ............17
Appendix A Power Suppl y Specifications ---- 19
Appendix B Gener al Care & Maint enance----- 27
Table of Contents
vii
Page 8
This page does not contain any information.
viii
Page 9
PANEL1080-845 8.4” All-in-One PANEL PC User’s Manual
C h a p t e r 1
Introduction
This chapter contains the general information and the detailed
specifications of the PANEL1080-845. Chapter 1 includes the
following sections:
$ General Description
$ System Specification
$ Dimensions
$ I/O Outlets
$ Utilities Supported
1.1 General Description
The PANEL1080-845 super slim industrial PANEL PC is mainly
designed for industrial automation and some space-constricted
embedded applications. For some space-concerned industries, a
traditional PC with a separate main system, display monitor and
keyboard is simply not integrated enough.
Ruggedly designed, the PANEL1080-845 is 100% IBM PC/AT
compatible and it integrates super I/Os, VGA, 8.4” TFT touchscreen,
Ethernet, and packs special industrial features like watchdog timer,
CMOS double backup, all in a single system. The full PC functionality
coupled with its industrial-grade construction easily tailors the system
for any embedded applications and allows the system to endure
continuous operation in any hostile industrial environments where
stability and reliability are a must. Common applications of the
PANEL1080-845 include tooling machine, POI terminal, stand-alone
KIOSK, medical instrument, mobile communication device and
banking system - to name just a few.
Designed by the PC experts for PC professionals, the
PANEL1080-845 is virtually the ultimate one-step solution for your
space-limited applications.
Introduction
1
Page 10
PANEL1080-845 8.4” All-in-One PANEL PC User’s Manual
1.2 Specifications
1.2.1 Core System for PANEL1080-845
SBC84500-based system
$
CPU: 233MHz National Semiconductor Geode Gx1 (other
frequency processors are manufacturer optional)
System Chipset: NX Gx1 + CS5530A
$
BIOS: Award BIOS, Y2K compliant
$
2Mbit Flash ROM, DMI , Plug and Play
System Memory: 1x144-pin SODIMM Max. 128MB SDRAM
$
Real Time Clock: Integration in W83977AF with external
$
Lithium Battery
Watchdog Timer: System reset software programmable
$
timer interval 64 levels, 0.5~8 / 5~80 /
50~800 / 100~1600 seconds
1.2.2 I/O System
$ Standard I/O:
− 4 x serial ports with power;
3 x RS-232, 1 x
RS-232/422/485 jumper
selectable
− 1 x par allel port,
SPP/EPP/ECP
− 1 x External FDD I nterf ace
Digital I/O: Input x 4, Output x 4
$
Ethernet:
$
− Realtek 8139C PCI PnP 10/100Base-T Ethernet
− RJ-45 connector
− 1 x HDD I nterface
− 1 x PS/2 Type (Mini-Din
Connector)
− 1 x Exte rnal IDE I nterf ace
− 1 x USB Ports
2
Introduction
Page 11
PANEL1080-845 8.4” All-in-One PANEL PC User’s Manual
Audio:
$
− AC97 Codec 32bit
− I nternal MIC-in, Line-in and Speaker-out interface
reserved
VGA/Flat Panel Controller:
$
− CS5530A south bridge integrated support CRT/TFT display
via UMA Max. to 4MB sharing memory
− R esol utio n ~Non -in terl aced C RT and TFT moni tor up to
1024 x 768 @ 64K color
$ On-Board SSD:
− CompactFlash socket
$ Extension:
− One 16-bit PC/104 connector
1.2.3 Built-in Peripherals
$ Standard 70W power supply
$ 2.5” hard disk
$ 8.4” anti-glare analog resistive touchscreen with RS-
232 controller sharing COM3
Introduction
3
Page 12
PANEL1080-845 8.4” All-in-One PANEL PC User’s Manual
1.2.4 System Specification
$ 8.4” TFT with 800 x 600 resolution
$ NEMA 4/12 sealed front panel
$ 24X slim type CD-ROM drive (option)
$ External FDD interface
$ Heat dispensing design
$ PC/104 expansion Bus
$ Net weight:
− 3.3 Kgs
$ Dimension (main body size):
− 1080-845:
271 x 212 x 89.9 mm
$ Operating Temperature Range: 0
$ Relative Humidity:
NOTE:
For more detailed information on the system engine
board used in your PANEL PC, refer to the syste m board
User’s Manual that came with the system packaging.
5% ~ 95%; non-condensing
o
C ~ 40oC
4
Introduction
Page 13
PANEL1080-845 8.4” All-in-One PANEL PC User’s Manual
1.3 Dimensions
The following diagrams show the dimensions and outlines of
PANEL1080-845.
75.00
88.40
75.00
182.60
38.40135.2038.40
185.20
Introduction
244.20
81.90
8.00
212.00
271.00
PANEL1080-845 8.4" FLAT PANEL PC DIMENSIONS (Unit:mm)
5
Page 14
PANEL1080-845 8.4” All-in-One PANEL PC User’s Manual
1.4 I/O Outlets
The following figure shows the I/O arrangement of the
PANEL1080-845. The backside of the chassis contains most of the
connectors.
01. Power Switch
02. DIO(4-channel Digital
Inputs/Outputs
03. EXT. IDE
04. COM2
05. COM3/4
06. PRN(Parallel Port)
07. PCMCIA
08. LINE-IN
09. MIC
10. LIN-OUT
11. AC Inlet
12. EXT. FDD
13. COM1
14. USB
15. Keyboard & Mouse
16. LAN(Ethernet Port)
17. VGA
1.5 Utilities Supported
Watchdog Utility
%
Ethernet Utility
%
VGA Drivers
%
Touchscreen Utility
%
6
Introduction
Page 15
PANEL1080-845 8.4” All-in-One PANEL PC User’s Manual
C h a p t e r 2
System Configuration
This chapter details the system parts and components with figures.
Sections include
$ System Major Parts $ Panel Mount
2.1 System Configuration
2.1.1 Front View
The figure below shows the features and controls on the
PANEL1080-845 front panel.
01. Power LED
02. HDD LED
System Configuration
7
Page 16
PANEL1080-845 8.4” All-in-One PANEL PC User’s Manual
2.2 Panel Mount
The PANEL1080-845 is mainly designed for panel mount application.
To mount the PANEL1080-845, the standard set of mounting kit
(included in the system packaging) is needed. Please refer to the
following figure.
8
System Configuration
Page 17
PANEL1080-845 8.4” All-in-One PANEL PC User’s Manual
C h a p t e r 3
System Installation
This chapter describes the installation and the cable connection to the
system connectors. See system board User’s Manual that came with
your PANEL PC packaging for more details. Sections in this chapter
includes
$ CPU
$ DRAM
$ HDD
$ 3 x Serial
Ports
The PANEL1080-845 has a Pentium II little board. It already builds in
a Pentium II CPU, relevant DRAM and a 2.5” HDD. These are all
standard and the system is ready to play. System performance can be
increased by upgrading to, higher capacity DRAM modules and hard
disk drive. The user can use the I/O ports located at the backside of
the chassis to connect external peripheral devices, such as a monitor,
serial devices, parallel printer…etc.
NOTE:
Make sure the power cord is disconnected before any
installation. To install any inte rnal device such as CPU,
DRAM and HDD, take out the rear chassis cover first.
$ Parallel Port
$ VGA
$ Ethernet
$ Digital I/O
$ PS/2 Type
$ System O/S
and
Software
Installation
System Installation
9
Page 18
PANEL1080-845 8.4” All-in-One PANEL PC User’s Manual
3.1 CompactFlashTM and DRAM
Installation
The standard PANEL1080-845 system already builds in a 2.5” hard
disk drive and CompactFlash
TM
card. SBC84500, on the one hand,
provide one 144-pin SODIMM socket that supports system memory
up to 128MB.
When upgrading the HDD or DRAM, or CompactFlash card refer to
the following illustration and instructions:
1. To take off four screws as Fig 2.
2. To open sub-rear cover and put DRAM module or
CompactFlash
TM
module on as Fig 4.
DRAM
Fig 1
Compact Flash
Fig 2
10
Fig 4 Fig 3
System Installation
Page 19
PANEL1080-845 8.4” All-in-One PANEL PC User’s Manual
3.2 HDD Installation
When upgrading the CD-ROM or FDD, refer to the following
illustration and instructions:
1. To take off eight screws as Fig 1.
2. Then opening all rear cover as Fig 2.
3. To take off three screws of HDD drive bay and take out
HDD drive bay.
4. To fix HDD on drive bay by 4 screws.
5. Reverse step 3.
6. Reverse step 1.
Note: If you want to install CD-ROM, the HDD must be set at
Slave mode.
Fig 1 Fig 2
Fig 4 Fig 3
System Installation
11
Page 20
PANEL1080-845 8.4” All-in-One PANEL PC User’s Manual
HDD Bracket
HDD
Fig 5 Fig 6
Fig 7Fig 8
12
Fig 9
System Installation
Page 21
PANEL1080-845 8.4” All-in-One PANEL PC User’s Manual
3.3 3 x Serial Ports
The PANEL1080-845 provides four onboard serial ports installed on
the back bottom side of the chassis. For systems, COM1 and COM4
are RS-232 and COM2 is RS-232/422/485. Each serial port is with
+5V/+12V power capabilities on both Pin 1 and Pin 9, ready to
accommodate a wide array of serial devices, such as fax modem,
scanner, serial mouse and touchscreen...etc. If the touchscreen option
is included, its controller will share COM3.
COM1 and COM4 are all D-SUB 9-pin connectors. To attach to any
serial device, just plug in the device connector to the 9-pin D-SUB. In
terms of transmission distance, the RS-422/485 will perform better
than RS-232. In this case, COM2 is suggested to be set to
RS-422/485 and the related jumpers have to be set correctly first (see
the system board User’s Manual). The RS-422/485 pin assignment is
listed as follows;
12
910
Pin #
1 TX- DATA-
2 No connector No connector
3 TX+ DATA+
4 No connector No connector
5 RX+ No connector
6 No connector No connector
7 RX- No connector
8 No connector No connector
9 GND GND
10 No connector No connector
Signal Name
R2-422 RS-485
3.4 Parallel Port
The printer interface is a 25-pin D-SUB connector. To connect any
parallel device, just plug in the device connector to the 25-pin D-SUB.
System Installation
13
Page 22
PANEL1080-845 8.4” All-in-One PANEL PC User’s Manual
3.5 VGA
The PANEL1080-845 has an analog RGB interface connector. It is
able to connect to an expansion CRT monitor, and the system can
display on both the flat panel and the CRT simultaneously.
3.6 Ethernet
The PANEL1080-845 provides an NE2000 compatible Ethernet
(RJ-45) interface. For network connection, just plug in one cable end
of the PANEL1080-845 100-Base-T Hub into the standard Ethernet
phone jack. The pin assignment of the RJ-45 is listed below;
LAN1 : RJ-45 Connector Pin Assignment
Pin Signal
Tx+ (Data transmission positive)
1
Tx- (Data transmission negative)
2
Rx+(Data reception positive)
3
Rx- (Data reception negative)
6
other
Not use
Green LED, light when 100M link
G
Orange LED,flash when active
O
GO
23
1
RJ-45
456
78
14
System Installation
Page 23
PANEL1080-845 8.4” All-in-One PANEL PC User’s Manual
3.7 Digital I/Os
The PANEL1080-845 provides a digital I/O of 4-channel
inputs/outputs for simple automation control. For example, it can be
used to control the opening and closing of the cash drawer on a POS
system. It can also be used for UPS control. It comes with a 15-pin
D-SUB connector, and its pin position and pin assignment is shown on
the following page.
Digital I/O Pin Assignment
P1 OUT 1 P9 GND
P2 OUT 2 P10 GND
P3 OUT 3 P11 IN1
12345
6
7
8
9
11
12
13
14
15
10
P4 OUT4 P12 IN2
P5 GND P13 IN3
P6 GND P14 IN4
P7 GND P15 GND
P8 GND
3.8 Keyboard and PS/2 Mouse Connector
KBMS1 is a DIN connector for PS/2 keyboard connection.
System Installation
Mouse Clock
VCC
Mouse Data
KBMS1
6
4
2
5
1
Keyboard Clock
3
GND
Keyboard Data
15
Page 24
PANEL1080-845 8.4” All-in-One PANEL PC User’s Manual
3.9 External FDD
The PANEL1080-845 does not build in any floppy disk drive into the
main system. Rather, it provides a FDD interface. An external FDD
cable is provided to connect a standard 3.5” FDD to the system for
system O/S and application software installation. The pin positions
and pin assignments are listed below.
NOTE:
26
25
24
23
22
21
20
19
18
17
16
15
14
An optional external FDD is available for the
PANEL1080-845 system. Consult your au thorized dealers or
sales representatives for more information.
Centronic
External FDD Pin Assignment
13
12
11
10
9
8
7
6
5
4
3
2
1
P 1 SIDE1- P 14 WPT-
P 2 RDATA- P 15 TRK0-
P 3 GND P 16 GND
P 4 GND P 17 WGATE-
P 5 GND P 18 GND
P 6 WDATA- P 19 NC
P 7 REDWC- P 20 STEP-
P 8 NC P 21 DIR-
P 9 NC P 22 MOTE0-
P 10 DRVS0- P 23 NC
P 11 VCC +5V P 24 DSKCHG-
P 12 VCC P 25 NC
P 13 INDEX- P 26 VCC
16
System Installation
Page 25
PANEL1080-845 8.4” All-in-One PANEL PC User’s Manual
3.10 CompactFlash™ Socket (U25)
The PANEL1080 Series is equipped with a CompactFlash disk socket
on the solder side and it supports the IDE interface CompactFlash
disk card. The socket itself is especially designed to prevent any
incorrect installation of the CompactFlash disk card.
When installing or removing the CompactFlash disk card, please
make sure that the system power is off.
The CompactFlash disk card is defaulted as the C: or D: disk drive in
your PC system.
3.11 System O/S and Software Installation
The PANEL1080-845 is not equipped with any operating system. It
builds in a 2.5” HDD and 1.5MB Solid State Disk as memory storage
device. As both devices are built in the system chassis, to load any
O/S or application software into the computer, an external device is
needed to act as a bridge. There are three major ways to load
software into the system.
1. Use the internal 2.5” FDD
2. Use Ethernet: If the Ethernet bootrom is already included in
the system, the user can boot up the system via bootrom
and download system O/S or application software from
the net.
3. Use Internal 24X CD-ROM/HDD
System Installation
17
Page 26
PANEL1080-845 8.4” All-in-One PANEL PC User’s Manual
This Page does not contain any information.
18
System Installation
Page 27
PANEL1080-845 8.4” All-in-One PANEL PC User’s Manual
A p p e n d i x A
Power Supply Specifications
Standard AC Power Supplies
PANEL1080-845 Power Supply
The power supply used in the PANEL1080-845 is a 65W or 70W open
frame power supply. The specifications and features of this special
power supply are listed in the following sections.
Specifications
Specifications
SpecificationsSpecifications
$ High efficiency 65W (or 70W) output
$ Universal input 90 to 264 VAC
$ Overvoltage protection
$ Small size 3” X 5” footprint
$ Continuous short circuit protection
$ Conductive EMI meets FCC/VDE class B
Output Specifications
Voltage Accuracy :
$
+5VDC primary output: + 5%
%
Aux il ia r y ou t p u t : + 5%
%
Total output power:
$
Convection cooled: 55W
%
Forced air cooling: 65W @ 20CFM, 70W @ 20CFM
%
Hold-up time: 16ms typ.
$
$ Overvoltage protecti on: 5 VDC output only
$ Overload protection: 120~200% of rated value
Short circu it protecti on: Co ntinuou s
$
$ Ri pple and noise: 1% pk~pk max.
Input Specifications
$ I nput voltage range: 90~264 VDC
Inrush current: 40A max. (cold start)
$
Input frequency: 47~63 Hz
$
$ Li ne regulation: + 0.5%
Power Supply Specifications
19
Page 28
PANEL1080-845 8.4” All-in-One PANEL PC User’s Manual
General Specifications
$ Efficiency: 75% typ.
Environmental Specifications
$ Operating temperature range 0°C to 70°C
Derating, 50 °C to 70 °C: 2% per °C
$
$ Temperature coefficient: +0.02% per °C
$ Storage temperature range: -40°C to +85°C
$ Humidity, non-condensing: 0°C to 95°C RH
$ Cooling: Free-air convection
$ EMI filter :
Conducted: meets FCC/VDE class B
%
International Standards
Safety Standards
Safety Standards
Safety StandardsSafety Standards
$ Desi gned to meet the following standards:
UL 1950, CSA 22.2 NO. 234, VDE EN 60 950
EMI Standards
EMI Standards
EMI StandardsEMI Standards
$ Desi gned to meet the following limits:
FCC docket 20780 curve “B”, EN55022 “B”
CE Standards
CE Standards
CE StandardsCE Standards
$ Desi gned to meet the following standards:
IEC-801-2 Level 3 8KV air discharge
IEC-801-3 Level 3 3V/M
IEC-801-4 Level 3 2KV
IEC-801-5 Level 3 2KV
20
Power Supply Specifications
Page 29
PANEL1080-845 8.4” All-in-One PANEL PC User’s Manual
Optional DC Power Supplies
(I) +12V DC Power Supply
Input Specifications
Input Specifications
Input SpecificationsInput Specifications
$ I nput voltage range: +9V
$ I nput current: 10A at +12V
Output Specifications
Output Specifications
Output SpecificationsOutput Specifications
$ Load Range:
to +18VDC
DC
max.
DC
Output
+5V 0A 10A 4.95V to 5.05V
+12V 0A 1.5A (open) 11.4V to12.6V
-12V 0A 0.3A -11.4V to –12.6V
− The output range of +12V, -12V and down with +5V
setting. At factory, all outputs in 60 % rated load
conditions, the +5V output is set to between 4.95V and
5.05V, and the other outputs are checked to be within
the specified voltage accuracy range.
Min. Load
Rated Load
Voltage Accuracy
$ Ripple and Noise:
− The peak-to-peak ripple and noise for +5V output is less
than 50mV and less than 100mV for +/-12V outputs, both
at rated loads. Measuring is don e by 15MHz bandwidth
limited oscillosc ope and terminated e ach output with
0.47uF capacitor.
Line Regulation:
$
− The line regulation for +5V output is less than +/-1%, for
12V is less than +/-2%, for –12V is less than +/-3% while
measuring at rated loadin g and +/-10% of input voltage
changing.
$ Load Regulation:
− The load regulation for + 5V, +12Vare less than +/-3%, for
-12V is less than +/-5%, measuring is done by changing
the measured output loading +/-40% from 60% rated
load, and keep other output at 60 % rated load.
Power Supply Specifications
21
Page 30
PANEL1080-845 8.4” All-in-One PANEL PC User’s Manual
General Features
General Features
General FeaturesGeneral Features
Efficiency:
$
− The efficiency is 70% typical while measuring at nominal
line and rated load.
$ Protection:
− For some reason the power supply fails to control itself,
the built-in overvoltage protection circuit will shut down
the outputs to prevent damage to external circuits. The
trip point of cr owbar circ uit is ar ound 5.7V to 7.0V. The
power supply will go in to latch-off mode again st short
circuit or over load conditions, and have to turn OFF and
then ON the DC input to restart the power supply.
Environmental Specifications
Environmental Specifications
Environmental SpecificationsEnvironmental Specifications
$ Operating temp. range: 0°C to 50°C with forced air 20cfm
$ Storage temperature range: -40°C to +85°C
International Standards
International Standards
International StandardsInternational Standards
Safety Standards
$ Desi gned to meet the following standards:
UL 1950, CSA 22.2 NO. 234, TUV/LVD EN60 950
EMI Standards
Designed to meet the following limits::
$
FCC docket 20780 curve “B”, EN55022 “B”
22
Power Supply Specifications
Page 31
PANEL1080-845 8.4” All-in-One PANEL PC User’s Manual
(II) +24V DC Powe r Supply
Input Specifications
Input Specifications
Input SpecificationsInput Specifications
$ I nput voltage range: +18V
$ I nput current: 5A at +24V
Output Specifications
Output Specifications
Output SpecificationsOutput Specifications
$ Load Range:
to +36VDC
DC
max.
DC
Output
+5V 0A 10A 4.95V to 5.05V
+12V 0A 1.5A (open) 11.4V to12.6V
-12V 0A 0.3A -11.4V to –12.6V
− The output range of +12V, -12V and down with +5V
setting. At factory, all outputs in 60 % rated load
conditions, the +5V output is set to between 4.95V and
5.05V, and the other outputs are checked to be within
the specified voltage accuracy range.
Min. Load
Rated Load
Voltage Accuracy
$ Ripple and Noise:
− The peak-to-peak ripple and noise for +5V output is less
than 50mV and less than 100mV for +/-12V outputs.
Measuring is done by 15MHz bandwidth limited
oscilloscope and terminated each output with 0.47uF
capacitor.
$ Line Regulation:
− The line regulation for +5V output is less than +/-1%, for
+12V is less than +/-2%, for –12V is less than +/-3% while
measuring at rated loadin g and +/-10% of input voltage
changing.
$ Load Regulation:
− The load regulation for + 5V is less than +/-3%, for +12V is
less than +/-5%, -12V is less than +7% -3%, measuring is
done by changing the measured output loading +/-40%
from 60% rated load, and keep other output at 60%
rated load.
Power Supply Specifications
23
Page 32
PANEL1080-845 8.4” All-in-One PANEL PC User’s Manual
General Features
General Features
General FeaturesGeneral Features
Efficiency:
$
− The efficiency is 75% typical while measuring at nominal
line and rated load.
$ Protection:
− For some reason the power supply fails to control itself,
the built-in overvoltage protection circuit will shut down
the outputs to prevent damage to external circuits. The
trip point of cr owbar circ uit is ar ound 5.7V to 7.0V. The
power supply will go in to latch-off mode again st short
circuit or over load conditions, and have to turn OFF and
then ON the DC input to restart the power supply.
Environmental Specifications
Environmental Specifications
Environmental SpecificationsEnvironmental Specifications
$ Operating temp. range: 0°C to 50°C with forced air 20cfm
$ Storage temperature range: -40°C to +85°C
International Standards
International Standards
International StandardsInternational Standards
Safety Standards
$ Desi gned to meet the following standards:
UL 1950, CSA 22.2 NO. 234, TUV/LVD EN60 950
EMI Standards
Designed to meet the following limits:
$
FCC docket 20780 curve “B”, EN55022 “B”
24
Power Supply Specifications
Page 33
PANEL1080-845 8.4” All-in-One PANEL PC User’s Manual
(III) +48V DC Power Supply
Input Specifications
Input Specifications
Input SpecificationsInput Specifications
$ I nput voltage range: +36V
$ I nput current: 3A at +48V
Output Specifications
Output Specifications
Output SpecificationsOutput Specifications
$ Load Range:
to +72VDC
DC
max.
DC
Output
+5V 0A 10A 4.95V to 5.05V
+12V 0A 1.5A 11.4V to12.6V
-12V 0A 0.3A -11.4V to –12.6V
− At factory, all outputs in 60% rated load conditions, the
+5V output is set to between 4.95V and 5.05V, and the
other outputs are checked to be within the specified
voltage accuracy range.
Ripple and Noise:
$
− The peak-to-peak ripple and noise for +5V output is less
than 60mV and less than 100mV for +/-12V outputs.
Measuring is done by 15MHz bandwidth limited
oscilloscope and terminated each output with 0.47uF
capacitor.
Line Regulation:
$
− The line regulation for +5V output is less than +/-1%, for
+12V is less than +/-2%, for –12V is less than +/-3% while
measuring at rated loadin g and +/-10% of input voltage
changing.
Load Regulation:
$
− The load regulation for + 5V is less than +/-3%, for +12V is
less than +/-5%, -12V is less than +7% -3%, measuring is
done by changing the measured output loading +/-40%
from 60% rated load, and keep other output at 60%
rated load.
Min. Load
Rated Load
Voltage Accuracy
Power Supply Specifications
25
Page 34
PANEL1080-845 8.4” All-in-One PANEL PC User’s Manual
General Features
General Features
General FeaturesGeneral Features
Efficiency:
$
− The efficiency is 75% typical while measuring at nominal
line and rated load.
$ Protection:
− For some reason the power supply fails to control itself,
the built-in overvoltage protection circuit will shut down
the outputs to prevent damage to external circuits. The
trip point of cr owbar circ uit is ar ound 5.7V to 7.0V. The
power supply will go in to latch-off mode again st short
circuit or over load conditions, and have to turn OFF and
then ON the DC input to restart the power supply.
Environmental Specifications
Environmental Specifications
Environmental SpecificationsEnvironmental Specifications
$ Operating temp. range: 0°C to 50°C with forced air 20cfm
$ Storage temperature range: -40°C to +85°C
International Standards
International Standards
International StandardsInternational Standards
Safety Standards
$ Desi gned to meet the following standards:
UL 1950, CSA 22.2 NO. 234, TUV/LVD EN60 950
EMI Standards
Designed to meet the following limits:
$
FCC docket 20780 curve “B”, EN55022 “B”
26
Power Supply Specifications
Page 35
PANEL1080-845 8.4” All-in-One PANEL PC User’s Manual
A p p e n d i x B
General Care & Maintenance
Aside from the Safety Precautions listed on the front of this User’s
Manual, listed in this appendix are some more additional reminders
and measures users must take when cleaning the LCD panel of
PANEL1080-845.
The following are graphical descriptions of allowable and restricted
cleaning materials. Please remember to wipe off the surface of your
LCD panel using a clean or damp cloth. Both LCD panel and
touchscreen incorporate components that are highly sensitive to water
and strong solutions. Do not use a soaked cloth when wiping off the
dirt as this may cause electrical damages to your LCD panel.
PWR
HDD
T/R
Thinner
Organic solvent
Strong acid
General Care & Maintenance
PWR
HDD
T/R
Neutral
Detergent
27
Page 36
PANEL1080-845 8.4” All-in-One PANEL PC User’s Manual
This page does not contain any information.
28
General Care & Maintenance
Loading...