AXIOMTEK P6187W, P6157W User Manual

P6187W/P6157W
18.5WXGA TFT Monitor
15.6” WXGA TFT Monitor
User’s Manual
ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information. Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third partys rights, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy, completeness or usefulness of any information in this document. Axiomtek does not make any commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Axiomtek Co., Ltd.
CAUTION
If you replace wrong batteries, it causes the danger of explosion. It is recommended by the manufacturer that you follow the manufacturers instructions to only replace the same or equivalent type of battery, and dispose of used ones.
Copyright 2013 Axiomtek Co., Ltd.
All Rights Reserved Dec 2013, Version A1 Printed in Taiwan
iii
Safety Precautions
Before getting started, read the following important cautions.
1. Be sure to ground yourself to prevent static charge when installing the internal components. Use a grounding wrist strap and place all electronic components in any static-shielded devices. Most electronic components are sensitive to static electrical charge.
2. Disconnect the power cords from the P6187W/P6157W Series before making any installation. Be sure both the system and the external devices are turned OFF. Sudden surge of power could ruin sensitive components. Make sure the P6187W/P6157W Series is properly grounded.
3. Do not open the system’s top cover. If opening the cover for maintenance is a must, only a trained technician is allowed to do so. Integrated circuits on computer boards are sensitive to static electricity. To avoid damaging chips from electrostatic discharge, observe the following precautions:
Before handling a board or integrated circuit, touch an unpainted portion of the
system unit chassis for a few seconds. This will help to discharge any static electricity on your body.
When handling boards and components, wear a wrist-grounding strap, available
from most electronic component stores.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd. Windows® is a trademark of Microsoft Corporation.
IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation. Intel® and Pentium® are trademarks of Intel Corporation.
AMI is trademark of American Megatrend Inc. Other brand names and trademarks are the properties and registered brands of their
respective owners.
iv
Table of Contents
Disclaimers ..................................................................................................... ii
Safety Precautions ........................................................................................ iii
Chapter 1 Introduction ............................................. 1
1.1 General Description ............................................................................ 1
1.2 Features ............................................................................................... 2
1.3 Specifications ...................................................................................... 2
1.4 Dimensions and Outlines ................................................................... 3
1.5 I/O Outlets ............................................................................................ 5
1.6 Packing List ......................................................................................... 6
Chapter 2 System Setup .......................................... 7
2.1 System Configuration ......................................................................... 7
2.2 Panel mounting ................................................................................... 8
2.3 Wall mounting ...................................................................................... 9
Appendix A Supported Input Timing Modes ............. 11
Supported Input Timing Modes ................................ ................................ .. 11
Appendix B OSD Operation ........................................ 13
Function Description of OSD Menu ............................................................ 13
P6187W/P6157W User’s Manual
Introduction 1
Chapter 1
Introduction
This chapter contains general information and detailed specifications of the P6187W/P6157W. Chapter 1 includes the following sections:
General Description Features Specification Dimensions I/O Outlets Package List
1.1 General Description
The P6187W/P6157W, a industrial 18.5/15.6 inches view area LCD Monitor comes with slim, light and reliable features to replace traditional bulky CRT for Industrial application. Its unique flat design is fit for panel mounting or VESA mounting. The display interface offers VGA-in, DVI, S-Video, and Video standard interfaces for different input source from PC system or multimedia system that let you upgrade the display don’t change anything from your system. Besides, for varied HMI field, you can choose one of projective capacitive or glass interface to meet your application. In addition, this monitor has more comfort, safety, and environmental protection for humanized & health consideration those would be the benefit that users can get.
This LCD monitor builds in color active matrix thin-film-transistor (TFT) liquid crystal display to provide superior display performance. A maximum resolution of 1366x768 is ideal for displaying complex graphics and high definition images. Other outstanding designs that
enhance this LCD monitor’s performance are Plug & Play compatibility, and OSD (On Screen
Display) controls, especially OSD, it made you ease adjustment on screen image.
P6187W/P6157W User’s Manual
2 Introduction
1.2 Features
High contrast color 18.5/15.6WXGA TFT LCD display support resolution up to
1366x768
Flat design with NEMA4/IP65-compliant Suits with project capacitive or glass High Brightness and Ultra-wide viewing angle with anti-glare features. Power management system conforms to VESA DPMS standard Advanced OSD control for picture quality adjustment Supports VESA ARMs, Desktop Stand Rear, Panel, Wall mounting
1.3 Specifications
18.5”/15.6” WXVGA(1366x768) LCD with LED backlight Projected Capacitive Touch Flat design with NEMA4/IP65 Control: OSD (On Screen Display) control pad on the side Mounting: Support Panel mount, VESA arm mounting, and Wall mount
(optional)
Net Weight
P6187W: 4.8KGS P6157W: 4KGS
Dimension (Main Body Size)
P6187W: 595X490X190 mm P6157W: 525X186X470 mm
Operation Temperature
-10 to 50
Relative Humidity
20% to 90% @ 40, Non-Condensing
Power input
Screw-type external AC DC power adaptor Max power consumption: 22W
NOTE All specifications and images are subject to change without notice.
P6187W/P6157W User’s Manual
Introduction 3
1.4 Dimensions and Outlines
The following diagrams show the dimensions and outlines of P6187W.
P6187W/P6157W User’s Manual
4 Introduction
The following diagrams show the dimensions and outlines of P6157W.
P6187W/P6157W User’s Manual
Introduction 5
1.5 I/O Outlets
Please refer to the following illustration for I/O locations of the P6187W/P6157W.
No
Function
No
Function
1
Exit/Auto Adjust
7
Screw type or Phoenix type power input
2
Menu
8
T/S port
3
SEL-
9
DVI-D
4
SEL+
10
VGA
5
Power LED
11
Video (AV)
6
Power Switch
12
S-video
P6187W/P6157W User’s Manual
6 Introduction
1.6 Packing List
When you receive the P6187W or P6157W, the bundled package should contain the following items:
P6187W unit x 1 or P6157W unit x1 VGA cable x1 DVI cable x1 USB cable x1 (for Projective Capacitive touch version only ) Adaptor x1 (for AC version only) P6187W : Panel mount kit x 12
P6157W : Panel mount kit x 9
If you can not find the package or any items are missing, please contact Axiomtek distributors immediately.
P6187W/P6157W User’s Manual
System Setup
7
Chapter 2
System Setup
This chapter details the system parts and components with figures. Sections include:
System Configuration Panel Mounting Wall Mounting
2.1 System Configuration
The figure below shows the side views of P6187W/P6157W series.
1. Exit:
Jump out the selection icon . Auto adjust.
2. Menu: Press this button to turn on/off the OSD (On Screen Display) main menu. Press this button to activate selected items.
3. SEL-: To scroll down the menu. To decrease the value of selected item.
4. SEL+: To scroll up the menu. To increase the value of selected item.
5. Power LED: When the light is green, the power is on, red light when stand by.
6. Power switch: Press this button to turn on/off the monitor.
P6187W/P6157W User’s Manual
8 System Setup
2.2 Panel mounting
The P6187W/P6157W is designed for panel mount application. To mount the P6187W/P6157W, the standard set of mounting kit (included in the system packaging) is needed.
P6187W Panel Mount kits
P6157W Panel Mount kits
P6187W/P6157W User’s Manual
System Setup
9
2.3 Wall mounting
The P6187W/P6157W provides VESA mount and wall mount. Screw four screws to fix the kit in the back chassis.
P6187W/P6157W User’s Manual
10 System Setup
This page is intentionally left blank.
P6187W/P6157W User’s Manual
Supported Input Timing Modes
11
Appendix A
Supported Input Timing Modes
Supported Input Timing Modes
SPEC
MODE
Pixel
Freq.
Horizontal Timing
Vertical Timing
Sync
Polar
Freq.
Total
Active
Sync
Polar
Freq.
Total
Active
MHZ
KHz
Pixel
Pixel
Hz
Line
Line
640×350
@70Hz
24.144 VESA
P
31.430
800
640 N 70.000
449
350
640×480
@60Hz
25.175 VESA
N
31.469
800
640 N 59.940
525
480
640×480
@60Hz
25.175 VESA
N
31.469
800
640 N 59.940
525
480
640×480
@72Hz
31.500 VESA
N
37.861
832
640 N 72.809
520
480
640×480
@75Hz
31.500 VESA
N
37.500
840
640 N 75.000
500
480
720×400
@70Hz
28.287 VESA
N
31.430
900
720 P 70.000
449
400
800×600
@56Hz
36.000 VESA
P
35.156
1024
800 P 56.250
625
600
800×600
@60Hz
40.000 VESA
P
37.879
1056
800 P 60.317
628
600
800×600
@72Hz
50.000 VESA
P
48.077
1040
800 P 72.188
666
600
800×600
@75Hz
49.500 VESA
P
46.875
1056
800 P 75.000
625
600
NOTE: Timing depends on LCD Panel’s requirement.
P6187W/P6157W User’s Manual
12 Supported Input Timing Modes
SPEC
MODE
Pixel Freq.
Horizontal Timing
Vertical Timing
Sync
Polar
Freq.
Total
Active
Sync
Polar
Freq.
Total
Active
MHZ
KHz
Pixel
Pixel
Hz
Line
Line
1024×768
@60Hz
65.000 VESA
N
48.363
1344
1024
N
60.005
806
768
1024×768
@60Hz
64.000 VESA
N
48.780
1312
1024
N
60.001
813
768
1024×768
@70Hz
75.000 VESA
N
56.476
1328
1024
N
70.070
806
768
1024×768
@75Hz
80.000 VESA
N
60.241
1328
1024
N
74.927
804
768
1024×768
@75Hz
78.750 VESA
P
60.023
1312
1024
P
75.030
800
768
1366x768
@60Hz
85.5
VESA
P
47.712
1792
1366
P
59.79
798
768
P6187W/P6157W User’s Manual
OSD Operation 13
Appendix B
OSD Operation
Function Description of OSD Menu
The layout and format of OSD depends on customer’s request.
OSD MENU
Description
General
Adjust the List
Brightness of the screen.  Contrast of the screen.  Horizontal size of the screen’s image. (for VGA input only) Vertical size of the screen’s image. (for VGA input only) Horizontal position of the screen’s image. (for VGA input only) Vertical position of the screen’s image. (for VGA input only) Sharpness of the screen’s image.
Color
9300K , 7500K and 6500K Temperature, user Temperature .
Languages
Multi language support 8 languagesEnglish, French, German, Spanish, Italian, Japanese, Russian and Chinese .
Tools
Adjust the List
OSD Time out .  OSD position .  OSD Transparent.  Recall : “Yes” allows you to recover to the preset mode . Auto Adjust…Horizontal position, Vertical position, Horizontal size, Phase
of the screen’s image .
White balance
Choose Source
Choose Source: (option)
Analog (VGA)  Digital (DVI)  Analog(S-Video)  Analog(CVBS)
This page is intentionally left blank.
Loading...