AXIOMTEK NA-0043A, NA-0043C, NA-0043G, NA-1531, NA-1801 Hardware Installation Manual
NA-0043 Series
Hardware Installation Guide
For service person only
Disclaimers
The information in this manual has been carefully checked and is believed to be
accurate. AXIOMTEK Co., Ltd. assumes no responsibility for any infringements of
patents or other rights of third parties, which may result from its use.
AXIOMTEK assumes no responsibility for any inaccuracies that may be contained in
this document. AXIOMTEK makes no commitment to update or to keep current the
information contained in this manual.
AXIOMTEK reserves the right to make improvements to this document and/or
product at any time and without notice.
No part of this document may be reproduced, stored in a retrieval system, or
transmitted, in any form or by any means, electronic, mechanical, photocopying,
recording, or otherwise, without the prior written permission of AXIOMTEK Co.,
Ltd.
Copyright 2005 by AXIOMTEK Co., Ltd.
All rights reserved.
Version A1 July 2005
Printed in Taiwan
ii
Safety Approvals
CE Marking
FCC Class A
FCC Compliance
This equipment has been tested and complies with the limits for a
Class A digit al device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection a gainst harmful
interference in a residential installation. If not installed and used in
accordance with proper instructions, this equipment might generate or
radiate radio frequency energy and cause harmful interference to
radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equip m ent
does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measurers:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Shielded interface cables must be used in order to comply with
emission limits.
iii
Safety Precautions
Before getting started, read the following important cautions.
1. Be sure to ground yourself to prevent static charge when
installing the internal components. Use a grounding wrist strap
and place all electronic components in any static-shielded
devices. Most electronic components are sensitive to static
electrical charge.
2. Disconnect the power cords from the NA-0043 before making any
installation. Be sure both the system and the external devices are
turned OFF. Sudden surge of power could ruin sensitive
components. Make sure the NA-0043 is properly grounded.
3. Do not open the system’s top cover. If opening the cover for
maintenance is a must, only a trained technician is allowed to do
so. Integrated circuits on computer boards are sensitive to static
electricity. To avoid damaging chips from electrostatic discharge,
observe the following precautions:
9 Before handling a board or integrated circuit, touch an unpainted
portion of the system unit chassis for a few seconds. This will help
to discharge any static electricity on your body.
9 When handling boards and components, wear a wrist-grounding
strap, available from most electronic component stores.
Trademarks Acknowledgments
AXIOMTEK is a trademark of AXIOMTEK Co., Ltd.
Other brand names and trademarks are the properties of their
respective owners.
iv
Table of Contents
C h a p t e r 1........................................................................................1
1.1 General Description....................................................1
1.2 Standard Features......................................................3
1.3 System Specifications.................................................4
1.3.1 Hardware............................................................4
1.4 Dimensions.................................................................6
1.5 Front Panel Outlets.....................................................7
1.6 Rear Panel Outlets.....................................................8
1.7 Indications of Front Panel...........................................9
C h a p t e r 2 ...................................................................................11
2.1 Preinstallation Checklist ...........................................11
2.2 Setting up the appliance.......................................... 12
2.2.1 Removing and Replacing the Top Cover........ 12
2.2.2 Installing a memory module (DIMM)............... 12
2.2.3 Installing a ATA66/100/133 hard drive............ 12
2.2.4 Connectors & Jumpers ................................... 13
2.2.5 Installing Display Interface.............................. 15
2.2.6 Installing Serial Port Interface......................... 15
2.2.7 Installing Keyboard and PS/2 Mouse
Connectors
2.2.8 Installing USB Connector (Optional)............... 17
2.2.9 Enabling LAN by-pass feature........................ 18
C h a p t e r 3..................................................................................... 21
3.1 BIOS Introduction .................................................... 21
3.2 BIOS Setup.............................................................. 21
3.3 Standard CMOS Setup............................................ 23
....................................................................... 16
v
3.4 Advanced BIOS Features........................................ 27
3.5 Advanced Chipset Features.................................... 31
3.6 Integrated Peripherals............................................. 35
3.7 Power Management Setup...................................... 40
3.8 PNP/PCI Configuration............................................ 41
3.9 PC Health Status ..................................................... 44
3.10 Load Optimized Defaults......................................... 45
3.11 Set Supervisor/User Password................................ 46
3.12 Save & Exit Setup.................................................... 48
3.13 Quit Without Saving................................................. 49
A p p e n d i x A............................................................................... 51
vi
NA-0043 Hardware Installation Guide
C h a p t e r 1
Introduction
This chapter contains the general information and the detailed
specifications of the NA-0043 series Network Appliance server.
Chapter 1 includes the following sections:
General Description Mechanical Dimensions
Features I/O Outlets
System Specifications
1.1 General Description
NA-0043A and NA-0043C Front View (slim type)
Introduction 1
NA-0043G Front View (1U type)
NA-0043 Hardware Installation Guide
Model
Number
Form Factor Number of
LAN Ports
MiniPCI
CPU Compact
Flash
Fanless
NA-0043A Slim 4
x10/100Mb
ps (Realtek
8100C)
NA-0043C Slim 4 x
10/100Mbp
s (Intel
82551)
NA-0043G 1U,
Desktop
* Intel Ultra Low Voltage Celeron M, 600MHz, Zero Cache
** Intel 479-pin socket for Pentium M FSB400 processor
4 x
10/100Mbp
s (Intel
82551)
x
x
3
* x
* x
**
3
3
3
x
The NA-0043 series server is designed for network software solution
providers those have data secure, voice over IP, video streaming,
network bandwidth controller and another networking appliance
requirements across this stable and reliable multiple LAN device.
They have slim type with FAN less and 1U type with high computing
design form factor. There can be deployed up to four LAN ports
combinations for customer selection in the maximum for application.
They also can support LAN by-pass features (for NA-0043A,
NA-0043Cand NA-0043G) which can isolate the defective segment s.
NA-0043 series has pretty good enclosure management interface to
be implemented in the factory default. It can support P.O.S.T (Power
On Self Test) feature through hyper-terminal by console port. And
clear LED indicators is available for statu s t racking by customer.
2 Introduction
NA-0043 Hardware Installation Guide
And it has room space for one 2.5” hard drive deployment. Customer
can implement system log and monitoring functions through this
hardware specification. With its
design, the NA-0043 series (for NA-0043G) server provides one mini-PCI
expansion slot for VPN encryption / decryption adapter board and another
special functions enabling. It cans
process performance and off loads the CPU loading.
The NA-0043 series is an excellent networking application platform for
network secure in the SOHO (Small Office and Home Office) market.
innovative mechanical and electrical
enhancement network security
1.2 Standard Features
z Ultra Low Voltage In tel® Celeron® M processor , low
power consumption and high computing power Æ For
NA-0043A, NA-0043C. And Intel® Pentium® M processor
is for NA-0043G.
z
Supports four Ethernet ports
z
Supports LAN bypass and BIOS redirected to COM port
features
z
Completely fanless or 1U desktop system design.
z
Supports accelerate IPsec and incorporates security
engines through Mini PCI socket
z
Supports RS-232, 2 USB ports and CF (For NA-0043G)
z
Suitable for network appliances: VPN, Network Bandwidth
Controller, SSL/TLS, Firewall, etc,.
Introduction 3
NA-0043 Hardware Installation Guide
1.3 System Specifications
1.3.1 Hardware
z Form Factor:
Slim type FAN less design and 1U desktop
z Capacity:
It is from 0 to 250GB and beyond, depending on the 2.5” hard
disk drive capacity.
z Power Supply:
External power adapter 12V, 5A (60W)
z Hard Driv e:
Spacing for 1 x IDE HDD ( 2.5”)
z Front Connector :
1 x Console port
z Front Panel LED:
1 x LED for HDDs
8 x LED for LANs (Four of them are for per port Link and Activit y,
other of them are for per port transfer rate)
1 x Power LED for System
z Rear Connector:
4 x Ethernet LAN port
1 X DC-in power connector
z Processor:
Intel ULV Celeron M processor
Zero cache and 600MHz Æ For NA-0043A, NA-0043C,
Pentium M processor Æ For NA-0043G
Intel
4 Introduction
NA-0043 Hardware Installation Guide
z BIOS:
Award 4MB Flash BIOS Plug & Play
z Main Memory:
One DDR266 SODIMM memory can be up to 1GB in the
maximum
z IDE Interface:
Support two ATA 66/100/133 EIDE channels (44-pins)
z Serial Port:
One DB9 connector, other one is Pin reserved
z Ethernet:
Totally has four LAN port connections are available.
Two ports of them support LAN by-pass feature Æ For
NA-0043A, NA-0043C and NA-0043G,
z Expansion:
One Mini-PCI slot is for security encryption card or specialize
functions expansion Æ For NA-0043G
z Compact-FlashTM:
One IDE interface CompactFlash
(Optional, upon for customer requirement)
TM
socket for embedded use
z Dimensions:
214mm (W) x 30mm (H) x 150.8mm (D) Æ NA-0043A,
NA-0043C,
214mm (W) x 44mm (H) x 150.8mm (D) Æ NA-0043G
z Operation environment:
Air temperature: 10° C – 45°C (50°F – 113°F)
Humidity: 10% – 95%
z Storage environment:
Air temperature: -20° C – 7 0°C
Humidity: 10% – 95%
Introduction 5
NA-0043 Hardware Installation Guide
1.4 Dimensions
Unit: mm
6 Introduction
NA-0043 Hardware Installation Guide
1.5 Front Panel Outlets
Located at the front panel of the NA-0043 series server are the I/O
outlets for connections of serial and Ethernet interface-supported
devices.
The NA-0043 Series Server Front Panel
LAN link / transfer rate
Console port – DB-9 RS-232 Console port for command line
interface and diagnostic support by P.O.S.T (Power On Self
Test).
Console Port
Power – Lights when the NA-0043 is powered up and
performing diagnostic tests to check for proper operation.
LAN Link – Lights up with a Twisted pair connection is made to
another Ethernet device on the port.
Transfer Rate – Show network transfer rate while make
connections
Activity – Lights up when the NA-0043 transmits or re ceives a
packet through the twisted pair port
Introduction 7
NA-0043 Hardware Installation Guide
1.6 Rear Panel Outlets
Located at the rear panel of the NA-0043 server are the I/O outlets.
12V, 5A
DC power
input
LAN Ports USB Ports
8 Introduction
NA-0043 Hardware Installation Guide
1.7 Indications of Front Panel
I. Power on LED
1. System and power on
II. HDD LED
Link/Active LED (single color)
1. The green LED is on when the HD has connection normally
2. The LED flashes when the re is transmit or receive activity
III. Link/Active LED (Single color)for LAN port #1, port#2,
port#3 and port#4
1. The yellow LED is on when there is an active con nection on
the LAN port
2. The LED flashes when there is transmit or receive activity to
or from the appliance
3. The LED is dark when it of f line.
IV. Transmitted LED for LAN port #1, port#2, port#3 and port#4
1. The green L ED light is on 10/100Mbps transfer rate
2. The LED is dark if the Link/Active LED is light or flash in the
Introduction 9
NA-0043 Hardware Installation Guide
same time; It’s on 10Mbps transfer rate
3. The LED is dark if the Link/Active LED is dark also.
There is no any networking device was attached.
10 Introduction
NA-0043 Hardware Installation Guide
C h a p t e r 2
Installation Procedures
2.1 Preinstallation Checklist
In addition to this installation guide, make sure you have the following
items,
The NA-0043 series network appliance hardware platform
Power cord
Utility CD (including this installation guide)
Mounting screws for disk drive and screws used in this
appliance for spare
Hardware Installation Guide
NA-0043 cable kits (1 x 44-pin IDE, 1 x console cable, 1 x
PS/2 keyboard and mouse cable, 1 x VGA cable)
Plastic stand for stack–up x 4
If you ordered options for the appliance, this package might contain
additional hardware or publications for those options.
.
Installation Procedures 1 1
NA-0043 Hardware Installation Guide
2.2 Setting up the appliance
This section provides the information about the initial installation to
setup the NA-0043
2.2.1 Removing and Replacing the Top Cover
To gain access into the internal components of the NA-0043, you
must follow the instructions given below to remove the top cover.
Please release the screws of lower case and left with right side first,
XMain Board
2.2.2 Installing a memory module (DIMM)
The main board can supports one SODIMM DDR socket for a
maximum total memory up to 1GB
The device can support Single-Channel Operation
None-ECC unbuffer Memory.
1. In single-channel operation DIMM2 is disabled. Only DIMM1 need
be added.
Attention: X When you handle electrostatic discharge-sensitive
(ESDs), take precautions to avoid damage from static
electricity.
Y The memory can support DDR266.
2.2.3 Installing a ATA66/100/133 hard drive
To accommodate the fast transfer rate of Ultra ATA/66/100/133, a
cable (with 44 pin connectors on both ends) is necessary when
12 Installation Procedures
Loading...