AXIOMTEK MMT175 User Manual

MMT175

17” TFT Medical Grade LCD Monitor

User’s Manual

Disclaimers

This manual has been carefully checked and believed to contain
accurate information. AXIOMTEK Co., Ltd. assumes no responsibility
for any infringements of patents or any third party’s rights, and any
liability arising from such use.
AXIOMTEK does not warrant or assume any legal liability or
responsibility for the accuracy, completeness or usefulness of any
information in this document. AXIOMTEK does not make any
commitment to update the information in this manual.

AXIOMTEK reserves the right to change or revise this document
and/or product at any time without notice.

No part of this document may be reproduced, stored in a retrieval
system, or transmitted, in any form or by any means, electronic,
mechanical, photocopying, recording, or otherwise, without the prior
written permission of AXIOMTEK Co., Ltd.

©Copyright 2009 AXIOMTEK Co., Ltd.

All Rights Reserved
December 2009, Version A1
Printed in Taiwan

ii

Safety Approvals

 CE Marking
 UL60601-1
 EN60601-1
 FCC Class B

 FCC Compliance

This equipment has been tested in compliance with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are meant to provide reasonable protection against harmful
interference in a residential installation. If not installed and used in
accordance with proper instructions, this equipment might generate or
radiate radio frequency energy and cause harmful interference to
radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following methods:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment to another outlet of a circuit that
doesn’t connect with the receiver.

4. Consult the dealer or an experienced radio/TV technician for
help.

Shielded interface cables must be used in order to comply with the
emission limits.

iii

Safety Precautions

Before getting started, please read the following important safety
precautions.

1. The MMT175 does not come equipped with an operating

system. An operating system must be loaded first before
installing any software into the computer.

2. Be sure to ground yourself to prevent static charge when

installing the internal components. Use a grounding wrist
strap and place all electronic components in any static­shielded devices. Most electronic components are sensitive
to static electrical charge.

3. Disconnect the power cord from the MMT175 before any

installation. Be sure both the system and external devices
are turned OFF. A sudden surge of power could ruin
sensitive components that the MMT175 must be properly
grounded.

4. The brightness of the flat panel display will be getting weaker

as a result of frequent usage. However, the operating period
varies depending on the application environment.

5. Turn OFF the system power before cleaning. Clean the

system using a cloth only. Do not spray any liquid cleaner
directly onto the screen. Although the touchscreen is
chemical resistant, it is recommended that you spray the
liquid cleaner on a cloth first before wiping the screen.

6. Avoid using sharp objects to operate the touchscreen.

Scratches on the touchscreen may cause malfunction or
internal failure to the touchscreen.

7. The flat panel display is not susceptible to shock or vibration.

When assembling the MMT175, make sure it is securely
installed.

8. Do not open the system’s back cover. If opening the cover

for maintenance is a must, only a trained technician is
allowed to do so. Integrated circuits on computer boards are
sensitive to static electricity. To avoid damaging chips from
electrostatic discharge, observe the following precautions:

iv

z Before handling a board or integrated circuit, touch an

unpainted portion of the system unit chassis for a few
seconds. This will help to discharge any static
electricity on your body.

z When handling boards and components, wear a wrist-

grounding strap, available from most electronic
component stores.

Trademarks Acknowledgments

AXIOMTEK is a trademark of AXIOMTEK Co., Ltd.
PC/AT, VGA are trademarks of International
Business Machines Corporation.

®

is registered trademarks of Intel Corporation.

Intel
MS-DOS, Microsoft C and Quick BASIC are trademarks of Microsoft
Corporation.
VIA is a trademark of VIA Technologies, Inc.
SST is a trademark of Silicon Storage Technology, Inc.
UMC is a trademark of United Microelectronics Corporation.
Other brand names and trademarks are the properties and registered
brands of their respective owners.

v

Table of Contents

Disclaimers..........................................................................ii

Safety Approvals.................................................................iii

Safety Precautions..............................................................iv

CHAPTER 1 INTRODUCTION .......................................1

1.1 General Description............................................ 1

1.2 Package List.......................................................3

1.3 Specifications......................................................4

1.4 Dimensions......................................................... 5

1.5 I/O Outlets...........................................................6

CHAPTER 2 SYSTEM SETUP.......................................8

2.1 System Configuration .........................................8

2.2 OSD Setting......................................................10

2.3 Mount Methods................................................. 13

2.3.1 Wall Mount................................................................ 13

2.3.2 VESA mount ............................................................. 14

2.3.3 Desktop Stand .......................................................... 15

CHAPTER 3 DRIVERS INSTALLATION.......................20

3.1 System..............................................................20

3.2 Touch Screen ...................................................20

3.2.1 Specification..............................................................20

3.2.2 Driver Installation- Windows XP ............................... 21

3.3 Bluetooth (optional)...........................................24

vi

MEMO

vii

MMT175 User’s Manual

CHAPTER 1

INTRODUCTION

This chapter contains the general information and detailed
specifications of the MMT175. Chapter 1 includes the following
sections:

 General Description
 Specification
 Dimensions
 I/O Outlets
 Package List

1.1 General Description

The MMT175 is a Medical Grade LCD Monitor. It adopts a 17” 300nits
SXGA LCD display, and numerous signal interfaces including DVI,
VGA, S-Video, Video, Audio-in and 3 USB (1 slave, 2 hosts). There is
an OSD function making you ease adjustment on screen image. The
MMT175 has more comfort, safety, and environmental protection for
humanized & health consideration those would be the benefit that
users can get.

¾ Medical-grade Product Design

The features of the MMT series are low-noise operation, low­power consumption and high reliability. And the MMT175
conforms UL60601-1, EN60601-1 and FCC class B. Thus, it is
best suited for medical environment applications.

Introduction

1

MMT175 User’s Manual

¾ Spill and dust resistant

The MMT175 has water-proof design of the IP65 front panel and
IPx1 whole enclosure so the entire system is protected from
water drip damages.

¾ Multi-Display Mode supports

Support VGA (640 x 480), SVGA (800 x 600), XGA (1024 x 768),
SXGA (1280 x 1024).

¾ Multi-signal inputs

Support VGA, S-video, video, DVI, Audio-in, 3 USB ports (2 ×
type A, 1 × type B), so the MMT175 can receives TV and PC

signals.

2

Introduction

MMT175 User’s Manual

1.2 Package List

When you receive the MMT175, the bundled package should contain
the following items:

z MMT175 x 1
z Driver CD x1
z Medical Power Adapter x1
z USB cable x 1
z Audio cable x 2
z VGA cable x 1
z Wall mount kit
z Desktop Stand Kit (optional)
z VESA ARM(optional)

If you can not find the package or any items are missing, please
contact AXIOMTEK distributors immediately.

Introduction

3

MMT175 User’s Manual

1.3 Specifications

¾ Display Tyep: 17” TFT LCD
¾ Max. Resolution: 1280 x1024
¾ Brightness: 300nits
¾ Max. Colors: 16.7M
¾ View Angle: H:160° / V:160°

¾ Front Bezel: Plastic ABC
¾ Control: OSD (On Screen Display) control pad on front

side

¾ IO outlets

1 x Audio, 1 x VGA, 1 x DVI, 1 x USB (Slave, for DSC, T/S)
2 x USB (Host), 1 x Video, 1 x S-Video

¾ Mounting: Support Wall mount and VESA FPMPMI

mounting.

¾ Operating Temperature Range: 0℃ ~ 45℃
¾ Relative Humidity: 20% ~ 90%; non-condensing

¾ Vibration: 5 to 500 Hz, 2.0 G random

4

Introduction

MMT175 User’s Manual

1.4 Dimensions

This diagram shows you dimensions and outlines of the MMT175.

Introduction

5

MMT175 User’s Manual

1.5 I/O Outlets

Please refer to the following illustration for I/O locations of the
MMT175.

○1

○2 ○3 ○4 ○5 ○6

○7 ○8 ○9 ○10 ○11 ○12 ○13 ○14 ○15 ○16

No Function

6

1 Camera
2 Auto-Adjusted / Return
3 Menu
4 SEL+ / SEL­5 Power LED

Introduction

MMT175 User’s Manual

6 Monitor Switch
7 Audio(Line-out)
8 DVI

9 VGA
10 S-video
11 Video
12 Power switch
13 Audio (Mic-in)

USB2.0 × 2

14
15 USB (type B)
16 DC-in power connector

Introduction

7

MMT175 User’s Manual

CHAPTER 2

SYSTEM SETUP

This chapter details the system parts and components with figures. It
includes:

 System Configuration
 OSD Setting
 Wall Mount / VESA / Desktop Stand methods

2.1 System Configuration

The MMT175 provides display control on screen display. The
descriptions of the functions are listed below.

1. Monitor switch: Press this button to turn on/off the monitor.

2. Power LED: When the light is green, the power is on, flash when
the power is turn off.

3. SEL+: To increase the value of selected item.

4. SEL-: To decrease the value of selected item.

8

1. 3. 2. 4.5. 6.

System Setup

MMT175 User’s Manual

5. Menu: Press this button to turn on/off the OSD (On Screen
Display).

6. Auto-Adjusted / Return: This button is auto image adjustment
and return.

System Setup

9

MMT175 User’s Manual

2.2 OSD Setting

The MMT175 provides OSD (On Screen Display) to adjust brightness,
contrast, clock…et al. Please follow the steps are listed as below.

1. Please press the “Menu” button on the OSD keypad. You could
see General menu. If you want to adjust sub-item, you could
press the “Menu” button on the OSD keypad.

2. Please press the “SEL-“button on the OSD keypad. You will entry
Audio menu. You could adjust volume or mute.

10

System Setup

MMT175 User’s Manual

3. Please press the “SEL-“button on the OSD keypad. You will entry
Color menu. If you want to adjust sub-item, you could press the
“Menu” button on the OSD keypad.

4. Please press the “SEL-“button on the OSD keypad. You will entry
Languages menu. MMT175 support 8 languages (English, French,
German, Spanish, Italian, Japanese, Russian and Chinese).

5. Please press the “SEL-“button on the OSD keypad. You will entry

System Setup

11

MMT175 User’s Manual

Tools menu. If you want to adjust sub-item, you could press the

“Menu” button on the OSD keypad.

6. Please press the “SEL-“button on the OSD keypad. You will entry
Exit menu. If you want to leave the OSD, you would press “menu”.

12

System Setup

MMT175 User’s Manual

2.3 Mount Methods

There are several mounting ways for the MMT175, Wall, VESA and
Desktop mountings.

2.3.1 Wall Mount

The MMT175 provides wall mount kit. Please follow the steps
as below. Prepare all parts for installing the wall mount kit.

Step 2 Assemble the wall mount kit by using screws to fix the
back.

1

○

System Setup

○

2

13

MMT175 User’s Manual

2.3.2 VESA mount

The MMT175 provides two types of VESA mount, 75mm x 75mm and
100mm x 100mm.

14

System Setup

MMT175 User’s Manual

2.3.3 Desktop Stand

The MMT175 provides desktop stand (optional) that customer
can install as below.

Step 1 Prepare the parts of desktop stand.

Screw A Screw B

Screw C Hinge Cover

System Setup

15

MMT175 User’s Manual

Step 2 Assemble the desktop stand. Fix the screws as marked on
the bottom side of chassis. (Use Screw A)

Step 3 Fix the screws as marked on the back side of chassis (Use
Screw B).

16

System Setup

MMT175 User’s Manual

Step 4 Assembly the hinge cover and fix the screws as marked on
the back side of chassis (Use Screw C).

System Setup

17

MMT175 User’s Manual

Step 5 Finish.

18

System Setup

MEMO

MMT175 User’s Manual

System Setup

19

MMT175 User’s Manual

CHAPTER 3

DRIVERS INSTALLATION

3.1 System

MMT175 supports Windows XP. To facilitate the installation of system
driver, please carefully read the instructions in this chapter before start
installing. The installation method of the touch and Bluetooth (optional)
are listed below.

3.2 Touch Screen

The MMT175 uses the 5-wire analog resistive. There are the
specification and driver installation which are listed below.

3.2.1 Specification

Touch Screen
Touch Screen Controller

Communications
Resolution
Power Input
Power Consumption

20

5-wire Analog Resistive type
PenMount 6000 USB

Touch Screen Controller IC
USB interface

1024 x 1024 (10 bit A/D converter inside)
5V

Active: 24.6mA / Idle Mode: 13.4mA

Drivers Installation

MMT175 User’s Manual

3.2.2 Driver Installation- Windows XP

The MMT175 provides a touch screen driver that users can install it
under the operating system Windows XP. To facilitate installation of the
touch screen driver, you should read the instructions in this chapter
carefully before you attempt installation.

1. Insert Driver CD and follow the path to select the
“\Drivers\XP\Step 1 - Touch”.

2. Double chick the icon –“Setup”.

3. Follow the installing procedure and press OK.

Drivers Installation

21

MMT175 User’s Manual

4. Click Start menu and select “PenMount Utilities”; and then, a
“PenMount Control Panel” pops out.

5. Select the “Standard Calibrate” tab.

6. Calibration:

22

Drivers Installation

MMT175 User’s Manual

To adjust the display with touch panel, click “Calibration” and
follow the calibrate point to do calibration; there are five points on
screen for calibration.

7. Press OK.

Drivers Installation

23

MMT175 User’s Manual

3.3 Bluetooth (optional)

The MMT175 provides users to extra add Bluetooth function. Users can
install the Bluetooth driver under the operating system Windows XP. To
facilitate installation of the touch screen driver, you should read the
instructions in this chapter carefully before you attempt installation.

1. Insert Driver CD and follow the path to select the
“\Drivers\XP\Step 2 - Bluetooth (optional)”.

2. Double chick the icon –“Setup”.

3. Follow the installing procedure and press OK.

24

Drivers Installation