AXIOMTEK IPC964-512-FL, IPC962-511-FL User Manual

IPC962-511-FL series

IPC964-512-FL Series

Industrial and Fanless Computers

User’s Manual

ii

Disclaimers

This manual has been carefully checked and believed to contain accurate
information. Axiomtek Co., Ltd. assumes no responsibility for any infringements of
patents or any third party’s rights, and any liability arising from such use.

Axiomtek does not warrant or assume any legal liability or responsibility for the
accuracy, completeness or usefulness of any information in this document. Axiomtek
does not make any commitment to update the information in this manual.

Axiomtek reserves the right to change or revise this document and/or product at any
time without notice.

No part of this document may be reproduced, stored in a retrieval system, or
transmitted, in any form or by any means, electronic, mechanical, photocopying,
recording, or otherwise, without the prior written permission of Axiomtek Co., Ltd.

Copyright 2018 Axiomtek Co., Ltd.

All Rights Reserved
March 2018, Version A3
Printed in Taiwan

iii

Safety Precautions

Before getting started, please read the following important safety precautions.

1. The IPC962-511-FL/IPC964-512-FL Series does not come equipped with an
operating system. An operating system must be loaded first before installing
any software into the computer.

2. Be sure to ground yourself to prevent static charge when installing the
internal components. Use a grounding wrist strap and place all electronic
components in any static-shielded devices. Most electronic components are
sensitive to static electrical charge.

3. Disconnect the power cord from the IPC962-511-FL/IPC964-512-FL Series
before making any installation. Be sure both the system and the external
devices are turned OFF. Sudden surge of power could ruin sensitive
components. Make sure the IPC962-511-FL/IPC964-512-FL Series is
properly grounded.

4. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.

5. Turn OFF the system power before cleaning. Clean the system using a cloth
only. Do not spray any liquid cleaner directly onto the screen.

6. Do not leave this equipment in an uncontrolled environment where the
storage temperature is below -20℃ or above 80℃. It may damage the
equipment.

7. Do not open the system’s back cover. If opening the cover for maintenance
is a must, only a trained technician is allowed to do so. Integrated circuits on
computer boards are sensitive to static electricity. To avoid damaging chips
from electrostatic discharge, observe the following precautions:

 Before handling a board or integrated circuit, touch an unpainted

portion of the system unit chassis for a few seconds. This will help to
discharge any static electricity on your body.

 When handling boards and components, wear a wrist-grounding strap,

available from most electronic component stores.

iv

Classification

1. Degree of production against electric shock: not classified

2. Degree of protection against the ingress of water: IPX40

3. Equipment not suitable for use in the presence of a flammable anesthetic mixture with
air or with oxygen or nitrous oxide.

4. Mode of operation: Continuous

5. Type of protection against electric shock: Class I equipment

General Cleaning Tips

You may need the following precautions before you begin to clean the computer.
When you clean any single part or component for the computer, please read and
understand the details below fully.

When you need to clean the device, please rub it with a piece of dry cloth.

1. Be cautious of the tiny removable components when you use a vacuum cleaner

to absorb the dirt on the floor.

2. Turn the system off before you start to clean up the component or computer.

3. Never drop the components inside the computer or get circuit board damp or

wet.

4. Be cautious of all kinds of cleaning solvents or chemicals when you use it for

the sake of cleaning. Some individuals may be allergic to the ingredients.

5. Try not to put any food, drink or cigarette around the computer.

v

Cleaning Tools:

Although many companies have created products to help improve the process of
cleaning your computer and peripherals users can also use household items to clean
their computers and peripherals. Below is a listing of items you may need or want to
use while cleaning your computer or computer peripherals.

Keep in mind that some components in your computer may only be able to be
cleaned using a product designed for cleaning that component, if this is the case it
will be mentioned in the cleaning.

 Cloth: A piece of cloth is the best tool to use when rubbing up a component.

Although paper towels or tissues can be used on most hardware as well, we
still recommend you to rub it with a piece of cloth.

 Water or rubbing alcohol: You may moisten a piece of cloth a bit with some

water or rubbing alcohol and rub it on the computer. Unknown solvents may
be harmful to the plastics parts.

 Vacuum cleaner: Absorb the dust, dirt, hair, cigarette particles, and other

particles out of a computer can be one of the best methods of cleaning a
computer. Over time these items can restrict the airflow in a computer and
cause circuitry to corrode.

 Cotton swabs: Cotton swaps moistened with rubbing alcohol or water are

excellent tools for wiping hard to reach areas in your keyboard, mouse, and
other locations.

 Foam swabs: Whenever possible it is better to use lint free swabs such as

foam swabs.

Note: It is strongly recommended that you should shut down the system before you

start to clean any single components.

Please follow the steps below:

1. Close all application programs

2. Close operating software

3. Turn off power switch

4. Remove all device

5. Pull out power cable

vi

Scrap Computer Recycling

If the computer equipments need the maintenance or are beyond repair, we strongly
recommended that you should inform your Axiomtek distributor as soon as possible for the
suitable solution. For the computers that are no longer useful or no longer working well, please
contact your Axiomtek distributor for recycling and we will make the proper arrangement.

Trademark Acknowledgments

Axiomtek is a trademark of Axiomtek Co., Ltd.
Intel® and Pentium® are registered trademarks of Intel Corporation.
Windows 10, Windows 10 IoT Enterprise, Windows 7, are trademarks of Microsoft

Corporation.
Other brand names and trademarks are the properties and registered brands of their

respective owners.

vii

Table of Contents

Safety Precautions ................................................................................................ iii

Classification ......................................................................................................... iv

General Cleaning Tips .......................................................................................... iv

Scrap Computer Recycling .................................................................................. vi

CHAPTER 1 INTRODUCTION ................................................................................ 1

1.1 General Description ........................................................................... 1

1.2 System Specifications ....................................................................... 2

1.2.1 Main CPU Board ............................................................................................... 2

1.2.2 I/O System ........................................................................................................ 2

1.2.3 System Specification ....................................................................................... 3

1.3 Dimensions ........................................................................................ 5

1.4 I/O Outlets .......................................................................................... 6

1.5 Packing List ........................................................................................ 8

1.6 Jumper Settings ................................................................................. 9

1.6.1 Restore BIOS Optimal Defaults (JP1) ............................................................ 9

1.7 Connectors ....................................................................................... 10

1.7.1 MINI CARD SLOT (CN3) ................................................................................. 11

1.7.2 LAN+USB3.0 (CN4、CN5).............................................................................. 12

1.7.3 VGA Connector (CN6) ................................................................................... 13

1.7.4 Audio Connector (CN7) ................................................................................. 14

1.7.5 DC-in Phoenix Power Connector (CN8) ....................................................... 14

1.7.6 HDMI Connector (CN9) .................................................................................. 14

1.7.7 SATA Power connector (SCN1、SCN2) ....................................................... 15

1.7.8 SATA Connector (SATA1、SATA2) .............................................................. 15

1.7.9 ATX Power On/OFF Button(SW1) ................................................................. 15

1.7.10 AT/ATX Switch (SW2) .................................................................................... 16

1.7.11 Reset Button(SW3) ........................................................................................ 16

1.7.12 Remote Power Switch Connector (PWRBT1) ............................................. 16

1.7.13 Flexible IO - COM I/O Card Connector (AX93511) ...................................... 17

1.7.14 Riser Card Power output (ATX1-Black,ATX2-White) .................................. 17

CHAPTER 2 HARDWARE INSTALLATION ....................................................... 19

2.1 Installing the Processor .................................................................. 19

2.2 Installing the Memory Module ......................................................... 21

2.3 Installing the Hard Disk Drive ......................................................... 23

2.4 Installing the Fan Module and PCI or PCIe Card ........................... 24

CHAPTER 3 AMI BIOS UTILITY........................................................................... 31

3.1 Starting ............................................................................................. 31

3.2 Navigation Keys ............................................................................... 32

3.3 Main Menu ........................................................................................ 33

3.4 Advanced Menu ................................................................................ 34

3.5 Chipset Menu ................................................................................... 43

viii

3.6 Security Menu .................................................................................. 47

3.7 Boot Menu ........................................................................................ 48

3.8 Save & Exit Menu ............................................................................. 49

APPENDIX A WATCHDOG TIMER ...................................................................... 51

A.1 About Watchdog Timer .................................................................... 51

A.2 How to Use Watchdog Timer .......................................................... 51

A.3 Sample Program .............................................................................. 53

IPC962-511-FL/IPC964-512-FL Series User’s Manual

Introduction

1

CHAPTER 1

INTRODUCTION

This chapter contains general information and a detailed specification of the IPC962­511-FL/IPC964-512-FL Series. Chapter 1 includes the following sections:

 General Description
 System Specifications
 Dimensions
 I/O Outlets
 Jumper Settings
 Connectors
 Package List

1.1 General Description

The IPC962-511-FL/IPC964-512-FL Series is a fanless system that can support
LGA1151 socket for Intel® 6th/7th generation Core

TM

i7/i5/i3 processors. The IPC962-

511-FL/IPC964-512-FL Series supports Windows

®

7, Windows® 10 which are suitable

for the most endurable operation.

 The IPC962-511-FL/IPC964-512-FL Series support two hard-drive bays, which makes

it easy to install for customer maintain the system.

 Embedded O.S. Supported

The IPC962-511-FL/IPC964-512-FL Series not only supports Windows® 7 and
Windows

®

10, but also supports embedded OS, such as Windows® 7 embedded. For
storage device, the IPC962-511-FL/IPC964-512-FL Series supports two 2.5" HDD
driver bay.

IPC962-511-FL/IPC964-512-FL Series User’s Manual

Introduction

2

1.2 System Specifications

1.2.1 Main CPU Board

 CPU

 Socket LGA1151 for 6

th /7th

Generation Intel® Core

TM

i7/i5/i3 processors, up to 35W

 System Chipset

 Intel

®

H110 chipset (IPC962-511)

 Intel

®

Q170 chipset (IPC964-512)

 BIOS

 AMI BIOS, with Smart View and Customer CMOS Backup.

 System Memory

 Two DDR4-2133 un-buffered SO-DIMM max. up to 32GB

 Features

 Fanless Operation
 Compact & Front IO design
 Supports two expansion slots(IPC962-511) or four expansion slots(IPC964-512)

 DC to DC power supply support 24VDC (uMin=19V/uMax=30V)
 Supports two 2.5" HDD

 Supports optional WLAN module & antenna

1.2.2 I/O System

 Standard I/O Interface -- Font

 One ATX power on/off switch
 One ATX/AT Mode switch
 One Reset switch
 One 2-pin connector output for remote power on/off switch
 19VDC to 30VDC with phoenix power plug
 Four USB 3.0 ports
 HDD access/Power LEDs
 Two G.E. LAN ports (i211AT)

 Flexible IO

 AX93511 4 x RS-232/422/485 module (default RS-232) or
 AX93512 2 x RS-232/422/485 w/ isolated 2.5KVDC protection module and

8-in/8-out isolated DIO or

 AX93513 16-in/16-out isolated DIO with interrupt module

 One VGA supports resolution up to 1920 x 1200 @60Hz
 One HDMI.4b supports resolution up to 4096 x 2304 @60MHz

IPC962-511-FL/IPC964-512-FL Series User’s Manual

Introduction

3

 1 x Audio (MIC-in/Line-out)

 Expansion Slot

IPC962-511

 1 x on board full-size PCI Express Mini Card slot with USB interface
 AX96206: 1 PCIe x16 + 1 PCI or
 AX96207: 2 PCI or
 AX96205: 1 PCIe x16 + 1 PCIe x4

IPC964-512

 1 x on board full-size PCI Express Mini Card slot with USB/PCIe interface
 AX96410: 1 PCIex16 + 3 PCIex4 I or
 AX96411: 1 PCIex16 + 1 PCIex4 + 2PCI

Note: The maximum power rating for expansion slots at 60℃ can not be

exceeded the following value.
The maximum loading of +3.3V+5V+12V<150W

Note: 12V maximum loading 10A

(1 20W)

, the remaining 30W is shared by 3.3V

& 5V.

Note: 24V is only for Axiomtek’s add-on card.

1.2.3 System Specification

 Drive Capacity

 Supports two 2.5” HDD driver bay (SSD/HDD thickness<=15mm)

Note: Due to Gen. 2 SSD with JMicron controller has compatibility issue with

Intel H110 PCH, we strongly recommend to use Gen. 3 SSD on IPC962
Series.

 Power Input

 24VDC (uMin=19V/uMax=30V) with phoenix power plug

 Operation Temperature

 Ambient with air flow: -10℃ ~ +60℃with 6th gen CPU and W.T. HDD or W.T. SSD
 Ambient with air flow: -10℃ ~ +50℃with 7th gen CPU and W.T. HDD or W.T. SSD

 Storage Temperature

 -20℃ ~ 80℃

 Humidity

 10% ~ 90% (Non-condensing)

 Dimensions

 147.5 mm (5.81") (W) x 192 mm (7.56") (H) x 230 mm (9.06") (D) (IPC962-511)
 188.1 mm (7.39") (W) x 192 mm (7.54") (H) x 230 mm (9.04") (D) (IPC964-512)

IPC962-511-FL/IPC964-512-FL Series User’s Manual

Introduction

4

Note: All specifications and images are subject to change without notice.

The performance of the system might be adversely affected at an

operatingtemperature above 60° C.

Note: If the operating temperature is above 35 ° C, it is recommended to use a

wide temperature SSD on the device.

IPC962-511-FL/IPC964-512-FL Series User’s Manual

Introduction

5

1.3 Dimensions

The following diagrams show you dimensions and outlines of the IPC962-511-FL/IPC964-512­FL Series.

IPC962-511

IPC964-512

IPC962-511-FL/IPC964-512-FL Series User’s Manual

Introduction

6

1.4 I/O Outlets

The following figures show you I/O outlets on front and rear panels of the IPC962-511­FL/IPC964-512-FL Series.

IPC962-511
Front Panel

IPC962-511-FL/IPC964-512-FL Series User’s Manual

Introduction

7

IPC964-512
Front Panel

IPC962-511-FL/IPC964-512-FL Series User’s Manual

Introduction

8

1.5 Packing List

The package bundled with your IPC962-511-FL/IPC964-512-FL Series should contain the
following items:

 IPC962-511-FL/IPC964-512-FL-DC Series Unit x 1
 Driver CD
 Screw pack x 1
 Foot pad x 4
 CPU grease x 1
 Terminal block x 1
 Remote switch cable x 1
 Holder bracket x1

If you can not find this package or any items are missing, please contact Axiomtek distributors
immediately.

IPC962-511-FL/IPC964-512-FL Series User’s Manual

Introduction

9

1.6 Jumper Settings

Properly configure jumper settings on the SBC87511/SBC87512 to meet your application
purpose. Below you can find a summary table of all jumpers and onboard default settings.

Note:

How to setup Jumpers

That a cap on a jumper is to “close” the jumper, whereas that offs a jumper is to “open” the
jumper.

[Open] [Closed] [Pin1-2 Closed]

Jumper

Descriptions

Setting

JP1

Clear RTC : Normal

Short 1-2

1.6.1 Restore BIOS Optimal Defaults (JP1)

Put jumper clip to pin 2-3 for a few seconds then move it back to pin 1-2. Doing this procedure
can restore BIOS optimal defaults.

Function

Setting

Normal operation (Default)

1-2 close

Restore BIOS optimal defaults

2-3 close

IPC962-511-FL/IPC964-512-FL Series User’s Manual

Introduction

10

1.7 Connectors

Connectors connect this board with other parts of the system. Loose or improper connection
might cause problems. Make sure all connectors are properly and firmly connected.

Here is a summary table shows you all connectors on the board.

Connector

Label

MINI CARD SLOT

CN3

LAN1+USB3.0

CN4

LAN2+USB3.0

CN5

VGA Connector

CN6

Audio Connector

CN7

DC-in Phoenix Power Connector

CN8

HDMI Connector

CN9

SATA Power connector

SCN1、SCN2

SATA III connector

SATA1~2

DDR4 SO-DIMM(260 Pin)

SDIMM1、 SDIMM2

Power botton

SW1

AT/ATX Power Selet

SW2

Reset botton

SW3

Remote SW

PWRBT1

Flexible IO- COM x4(RS232/422/485)

AX93511

Riser Card Power output

ATX1,ATX2

IPC962-511-FL/IPC964-512-FL Series User’s Manual

Introduction

11

1.7.1 MINI CARD SLOT (CN3)

There is a PCI-Express Mini Card connector on the top side applying USB 2.0. It supports an
USB mini card.

Pins

Signals

Pins

Signals

1

WAKE#

2

+3.3VSB

3

No use

4

GND

5

No use

6

+1.5V

7

CLKREQ#

8

No use

9

GND

10

No use

11

REFCLK-

12

No use

13

REFCLK+

14

No use

15

GND

16

No use

17

No use

18

GND

19

No use

20

W_DISABLE#

21

GND

22

PERST#

23

PE_RXN3/

24

+3.3VSB

25

PE_RXP3/

26

GND

27

GND

28

+1.5V

29

GND

30

SMB_CLK

31

PE_TXN3/

32

SMB_DATA

33

PE_TXP3/

34

GND

35

GND

36

USB_D8-

37

GND

38

USB_D8+

39

+3.3VSB

40

GND

41

+3.3VSB

42

No use

43

GND

44

No use

45

No use

46

No use

47

No use

48

+1.5V

49

No use

50

GND

51

No use

52

+3.3VSB