AXIOMTEK IFO2225-830 User Manual
IFO2225-830 Series
All-In-One 22” Super Slim & Fanless
Panel Computer
User’s Manual
Disclaimers
This manual has been carefully checked and believed to contain
accurate information. AXIOMTEK Co., Ltd. assumes no responsibility
for any infringements of patents or any third party’s rights, and any
liability arising from such use.
AXIOMTEK does not warrant or assume any legal liability or
responsibility for the accuracy, completeness or usefulness of any
information in this document. AXIOMTEK does not make any
commitment to update the information in this manual.
AXIOMTEK reserves the right to change or revise this document
and/or product at any time without notice.
No part of this document may be reproduced, stored in a retrieval
system, or transmitted, in any form or by any means, electronic,
mechanical, photocopying, recording, or otherwise, without the prior
written permission of AXIOMTEK Co., Ltd.
©Copyright 2010 AXIOMTEK Co., Ltd.
All Rights Reserved
March 2010, Version A1
Printed in Taiwan
ii
Safety Approvals
CE Marking
FCC Class A
FCC Compliance
This equipment has been tested in compliance with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are meant to provide reasonable protection against harmful
interference in a residential installation. If not installed and used in
accordance with proper instructions, this equipment might generate or
radiate radio frequency energy and cause harmful interference to
radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following methods:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment to another outlet of a circuit that
doesn’t connect with the receiver.
4. Consult the dealer or an experienced radio/TV technician for
help.
Shielded interface cables must be used in order to comply with the
emission limits.
iii
Safety Precautions
Before getting started, read the following important safety precautions.
1. The IFO2225-830 Series does not come equipped with an
operating system. An operating system must be loaded first
before installing any software into the computer.
2. Be sure to ground yourself to prevent static charge when
installing the internal components. Use a grounding wrist
strap and place all electronic components in any staticshielded devices. Most electronic components are sensitive
to static electrical charge.
3. Disconnect the power cord from the IFO2225-830 Series
before any installation. Be sure both the system and external
devices are turned OFF. A sudden surge of power could ruin
sensitive components that the IFO2225-830 Series must be
properly grounded.
4. Make sure it is the correct voltage of the power source
before connecting the equipment to the power outlet.
5. The brightness of the flat panel display will be getting weaker
as a result of frequent usage. However, the operating period
varies depending on the application environment.
6. Turn OFF the system power before cleaning. Clean the
system using a cloth only. Do not spray any liquid cleaner
directly onto the screen. The IFO2225-830 Series may come
with or w/o a touchscreen. Although the touchscreen is
chemical resistant, it is recommended that you spray the
liquid cleaner on a cloth first before wiping the screen. In
case your system comes without the touchscreen, you must
follow the same procedure and not spray any cleaner on the
flat panel directly.
7. Avoid using sharp objects to operate the touchscreen.
Scratches on the touchscreen may cause malfunction or
internal failure to the touchscreen.
8. The flat panel display is not susceptible to shock or vibration.
When assembling the IFO2225-830 Series, make sure it is
securely installed.
9. Do not leave this equipment in an uncontrolled environment
where the storage temperature is below -20℃ or above 60℃.
It may damage the equipment.
10. External equipment intended for connection to signal
iv
input/out or other connectors shall comply with relevant
UL/IEC standard.
11. Do not open the system’s back cover. If opening the cover
for maintenance is a must, only a trained technician is
allowed to do so. Integrated circuits on computer boards are
sensitive to static electricity. To avoid damaging chips from
electrostatic discharge, observe the following precautions:
z Before handling a board or integrated circuit, touch an
unpainted portion of the system unit chassis for a few
seconds. This will help to discharge any static
electricity on your body.
z When handling boards and components, wear a wrist-
grounding strap, available from most electronic
component stores.
Classification
1. Degree of production against electric shock: not classified
2. Degree of protection against the ingress of water: IPX1
3. Equipment not suitable for use in the presence of a
flammable anesthetic mixture with air or with oxygen or
nitrous oxide.
4. Mode of operation: Continuous
5. Type of protection against electric shock: Class I equipment
v
General Cleaning Tips
You may need the following precautions before you begin to clean the
computer. When you clean any single part or component for the
computer, please read and understand the details below fully.
1. When you need to clean the device, please rub it with a
piece of dry cloth.
2. Be cautious of the tiny removable components when you
use a vacuum cleaner to absorb the dirt on the floor.
3. Turn the system off before you start to clean up the
component or computer.
4. Never drop the components inside the computer or get
circuit board damp or wet.
5. Be cautious of all kinds of cleaning solvents or chemicals
when you use it for the sake of cleaning. Some individuals
may be allergic to the ingredients.
6. Try not to put any food, drink or cigarette around the
computer.
Cleaning Tools:
Although many companies have created products to help improve the
process of cleaning your computer and peripherals users can also
use household items to clean their computers and peripherals. Below
is a listing of items you may need or want to use while cleaning your
computer or computer peripherals.
Keep in mind that some components in your computer may only be
able to be cleaned using a product designed for cleaning that
component, if this is the case it will be mentioned in the cleaning.
z Cloth: A piece of cloth is the best tool to use when rubbing
up a component. Although paper towels or tissues can be
used on most hardware as well, we still recommend you to
rub it with a piece of cloth.
z Water or rubbing alcohol: You may moisten a piece of cloth
a bit with some water or rubbing alcohol and rub it on the
computer. Unknown solvents may be harmful to the plastics
parts.
z Vacuum cleaner: Absorb the dust, dirt, hair, cigarette
particles, and other particles out of a computer can be one
of the best methods of cleaning a computer. Over time
these items can restrict the airflow in a computer and cause
circuitry to corrode.
vi
z Cotton swabs: Cotton swaps moistened with rubbing alcohol
or water are excellent tools for wiping hard to reach areas in
your keyboard, mouse, and other locations.
z Foam swabs: Whenever possible it is better to use lint free
swabs such as foam swabs.
Note We strongly recommended that you should shut down
the system before you start to clean any single
components.
Please follow the steps below:
1. Close all application programs
2. Close operating software
3. Turn off power switch
4. Remove all device
5. Pull out power cable
vii
Scrap Computer Recycling
If the computer equipments need the maintenance or are beyond
repair, we strongly recommended that you should inform your
Axiomtek distributor as soon as possible for the suitable solution. For
the computers that are no longer useful or no longer work well, please
contact your Axiomtek distributor for recycling and we will make the
proper arrangement.
Trademarks Acknowledgments
AXIOMTEK is a trademark of AXIOMTEK Co., Ltd.
IBM, PC/AT, PS/2, VGA are trademarks of International
Business Machines Corporation.
®
and Pentium® are registered trademarks of Intel Corporation.
Intel
MS-DOS, Microsoft C and QuickBASIC are trademarks of Microsoft
Corporation.
VIA is a trademark of VIA Technologies, Inc.
SST is a trademark of Silicon Storage Technology, Inc.
UMC is a trademark of United Microelectronics Corporation.
Other brand names and trademarks are the properties and registered
brands of their respective owners.
viii
Table of Contents
Disclaimers..........................................................................ii
Safety Approvals.................................................................iii
Safety Precautions..............................................................iv
Classification ...................................................................... v
General Cleaning Tips........................................................vi
Scrap Computer Recycling...............................................viii
CHAPTER 1 INTRODUCTION .......................................1
1.1 General Description............................................ 1
1.2 Features..............................................................2
1.3 System Specifications.........................................2
1.4 Dimensions......................................................... 5
1.5 I/O Outlets...........................................................6
1.6 Packing List ........................................................8
CHAPTER 2 HARDWARE INSTALLATION..................10
2.1 DRAM Installation............................................. 10
2.2 Hard Disk Drive Installation ..............................14
2.3 CF Card Installation.......................................... 18
2.4 Serial Ports Interface........................................22
2.5 Wireless Module Installation (Optional)............24
2.6 Mountings (Optional) ........................................28
2.6.1 Wallmount (Optional)................................................ 28
2.6.2 VESA Mount (Optional) ............................................ 29
2.6.3 Desktop Stand (Optional) ......................................... 30
CHAPTER 3 AMI BIOS SETUP UTILITY......................34
3.1 Starting .............................................................34
3.2 Navigation Keys................................................34
3.3 Main Menu........................................................ 35
3.4 Advanced Menu................................................36
3.5 PCI PnP Menu.................................................. 49
3.6 Boot Menu ........................................................52
3.7 Security Menu...................................................57
3.8 Chipset Menu....................................................59
ix
3.9 Exit Menu..........................................................64
CHAPTER 4 DRIVER INSTALLATION.........................66
4.1 System..............................................................66
4.2 Touch Screen ...................................................67
4.2.1 Specification..............................................................67
4.2.2 Driver Installation ...................................................... 68
x
MEMO
xi
IFO2225-830 Series Panel PC User’s Manual
CHAPTER 1
INTRODUCTION
This chapter contains general information and detailed specifications
of the IFO2225-830 Series. Chapter 1 includes the following sections:
General Description
Features
System Specification
Dimensions
I/O Outlets
Package List
1.1 General Description
The IFO2225-830 is an ultra slim panel computer equipped with 22inch 300nits high brightness WSXGA+ LCD display and supports
superior Intel
Powered by Intel
computer has better graphic performance. The panel also supports
Dual View and multiple I/O options including 4 USB 2.0, 4 RS-232
ports. Furthermore, the IFO2225-830 supports antenna for wireless
(802.11 b/g) expansion. The IFO2225-830 is designed to work with
low noise, low power consumption, high reliability and high
performance applications. Besides, excellent ID (industrial design)
and user friendly interface design make the IFO2225-830 perfect with
super slim, professional outlook, better user interface, and excellent
protection at once! This safe, reliable & user-friendly panel computer
can ensure customer’s project success and best suited for
PIO/POS/kiosk, media content display, and HMI solutions.
○R
AtomTM N270 1.6GHz processor with FSB 533MHz.
®
945GSE +ICH7M core logic chipset, this panel
Introduction
1
IFO2225-830 Series Panel PC User’s Manual
1.2 Features
¾ 22” high brightness ( 300nits) WSXGA+ TFT LCD
¾ Intel
○R
AtomTM N270 1.6GHz processor with FSB 533MHz
onboard
¾ NEMA 4/12 (IP65) - compliant front bezel
¾ IPx1 – whole enclosure
¾ Fanless and noiseless operation
¾ Optional 1.3 mega pixels camera
¾ Optional wireless (802.11 b/g) antenna
1.3 System Specifications
FRONT BEZEL
LCD PANEL
PLASTIC ABS
DISPLAY TYPE 22” WSXGA+ TFT
BRIGHTNESS
(cd/m²)
300 nits
RESOLUTION 1680 x 1050
VIEWING ANGLE
(H/V)
178º/178º
2
Introduction
MAIN SYSTEM
I/O
CONNECTORS
CAMERA
TOUCHSCREEN
POWER SUPPLY
DIMENSIONS
WEIGHT
IFO2225-830 Series Panel PC User’s Manual
○R
AtomTM N270 1.6GHz
CPU
CHIPSET
SYSTEM
MEMORY
Intel
processor with FSB 533MHz
®
INTEL
945GSE+ICH7M
SUPPORTS 1 DDR2
SODIMM MEMORY UP TO 2
GB
1 x 2.5" SATA HDD DRIVE
STORAGE
BAY
1 x CompactFlash
OPTICAL DRIVE OPTIONAL COMBO DRIVER
1 x RS-232/RS-422/RS-485 (COM 1)
3 x RS-232
4 x USB 2.0
1 x AUDIO (LINE-OUT)
1 x VGA
2 x 10/100/1000Mbps ETHERNET
1 x 12V DC-IN POWER CONNECTOR
1 x 1.3 MEGA PIXELS CAMERA (option)
RESISTIVE TYPE
LIGHT TRANSMISSION: 80%
TOUCH LIFETIME: 35 MILLION TOUCHES
12V AC-DC ADAPTOR
574mm (22.58") (W) x 69mm (2.69") (D) x
399mm (15.71") (H)
8.22kg (18.12 lb)
Introduction
3
IFO2225-830 Series Panel PC User’s Manual
OPERATION TEMPERATURE: 0ºC~40ºC
(32ºF~104ºF)
ENVIRONMENTA
L
RELATIVE HUMIDITY: 10%~95%, NONCONDESING
SHOCK: 10G PEAK ACCELERATION (11 SEC.
DURATION)
CERTIFICATION
CE
NOTE All specifications and images are subject to change
without notice.
4
Introduction
IFO2225-830 Series Panel PC User’s Manual
1.4 Dimensions
The following diagrams show you dimensions and outlines of the
IFO2225-830 Series.
Introduction
5
IFO2225-830 Series Panel PC User’s Manual
1.5 I/O Outlets
The following figures show you the locations of the IFO2225-830
Series I/O outlets.
○1 ○3 ○2
6
Introduction
¾ I/O Outlets
IFO2225-830 Series Panel PC User’s Manual
○4
○6 ○5
○7
○8
○9 ○10 ○
11 ○12 ○13
NO CONNECTOR
1 BRIGHTNESS ADJUST BUTTONS
2 VOLUME ADJUST BUTTONS
3 POWER LED
4 DC-IN POWER CONNECTOR
5 COM 1 (RS-232/422/485)
6 COM 2 (RS-232)
7 VGA
8 ETHERNET
9 USB 2.0 x 2
10 AUDIO (LINE-OUT)
11 USB 2.0 x 2
12 COM 3 (RS-232)
13 COM 4 (RS-232)
Introduction
7
IFO2225-830 Series Panel PC User’s Manual
1.6 Packing List
The package bundled with your IFO2225-830 should contain the
following items:
z IFO2225-830 Series Unit x 1
z 12V AC-DC Power Adaptor
z Power Cord x 1
z CD x 1 (For Driver and User’s Manual)
z combo Cover x 2 (For within combo type)
z SATA cable x 1
z Cable Management Kit x 2
z Wall-Mount Bracket x 1
z M4 x 8 Screws x 4 (for VESA Mounting)
z M3 x 5 Screws x 2 (for Cable Management Kit)
If you can not find this package or any items are missing, please
contact AXIOMTEK distributors immediately.
8
Introduction
MEMO
IFO2225-830 Series Panel PC User’s Manual
Introduction
9
IFO2225-830 Series Panel PC User’s Manual
CHAPTER 2
HARDWARE INSTALLATION
The IFO2225-830 Series are convenient for your various hardware
configurations, such as CPU (Central Processing Unit) and HDD (Hard
Disk Drive). The chapter 2 will show you how to install the hardware. It
includes:
2.1 DRAM Installation
The IFO2225-830 provides one 200-pin DDR2 SODIMM sockets
that support system memory up to 2GB. Please follow steps below
to install the memory modules:
Step 1 Turn off the system, and unplug the Power cord.
Step 2 Locate and release these screws to open the back cover
10
Hardware Installation
IFO2225-830 Series Panel PC User’s Manual
Step 3 Please open the back cover by lifting the joint part as marked.
Step 4 Open the back cover and find mainboard
Hardware Installation
11
IFO2225-830 Series Panel PC User’s Manual
Step 5 Push down latches on each side of the DIMM socket.
Step 6 Install the memory module into the socket and push it firmly
down until it is fully seated. The socket latches are levered upwards
and clipped on to the edges of the DIMM.
12
Hardware Installation
IFO2225-830 Series Panel PC User’s Manual
Step 7 Close the back cover to the chassis, and fasten all screws.
Hardware Installation
13
Loading...