IFO2175-830 Series
All-In-One 17” Super Slim & Fanless
Panel Computer
User’s Manual
Disclaimers
This manual has been carefully checked and believed to contain
accurate information. AXIOMTEK Co., Ltd. assumes no responsibility
for any infringements of patents or any third party’s rights, and any
liability arising from such use.
AXIOMTEK does not warrant or assume any legal liability or
responsibility for the accuracy, completeness or usefulness of any
information in this document. AXIOMTEK does not make any
commitment to update the information in this manual.
AXIOMTEK reserves the right to change or revise this document
and/or product at any time without notice.
No part of this document may be reproduced, stored in a retrieval
system, or transmitted, in any form or by any means, electronic,
mechanical, photocopying, recording, or otherwise, without the prior
written permission of AXIOMTEK Co., Ltd.
©Copyright 2010 AXIOMTEK Co., Ltd.
All Rights Reserved
May 2010, Version A2
Printed in Taiwan
ii
Safety Approvals
CE Marking
FCC Class A
FCC Compliance
This equipment has been tested in compliance with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are meant to provide reasonable protection against harmful
interference in a residential installation. If not installed and used in
accordance with proper instructions, this equipment might generate or
radiate radio frequency energy and cause harmful interference to
radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following methods:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment to another outlet of a circuit that
doesn’t connect with the receiver.
4. Consult the dealer or an experienced radio/TV technician for
help.
Shielded interface cables must be used in order to comply with the
emission limits.
iii
Safety Precautions
Before getting started, read the following important safety precautions.
1. The IFO2175-830 Series does not come equipped with an
operating system. An operating system must be loaded first
before installing any software into the computer.
2. Be sure to ground yourself to prevent static charge when
installing the internal components. Use a grounding wrist
strap and place all electronic components in any staticshielded devices. Most electronic components are sensitive
to static electrical charge.
3. Disconnect the power cord from the IFO2175-830 Series
before any installation. Be sure both the system and external
devices are turned OFF. A sudden surge of power could ruin
sensitive components that the IFO2175-830 Series must be
properly grounded.
4. Make sure it is the correct voltage of the power source
before connecting the equipment to the power outlet.
5. The brightness of the flat panel display will be getting weaker
as a result of frequent usage. However, the operating period
varies depending on the application environment.
6. Turn OFF the system power before cleaning. Clean the
system using a cloth only. Do not spray any liquid cleaner
directly onto the screen. The IFO2175-830 Series may come
with or w/o a touchscreen. Although the touchscreen is
chemical resistant, it is recommended that you spray the
liquid cleaner on a cloth first before wiping the screen. In
case your system comes without the touchscreen, you must
follow the same procedure and not spray any cleaner on the
flat panel directly.
7. Avoid using sharp objects to operate the touchscreen.
Scratches on the touchscreen may cause malfunction or
internal failure to the touchscreen.
8. The flat panel display is not susceptible to shock or vibration.
When assembling the IFO2175-830 Series, make sure it is
securely installed.
9. Do not leave this equipment in an uncontrolled environment
where the storage temperature is below -20℃ or above 60℃.
It may damage the equipment.
10. External equipment intended for connection to signal
iv
input/out or other connectors shall comply with relevant
UL/IEC standard.
11. Do not open the system’s back cover. If opening the cover
for maintenance is a must, only a trained technician is
allowed to do so. Integrated circuits on computer boards are
sensitive to static electricity. To avoid damaging chips from
electrostatic discharge, observe the following precautions:
z Before handling a board or integrated circuit, touch an
unpainted portion of the system unit chassis for a few
seconds. This will help to discharge any static
electricity on your body.
z When handling boards and components, wear a wrist-
grounding strap, available from most electronic
component stores.
Classification
1. Degree of production against electric shock: not classified
2. Degree of protection against the ingress of water: IPX1
3. Equipment not suitable for use in the presence of a
flammable anesthetic mixture with air or with oxygen or
nitrous oxide.
4. Mode of operation: Continuous
5. Type of protection against electric shock: Class I equipment
v
General Cleaning Tips
You may need the following precautions before you begin to clean the
computer. When you clean any single part or component for the
computer, please read and understand the details below fully.
1. When you need to clean the device, please rub it with a
piece of dry cloth.
2. Be cautious of the tiny removable components when you
use a vacuum cleaner to absorb the dirt on the floor.
3. Turn the system off before you start to clean up the
component or computer.
4. Never drop the components inside the computer or get
circuit board damp or wet.
5. Be cautious of all kinds of cleaning solvents or chemicals
when you use it for the sake of cleaning. Some individuals
may be allergic to the ingredients.
6. Try not to put any food, drink or cigarette around the
computer.
Cleaning Tools:
Although many companies have created products to help improve the
process of cleaning your computer and peripherals users can also
use household items to clean their computers and peripherals. Below
is a listing of items you may need or want to use while cleaning your
computer or computer peripherals.
Keep in mind that some components in your computer may only be
able to be cleaned using a product designed for cleaning that
component, if this is the case it will be mentioned in the cleaning.
z Cloth: A piece of cloth is the best tool to use when rubbing
up a component. Although paper towels or tissues can be
used on most hardware as well, we still recommend you to
rub it with a piece of cloth.
z Water or rubbing alcohol: You may moisten a piece of cloth
a bit with some water or rubbing alcohol and rub it on the
computer. Unknown solvents may be harmful to the plastics
parts.
z Vacuum cleaner: Absorb the dust, dirt, hair, cigarette
particles, and other particles out of a computer can be one
of the best methods of cleaning a computer. Over time
these items can restrict the airflow in a computer and cause
circuitry to corrode.
vi
z Cotton swabs: Cotton swaps moistened with rubbing alcohol
or water are excellent tools for wiping hard to reach areas in
your keyboard, mouse, and other locations.
z Foam swabs: Whenever possible it is better to use lint free
swabs such as foam swabs.
Note We strongly recommended that you should shut down
the system before you start to clean any single
components.
Please follow the steps below:
1. Close all application programs
2. Close operating software
3. Turn off power switch
4. Remove all device
5. Pull out power cable
vii
Scrap Computer Recycling
If the computer equipments need the maintenance or are beyond
repair, we strongly recommended that you should inform your
Axiomtek distributor as soon as possible for the suitable solution. For
the computers that are no longer useful or no longer work well, please
contact your Axiomtek distributor for recycling and we will make the
proper arrangement.
Trademarks Acknowledgments
AXIOMTEK is a trademark of AXIOMTEK Co., Ltd.
IBM, PC/AT, PS/2, VGA are trademarks of International
Business Machines Corporation.
®
and Pentium® are registered trademarks of Intel Corporation.
Intel
MS-DOS, Microsoft C and QuickBASIC are trademarks of Microsoft
Corporation.
VIA is a trademark of VIA Technologies, Inc.
SST is a trademark of Silicon Storage Technology, Inc.
UMC is a trademark of United Microelectronics Corporation.
Other brand names and trademarks are the properties and registered
brands of their respective owners.
viii
Table of Contents
Disclaimers....................................................................................ii
Safety Approvals ..........................................................................iii
Safety Precautions .......................................................................iv
Classification .................................................................................v
General Cleaning Tips..................................................................vi
Scrap Computer Recycling......................................................... viii
CHAPTER 1 INTRODUCTION.......................................................... 1
1.1 General Description.................................................... 1
1.2 Features...................................................................... 2
1.3 System Specifications................................................. 2
1.4 Dimensions................................................................. 5
1.5 I/O Outlets................................................................... 6
1.6 Packing List................................................................. 8
1.7 Power Switch.............................錯誤! 尚未定義書籤。
CHAPTER 2 HARDWARE INSTALLATION.................................. 10
2.1 DRAM Installation.....................................................10
2.2 Hard Disk Drive Installation ...................................... 13
2.3 CF Card Installation..................................................17
2.4 Serial Ports Interface ................................................ 21
2.5 Wireless Module Installation (Optional).................... 23
2.6 Mountings (Optional) ................................................ 27
2.6.1 Wallmount (Optional)................................................ 27
2.6.2 VESA Mount (Optional) ............................................ 28
2.6.3 Desktop Stand (Optional) ......................................... 29
CHAPTER 3 AMI BIOS SETUP UTILITY.......................................33
3.1 Starting...................................................................... 33
3.2 Navigation Keys........................................................ 33
3.3 Main Menu................................................................ 34
3.4 Advanced Menu........................................................ 35
3.5 PCI PnP Menu.......................................................... 48
3.6 Boot Menu................................................................. 51
3.7 Security Menu........................................................... 56
3.8 Chipset Menu............................................................58
3.9 Exit Menu.................................................................. 63
ix
CHAPTER 4 DRIVER INSTALLATION.......................................... 65
4.1 System...................................................................... 65
4.2 Touch Screen............................................................ 66
4.2.1 Specification.............................................................. 66
4.2.2 Driver Installation......................................................67
x
MEMO
xi
IFO2175-830 Series Panel PC User’s Manual
CHAPTER 1
INTRODUCTION
This chapter contains general information and detailed specifications
of the IFO2175-830 Series. Chapter 1 includes the following sections:
General Description
Features
System Specification
Dimensions
I/O Outlets
Package List
1.1 General Description
The IFO2175-830 is an ultra slim panel computer equipped with 17inch 300nits high brightness SXGA LCD display and supports
superior Intel
Powered by Intel
computer has better graphic performance. The panel also supports
Dual View and multiple I/O options including 4 USB 2.0, 4 RS-232
ports. Furthermore, the IFO2175-830 supports antenna for wireless
(802.11 b/g) expansion. The IFO2175-830 is designed to work with
low noise, low power consumption, high reliability and high
performance applications. Besides, excellent ID (industrial design)
and user friendly interface design make the IFO2175-830 perfect with
super slim, professional outlook, better user interface, and excellent
protection at once! This safe, reliable & user-friendly panel computer
can ensure customer’s project success and best suited for
PIO/POS/kiosk, media content display, and HMI solutions.
○R
AtomTM N270 1.6GHz processor with FSB 533MHz.
®
945GSE +ICH7M core logic chipset, this panel
Introduction
1
IFO2175-830 Series Panel PC User’s Manual
1.2 Features
¾ 17” high brightness ( 380nits) SXGA TFT LCD
¾ Intel
○R
AtomTM N270 1.6GHz processor with FSB 533MHz
onboard
¾ NEMA 4/12 (IP65) - compliant front bezel
¾ IPx1 – whole enclosure
¾ Fanless and noiseless operation
¾ Optional 1.3 mega pixels camera
¾ Optional wireless (802.11 b/g) antenna
1.3 System Specifications
FRONT BEZEL
LCD PANEL
PLASTIC ABS
DISPLAY TYPE 17" SXGA TFT
BRIGHTNESS
(cd/m²)
380 nits
RESOLUTION 1280 x 1024
VIEWING ANGLE
(H/V)
160º/160º
2
Introduction
MAIN SYSTEM
I/O
CONNECTORS
CAMERA
TOUCHSCREEN
POWER SUPPLY
DIMENSIONS
WEIGHT
IFO2175-830 Series Panel PC User’s Manual
○R
AtomTM N270 1.6GHz
CPU
CHIPSET
SYSTEM
MEMORY
STORAGE
OPTICAL DRIVE
Intel
processor with FSB 533MHz
®
INTEL
945GSE+ICH7M
SUPPORTS 1 DDR2
SODIMM MEMORY UP TO
2 GB
1 x 2.5" SATA HDD DRIVE
BAY
OPTIONAL 1 COMPACT
COMBO DRIVE
1 x RS-232/RS-422/RS-485 (COM 1)
3 x RS-232
4 x USB 2.0
1 x PS/2 MOUSE AND KEYBOARD
1 x AUDIO (MIC-IN/LINE-OUT)
1 x VGA
2 x 10/100/1000Mbps ETHERNET
1 x 12V DC-IN POWER CONNECTOR
1 x 1.3 MEGA PIXELS CAMERA (option)
RESISTIVE TYPE
LIGHT TRANSMISSION: 80%
TOUCH LIFETIME: 35 MILLION TOUCHES
12VDC, w/ AC-DC POWER ADAPTOR
437.98mm (17.24") (W) x 76.5mm (3.01") (D) x
376.41mm (14.81") (H)
7.65kg (16.85 lb)
Introduction
3
IFO2175-830 Series Panel PC User’s Manual
OPERATION TEMPERATURE: 0ºC~40ºC
(32ºF~104ºF)
ENVIRONMENTA
L
RELATIVE HUMIDITY: 10%~95%, NONCONDESING
SHOCK: 10G PEAK ACCELERATION (11 SEC.
DURATION)
CERTIFICATION
CE
NOTE All specifications and images are subject to change
without notice.
NOTE If it is operated in high temperature environment, the
wide temperature DRAM and HDD are recommended.
4
Introduction
IFO2175-830 Series Panel PC User’s Manual
1.4 Dimensions
The following diagrams show you dimensions and outlines of the
IFO2175-830 Series.
Introduction
5
IFO2175-830 Series Panel PC User’s Manual
1.5 I/O Outlets
The following figures show you the locations of the IFO2175-830
Series I/O outlets.
○1
6
○2
○3
○4
Introduction
¾ I/O Outlets
IFO2175-830 Series Panel PC User’s Manual
NO CONNECTOR
1 BRIGHTNESS ADJUST BUTTONS
2 VOLUME ADJUST BUTTONS
3 POWER LED
4 POWER SWITCH
5 DC-IN POWER CONNECTOR
6 COM 1 (RS-232/422/485)
7 COM 2 (RS-232)
8 VGA
9 ETHERNET
10 USB 2.0 x 2
11 AUDIO (LINE-OUT)
12 USB 2.0 x 2
13 COM 3 (RS-232)
14 COM 4 (RS-232)
Introduction
7
IFO2175-830 Series Panel PC User’s Manual
1.6 Packing List
The package bundled with your IFO2175-830 should contain the
following items:
z IFO2175-830 Series Unit x 1
z 12VDC, w/ AC-DC Power Adaptor
z Power Cord x 1
z CD x 1 (For Driver and User’s Manual)
z DVD-combo Cover x 2 (For within DVD-combo) (option)
z SATA cable x 1
z Cable Management Kit x 2
z Fuse x 1
z Wall-Mount Bracket x 1
z M4 x 8 Screws x 4 (for VESA Mounting)
z M3 x 5 Screws x 2 (for Cable Management Kit)
If you can not find this package or any items are missing, please
contact AXIOMTEK distributors immediately.
8
Introduction
MEMO
IFO2175-830 Series Panel PC User’s Manual
Introduction
9
IFO2175-830 Series Panel PC User’s Manual
CHAPTER 2
HARDWARE INSTALLATION
The IFO2175-830 Series are convenient for your various hardware
configurations, such as CPU (Central Processing Unit) and HDD (Hard
Disk Drive). The chapter 2 will show you how to install the hardware. It
includes:
2.1 DRAM Installation
The IFO2175-830 provides one 200-pin DDR2 SODIMM sockets
that support system memory up to 2GB. Please follow steps below
to install the memory modules:
Step 1 Turn off the system, and unplug the Power cord.
Step 2 Locate and release these screws to open the back cover
10
Hardware Installation
IFO2175-830 Series Panel PC User’s Manual
Step 3 Please open the back cover by lifting the joint part as marked.
Step 4 Open the back cover and find mainboard
Hardware Installation
11
IFO2175-830 Series Panel PC User’s Manual
Step 5 Push down latches on each side of the DIMM socket.
Step 6 Install the memory module into the socket and push it firmly
down until it is fully seated. The socket latches are levered upwards
and clipped on to the edges of the DIMM.
12
Hardware Installation
IFO2175-830 Series Panel PC User’s Manual
2.2 Hard Disk Drive Installation
The IFO2175-830 Series offers a convenient drive bay module for
users to install HDD. The system offers users one 2.5” Hard Disk Drive
for installation. Please follow the steps:
Step 1 Turn off the system, and unplug the Power cord.
Step 2 Locate and release these screws to open the back cover.
Hardware Installation
13
IFO2175-830 Series Panel PC User’s Manual
Step 3 Please open the back cover by lifting the joint part as marked.
Step 4 Locate the HDD socket as marked.
14
Hardware Installation
IFO2175-830 Series Panel PC User’s Manual
Step 5 Use assembly parts to fix HDD with the bracket.
1. HDD Bracket x1
2. 2.5 inch Hard-disk
3. Screw x 4
4. Assembly the HDD with the bracket.
ATTENTION Please follow the direction of Hard-disk installation.
“Hard-disk PCB facesup”.
Hardware Installation
15
IFO2175-830 Series Panel PC User’s Manual
Step 6 Install the HDD bracket inside the system. Plug the SATA and
Power cables in HDD.
Data Power
Step 7 Close the back cover to the chassis, and fasten all screws.
16
Hardware Installation
IFO2175-830 Series Panel PC User’s Manual
2.3 CF Card Installation
The IFO2175-830 series provides one CF slot for users to install
CompactFlash
installation:
Step 1 Turn off the system, and unplug the Power cord.
Step 2 Locate and release these screws to open the back cover.
™ card. Please refer to the following instructions for
Hardware Installation
17
IFO2175-830 Series Panel PC User’s Manual
Step 3 Please open the back cover by lifting the joint part as marked.
Step 4 Unplug the CD-ROM Power cord, if IFO2175-830 is with CD-
ROM version.
18
Hardware Installation
IFO2175-830 Series Panel PC User’s Manual
Step 5 Locate the CompactFlash
the socket.
TM
socket, and insert the card into
Hardware Installation
19
IFO2175-830 Series Panel PC User’s Manual
Step 6 Plug the CD-ROM Power cord, if IFO2175-830 is with CDROM version.
Step 7 Close the back cover to the chassis, and fasten all screws.
20
Hardware Installation
IFO2175-830 Series Panel PC User’s Manual
2.4 Serial Ports Interface
The IFO2175-830 series has two onboard serial ports, COM1 (RS232/ 422/ 485) and COM2 (RS-232).
The following table shows you the pin assignments of this connector:
Pin Signal Pin Signal
1 Data Carrier Detect (DCD) 6 Data Set Ready (DSR)
2 Receive Data (RXD) 7 Request To Send (RTS)
3 Transmit Data (T XD) 8 Clear To Send (CTS)
4 Data Terminal Ready (DTR) 9 Ring Indicator (RI)
5 Ground (GND)
In addition, COM1 can be set for RS-232/422/485 by jumper. The jump
setting is listed as below:
COM1 JP11 JP12 JP13
RS-232 (default) 3-5, 4-6 3-5, 4-6 1-2
RS-422 1-3, 2-4 1-3, 2-4 3-4, 7-8
RS-485 1-3, 2-4 1-3, 2-4 5-6, 7-8
Hardware Installation
21
IFO2175-830 Series Panel PC User’s Manual
When COM1 is set to RS-422 or RS-485, the pin assignments are
listed below:
Pin #
1 TX- DATA2 TX+ DATA+
3 RX+ No connector
4 RX- No connector
5 No connector No connector
6 No connector No connector
7 No connector No connector
8 No connector No connector
9 GND GND
RS-422 RS-485
Signal Name
22
Hardware Installation
IFO2175-830 Series Panel PC User’s Manual
2.5 Wireless Module Installation (Optional)
You can follow the steps below to install an optional wireless module.
Step 1 Turn off the system, and unplug the Power cord.
Step 2 Locate and release these screws to open the back cover.
Hardware Installation
23
IFO2175-830 Series Panel PC User’s Manual
Step 3 Please open the back cover by lifting the joint part as marked.
Step 4 Open the back cover and find mainboard (SBC87830).
24
Hardware Installation
IFO2175-830 Series Panel PC User’s Manual
Step 5 The socket latches are clipped on to the edges of the Mini
card. Install wireless LAN card to the socket.
○1
○2
Step 6 There are two choices of antennas which are installed in
IFO2175-830 series. One is build-in antennas. The other is external
antennas. Please follow the steps:
Hardware Installation
25
IFO2175-830 Series Panel PC User’s Manual
Step 7 Find the built-in Antenna cable which is tied with other
cables on the bottom of the device. There are two connectors on
wireless LAN card. One is MAIN, and the other is AUX. Connect
antenna cable to MAIN connector on wireless LAN card.
Step 8 Close the back cover to the chassis, and fasten all screws.
26
Hardware Installation
IFO2175-830 Series Panel PC User’s Manual
2.6 Mountings (Optional)
There are several mounting ways for the IFO2175-830 Series,
Wallmount, VESA and Desktop mountings as below:
2.6.1 Wallmount (Optional)
The mounting for IFO2175-830 Series is Wallmount as below:
Step 1 Prepare all parts for installing the wallmount kit.
Step 2 Assemble the mallmount kit by using screws to fix the
backplane.
1
○
○
2
Hardware Installation
27
IFO2175-830 Series Panel PC User’s Manual
2.6.2 VESA Mount (Optional)
The mounting for IFO2175-830 Series is VESA-Arm as below:
Assemble the VESA-Arm by using screws to fix the backplane.
28
Hardware Installation
IFO2175-830 Series Panel PC User’s Manual
2.6.3 Desktop Stand (Optional)
The IFO2175-830 Series provides you with an optional Desktop
Stand that you can follow the steps below:
Step 1 Prepare the parts of desktop stand.
Screw A Screw B
Screw C Hinge Cover
Hardware Installation
29
IFO2175-830 Series Panel PC User’s Manual
Step 2 Assemble the desktop stand. Fix the screws as marked on
the bottom side of chassis. (Use Screw A)
Step 3 Fix the screws as marked on the back side of chassis (Use
Screw B).
30
Hardware Installation
IFO2175-830 Series Panel PC User’s Manual
Step 3 Fix the desktop stand firmly.
Rear View
Front View
Hardware Installation
31
IFO2175-830 Series Panel PC User’s Manual
MEMO
32
Hardware Installation
IFO2175-830 Series Panel PC User’s Manual
CHAPTER 3
AMI BIOS SETUP UTILITY
This chapter provides users with detailed description how to set up
basic system configuration through the AMI BIOS setup utility.
3.1 Starting
To enter the setup screens, follow the steps below:
1. Turn on the computer and press the <Del> key immediately.
2. After you press the <Delete> key, the main BIOS setup menu
displays. You can access the other setup screens from the main
BIOS setup menu, such as the Chipset and Power menus.
3.2 Navigation Keys
The BIOS setup/utility uses a key-based navigation system called hot
keys. Most of the BIOS setup utility hot keys can be used at any time
during the setup navigation process.
These keys include <F1>, <F10>, <Enter>, <ESC>, <Arrow> keys, and
so on.
Note Some of navigation keys differ from one screen to another.
Å Left/Right
ÇÈ Up/Down
+− Plus/Minus
Tab
F1
AMI BIOS Setup Utility
The Left and Right <Arrow> keys allow you to select
a setup screen.
The Up and Down <Arrow> keys allow you to select
a setup screen or sub-screen.
The Plus and Minus <Arrow> keys allow you to
change the field value of a particular setup item.
The <Tab> key allows you to select setup fields.
The <F1> key allows you to display the General
Help screen.
33
IFO2175-830 Series Panel PC User’s Manual
The <F10> key allows you to save any changes you
F10
Esc
Enter
have made and exit Setup. Press the <F10> key to
save your changes.
The <Esc> key allows you to discard any changes
you have made and exit the Setup. Press the
<Esc> key to exit the setup without saving your
changes.
The <Enter> key allows you to display or change the
setup option listed for a particular setup item. The
<Enter> key can also allow you to display the setup
sub- screens.
3.3 Main Menu
When you first enter the Setup Utility, you will enter the Main setup
screen. You can always return to the Main setup screen by selecting
the Main tab. There are two Main Setup options. They are described in
this section. The Main BIOS Setup screen is shown below.
z System Time/Date
Use this option to change the system time and date. Highlight
34
AMI BIOS Setup Utility
IFO2175-830 Series Panel PC User’s Manual
System Time or System Date using the <Arrow> keys. Enter new
values through the keyboard. Press the <Tab> key or the <Arrow>
keys to move between fields. The date must be entered in
MM/DD/YY format. The time is entered in HH:MM:SS format.
3.4 Advanced Menu
The Advanced menu allows users to set configuration of the CPU and
other system devices. You can select any of the items in the left frame
of the screen to go to the sub menus:
y CPU Configuration
y IDE Configuration
y SuperIO Configuration
y Hardware Health Configuration
y ACPI Configuration
y APM Configuration
y MPS Configuration
y PCI Express Configuration
y USB Configuration
For items marked with “f”, please press <Enter> for more options.
AMI BIOS Setup Utility
35
IFO2175-830 Series Panel PC User’s Manual
z Configure advanced CPU settings
This screen shows the CPU Configuration, and you can change the
value of the selected option.
¾ Max CPUID Value Limit
You can enable this item to let legacy operating systems
boot even without support for CPUs with extended CPU ID
functions.
36
¾ Execute-Disable Bit Capability
This item helps you enable or disable the No-Execution
Page Protection Technology.
¾ Hyper Threading Technology
Use this item to enable or disable Hyper-Threading
Technology, which makes a single physical processor
perform multi-tasking function as two logical ones.
¾ Intel (R) SpeedStep (tm) tech
This item helps you enable or disable the Intel SpeedStep
Technology.
¾ Intel (R) C-STATE tech
Use this item to enable or disable the C-State technology.
AMI BIOS Setup Utility
IFO2175-830 Series Panel PC User’s Manual
¾ Enhanced C-States
This item allows you to enable or disable any available
enhanced C-states (C1E, C2E, C3E, C4E and Hard C4E).
z IDE Configuration
You can use this screen to select options for the IDE Configuration,
and change the value of the selected option. A description of the
selected item appears on the right side of the screen. For items
marked with “f”, please press <Enter> for more options.
¾ Primary/Secondary/Third IDE Master/Slave
Select one of the hard disk drives to configure IDE devices
installed in the system by pressing <Enter> for more options.
z SuperIO Configuration
You can use this screen to select options for the SuperIO Configuration,
and change the value of the selected option. A description of the
selected item appears on the right side of the screen.
AMI BIOS Setup Utility
37
IFO2175-830 Series Panel PC User’s Manual
¾ Serial Port1 Address
This item specifies the base I/O port address and Interrupt
Request address of serial port 1. The Optimal setting is
3F8/IRQ4. The Fail-Safe default setting is 3F8.
38
¾ Serial Port1 IRQ
This item specifies the IRQ used by the serial port 1.
¾ Serial Port2 Address
This item specifies the base I/O port address and Interrupt
Request address of serial port 2. The Optimal setting is
2F8/IRQ3. The Fail-Safe setting is 2F8.
¾ Serial Port2 IRQ
This item specifies the IRQ used by the serial port 2.
¾ Serial Port3 Address
This item specifies the base I/O port address and Interrupt
Request address of serial port 3.
¾ Serial Port3 IRQ
This item specifies the IRQ used by the serial port 3.
AMI BIOS Setup Utility
IFO2175-830 Series Panel PC User’s Manual
¾ Serial Port4 Address
This item specifies the base I/O port address and Interrupt
Request address of serial port 4.
¾ Serial Port4 IRQ
This item specifies the IRQ used by the serial port 4.
AMI BIOS Setup Utility
39
IFO2175-830 Series Panel PC User’s Manual
z Hardware Health Configuration
This screen shows the Hardware Health Configuration, and a
description of the selected item appears on the right side of the
screen.
40
¾ System Temperature/CPU Temperature
These items display the temperature of CPU and System,
Vcore, etc.
AMI BIOS Setup Utility
IFO2175-830 Series Panel PC User’s Manual
z ACPI Settings
You can use this screen to select options for the ACPI Settings,
and change the value of the selected option. A description of the
selected item appears on the right side of the screen.
AMI BIOS Setup Utility
41
IFO2175-830 Series Panel PC User’s Manual
z APM Configuration
You can use this screen to select options for the APM
Configuration, and change the value of the selected option. A
description of the selected item appears on the right side of the
screen.
¾ Power Management/APM
Set this item to allow Power Management/APM support. The
default setting is Enabled.
Set this item to prevent the chipset power
Disabled
Enabled
¾ Video Power Down Mode
management and APM (Advanced Power
Management) features.
Set this item to allow the chipset power
management and APM (Advanced Power
Management) features. This is the default
setting.
This option specifies the Power State that the video
subsystem enters when the BIOS places it in a power saving
state after the specified period of display inactivity has
42
AMI BIOS Setup Utility
IFO2175-830 Series Panel PC User’s Manual
expired. The default setting is Suspend.
This setting prevents the BIOS from initiating
Disabled
Suspend
¾ Hard Disk Drive Power Down Mode
any power saving modes concerned with the
video display or monitor.
This option places the monitor into suspend
mode after the specified period of display
inactivity has expired. This means the monitor is
not off. The screen will appear blacked out. The
standards do not cite specific power ratings
because they vary from monitor to monitor, but
this setting use less power than Standby mode.
This is the default setting.
This option specifies the power conserving state that the
hard disk drive enters after the specified period of hard drive
inactivity has expired. The default setting is Suspend.
Disabled
Suspend
This setting prevents hard disk drive power
down mode.
This option cuts the power to the hard disk
drives during a system suspend. This is the
default setting.
¾ Suspend Time Out (Minute)
This option specifies the length of time the system waits
before it enters suspend mode. The default setting is
Disabled.
Disabled
1 Min
4 Min
10 Min
¾ Throttle Slow Clock Ratio
Use this item to specify the speed of the system clock when
running the power saving states.
¾ Power Button Mode
This option specifies how the externally mounted power
AMI BIOS Setup Utility
This setting prevents the system from entering
suspend mode. This is the default setting.
Set this item to allow the computer system to enter
suspend mode after being inactive for 1 minute.
Set this item to allow the computer system to enter
suspend mode after being inactive for 4 minutes.
Set this item to allow the computer system to enter
suspend mode after being inactive for 10 minutes.
43
IFO2175-830 Series Panel PC User’s Manual
button on the front of the computer chassis is used. The
default setting is On/Off.
Pushing the power button turns the computer
On/Off
Suspend
on or off. This is the default setting. This is the
default setting.
Pushing the power button places the computer
in Suspend mode or Full On power mode.
*** Advanced Resume Event Controls ***
¾ Resume On Ring
This item enables or disables the function of Resume On
Ring that resumes the system through incoming calls.
¾ Resume On RTC Alarm
You can set “Resume On RTC Alarm” item to enabled and
key in Data/time to power on system.
44
AMI BIOS Setup Utility
IFO2175-830 Series Panel PC User’s Manual
z MPS Configuration
This screen shows the MPS (Multi Processor Specification)
Configuration, and you can change its value. A description of the
selected item appears on the right side of the screen.
¾ MPS Revision
Use this item to select MPS (Multi Processor Specification)
Revision 1.1 or 1.4. The default setting is 1.4.
AMI BIOS Setup Utility
45
IFO2175-830 Series Panel PC User’s Manual
z PCI Express Configuration
This screen shows the PCI Express Configuration, and you can
change its value. A description of the selected item appears on the
right side of the screen.
¾ Active State Power-Management
Use this item to enable or disable the function of Active
State Power-Management to provide you with lower power
consumption. The default setting is Disabled.
46
AMI BIOS Setup Utility
IFO2175-830 Series Panel PC User’s Manual
z USB Configuration
You can use this screen to select options for the USB
Configuration, and change the value of the selected option. A
description of the selected item appears on the right side of the
screen.
¾ Legacy USB Support
Use this item to enable or disable support for USB device on
legacy operating system. The default setting is Enabled.
¾ USB 2.0 Controller Mode
Use this item to configure the USB 2.0 controller. The
default setting is HiSpeed.
¾ BIOS EHCI Hand-Off
Enabling this item provide the support for operating systems
without an EHCI hand-off feature. The default setting is
Enabled.
AMI BIOS Setup Utility
47
IFO2175-830 Series Panel PC User’s Manual
3.5 PCI PnP Menu
The PCI PnP menu allows users to change the advanced settings for
PCI/PnP devices.
48
(1)
AMI BIOS Setup Utility
IFO2175-830 Series Panel PC User’s Manual
(2)
¾
Clear NVRAM
Use this item to clear the data in the NVRAM (CMOS). Here
are the options for your selection, No and Yes.
¾ Plug & Play O/S
When the setting is No, Use this item to configure all the
devices in the system. When the setting is Yes and if you
install a Plug and Play operating system, the operating
system configures the Plug and Play devices not required
for boot. The default setting is Yes.
¾ PCI Latency Timer
This item controls how long a PCI device can hold the PCI
bus before another takes over. The longer the latency, the
longer the PCI device can retain control of the bus before
handing it over to another PCI device. There are several
options for your selection.
¾ Allocate IRQ to PCI VGA
This item allows BIOS to choose an IRQ to assign for the
PCI VGA card. Here are the options for your selection, No
AMI BIOS Setup Utility
49
IFO2175-830 Series Panel PC User’s Manual
and Yes.
¾ Palette Snooping
Some old graphic controllers need to “snoop” on the VGA
palette, and then map it to their display as a way to provide
boot information and VGA compatibility. This item allows
such snooping to take place. Here are the options for your
selection, Disabled and Enabled.
¾ PCI IDE BusMaster
This item is a toggle for the built-in driver that allows the
onboard IDE controller to perform DMA (Direct Memory
Access) transfer. Here are the options for your selection,
Disabled and Enabled.
¾ OffBoard PCI/ISA IDE Card
This item is for any other non-onboard PCI/ISA IDE
controller adapter. There are several options for your
selection.
¾ IRQ3/4/5/7/9/10/11/14/15
These items will allow you to assign each system interrupt a
type, depending on the type of device using the interrupt.
The option “Available” means the IRQ is going to assign
automatically. Here are the options for your selection,
Available and Reserved.
¾ DMA Channel 0/1/3/5/6/7
These items will allow you to assign each DMA channel a
type, depending on the type of device using the channel.
The option “Available” means the channel is going to assign
automatically. Here are the options for your selection,
Available and Reserved.
50
AMI BIOS Setup Utility
IFO2175-830 Series Panel PC User’s Manual
3.6 Boot Menu
The Boot menu allows users to change boot options of the system. You
can select any of the items in the left frame of the screen to go to the
sub menus:
y Boot Settings Configuration
y Boot Device Priority
y Removable Drives
y Lan Boot Settings Configuration
For items marked with “f”, please press <Enter> for more options.
AMI BIOS Setup Utility
51
IFO2175-830 Series Panel PC User’s Manual
z Boot Settings Configuration
¾ Quick Boot
Enabling this item lets the BIOS skip some power on self
tests (POST). The default setting is Enabled.
52
¾ Quiet Boot
Disabled
Enabled
¾ AddOn ROM Display Mode
Set this item to allow the computer system
to display the POST messages.
Set this item to allow the computer system
to display the OEM logo. This is the
default setting.
This item selects the display mode for option ROM. The
default setting is Force BIOS.
¾ Boot Num-Lock
Use this item to select the power-on state for the NumLock.
The default setting is On.
¾ PS/2 Mouse Support
This item determines if the BIOS should reserve IRQ12 for
the PS/2 mouse or allow other devices to make use of this
AMI BIOS Setup Utility
IFO2175-830 Series Panel PC User’s Manual
IRQ. Here are the options for your selection, Auto, Enabled
and Disabled.
¾ Wait For ‘F1’ If Error
If this item is enabled, the system waits for the F1 key to be
pressed when error occurs. The default setting is Enabled.
¾ Hit ‘DEL’ Message Display
If this item is enabled, the system displays the message
“Press DEL to run Setup” during POST. The default setting
is Enabled.
z Boot Device Priority
The Boot Device Priority screen specifies the the boot device
priority sequence from the available devices.
AMI BIOS Setup Utility
53
IFO2175-830 Series Panel PC User’s Manual
z Removable Drives
Use this screen to view the removable drives in the system. The
BIOS will attempt to arrange the removable drive boot sequence
automatically. You can also change the booting sequence.
54
AMI BIOS Setup Utility
IFO2175-830 Series Panel PC User’s Manual
z Lan Boot Settings Configuration
The Lan Boot Settings Configuration can enable or disable Lan
Boot ROM to allow the system boot on LAN.
AMI BIOS Setup Utility
55
IFO2175-830 Series Panel PC User’s Manual
3.7 Security Menu
The Security menu allows users to change the security settings for the
system.
56
¾ Supervisor Password
This item indicates whether a supervisor password has been
set. If the password has been installed, Installed displays. If
not, Not Installed displays.
¾ User Password
This item indicates whether a user password has been set. If
the password has been installed, Installed displays. If not,
Not Installed displays.
¾ Change Supervisor Password
Select this option and press <Enter> to access the sub
menu. You can use the sub menu to change the supervisor
password.
¾ Change User Password
Select this option and press <Enter> to access the sub
menu. You can use the sub menu to change the user
AMI BIOS Setup Utility
IFO2175-830 Series Panel PC User’s Manual
password.
¾ Boot Sector Virus Protection
This option is near the bottom of the Security Setup screen.
The default setting is Disabled.
Disabled
Enabled
Set this item to prevent the Boot Sector Virus
Protection. This is the default setting.
Select Enabled to enable boot sector protection.
It displays a warning when any program (or
virus) issues a Disk Format command or
attempts to write to the boot sector of the hard
disk drive. If enabled, the following appears
when a write is attempted to the boot sector.
You may have to type N several times to prevent
the boot sector write.
Boot Sector Write!
Possible VIRUS: Continue (Y/N)? _
The following appears after any attempt to
format any cylinder, head, or sector of any hard
disk drive via the BIOS INT 13 Hard disk drive
Service:
Format!!!
Possible VIRUS: Continue (Y/N)?
AMI BIOS Setup Utility
57
IFO2175-830 Series Panel PC User’s Manual
3.8 Chipset Menu
The Chipset menu allows users to change the advanced chipset
settings. You can select any of the items in the left frame of the screen
to go to the sub menus:
y North Bridge Configuration
y South Bridge Configuration
For items marked with “f”, please press <Enter> for more options.
58
AMI BIOS Setup Utility
IFO2175-830 Series Panel PC User’s Manual
z North Bridge Configuration
¾ DRAM Frequency
This item allows you to control the Memory Clock.
¾ Configure DRAM Timing by SPD
This item can enable or disable DRAM timing by SPD (Serial
Presence Detect) device, which is a small EEPROM chip on
the memory module, containing important information about
the module speed, size, addressing mode and various
parameters.
¾ Boot Graphic Adapter Priority
This item allows you to select the graphics controller as the
primary boot device.
¾ Internal Graphics Mode Select
This item allows you to select the amount of system memory
used by the internal graphics device.
¾ Video Function Configuration
Press <Enter> for the sub-menu for setting up video function.
AMI BIOS Setup Utility
59
IFO2175-830 Series Panel PC User’s Manual
60
AMI BIOS Setup Utility
IFO2175-830 Series Panel PC User’s Manual
z South Bridge Configuration
(1)
AMI BIOS Setup Utility
61
IFO2175-830 Series Panel PC User’s Manual
(2)
62
¾ USB Function
This item allows you to enable or disable USB function.
¾ USB 2.0 Controller
This item allows you to enable or disable the USB 2.0
controller.
¾ Audio Controller
This item allows you to enable or disable the audio support.
¾ SLP_S4# Min. Assertion Width
This item allows you to set the SLP_S4# Assertion Width.
¾ Restore on AC Power Loss
This item can control how the PC will behave once power is
restored following a power outage, or other unexpected
shutdown.
¾ PCIE Port Configuration
This item allows you to set or disable the PCI Express Ports.
AMI BIOS Setup Utility
IFO2175-830 Series Panel PC User’s Manual
3.9 Exit Menu
The Exit menu allows users to load your system configuration with
optimal or failsafe default values 0
¾ Save Changes and Exit
When you have completed the system configuration
changes, select this option to leave Setup and reboot the
computer so the new system configuration parameters can
take effect. Select Save Changes and Exit from the Exit
menu and press <Enter>. Select Ok to save changes and
exit.
¾ Discard Changes and Exit
Select this option to quit Setup without making any
permanent changes to the system configuration. Select
Discard Changes and Exit from the Exit menu and press
<Enter>. Select Ok to discard changes and exit.
¾ Discard Changes
Use this item to abandon all changes.
AMI BIOS Setup Utility
63
IFO2175-830 Series Panel PC User’s Manual
¾ Load Optimal Defaults
It automatically sets all Setup options to a complete set of
default settings when you select this option. The Optimal
settings are designed for maximum system performance, but
may not work best for all computer applications. In particular,
do not use the Optimal Setup options if your computer is
experiencing system configuration problems. Select Load
Optimal Defaults from the Exit menu and press <Enter>.
¾ Load Fail-Safe Defaults
It automatically sets all Setup options to a complete set of
default settings when you select this option. The Fail-Safe
settings are designed for maximum system stability, but not
maximum performance. Select the Fail-Safe Setup options if
your computer is experiencing system configuration
problems.
Select Load Fail-Safe Defaults from the Exit menu and press
<Enter>. Select Ok to load Fail-Safe defaults.
64
AMI BIOS Setup Utility
IFO2175-830 Series Panel PC User’s Manual
CHAPTER 4
DRIVER INSTALLATION
4.1 System
IFO2175-830 supports Windows XP/ Windows Vista to facilitate the
installation of system driver, please carefully read the instructions in
this chapter before start installing.
1. Insert Driver CD in the disk, and select the \IFO2175-830\Driver\..
2. Please follow folder Step 1 to Step 7 for IFO2175-830 driver
installation.
Appendix
65
IFO2175-830 Series Panel PC User’s Manual
4.2 Touch Screen
4.2.1 Specification
Touch Screen
Touch Screen Controller
Communications
Baud Rate
Resolution
Power Input
Power Consumption
Board Size
Portrait
For 5-wire analog resistive type
PenMount 6000 microcontroller
USB Full-speed, 12Mbps
19200/ 9600
1024 x 1024
5V
Standby Mode : 13.4mA; Active Mode:
24.6mA
(VCC=5V, Top sheet Panel Resistance: 274
ohm, Bottom sheet Panel Resistance: 770
ohm)
60 x 26 mm
Support 90o, 180o and 270o screen rotation
66
AMI BIOS Setup Utility
IFO2175-830 Series Panel PC User’s Manual
4.2.2 Driver Installation
The IFO2175-830 Series provides a driver of the touch screen that
users can install it under operating system Windows XP/ Windows
Vista. To facilitate this touch screen driver installation, users should
read the instructions in this chapter carefully before start the installation.
1. Insert Driver CD and select the D:\IFO2175-830\Driver\Step6 Touch\Driver\Win2000-XP\setup.exe
2. Follow the installing procedure and press OK.
3. Click Start menu and select “PenMount Utilities”, and then a
“PenMount Control Panel” pops out.
4. Click the “Standard Calibration” button.
Appendix
67
IFO2175-830 Series Panel PC User’s Manual
5. Calibration:
To adjust the display with touch panel, click “Calibration” and
follow the calibrate point to do calibration; there are five points on
screen for calibration.
6. Press OK.
68
AMI BIOS Setup Utility
Loading...