Page 1
GOT817L-511
17” SXGA TFT
Touch Panel Computer
User’s Manual
IP69K certification distinguishes the highest level of
reliability.
Page 2
ii
Disclaimers
This manual has been carefully checked and believed to contain accurate
information. Axiomtek Co., Ltd. assumes no responsibility for any infringements of
patents or any third party’s rights, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the
accuracy, completeness or usefulness of any information in this document. Axiomtek
does not make any commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any
time without notice.
No part of this document may be reproduced, stored in a retrieval system, or
transmitted, in any form or by any means, electronic, mechanical, photocopying,
recording, or otherwise, without the prior written permission of Axiomtek Co., Ltd.
Copyright 2018 Axiomtek Co., Ltd.
All Rights Reserved
November 2018, Version A1
Printed in Taiwan
Page 3
iii
Safety Precautions
Before getting started, please read the following important safety precautions.
1. The GOT817L-511 does not come equipped with an operating system. An
operating system must be loaded first before installing any software into the
computer.
2. Be sure to ground yourself to prevent static charge when installing the internal
components. Use a grounding wrist strap and place all electronic components in
any static-shielded devices. Most electronic components are sensitive to static
electrical charge.
3. Disconnect the power cord from the GOT817L-511 before any installation. Be
sure both the system and external devices are turned OFF. A sudden surge of
power could ruin sensitive components that the GOT817L-511 must be properly
grounded.
4. The brightness of the flat panel display will be getting weaker as a result of
frequent usage. However, the operating period varies depending on the
application environment.
5. Turn OFF the system power before cleaning. Clean the system using a cloth
only. Do not spray any liquid cleaner directly onto the screen. The GOT817L511 may come with a touchscreen. Although the touchscreen is chemical
resistant, it is recommended that you spray the liquid cleaner on a cloth first
before wiping the screen. In case your system comes without the touchscreen,
you must follow the same procedure and not spray any cleaner on the flat panel
directly.
6. Avoid using sharp objects to operate the touchscreen. Scratches on the
touchscreen may cause malfunction or internal failure to the touchscreen.
7. The flat panel display is not susceptible to shock or vibration. When assembling
the GOT817L-511, make sure it is securely installed.
8. Do not open the system’s back cover. If opening the cover for maintenance is a
must, only a trained technician is allowed to do so. Integrated circuits on
computer boards are sensitive to static electricity. To avoid damaging chips
from electrostatic discharge, observe the following precautions:
Before handling a board or integrated circuit, touch an unpainted portion of
the system unit chassis for a few seconds. This will help to discharge any
static electricity on your body.
When handling boards and components, wear a wrist-grounding strap, available
from most electronic component stores.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd. IBM, PC/AT, PS/2, VGA are
trademarks of International Business Machines Corporation.
Intel® and Core™ are registered trademarks of Intel Corporation.
MS-DOS, Microsoft C and Quick BASIC are trademarks of Microsoft Corporation.
VIA is a trademark of VIA Technologies, Inc.
SST is a trademark of Silicon Storage Technology, Inc.
UMC is a trademark of United Microelectronics Corporation. Other brand names and
trademarks are the properties and registered brands of their respective owners.
Page 4
iv
Table of Contents
Safety Precautions ....................................................................................... iii
CHAPTER 1 Introduction ................................................................... 1
1.1 General Description ................................................................... 1
1.2 Specifications ............................................................................. 2
1.2.1 Main CPU Board ................................................................................................ 2
1.2.2 I/O System ......................................................................................................... 2
1.2.3 System Specification .......................................................................................... 2
1.3 Dimensions ................................................................................. 4
1.4 I/O Outlets ................................................................................... 5
1.5 Antenna Installation (Optional) ................................................. 6
1.6 Package List ............................................................................... 7
CHAPTER 2 System Configurations ............................................... 9
2.1 I/O Pin Assignment .................................................................... 9
2.1.1 Serial Port Interface ........................................................................................... 9
2.1.2 Ethernet ........................................................................................................... 10
2.1.3 USB Port .......................................................................................................... 10
2.1.4 DC Power Jack w/ M12 connector ................................................................... 11
2.2 Water-proof Cables .................................................................. 11
2.2.1 Power cable ..................................................................................................... 11
2.2.2 Power adapter for GOT817L-511 .................................................................... 12
2.2.3 COM ................................................................................................................. 12
2.2.4 USB cables ...................................................................................................... 13
2.3 Mounting Method ..................................................................... 13
2.3.1 VESA mounting ................................................................................................ 13
2.3.2 VESA-ARM Mounting....................................................................................... 14
CHAPTER 3 AMI BIOS Setup Utility .............................................. 15
3.1 Navigation Keys ....................................................................... 15
3.2 Main Menu................................................................................. 16
3.3 Advanced Menu ........................................................................ 17
3.4 Chipset Menu ............................................................................ 24
3.5 Security Menu ........................................................................... 26
3.6 Boot Menu ................................................................................. 27
3.7 Save & Exit Menu ..................................................................... 29
CHAPTER 4 Drivers Installation .................................................... 31
4.1 System ...................................................................................... 31
4.2 Touch Screen ........................................................................... 32
4.2.1 Specification ..................................................................................................... 32
4.2.2 Driver Installation- Windows 10 ....................................................................... 32
4.3 Embedded O.S.......................................................................... 34
Page 5
GOT817L-511 User’s Manual
Introduction
1
CHAPTER 1
Introduction
This chapter contains general information and detailed specifications of the
GOT817L-511. Chapter 1 includes the following sections:
General Description
Specification
Dimensions
I/O Outlets
Package List
1.1 General Description
The GOT817L-511 is a fan-less and compact-size touch panel computer, equipped
with a 17” TFT LCD display and low power consumption Intel○R CoreTM i5-7300U
3.5GHz processor. The GOT817L-511 supports Windows® 10 and Windows® 10 IoT
embedded OSs. The panel computer provides Mini card slots of full-size and halfsize each for extension. Its excellent ID and friendly user interface make it a
professional yet easy-to-use panel computer. The GOT817L-511 is an ideal for
space-limited applications in factory automation, machine maker operating systems,
building automation, and more.
GOT817L-511: 17” TFT SXGA Fanless Touch Panel Computer
Reliable and Stable Design
The GOT817L-511 adopts a fanless cooling system, which makes it suitable
for vibration environments, example for Marine and Crane.
Embedded O.S. Supported
The GOT817L-511 not only supports Windows® 10, but also supports
embedded OS, such as Windows® 10 IoT embedded. For storage device,
the GOT817L-511 supports 2.5” SSD or 2.5” SATA HDD device.
Industrial-grade Product Design
The GOT817L-511 has an incredible design to be used in different industrial
environments.
The whole enclosure meets the IP66 standard.
For connecting other devices, the GOT817L-511 also features several
interfaces: USB, Ethernet, and RS-232/422/485.
Page 6
GOT817L-511 User’s Manual
Introduction
2
1.2 Specifications
1.2.1 Main CPU Board
CPU
Intel
®
CoreTM i5-7300U 3.5GHz processor onboard (Kaby Lake)
System Memory
One 260 -pin DDR4-2133 SO-DIMM socket
Maximum memory up to 16GB
BIOS
America Megatrends UEFI BIOS
1.2.2 I/O System
Standard I/O
2 x RS-232/422/485(default RS-232)
4 x USB 2.0 ( M12 connector x 2 )
Ethernet
One Intel
®
i-210LM Gigabit Ethernet ( M12 X-coded connector )
Expansion
Two Mini PCI-E card ( full-size x 1 / half size x 1 )
Storage
One SATA interface
1.2.3 System Specification
17” TFT LCD
17” SXGA 350nits, resolution: 1280x1024
Heat Dispensing Design
Disk drive housing:
One 2.5” SATA drive (optional)
Net Weight
6.94 Kgs (15.3 lb)
Dimension (Main Body Size)
415.92 mm x 348.34 mm x 55 mm
Operation Temperature
-20℃ to +50℃
Page 7
GOT817L-511 User’s Manual
Introduction
3
Relative Humidity
10% to 95% @ 40℃, Non-Condensing
Vibration
5 to 500 Hz, 1.0 G, random for 2.5” SSD
Note
1. All specifications and images are subject to change without notice.
2. The GOT817L-511 is suited on serious environment; please choose the wide
temperature DRAM and SSD.
3. If the operation temperature is higher than 35℃ , the wide temperature
HDD is recommended to be used on the device.
4. If the operation temperature is higher than 45℃ , the wide temperature
CF and SSD are recommended to be used on the device.
Warning: According the warrantee is adopt for the IP66 guarantee, please choose CF,SSD
and RAM by Axiomtek, also please kindly don’t disassemble the system by
youself.
Page 8
GOT817L-511 User’s Manual
Introduction
4
1.3 Dimensions
This diagram shows you dimensions and outlines of the GOT817L-511.
Page 9
GOT817L-511 User’s Manual
Introduction
5
1.4 I/O Outlets
Please refer to the following illustration for I/O locations of the GOT817L-511.
No
Function
1
Backlight ON/OFF
2
Brightness Adjust +/-
3
Power ON/OFF
4
DC Power Connector
5
Ethernet
6
COM1 (RS-232/422/485, default RS-232)
7
COM2 (RS-232/422/485, default RS-232)
8
USB 2.0 x 2
9
USB 2.0 x 2
Page 10
GOT817L-511 User’s Manual
Introduction
6
1.5 Antenna Installation (Optional)
If you have the optional wireless module, you will find the antenna in the accessory
box. The installation instructions are as follows:
1. If you add optional 2T2R WIFI module, the ANT1 is MAIN wifi antenna, the ANT2
is AUX wifi antenna.
2. If you add optional UMTS/HSPA+ module , the ANT1 is main UMTS/GSM
antenna.
3. If you add optional 2T2R WIFI module and UMTS/HSPA+ module , the ANT1 is
MAIN antenna, the ANT2 is AUX antenna, the ANT3 is main UMTS/GSM antenna.
Page 11
GOT817L-511 User’s Manual
Introduction
7
1.6 Package List
When you receive the GOT817L-511, the bundled package should contain the
following items:
GOT817L-511 x 1
Driver DVD x1
DC cable x1
RAM (8G & 16G by optional)
SATA HDD or SSD by optional
24V Power Adapter (optional)
Water-proof Power / USB / LAN / RS-232 cables (optional)
Water-proof Antenna for Wifi or UMTS/HSPA+ (optional)
VESA ARM(optional)
If you can not find the package or any items are missing, please contact Axiomtek distributors
immediately.
Page 12
GOT817L-511 User’s Manual
Introduction
8
This page is intentionally left blank.
Page 13
GOT817L-511 User’s Manual
System Configurations
9
CHAPTER 2
System Configurations
The GOT817L-511 provides rich I/O ports and flexible expansions for you to meet
different demand. The chapter will show you how to install the hardware. It includes:
I/O Pin Assignment
Hard Disk and DRAM
Wireless LAN Card (Optional)
Water-proof cables (Optional)
Hanging and VESA mounting (Optional)
2.1 I/O Pin Assignment
The GOT817L-511 has two serial ports, COM1 and COM2 (RS-232/422/485, default
RS-232) , two USB ports, Ethernet, and DC-in 12V/24V connecter.
2.1.1 Serial Port Interface
The following table 1 shows you the pin assignments of this connector.
COM1 Data/Power Select (JP3)
The COM1 port has +5V power capability on DCD and +12V on RI by setting this
jumper (3x2-pin p=2.0mm). See following table 2.
Table 1: Pin Assignment
Note
Each port +5V Maximum: 2A, +12V Maximum: 1A.
Pin
RS-232
RS-422
RS-485
1
DCD
TX-
Data-
2
RXD
TX+
Data+
3
TXD
RX+
No use
4
DTR
RX-
No use
5
GND
GND
GND
6
DSR
No use
No use
7
RTS
No use
No use
8
CTS
No use
No use
9
RI
No use
No use
Page 14
GOT817L-511 User’s Manual
System Configurations
10
Table 2: Jumpter setting for JP3
Function
Setting
+5V Power
1-3 close
DCD Data:
3-5 close (Default)
+12V Power
2-4 close
RI Data:
4-6 close (Default)
Warning: According the warrantee is adopt for the IP66 guarantee, please inform the COM1
setting when ordering, also please kindly don’t disassemble the system by
youself.
2.1.2 Ethernet
The GOT817L-511 is equipped with a high performance Plug and Play Ethernet
interface, full compliant with IEEE 802.3 standard, and can be connected with a M12
LAN connector.
Please refer to detailed pin assignment list below:
Pin
Signal
1
TX+ (Data transmission positive
2
TX- (Data transmission negative)
3
Rx+(Data reception positive)
4
RJ45 termination
5
RJ45 termination
6
Rx- (Data reception negative)
7
RJ45 termination
8
RJ45 termination
2.1.3 USB Port
The USB is a Universal Serial Bus (compliant with USB 2.0 (480Mbps)) connector on
the rear I/O. It is commonly used for installing USB peripherals such as keyboard,
mouse, scanner, etc.
Pin
Signal
Pin
Signal
1
USB VCC (+5V level)
5
USB VCC (+5V level)
2
USB #0_D-
6
USB #1_D-
3
USB #0_D+
7
USB #1_D+
4
GND
8
GND
Page 15
GOT817L-511 User’s Manual
System Configurations
11
2.1.4 DC Power Jack w/ M12 connector
Pin
Signal
1
+9 ~ 36V
2
+9 ~ 36V
3
GND
4
GND
5
Earth Ground
2.2 Water-proof Cables
GOT800 series uses specific M12 connector for water-proof. Therefore you will
order each cable base on application.
There are four kind cables of GOT800 series, by the optional, if you will apply the
USB, COM or Ethernet then you can select a cable for the package .
The Power cable is included in the accessory box, when you will need the power
adapter, also it can be selected by optional.
2.2.1 Power cable
Please follow pin assignment for the power input.
Pin
Signal
V+
DC 12V or 24V power input
Earth Ground
GND
GND
GND
GND
Page 16
GOT817L-511 User’s Manual
System Configurations
12
2.2.2 Power adapter for GOT817L-511
If you order the power adapter, you should choose the power cord type for your
location. The power adapter is 110-240V which is combined M12 connector.
2.2.3 COM
There are two COM cables which are combined M12 connector. Also, you can refer
2.1.1 for the Series port pin assignment.
Page 17
GOT817L-511 User’s Manual
System Configurations
13
2.2.4 USB cables
The USB cable is combined M12 connector for water-proof. It is extended two USB
ports for application.
2.3 Mounting Method
There are two mounting ways for the GOT817L-511. One is suspension, the other is
VESA mount.
2.3.1 VESA mounting
The GOT817L-511 can accept VESA 100
Page 18
GOT817L-511 User’s Manual
System Configurations
14
2.3.2 VESA-ARM Mounting
Step 1 Find out the 4 screws as marked on the back side of chassis.
Step 2 Assemble the VESA-ARM to the back side of the chassis, and fix the
screws.
Step 3 VESA mounting Installation completed.
Page 19
GOT817L-511 User’s Manual
AMI BIOS Setup Utility 15
CHAPTER 3
AMI BIOS Setup Utility
This chapter provides users with detailed description how to set up basic system configuration
through the AMIBIOS8 BIOS setup utility.
3.1 Navigation Keys
The BIOS setup/utility uses a key-based navigation system called hot keys. Most of
the BIOS setup utility hot keys can be used at any time during the setup navigation
process.
These keys include <F1>, <F2>, <F3>, <F4>, <Enter>, <ESC>, <Arrow> keys, and so
on.
Note
Some of navigation keys differ from one screen to another.
Left/Right
The Left and Right <Arrow> keys allow you to select a setup screen.
Up/Down
The Up and Down <Arrow> keys allow you to select a setup screen or
sub-screen.
+
Plus/Minus
The Plus and Minus <Arrow> keys allow you to change the field value of a
particular setup item.
Tab
The <Tab> key allows you to select setup fields.
F1
The <F1> key allows you to display the General Help screen.
F2
The <F2> key allows you to load previous value
F3
The <F3> key allows you to Load Optimized Defaults.
F4
The <F4> key allows you to save any changes you have made and exit
Setup. Press the <F4> key to save your changes.
Esc
The <Esc> key allows you to discard any changes you have made and
exit the Setup. Press the
<Esc> key to exit the setup without saving your changes.
Enter
The <Enter> key allows you to display or change the setup option listed
for a particular setup item. The <Enter> key can also allow you to display
the setup sub- screens.
Page 20
GOT817L-511 User’s Manual
16 AMI BIOS Setup Utility
3.2 Main Menu
BIOS and EC Information
Display BIOS and EC firmware information.
System Date/Time
Use this option to change the system time and date. Highlight System Time or System Date
using the keys. Enter new values through the keyboard. Press the key or the keys to move
between fields. The date must be entered in MM/DD/YY format. The time is entered in
HH:MM:SS format.
Access Level
Display the access level of current user.
Page 21
GOT817L-511 User’s Manual
AMI BIOS Setup Utility 17
3.3 Advanced Menu
The Advanced menu allows users to set configuration of the CPU and other system
devices. You can select any of the items in the left frame of the screen to go to the
sub menus:
Hardware Monitor
Utility Configuration
Utility Configuration
CPU Configuration
SATA Configuration
PCH-FW Configuration
USB Configuration
Device Configuration (This option appears only if an I/O board is connected CN2 and CN3 See
Section 2.5.1.)
For items marked with “”, please press <Enter> for more options.’
Page 22
GOT817L-511 User’s Manual
18 AMI BIOS Setup Utility
Hardware Monitor
This screen monitors hardware health status.
This screen displays the temperature of system and CPU, system voltages (VBAT, +3.3V,
+3.3V_SBY and +5V).
Page 23
GOT817L-511 User’s Manual
AMI BIOS Setup Utility 19
Utility Configuration
ACPI Settings
Page 24
GOT817L-511 User’s Manual
20 AMI BIOS Setup Utility
ACPI Sleep State
The setting is S3 (Suspend to RAM); this option selects ACPI sleep state the system will enter
when suspend button is pressed.
CPU Configuration
This screen shows the CPU Configuration and you can change the value of the selected
option.
Intel (VMX) Virtualization Technology
Enable or disable Intel Virtualization Technology. When enabled, a VMM (Virtual Machine
Mode) can utilize the additional hardware capabilities. It allows a platform to run multiple
operating systems and applications independently, hence enabling a computer system to work
as several virtual systems.
Page 25
GOT817L-511 User’s Manual
AMI BIOS Setup Utility 21
SATA Configuration
Use this screen to select options for the Super IO Configuration, and change the value of the
selected option
SATA mode selection
The SATA mode is set to AHCI.
mSATA
Enable or disable mSATA feature.
Page 26
GOT817L-511 User’s Manual
22 AMI BIOS Setup Utility
PCH-FW Configuration
This screen displays ME Firmware information.
USB Configuration
Page 27
GOT817L-511 User’s Manual
AMI BIOS Setup Utility 23
USB Devices
Display all detected USB devices.
BIOS Flash Utility
BIOS flash utility configuration. For more detailed information, please refer to Appendix D.
AxiomType3 Super IO Configuration
A description of selected item appears on the right side of the screen. For items marked with
Page 28
GOT817L-511 User’s Manual
24 AMI BIOS Setup Utility
3.4 Chipset Menu
The Chipset menu allows users to change the advanced chipset settings. You can select
“System Agent (SA) Configuration in the left frame of the screen to go to the sub menus:
Page 29
GOT817L-511 User’s Manual
AMI BIOS Setup Utility 25
Graphics Configuration
Use this item to open graphics configuration sub screen.
Memory Configuration
Use this item to refer to information related to system memory.
Page 30
GOT817L-511 User’s Manual
26 AMI BIOS Setup Utility
3.5 Security Menu
The Security menu allows users to change the security settings for the system.
Setup Administrator Password
Use this item to set setup administrator password.
User Password
Use this item to set user password.
Page 31
GOT817L-511 User’s Manual
AMI BIOS Setup Utility 27
3.6 Boot Menu
The Boot menu allows users to change boot options of the system.
Bootup NumLock State
Use this item to select the power-on state for the keyboard NumLock.
Page 32
GOT817L-511 User’s Manual
28 AMI BIOS Setup Utility
Quiet Boot
Select to display either POST output messages or a splash screen during boot-up.
Launch Pxe OPROM
Use this item to enable or disable the boot ROM function of the onboard LAN chip when the
system boots up.
Boot Option Priorities
These are settings for boot priority. Specify the boot device priority sequence from the
available devices.
Hard Drive BBS Priorities
These are settings for configuring the order for a specific device group. These options are only
visible if at least one device for this group is present.
Page 33
GOT817L-511 User’s Manual
AMI BIOS Setup Utility 29
3.7 Save & Exit Menu
Save Changes and Exit
When you have completed the system configuration changes, select this option to leave Setup
and return to Main Menu. Select Save Changes and Exit from the Save & Exit menu and
Discard Changes and Exit
Select this option to quit Setup without making any permanent changes to the system
configuration and return to Main Menu. Select Discard Changes and Exit from the Save & Exit
Save Changes and Reset
When you have completed the system configuration changes, select this option to leave Setup
and reboot the computer so the new system configuration parameters can take effect. Select
Save Changes and Reset from the Save & Exit menu and press . Select Yes to save changes
Discard Changes and Reset
Select this option to quit Setup without making any permanent changes to the system
configuration and reboot the computer. Select Discard Changes and Reset from the Save &
Exit men
Save Changes
Select this option to save changes done so far. Select Save Changes from the Save & Exit
menu and press . Select Yes to save changes.
Page 34
GOT817L-511 User’s Manual
30 AMI BIOS Setup Utility
Discard Changes
Select this option to discard changes done so far and load previous values. Select Discard
Restore Defaults
It automatically sets all Setup options to a complete set of default settings when you select this
Save as User Defaults
Select this option to save system configuration changes done so far as User Defaults. Select
Save as User Defau
Restore User Defaults
It automatically sets all Setup options to a complete set of User Defaults when you select this
Boot Override
Select a drive to immediately boot that device regardless of the current boot order.
Page 35
GOT817L-511 User’s Manual
Drivers Installation 31
CHAPTER 4
Drivers Installation
4.1 System
GOT817L-511 supports only Windows 10-64. To facilitate the installation of system driver,
please carefully read the instructions in this chapter before start installing.
1. Insert Driver CD and select the “\Drivers”.
2. Select all files and follow the installing procedure.
Note
If you didn’t install graphics driver, it only can be resumed via VGA
display when VGA and DP go to sleep mode.
Page 36
GOT817L-511 User’s Manual
32 Drivers Installation
4.2 Touch Screen
The GOT817L-511 uses the 5-wire analog resistive (flat front bezel type). There are
the specification and driver installation which are listed below.
4.2.1 Specification
4.2.2 Driver Installation- Windows 10
The GOT817L-511 provides a touch screen driver that users can install it under the
operating system Windows 10. To facilitate installation of the touch screen driver,
you should read the instructions in this chapter carefully before you attempt
installation.
1. Insert Driver CD and follow the path to select the “\Drivers\Step 7 - Touch”.
2. Follow the installing procedure and press OK.
3. Click Start menu and select “PenMount Utilties”; and then, a “PenMount Control Panel”
pops out.
Touch Screen
5-wire Analog Resistive type
Touch Screen Controller
PenMount 6000 USB Touch Screen Controller IC
Communications
USB interface
Resolution
1024 x 1024
Power Input
5V
Power Consumption
Active: 24.6mA / Idle Mode: 13.4mA
Page 37
GOT817L-511 User’s Manual
Drivers Installation 33
4. Select the “Standard Calibrate” tab.
5. Calibration:
To adjust the display with touch panel, click “Calibration” and follow the calibrate
point to do calibration; there are five points on screen for calibration.
6. Press OK.
Page 38
GOT817L-511 User’s Manual
34 Drivers Installation
4.3 Embedded O.S.
The GOT817L-511 provides the Windows® 10 Embedded. The O.S. is supported
devices which are listed below.
WES 10
Here are supported onboard devices:
Onboard Multi I/O
SATA HDD
USB
LCD display
10/100/1000 base-T Ethernet
mSATA
Touch Screen
Loading...