Page 1
GOT812LR-832
12.1” XGA TFT IP66-rating
Touch Panel Computer
User’s Manual
Page 2
ii
Disclaimers
This manual has been carefully checked and believed to contain accurate
information. Axiomtek Co., Ltd. assumes no responsibility for any infringements of
patents or any third party’ s rights, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the
accuracy, completeness or usefulness of any information in this document. Axiomtek
does not make any commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any
time without notice.
No part of this document may be reproduced, stored in a retrieval system, or
transmitted, in any form or by any means, electronic, mechanical, photocopying,
recording, or otherwise, without the prior written permission of Axiomtek Co., Ltd.
Copyright 2013 Axiomtek Co., Ltd.
All Rights Reserved
Nov. 2013, Version A1
Printed in Taiwan
Note
The GOT812LR-832 is compliant by IEC60945, it is 10~30V power adapter, COM
and USB by Keyboad and Mouse.
Page 3
iii
Safety Precautions
Before getting started, please read the following important safety precautions.
1. The GOT812LR-832 does not come equipped with an operating system. An
operating system must be loaded first before installing any software into the
computer.
2. Be sure to ground yourself to prevent static charge when installing the internal
components. Use a grounding wrist strap and place all electronic components in
any static-shielded devices. Most electronic components are sensitive to static
electrical charge.
3. Disconnect the power cord from the GOT812LR-832 before any installation. Be
sure both the system and external devices are turned OFF. A sudden surge of
power could ruin sensitive components that the GOT812LR-832 must be
properly grounded.
4. The brightness of the flat panel display will be getting weaker as a result of
frequent usage. However, the operating period varies depending on the
application environment.
5. Turn OFF the system power before cleaning. Clean the system using a cloth
only. Do not spray any liquid cleaner directly onto the screen. The GOT812LR832 may come with or w/o a touchscreen. Although the touchscreen is chemical
resistant, it is recommended that you spray the liquid cleaner on a cloth first
before wiping the screen. In case your system comes without the touchscreen,
you must follow the same procedure and not spray any cleaner on the flat panel
directly.
6. Avoid using sharp objects to operate the touchscreen. Scratches on the
touchscreen may cause malfunction or internal failure to the touchscreen.
7. The flat panel display is not susceptible to shock or vibration. When assembling
the GOT812LR-832, make sure it is securely installed.
8. Do not open the system’s back cover. If opening the cover for maintenance is a
must, only a trained technician is allowed to do so. Integrated circuits on
computer boards are sensitive to static electricity. To avoid damaging chips
from electrostatic discharge, observe the following precautions:
Before handling a board or integrated circuit, touch an unpainted portion of
the system unit chassis for a few seconds. This will help to discharge any
static electricity on your body.
When handling boards and components, wear a wrist-grounding strap, available
from most electronic component stores.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd. IBM, PC/AT, PS/2, VGA are
trademarks of International Business Machines Corporation.
Intel® and Atom™ are registered trademarks of Intel Corporation.
MS-DOS, Microsoft C and Quick BASIC are trademarks of Microsoft Corporation.
VIA is a trademark of VIA Technologies, Inc.
SST is a trademark of Silicon Storage Technology, Inc.
UMC is a trademark of United Microelectronics Corporation.Other brand names and
trademarks are the properties and registered brands of their respective owners.
Page 4
iv
Table of Contents
Disclaimers ...................................................................................................... i
Disclaimers ..................................................................................................... ii
Safety Precautions ........................................................................................ iii
CHAPTER 1 INTRODUCTION ...................................................... 1
1.1 General Description .................................................................... 1
1.2 Specifications .............................................................................. 2
1.2.1 Main CPU Board ................................................................................................. 2
1.2.2 I/O System .......................................................................................................... 2
1.2.3 System Specification ........................................................................................... 3
1.3 Dimensions .................................................................................. 4
1.4 I/O Outlets .................................................................................... 5
1.5 Package List ................................................................................ 6
CHAPTER 2 System Configurations .......................................... 7
2.1 I/O Pin Assignment ..................................................................... 7
2.1.1 Serial Port Interface ............................................................................................ 7
2.1.2 COM1 Configuration ............................................................................................... 8
2.1.3 COM port Power Configuration .............................................................................. 9
2.1.4 Ethernet ............................................................................................................ 10
2.2 Water-proof Cables ................................................................... 11
2.2.1 Power cable ...................................................................................................... 11
2.2.2 Power adapter for GOT812LR-832 ................................................................... 12
2.2.3 COM .................................................................................................................. 12
2.2.4 USB cables ....................................................................................................... 13
2.3 Mounting Method ...................................................................... 13
2.3.1 VESA mounting ................................................................................................. 13
2.3.2 VESA-ARM Mounting........................................................................................ 14
CHAPTER 3 AMI BIOS SETUP UTILITY .................................... 15
3.1 Starting ...................................................................................... 15
3.2 Navigation Keys ........................................................................ 15
3.3 Main Menu.................................................................................. 16
3.4 Advanced Menu ......................................................................... 17
3.5 Chipset Menu ............................................................................. 24
3.6 Boot Menu .................................................................................. 26
3.7 Security Menu ............................................................................ 27
3.8 Save & Exit Menu ...................................................................... 28
CHAPTER 4 DRIVERS INSTALLATION .................................... 31
4.1 System ....................................................................................... 31
4.2 Touch Screen ............................................................................ 32
4.3 Embedded O.S........................................................................... 34
Page 5
GOT812LR-832 User’s Manual
Introduction
1
CHAPTER 1
INTRODUCTION
This chapter contains general information and detailed specifications of the
GOT812LR-832. Chapter 1 includes the following sections:
General Description
Specification
Dimensions
I/O Outlets
Package List
1.1 General Description
The GOT812LR-832 is a fan-less and compact-size touch panel computer, equipped
with a 12.1” High brightness TFT LCD display and low power consumption Intel○R
AtomTM N2600 1.6GHz processor. The GOT812LR-832 supports Windows® 7,
Windows® CE.NET and Windows® embedded OSs. The panel computer is able to
install a CompactFlash™ and provided a Mini card slot for extension such as WIFI.
Its excellent ID and friendly user interface make it a professional yet easy-to-use
panel computer. The GOT812LR-832 is an ideal for space-limited applications in
factory automation, machine maker operating systems, building automation, and
more.
GOT812LR-832: 12.1” TFT XGA Fanless Touch Panel Computer
Reliable and Stable Design
The GOT812LR-832 adopts a fanless cooling system and a
CompactFlash™, which makes it suitable for vibration environments,
example for Marine and Crane.
Embedded O.S. Supported
The GOT812LR-832 not only supports Windows® XP and Windows® 7, but
also supports embedded OS, such as Windows® CE.NET, and Windows® 7
embedded. For storage device, the GOT812LR-832 supports
CompactFlash™ and 2.5” SSD device.
Industrial-grade Product Design
The GOT812LR-832 has an incredible design to be used in different
industrial environments.
The whole enclasure meets the IP66 standard.
For connecting other devices, the GOT812LR-832 also features several
interfaces: USB, Ethernet, and RS-232/422/485.
Page 6
GOT812LR-832 User’s Manual
Introduction
2
1.2 Specifications
1.2.1 Main CPU Board
CPU
Intel
®
AtomTM N2600 1.6GHz processor onboard
System Chipset
Intel
®
NM10 Express
System Memory
One 204-pin DDR3 SO-DIMM socket
Maximum memory up to 2GB
BIOS
America Megatrends BIOS
1.2.2 I/O System
Standard I/O
One RS-232 and one RS-232/422/485(default RS-232)
USB 2.0 x 2 (M12 connector)
Ethernet
One RTL81111E Gigabit Ethernet
Expansion
One Mini PCI-E card
Storage
One CF slot
One SATA interface
Page 7
GOT812LR-832 User’s Manual
Introduction
3
1.2.3 System Specification
12.1” TFT LCD
12.1” XGA 1000nits
Heat Dispensing Design
Disk drive housing:
One 2.5” SATA drive (optional)
Net Weight
4.6 Kgs (3.52 lb)
Dimension (Main Body Size)
296mm x 240mm x 59mm
Operation Temperature
-20℃ to 55℃
Relative Humidity
10% to 90% @ 40℃, Non-Condensing
Vibration
5 to 500 Hz, 2.0 G for CF card
5 to 500 Hz, 2.0 G for SSD
Note
1. All specifications and images are subject to change without notice.
2. The GOT812LR-832 is suited on serious environment; please choose the wide
temperature DRAM and SSD.
3. If the operation temperature is higher than 35℃, the wide temperature
HDD is recommended to be used on the device.
4. If the operation temperature is higher than 45℃, the wide temperature
CF and SSD are recommended to be used on the device.
Warning: According the warrantee is adopt for the IP66 guarantee, please choose CF,SSD
and RAM by Axiomtek, also please kindly don’t disassemble the system by
youself.
Page 8
GOT812LR-832 User’s Manual
Introduction
4
1.3 Dimensions
This diagram shows you dimensions and outlines of the GOT812LR-832.
Page 9
GOT812LR-832 User’s Manual
Introduction
5
1.4 I/O Outlets
Please refer to the following illustration for I/O locations of the GOT812LR-832.
No
Function
1
Backlight ON/OFF
2
Brightness Adjust
3
Power Switch(ATX)
4
DC power connector
5
COM1(configure RS422/485, default RS-232)
6
COM2
7
Ethernet
8
USB2.0 × 2
Page 10
GOT812LR-832 User’s Manual
Introduction
6
1.5 Package List
When you receive the GOT812LR-832, the bundled package should contain the following
items:
GOT812LR-832 x 1
Driver CD x1
DC cable x1
Power Adapter (optional)
Water-proof cables (optional)
VESA ARM(optional)
If you can not find the package or any items are missing, please contact Axiomtek distributors
immediately.
Page 11
GOT812LR-832 User’s Manual
System Configurations
7
CHAPTER 2
System Configurations
The GOT812LR-832 provides rich I/O ports and flexible expansions for you to meet
different demand, for example, CF. The chapter will show you how to install the
hardware. It includes:
I/O Pin Assignment
Hard Disk and DRAM
Wireless LAN Card (Optional)
Water-proof cables (Optional)
Hanging and VESA mounting (Optional)
2.1 I/O Pin Assignment
The GOT812LR-832 has two serial ports, COM1 (RS-232/422/485, default RS-232)
and COM2 (RS-232), Ethernet, USB, and DC-in 12V/24V connecter.
2.1.1 Serial Port Interface
The following table shows you the pin assignments of this connector:
Pin
RS-232
RS-422
RS-485
1
DCD
TX-
Data-
2
RXD
TX+
Data+
3
TXD
RX+
No use
4
DTR
RX-
No use
5
GND
GND
GND
6
DSR
No use
No use
7
RTS
No use
No use
8
CTS
No use
No use
9
RI
No use
No use
Page 12
GOT812LR-832 User’s Manual
System Configurations
8
2.1.2 COM1 Configuration
The COM1 is a standard DB-9 connector. This connector is equipped with
The GOT812LR-832 has two serial ports. COM1 is RS-232/422/485, while COM2 is RS-232.
The following table shows you set COM1 port mode:
Description
Jumper Setting
RS-232 (Default)
JP7 JP8
JP9
RS-422
JP7
JP8
JP9
RS-485
JP7
JP8
JP9
Page 13
GOT812LR-832 User’s Manual
System Configurations
9
2.1.3 COM port Power Configuration
All of the serial ports can output data or power through jumper setting.
The following table shows you how to do that.
Description
JP10~JP13
Pin1: DCD
Pin9: RI
(Default)
Pin1: +5V
Pin9: +12V
Pin1: +5V
Pin9: RI
Pin1: DCD
Pin9: +12V
Note
Each port +5V Maximum: 2A, +12V Maximum: 1A.
Warning: According the warrantee is adopt for the IP66 guarantee, please inform the COM1
setting when ordering, also please kindly don’t disassemble the system by
youself.
Page 14
GOT812LR-832 User’s Manual
System Configurations
10
2.1.4 Ethernet
The GOT812LR-832 is equipped with a high performance Plug and Play Ethernet interface,
full compliant with IEEE 802.3 standard, and can be connected with a M12 LAN connector.
Please refer to detailed pin assignment list below:
Pin
Signal
1
TX+ (Data transmission positive
2
TX- (Data transmission negative)
3
Rx+(Data reception positive)
4
RJ45 termination
5
RJ45 termination
6
Rx- (Data reception negative)
7
RJ45 termination
8
RJ45 termination
Page 15
GOT812LR-832 User’s Manual
System Configurations
11
2.2 Water-proof Cables
GOT-800 series uses specific M12 connector for water-proof. Therefore you will
order each cable base on application.
There are four kind cables of GOT812, by the optional, if you will apply the USB,
COM or Etherent then you can select a cable for the package.
The Power cable included in the accessory box, when you will need the power
adapter, also it can be sesected by optional.
2.2.1 Power cable
Please follow pin assignement for the power input.
Pin
Signal
V+
DC 12V or 24V power input
Earth Ground
GND
GND
GND
GND
Page 16
GOT812LR-832 User’s Manual
System Configurations
12
2.2.2 Power adapter for GOT812LR-832
If you order the power adapter, you should choose the power cord type for your
location. The power adapter is +12VDC(5A), 110-240V which is combined M12
connector.
2.2.3 COM
There are two COM cables which are combined M12 connector. Also, you can refer
2.1.1 for the Series port pin assignement.
Page 17
GOT812LR-832 User’s Manual
System Configurations
13
2.2.4 USB cables
The USB cable is combined M12 connector for water-proof. It is extended two USB
ports for applicaton.
2.3 Mounting Method
There are two mounting ways for the GOT812LR-832. One is suspension, the other
is VESA mount.
2.3.1 VESA mounting
The GOT 812 can accept both VESA 75 and VESA 100.
Page 18
GOT812LR-832 User’s Manual
System Configurations
14
2.3.2 VESA-ARM Mounting
Step 1 Find out the 4 screws as marked on the back side of chassis.
Step 2 Assemble the VESA-ARM to the back side of the chassis, and fix the
screws.
Step 3 VESA mounting Installation completed.
Page 19
GOT812LR-832 User’s Manual
AMI BIOS Setup Utility
15
CHAPTER 3
AMI BIOS SETUP UTILITY
This chapter provides users with detailed description how to set up basic system configuration
through the AMIBIOS8 BIOS setup utility.
3.1 Starting
To enter the setup screens, follow the steps below:
Turn on the computer and press the <Del> key immediately.
After you press the <Delete> key, the main BIOS setup menu displays. You can access the
other setup screens from the main BIOS setup menu, such as the Chipset and Power menus.
3.2 Navigation Keys
The BIOS setup/utility uses a key-based navigation system called hot keys. Most of the BIOS
setup utility hot keys can be used at any time during the setup navigation process. These keys
include <F1>, <F2>, <Enter>, <ESC>, <Arrow> keys, and so on.
Note: Some of the navigation keys differ from one screen to another.
Hot Keys
Description
Left/Right
The Left and Right <Arrow> keys allow you to select a setup screen.
Up/Down
The Up and Down <Arrow> keys allow you to select a setup screen or subscreen.
+ Plus/Minus
The Plus and Minus <Arrow> keys allow you to change the field value of a
particular setup item.
Tab
The <Tab> key allows you to select setup fields.
F1
The <F1> key allows you to display the general help screen.
F2
The <F2> key allows you to load previous values.
F3
The <F3> key allows you to load optimized defaults.
F4
The <F4> key allows you to save any changes you have made and exit
setup. Press the <F4> key to save your changes.
Esc
The <Esc> key allows you to discard any changes you have made and exit
the setup. Press the <Esc> key to exit the setup without saving your
changes.
Enter
The <Enter> key allows you to display or change the setup option listed for
a particular setup item. The <Enter> key can also allow you to display the
setup sub- screens.
Page 20
GOT812LR-832 User’s Manual
AMI BIOS Setup Utility
16
3.3 Main Menu
When you first enter the Setup Utility, you will enter the Main setup screen. You can always
return to the Main setup screen by selecting the Main tab. There are two Main Setup options.
They are described in this section. The Main BIOS Setup screen is shown below
System Date/Time
Use this option to change the system time and date. Highlight System Time or System Date
using the <Arrow> keys. Enter new values through the keyboard. Press the <Tab> key or the
<Arrow> keys to move between fields. The date must be entered in MM/DD/YY format. The
time is entered in HH:MM:SS format.
Page 21
GOT812LR-832 User’s Manual
AMI BIOS Setup Utility
17
3.4 Advanced Menu
Launch Storage OpROM
This item can enable or disable boot option for legacy mass storage devices with option ROM.
The Advanced menu also allows users to set configuration of the CPU and other system
devices. You can select any of the items in the left frame of the screen to go to the sub menus:
► ACPI Settings
► CPU Configuration
► IDE Configuration
► USB Configuration
► NCT6627UD Superior IO Configuration
► NCT6627UD HW Monitor
► JMB36X ATA Controller Configuration
For items marked with “”, please press <Enter> for more options.
Page 22
GOT812LR-832 User’s Manual
AMI BIOS Setup Utility
18
ACPI Settings
You can use this screen to select options for the ACPI Configuration, and change the value of
the selected option. A description of the selected item appears on the right side of the screen.
ACPI Sleep State
Use this item to select the highest ACPI sleep state the system will enter.
Page 23
GOT812LR-832 User’s Manual
AMI BIOS Setup Utility
19
CPU Configuration
This screen shows the CPU Configuration, and you can change the value of the selected
option.
Hyper-Threading
Use this item to enable or disable Hyper-Threading Technology, which makes a single
physical processor perform multi-tasking function as two logical ones.
Execute Disable Bit
XD can prevent certain classes of malicious buffer overflow attacks when combined
with a supporting OS (Windows Server 2003 SP1, Windows XP SP2, SuSE Linux 9.2,
RedHat Enterprise 3 Update 3).
Page 24
GOT812LR-832 User’s Manual
AMI BIOS Setup Utility
20
IDE Configuration
SATA Controller(s)
The optional settings are: [Disabled]; [Enabled].
Configure SATA as
The optional settings are: [IDE]; [AHCI].
Page 25
GOT812LR-832 User’s Manual
AMI BIOS Setup Utility
21
USB Configuration
You can use this screen to select options for the USB Configuration, and change the value of
the selected option. A description of the selected item appears on the right side of the screen.
Legacy USB Support
The optional settings are: [Auto]; [Disabled]; [Enabled].
Page 26
GOT812LR-832 User’s Manual
AMI BIOS Setup Utility
22
NCT6627UD Super IO Configuration
You can use this screen to select options for the Super IO Configuration, and change the
value of the selected option. A description of the selected item appears on the right side of the
screen
Serial Port Configuration
Use this item to set parameters of serial port 0~1
Page 27
GOT812LR-832 User’s Manual
AMI BIOS Setup Utility
23
PC Health Status
This screen shows the Hardware Health Configuration, and a description of the selected item
appears on the right side of the screen.
Page 28
GOT812LR-832 User’s Manual
AMI BIOS Setup Utility
24
3.5 Chipset Menu
The Chipset menu allows users to change the advanced chipset settings. You can select any
of the items in the left frame of the screen to go to the sub menus:
► Host Bridge
Host Bridge For items marked with “”, please press <Enter> for more options.
► South Bridge
South Bridge For items marked with “”, please press <Enter> for more options.
Page 29
GOT812LR-832 User’s Manual
AMI BIOS Setup Utility
25
Memory Information
This item is for memory frequency and timing settings. Press <Enter> to go to the sub menu.
Page 30
GOT812LR-832 User’s Manual
AMI BIOS Setup Utility
26
3.6 Boot Menu
The Boot menu allows users to change boot options of the system.
Boot Settings Configuration
Setup Prompt Timeout
Use this item to set number of seconds to wait for setup activation key.
Bootup NumLock State
Use this item to select the power-on state for the NumLock.. The optional settings are: [On];
[Off].
GateA20 Active
If Upon Request is selected, GA20 can be disabled using BIOS services. If Always is selected,
disabling G20 is not allowed; this option is useful when any RT code is executed above 1MB.
Option ROM Messages
Set display mode for option ROM. Configuration options are Force BIOS and Keep Current.
Interrupt 19 Capture
If this item is enabled, this function makes the option ROM to trap Interrupt 19.
Page 31
GOT812LR-832 User’s Manual
AMI BIOS Setup Utility
27
Boot Option Priorities
These are settings for boot priority. Specify the boot device priority sequence from the
available devices.
3.7 Security Menu
The Security menu allows users to change the security settings for the system.
Administrator Password
This item indicates whether an administrator password has been set. If the password has
been installed, Installed displays. If not, Not Installed displays.
User Password
This item indicates whether an user password has been set. If the password has been
installed, Installed displays. If not, Not Installed displays.
Page 32
GOT812LR-832 User’s Manual
AMI BIOS Setup Utility
28
3.8 Save & Exit Menu
The Save & Exit menu allows users to load your system configuration with optimal or fail-safe
default values.
Save Changes and Exit
When you have completed the system configuration changes, select this option to leave Setup
and reboot the computer so the new system configuration parameters can take effect. Select
Save Changes and Exit from the Exit menu and press <Enter>. Select Ok to save changes
and exit.
Discard Changes and Exit
Select this option to quit Setup without making any permanent changes to the system
configuration. Select Discard Changes and Exit from the Exit menu and press <Enter>. Select
Ok to discard changes and exit.
Save Changes and Reset
When you have completed the system configuration changes, select this option to leave Setup
and reboot the computer so the new system configuration parameters can take effect. Select
Save Changes and Reset from the Save & Exit menu and press <Enter>. Select Yes to save
changes and reset.
Discard Changes and Reset
Select this option to quit Setup without making any permanent changes to the system
configuration and reboot the computer. Select Discard Changes and Reset from the Save &
Exit menu and press <Enter>. Select Yes to discard changes and reset.
Page 33
GOT812LR-832 User’s Manual
AMI BIOS Setup Utility
29
Save Changes
When you have completed the system configuration changes, select this option to save
changes. Select Save Changes from the Save & Exit menu and press <Enter>. Select yes to
save changes.
Discard Changes
Select this option to quit Setup without making any permanent changes to the system
configuration. Select Discard Changes from the Save & Exit menu and press <Enter>. Select
Yes to discard changes.
Restore Defaults
It automatically sets all Setup options to a complete set of default settings when you select this
option. Select Restore Defaults from the Save & Exit menu and press <Enter>.
Save as User Defaults
Select this option to save system configuration changes done so far as User Defaults. Select
Save as User Defaults from the Save & Exit menu and press <Enter>.
Restore User Defaults
It automatically sets all Setup options to a complete set of User Defaults when you select this
option. Select Restore User Defaults from the Save & Exit menu and press <Enter>.
Boot Override
Select a drive to immediately boot that device regardless of the current boot order.
Note
If you want to use a CF card that capacity is less than 2GB (such as 1GB,
512MB), we recommend you may switch “A HC I mode” to “ IDE mode” with
"Configure SATA as" of the BIOS setting. And please make sure that users
of Win do ws embedded OS ne ed to install with “I DE ” driver.
Page 34
GOT812LR-832 User’s Manual
AMI BIOS Setup Utility
30
This page is intentionally left blank.
Page 35
GOT812LR-832 User’s Manual
Drivers Installation
31
CHAPTER 4
DRIVERS INSTALLATION
4.1 System
GOT812LR-832 supports Windows 7 and WES 7. To facilitate the installation of system driver,
please carefully read the instructions in this chapter before start installing.
Step 1 Insert Driver CD and select the “\Drivers”.
Step 2 Select all files and follow the installing procedure.
Page 36
GOT812LR-832 User’s Manual
Drivers Installation
32
4.2 Touch Screen
The GOT812 uses the 5-wire analog resistive. There are the specification and driver
installation which are listed below.
Specification
Touch Screen
5-wire Analog Resistive type
Touch Screen Controller
PenMount 6000 USB Touch Screen Controller IC
Communications
USB interface
Baud Rate
19200 baud rate fixed
Resolution
1024 x 1024 (10 bit A/D converter inside)
Power Input
5V
Power Consumption
Active: 24.6mA / Idle Mode: 13.4mA
Driver Installation- Windows 7
The GOT3126T-832 provides a touch screen driver that users can install it under the
operating system Windows 7. To facilitate installation of the touch screen driver, you should
read the instructions in this chapter carefully before you attempt installation.
Step 1 Insert Driver CD and follow the path to select the “\Drivers\Step 5 - Touch”.
Step 2 Follow the installing procedure and press OK.
Step 3 Click Start menu and select “PenMount Utilities”; and then, a “PenMount
Control Panel” pops out.
Page 37
GOT812LR-832 User’s Manual
Drivers Installation
33
Step 4 Select the “Standard Calibrate” tab.
Page 38
GOT812LR-832 User’s Manual
Drivers Installation
34
Step 5 Calibration:
To adjust the display with touch panel, click “Calibration” and follow the calibrate
point to do calibration; there are five points on screen for calibration.
Step 6 Press OK.
Note
1. The windows may be out of rang, because the resolution requests
1024x768 or above when using WIN 7.
2. For the better system performance, please close the Windows AERO or
change to Windows Basic mode.
4.3 Embedded O.S.
The GOT812LR-832 provides the Windows 7 Embedded. The O.S. is supported devices
which are listed below.
WES 7
Here are supported onboard devices:
Onboard Multi I/O
SATA HDD
USB
CRT/LCD display
10/100/1000 base-T Ethernet
Compact Flash
Onboard Audio
Touch Screen
Page 39
GOT812LR-832 User’s Manual
Drivers Installation
35
PenMount Touch screen
Before you can use and calibrate it, here is what you should do:
1. Set up Penmount touch device driver by executing C:\Penmount\ Windows 2000-XP
V5.0\setup.exe. When the installation is finished, an icon “PM” appears on the Taskbar.
2. Calibrate Penmount touch by clicking on the “PM” icon, and the go on the calibration.
3. Restart the computer.
Please be informed if you use the Windows XP OS, the graphic driver supported by Intel is
EMGD, there are three known issues as below:
Note
1. The Intel EMGD package does not include an HDMI audio driver, there
will be an unknown device under device manager.
2. 3D function is not supported.
3. L VDS an d CRT can’t be di sa bled at the s am e time.
Page 40
GOT812LR-832 User’s Manual
Drivers Installation
36
This page is intentionally left blank.
Loading...