Page 1
GOT615-801
15.6” WXGA TFT LCD Fanless
Extended Temperature
PANEL PC
User’s Manual
Page 2
ii
Disclaimers
This manual has been carefully checked and believed to contain
accurate information. Axiomtek Co., Ltd. assumes no responsibility for
any infringements of patents or any third party’s rights, and any liability
arising from such use.
Axiomtek does not warrant or assume any legal liability or
responsibility for the accuracy, completeness or usefulness of any
information in this document. Axiomtek does not make any
commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or
product at any time without notice.
No part of this document may be reproduced, stored in a retrieval
system, or transmitted, in any form or by any means, electronic,
mechanical, photocopying, recording, or otherwise, without the prior
written permission of Axiomtek Co., Ltd.
Copyright 2012 Axiomtek Co., Ltd.
All Rights Reserved
March. 2012, Version A1
Printed in Taiwan
Page 3
iii
Safety Approvals
CE Marking
FCC Class B
FCC Compliance
This equipment has been tested in compliance with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are meant to provide reasonable protection against harmful
interference in a residential installation. If not installed and used in
accordance with proper instructions, this equipment might generate or
radiate radio frequency energy and cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following methods:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment to another outlet of a circuit that doesn’t
connect with the receiver.
4. Consult the dealer or an experienced radio/TV technician for help.
Shielded interface cables must be used in order to comply with the
emission limits.
Page 4
iv
Safety Precautions
Before getting started, please read the following important safety
precautions.
1. The GOT615-801 does not come equipped with an operating
system. An operating system must be loaded first before
installing any software into the computer.
2. Be sure to ground yourself to prevent static charge when
installing the internal components. Use a grounding wrist strap
and place all electronic components in any static-shielded
devices. Most electronic components are sensitive to static
electrical charge.
3. Disconnect the power cord from the GOT615-801 before any
installation. Be sure both the system and external devices are
turned OFF. A sudden surge of power could ruin sensitive
components that the GOT615-801 must be properly grounded.
4. The brightness of the flat panel display will be getting weaker as
a result of frequent usage. However, the operating period varies
depending on the application environment.
5. Turn OFF the system power before cleaning. Clean the system
using a cloth only. Do not spray any liquid cleaner directly onto
the screen. The GOT615-801 may come with or w/o a
touchscreen. Although the touchscreen is chemical resistant, it
is recommended that you spray the liquid cleaner on a cloth first
before wiping the screen. In case your system comes without
the touchscreen, you must follow the same procedure and not
spray any cleaner on the flat panel directly.
6. Avoid using sharp objects to operate the touchscreen.
Scratches on the touchscreen may cause malfunction or
internal failure to the touchscreen.
7. The flat panel display is not susceptible to shock or vibration.
When assembling the GOT615-801, make sure it is securely
installed.
Page 5
v
8. Do not open the system’s back cover. If opening the cover for
maintenance is a must, only a trained technician is allowed to
do so. Integrated circuits on computer boards are sensitive to
static electricity. To avoid damaging chips from electrostatic
discharge, observe the following precautions:
Before handling a board or integrated circuit, touch an
unpainted portion of the system unit chassis for a few
seconds. This will help to discharge any static
electricity on your body.
When handling boards and components, wear a wrist-
grounding strap, available from most electronic component
stores.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd. IBM, PC/AT, PS/2,
VGA are trademarks of International Business Machines Corporation.
Intel® and Atom™ are registered trademarks of Intel Corporation.
MS-DOS, Microsoft C and Quick BASIC are trademarks of Microsoft
Corporation.
VIA is a trademark of VIA Technologies, Inc.
SST is a trademark of Silicon Storage Technology, Inc.
UMC is a trademark of United Microelectronics Corporation.
Other brand names and trademarks are the properties and registered
brands of their respective owners.
Page 6
vi
Table of Contents
Disclaimers .................................................................................... ii
Safety Approvals ........................................................................... iii
Safety Precautions ........................................................................ iv
CHAPTER 1 INTRODUCTION ................................................................ 1
1.1 General Description .................................................... 2
1.2 Specifications .............................................................. 4
1.2.1 Main CPU Board ......................................................... 4
1.2.2 I/O System .................................................................. 4
1.2.3 System Specification ................................................... 5
1.3 Dimensions ................................................................. 6
1.4 I/O Outlets ................................................................... 8
1.5 Packing List ............................................................... 10
CHAPTER 2 HARDWARE INSTALLATION ....................................... 11
2.1 Open back cover ....................................................... 12
2.2 CF card Installation ................................................... 14
2.3 DRAM Installation ..................................................... 16
2.4 HDD Installation ........................................................ 18
2.5 Wireless LAN Card Installation (option) .................... 23
2.6 Serial Ports Interface ................................................ 28
2.7 Ethernet Connector (LAN1, LAN2) ........................... 33
2.8 Mountings: VESA / WALL ......................................... 35
2.8.1 VESA-ARM ................................................................ 35
2.8.2 WALL mounting ......................................................... 36
2.9 Power ........................................................................ 38
CHAPTER 3 AMI BIOS SETUP UTILITY ............................................ 39
3.1 Starting ...................................................................... 39
3.2 Navigation Keys ........................................................ 39
3.3 Main Menu ................................................................ 41
3.4 Advanced Menu ........................................................ 42
3.5 Boot Menu ................................................................. 53
3.6 Security Menu ........................................................... 56
3.7 Chipset Menu ............................................................ 57
3.8 Exit Menu .................................................................. 62
CHAPTER 4 DRIVERS INSTALLATION ......................................... 65
4.1 System ...................................................................... 65
4.2 Touch Screen ............................................................ 66
4.2.1 Specification .............................................................. 66
Page 7
vii
4.2.2 Driver Installation- Windows XP/WIN 7 .................... 66
4.3 Embedded O .S ........................................................ 70
4.3.1 Windows XP Embedded ........................................... 70
4.4 Wake On LAN setting ............................................... 71
Page 8
GOT615-801 User’s Manual
1
CHAPTER 1
INTRODUCTION
This chapter contains general information and detailed specifications
of the GOT615-801. Chapter 1 includes the following sections:
General Description
Specification
Dimensions
I/O Outlets
Package List
Introduction
Page 9
GOT615-801 User’s Manual
2
1.1 General Description
The GOT615-801 adopts a 15.6-inch WXGA color TFT LCD
and low power consumption Intel® AtomTM processor D525 1.8
GHz to provide excellent computing performance and thermal
resistance.With the growing demand of wireless application, it
provides one Mini card slot.
The fanless and wireless platforms are especially designed for
operating under heavy-duty environment. The customers have instant
access wireless LAN. Including transportation, train, control platform
of ships, and oil pipe monitoring systems
Wide Operating Temperature Range
The GOT615-801 features a unique extended temperature
The temperature range from -5°C ~ +45°C, with fanless cooling
system and compact design for harsh environment.
The low power Intel® AtomTM processor D525 1.8GHz, making
the platform a power-efficient solution
Reliable and Stable Design
The GOT615-801 adopts a fan-less cooling system and a
CompactFlash™ card, which makes it especially suitable for
vibration-heavy environments, best for the transportation, ship,
and industrial machinery markets. For high capacity storage
requirement, GOT615-801 can work under 2G (5 ~ 500Hz,
random for CF card) in operation mode with a patent of antivibration design. The patent improves the system reliability and
sustainability.
Introduction
Page 10
GOT615-801 User’s Manual
3
WLAN Antenna Supported
The GOT615-801 provides a PCI Express Mini card slot and WLAN
antenna for wireless network connections. By simply plugging in the
wireless LAN card, customers can use the unit in a wireless
environment.
More Features
GOT615-801 utilizes one 204-pin DDR3 667/800MHz SODIMM
system memory max. up to 4GB,
One SATA HDD and one CompactFlashTM slot and CFCard interface
It provides a full set of I/O including
2 x RS-232,1x RS-232/422/485, 4 x USB 2.0, 1 x audio (line-out),
2 x Gigabit Ethernet and 1 x VGA.
Additionally, this slim unit supports VESA (option) / WALL mount.
Introduction
Page 11
GOT615-801 User’s Manual
4
1.2 Specifications
1.2.1 Main CPU Board
CPU
Intel® Atom™ D525 Processor with (1M Cache, 1.8
GHz )
System Chipset
Intel
BIOS
American Megatrends Inc. BIOS 4Mbit with RPL/PXE
System Memory
One 204-pin DDR3 667/800 MHz SO-DIMM socket
Maximum memory up to 4GB
1.2.2 I/O System
Standard I/O
Two RS-232 and one RS-232/422/485
Four USB 2.0
Ethernet
1 x INTEL 82567V for Gigabit/Fast Ethernet
1 x INTEL 82583V for Gigabit/Fast Ethernet
Audio
One Line-out(Realtek ALC662)
Expansion
One of Mini PCIe Port (internal)
Storage
One slot for CF card(optional)
One SATA(optional)
Power connector
Screw type power connector
Power Rating: 12V, 2.6A
Key-pad
LCD backlight adjustment :3 keys(LCD On/Off,
○R
System Controller Hub ICH8M
Brightness Down/Up)
Introduction
Page 12
GOT615-801 User’s Manual
5
1.2.3 System Specification
15.6” WXGA(1366x768) LCD with LED backlight
5-wire resistive Touch Screen(Higgestec)
Fanless Heat Dispensing Design
IP65, NEMA 4 rugged protection, aluminum front bezel
Disk drive housing:
One 2.5” SATA drive
Net Weight : 3.38kgs
Dimension (Main Body Size)
390x240x59.5
Operation Temperature
-5°C ~ +45°C
Relative Humidity
10% to 90% @ 40℃, Non-Condensing
Power input
12VDC with screw type power connector
Power Rating: 12V, 2.6A
NOTE All specifications and images are subject to change
without
NOTE If the operation temperature is higher than 40℃, the wide
temperature DRAM is recommended to be used on the
device.
Introduction
Page 13
GOT615-801 User’s Manual
6
1.3 Dimensions
The following diagrams show the dimensions and outlines of
GOT615-801.
Introduction
Page 14
GOT615-801 User’s Manual
7
Introduction
Page 15
GOT615-801 User’s Manual
8
1.4 I/O Outlets
Please refer to the following illustration for I/O locations of the
GOT615-801.
Introduction
Page 16
GOT615-801 User’s Manual
9
Introduction
Page 17
GOT615-801 User’s Manual
10
1.5 Packing List
When you receive the GOT615-801, the bundled package should
contain the following items:
GOT615-801 unit x 1
Driver CD x1
Adapter x 1
Screws M2x3L x 1
Screws M6B x 2
Screws M3x4L x 8
CF Mylar x 1
HDD_Bracket x 1
WALL mount bracket
If you can not find the package or any items are missing, please
contact Axiomtek distributors immediately.
Introduction
Page 18
GOT615-801 series User’s Manual
11
CHAPTER 2
HARDWARE INSTALLATION
The GOT615-801 provides rich I/O ports and flexible expansions for
you to meet different demand, for example, CF card. The chapter will
show you how to install the hardware. It includes:
CompactFlash ™ Card
Serial Port
Ethernet
Mounting Method
Hard disk
DRAM
Wireless LAN Card (option)
Hardware Installation
Page 19
GOT615-801 User’s Manual
12
2.1 Open back cover
This section tells users how to open back cover. Please follow the
steps below.
Step 1 Unscrew 8 screws on the back cover. Please refer the
photo below.
Hardware Installation
Page 20
13
Step 2 Remove the back cover.
GOT615-801 series User’s Manual
Hardware Installation
Page 21
GOT615-801 User’s Manual
14
2.2 CF card Installation
The GOT615-801 provides one CF slot for users to install
CompactFlash™ card. Please refer to the following instructions
for installation:
Step 1 Refer to section 2.1 to open the back cover and find out
DIMM Socket on mainboard (CAPA801) from system.
Hardware Installation
Page 22
GOT615-801 series User’s Manual
15
Step 2 Insert the card into the socket, Installation completes.
Hardware Installation
Page 23
GOT615-801 User’s Manual
16
2.3 DRAM Installation
The GOT615-801 provides one 204-pin DDR3 667/800MHz
SODIMM socket that support system memory up to 4GB. Please
follow steps below to install the memory modules:
Step 1 Refer to section 2.1 to open the back cover and find
out DIMM Socket on mainboard (CAPA801) from
system.
Hardware Installation
Page 24
GOT615-801 series User’s Manual
17
Step 2 Pulg DDR3 667/800MHz SODIMM 204-pin memory into slot
with angle of 45°
Step 3 Press the memory into slot.
Hardware Installation
Page 25
GOT615-801 User’s Manual
18
2.4 HDD Installation
The GOT615-801 provides a convenient Hard Disk Drive (HDD)
bracket for users to install 2.5” SATA HDD. Please follow the
steps:
Step 1 Refer to section 2.1 to open the back cover.
Hardware Installation
Page 26
GOT615-801 series User’s Manual
19
Step 2 Take the HDD bracket from the accessories and fix the HDD
bracket.
Hardware Installation
Page 27
GOT615-801 User’s Manual
20
Step 3 Fix the HDD on bracket by 4 screws at the side corner.
Hardware Installation
Page 28
GOT615-801 series User’s Manual
21
Step 4 Fix the HDD bracket into the system, and plug the
data and power cables to HDD. Installation completed.
Hardware Installation
Page 29
GOT615-801 User’s Manual
22
Hardware Installation
Page 30
GOT615-801 series User’s Manual
23
2.5 Wireless LAN Card Installation (option)
The GOT615-801 provides one Mini card slot for user to install
one wireless LAN card. When installing the wireless LAN card,
refer to the following instructions and illustration:
Step 1 Refer to section 2.1 to open the back cover and find
out mini-card slot on the back side of mainboard.
Step 2 Insert the wireless LAN card to the slot. Push it down
firmly until it is clipped by the slot.
Hardware Installation
Page 31
GOT615-801 User’s Manual
24
Hardware Installation
Page 32
GOT615-801 series User’s Manual
25
Setp 3 Fix the card on the M/B by a screw (M2x3L) at the side
corner.
Hardware Installation
Page 33
GOT615-801 User’s Manual
26
Step 4 Connecting the Antenna cable with wireless LAN card
Hardware Installation
Page 34
GOT615-801 series User’s Manual
27
Step 5 Install the antenna on the antenna connector.
Hardware Installation
Page 35
GOT615-801 User’s Manual
28
Pin
Signal
Pin
Signal
1
Data Carrier Detect (DCD)
6
Data Set Ready (DSR)
2
Receive Data (RXD)
7
Request To Send (RTS)
3
Transmit Data (TXD)
8
Clear To Send (CTS)
4
Data Terminal Ready (DTR)
9
Ring Indicator (RI)
5
Ground (GND)
2.6 Serial Ports Interface
The GOT615-801 has threer serial ports. COM1 is RS-232/422/485,
while COM2 and COM3 are RS-232.
The following table shows you the pin assignments of this connector:
Hardware Installation
Page 36
GOT615-801 series User’s Manual
29
Description
Mode
Jumper Setting
COM2
Power;
Pin 1
+5V level
Data;
Pin 1
DCD (Default)
Powe;r
Pin 9
+12V level
Data;
Pin 9
RI
(Default)
The COM2 ports have +5V level power capability on DCD and
+12V level power capability for RI, depending on the JP8
setting.
Hardware Installation
Page 37
GOT615-801 User’s Manual
30
Description
Mode
Jumper Setting
COM3
Power;
Pin 1 +5V level
Data;
Pin 1
DCD (Default)
Powe;r
Pin 9
+12V level
Data;
Pin 9 RI
(Default)
The COM3 ports have +5V level power capability on DCD and +12V
level power capability for RI, depending on the JP7 setting.
Hardware Installation
Page 38
GOT615-801 series User’s Manual
31
Description
Mode
Jumper Setting
COM 1
RS-232
(Default)
JP4 JP5
JP6
RS-422
JP4
JP5
JP6
RS-485
JP4
JP5
JP6
PIN #
Signal Name
RS-232
RS-422
RS-485
1
DCD / +5V
TX-
TX-/RX-
2
RX
TX+
TX+/RX+
3
TX
RX+
NC
4
DTR
RX-
NC
5
GND
GND
GND
6
DSR
NC
NC
7
RTS
NC
NC 8 CTS
NC
NC
9
RI / +12V
NC
NC
COM1 can be set for RS-232/422/485 by jum per. The jump
setting is listed as below:
COM1 RS-232/422/485 Mode Select Jumpers (JP4, JP5, JP6)
When COM1 is set to RS-232,RS-422 or RS-485, the pin assignments
are listed below:
Hardware Installation
Page 39
GOT615-801 User’s Manual
32
Description
Mode
Jumper Setting
COM1
Power;
COM1 Pin 1: +5V level
Data;
COM1 Pin 1: DCD (Default)
Power;
COM1 Pin 9: +12V level
Data;
COM1 Pin 9: RI
(Default)
The COM1 ports have +5V level power capability on DCD and +12V
level power capability for RI, depending on the JP10 setting.
When COM1 is set +5V level or +12V level, please make sure
the Mode is RS-232
Hardware Installation
Page 40
GOT615-801 series User’s Manual
33
Pin
Signal
Pin
Signal
L1L2L3L4L5L6L7L8
A B
A B
L1
MDI0+
L5
MDI2-
L2
MDI0-
L6
MDI1-
L3
MDI1+
L7
MDI3+
L4
MDI2+
L8
MDI3-
A
Active LED (Yellow)
B
100 LAN LED (Green)/ 1000 LAN LED
(Orange)
2.7 Ethernet Connector (LAN1, LAN2)
The GOT615-801 is equipped with a high performance Plug and Play
Ethernet interface, full compliant with IEEE 802.3 standard, and can
be connected with a RJ-45 LAN connector.
The RJ-45 connector is for Ethernet. To connect the board to a
1000/100/10 Base-T hub, just plug one end of the cable into connector
and connect the other end (phone jack) to a 1000/100/10-Base-T hub.
Hardware Installation
Page 41
GOT615-801 User’s Manual
34
Hardware Installation
Page 42
GOT615-801 series User’s Manual
35
2.8 Mountings: VESA / WALL
There are 2 application options for the GOT615-801,
Panel/VESA mountings.
2.8.1 VESA-ARM
The GOT615-801 provides 100x100 VESA mount. Screw four
screws to fix the kit (optional) in the back chassis.
Hardware Installation
Page 43
GOT615-801 User’s Manual
36
2.8.2 WALL mounting
The GOT615-801 is designed for Wall mounting application.
Please refer to the following:
Find out the screws as marked on the back side of chassis.
Hardware Installation
Page 44
GOT615-801 series User’s Manual
37
Hardware Installation
Page 45
GOT615-801 User’s Manual
38
2.9 Power
GOT615-801 equips with a screw type power connector. It
adopts 12VDC. Please follow the signs on power connector to
connect DC power source.
Note: The safty ground must be connected to ensure the uiit
working appropriately.
Hardware Installation
Page 46
GOT615-801 series User’s Manual
39
CHAPTER 3
AMI BIOS SETUP UTILITY
This chapter provides users with detailed description how to set up
basic system configuration through the AMI BIOS setup utility.
3.1 Starting
To enter the setup screens, follow the steps below:
1. Turn on the computer and press the <Del> key immediately.
2. After pressing the <Delete> key, the main BIOS setup menu
displays. You can access to other setup screens from the main
BIOS setup menu, such as the Chipset and Power menus.
3.2 Navigation Keys
The BIOS setup/utility uses a key-based navigation system called hot
keys. Most of the BIOS setup utility hot keys can be used at any time
during the setup navigation process.
These keys include <F1>, <F10>, <Enter>, <ESC>, <Arrow> keys, and
so on.
Note :Some of navigation keys differ from one screen to another.
AMI BIOS Setup Utility
Page 47
GOT615-801 User’s Manual
40
AMI BIOS Setup Utility
Page 48
GOT615-801 series User’s Manual
41
3.3 Main Menu
When you first enter the Setup Utility, you will enter the Main setup
screen. You can always return to the Main setup screen by selecting
the Main tab. System Time/Date can be set up as described below. The
Main BIOS Setup screen is shown below.
System Time/Date
Use this option to change the system time and date.
Highlight System Time or System Date using the
<Arrow> keys. Enter new values through the keyboard.
Press the <Tab> key or the <Arrow> keys to move
between fields. The date must be entered in MM/DD/YY
format. The time is entered in HH:MM:SS format.
AMI BIOS Setup Utility
Page 49
GOT615-801 User’s Manual
42
3.4 Advanced Menu
The Advanced menu allows users to set configuration of the CPU and
other system devices. You can select any of the items in the left frame
of the screen to go to the sub menus:
CPU Configuration
IDE Configuration
Super IO Configuration
Hardware Health Configuration
ACPI Configuration
AHCI Configuration
APM Configuration
USB Configuration
For items marked with “”, please press <Enter> for more options.
AMI BIOS Setup Utility
Page 50
GOT615-801 series User’s Manual
43
Configure advanced CPU settings
This screen shows the CPU Configuration, and you can change
the value of the selected option.
Execute-Disable Bit Capability
Use this item to enable or disable the No-Execution Page
Protection Technology.
Hyper Threading Technology
Use this item to enable or disable Hyper-Threading
Technology, which makes a single physical processor
perform multi-tasking function as two logical ones.
AMI BIOS Setup Utility
Page 51
GOT615-801 User’s Manual
44
IDE Configuration
Use this screen to select options for the IDE Configuration and
change the value of the selected option. Available options of the
selected item appear on the right side of the screen.
For items marked with “ ”, please press <Enter> for more
options.
ATA/IDE Configuration
Use this item to specify the integrated IDE controller. There
are three options for your selection: Disabled, Compatible
and Enhanced.
Primary/Secondary/Third IDE Master
Use this item to select one of the hard disk drives to
configure IDE devices installed in the system by pressing
<Enter> for more options.
AMI BIOS Setup Utility
Page 52
GOT615-801 series User’s Manual
45
Super IO Configuration
Use this item for the Super IO Configuration, and change the
value of the selected option.
Serial Port1 Address
This item specifies the base I/O port address and Interrupt
Request address of serial port 1. The Optimal setting is
3F8/IRQ4. The Fail-Safe default setting is Disabled.
Serial Port2 Address
This item specifies the base I/O port address and Interrupt
Request address of serial port 2.
Serial Port3 Address
This item specifies the base I/O port address and Interrupt
Request address of serial port 3.
AMI BIOS Setup Utility
Page 53
GOT615-801 User’s Manual
46
Hardware Health Configuration
This item shows the Hardware Health Configuration, which
displays the temperature of System, CPUFAN Speed and Vcore,
+12V, +5V, +3.3V.
AMI BIOS Setup Utility
Page 54
GOT615-801 series User’s Manual
47
ACPI Settings
Use this item to select options for the ACPI Settings, and
change the value of the selected option.
General ACPI Configuration
Scroll this item and press <Enter> to view the General
ACPI Configuration sub menu, which contains General
ACPI (Advanced Configuration and Power
Management Interface) options for your configuration.
AMI BIOS Setup Utility
Page 55
GOT615-801 User’s Manual
48
General ACPI Configuration/Suspend mode
Use this item to select which in the Advanced Configuration and
Power Interface(ACPI) state to be used for system suspend.
Here are the options for your selection, S1(POS), S3(STR) and
Auto.
AMI BIOS Setup Utility
Page 56
GOT615-801 series User’s Manual
49
AHCI Configuration
Use this item to select options for the AHCI Configuration and
change the value of the selected option.
AMI BIOS Setup Utility
Page 57
GOT615-801 User’s Manual
50
Disabled
Set this item to prevent the chipset power management
and APM (Advanced Power Management) features.
Enabled
Set this item to allow the chipset power management and
APM (Advanced Power Management) features. This is the
default setting.
APM Configuration
Use this item to select options for the APM Configuration, and
change the value of the selected option. Available options of the
selected item appear on the right side of the screen.
Power Management/APM
Set this item to allow Power Management/APM support. The
default setting is Enabled.
AMI BIOS Setup Utility
Page 58
51
Disabled
This setting prevents the BIOS from initiating any power
saving modes concerned with the video display or monitor.
Suspend
This option places the monitor into suspend mode after the
specified period of display inactivity has expired. This means
the monitor is not off. The screen will appear blacked out. The
standards do not cite specific power ratings because they vary
from monitor to monitor, but this setting use less power than
Standby mode. This is the default setting.
On/Off
Pushing the power button turns the computer on or off. This is
the default setting. This is the default setting.
Suspend
Pushing the power button places the computer in Suspend
mode or Full On power mode.
Video Power Down Mode
This option specifies the Power State. When the BIOS
places it in a power saving state, the video subsystem
enters when the BIOS places it in a power saving state after
the specified period of display inactivity has expired. The
default setting is Suspend.
Power Button Mode
This option specifies how the externally mounted power
button on the front of the computer chassis is used. The
default setting is On/Off.
GOT615-801 series User’s Manual
*** Advanced Resume Event Controls ***
Resume On Ring
This item enables or disables the function of Resume On
Ring that resumes the system through incoming calls.
Resume On RTC Alarm
This item can be set to enabled and key in Data/time to
power on system.
AMI BIOS Setup Utility
Page 59
GOT615-801 User’s Manual
52
USB Configuration
You can use this item to select options for the USB
Configuration, and change the value of the selected option.
USB Function
Use this item to enable or disable USB function.
USB 2.0 Controller
Use this item to enable or disable the USB 2.0 controller.
AMI BIOS Setup Utility
Page 60
GOT615-801 series User’s Manual
53
3.5 Boot Menu
The Boot menu allows users to change boot options of the system. You
can select any of the items in the left frame of the screen to go to the
sub menus:
Boot Settings Configuration
Lan Boot Option
For items marked with “”, please press <Enter> for more options.
AMI BIOS Setup Utility
Page 61
GOT615-801 User’s Manual
54
Boot Settings Configuration
Quick Boot
Enabling this item lets the BIOS skip some power on
self tests (POST). The default setting is Enabled.
Bootup Num-Lock
Use this item to select the power-on state for the
NumLock. The default setting is On.
Wait For ‘F1’ If Error
If this item is enabled, the system waits for the F1 key
to be pressed when error occurs. The default s etting is
Enabled.
Hit ‘DEL’ Message Display
If this item is enabled, the system displays the
message “Press DEL to run Setup” during POST. The
default setting is Enabled.
AMI BIOS Setup Utility
Page 62
GOT615-801 series User’s Manual
55
LAN Boot Option
Use these items to enable or disable the Boot ROM function of
the onboard LAN chip when the system boots up. Available
options of the selected item appear on the right side of the
screen.
LAN1 GbE Controller
This item allows you to enabled or disabled Intel® LAN
Contrller.
LAN2 Boot
Use these items to enable or disable the Boot ROM
function of the onboard LAN chip when the system
boots up.
AMI BIOS Setup Utility
Page 63
GOT615-801 User’s Manual
56
3.6 Security Menu
The Security menu allows users to change the security settings
for the system.
Supervisor Password
This item indicates whether a supervisor password
has been set. If the password has been installed,
『 Installed 』 displays. If not, 『 Not Installed 』
displays.
User Password
This item indicates whether a user password has been
set. If the password has been installed, 『 Installed』
displays. If not, 『Not Installed』 displays.
Change Supervisor Password
Select this option and press <Enter> to access the sub
menu. You can use the sub menu to change the
supervisor password.
Change User Password
Select this option and press <Enter> to access the sub
menu. You can use the sub menu to change the user
password.
AMI BIOS Setup Utility
Page 64
GOT615-801 series User’s Manual
57
3.7 Chipset Menu
The Chipset menu allows users to change the advanced chipset
settings. You can select any of the items in the left frame of the
screen to go to the sub menus:
North Bridge Configuration
South Bridge Configuration
For items marked with “”, please press <Enter> for more options.
AMI BIOS Setup Utility
Page 65
GOT615-801 User’s Manual
58
North Bridge Configuration
Initate Graphic Adapter
When using multiple graphics cards, this item can select
which graphics controller to be the primary display device
during boot.
Internal Graphics Mode Select
This item allows you to select the amount of system memory
used by the internal graphics device.
Video Function Configuration
Press <Enter> for the sub-menu for setting up video function.
AMI BIOS Setup Utility
Page 66
GOT615-801 series User’s Manual
59
Video Function Configuration
DVMT Mode Select
Allow you to select DVMT (Dianomic Video Memory
Technology) mode and Fixed Mode.
DVMT/FIXED Memory
Allow you to allocate a fixed amount of system memory as
graphics memory. Here are the options for your selection,
128MB, 256MB and Maximum DVMT
Boot Display : CRT+LVDS (Only)
AMI BIOS Setup Utility
Page 67
GOT615-801 User’s Manual
60
Flat Panel Type : 1366x768(only) 18 bit
AMI BIOS Setup Utility
Page 68
61
South Bridge Configuration
HDA Controller
This item allows you to enable or disabled the HD audio
support.
GOT615-801 series User’s Manual
AMI BIOS Setup Utility
Page 69
GOT615-801 User’s Manual
62
3.8 Exit Menu
The Exit menu allows users to load the system configuration with
optimal or failsafe default values.
Save Changes and Exit
When you have completed the system configuration
changes, select this option to leave Setup and reboot
the computer so the new system configuration
parameters can take effect. Select Save Changes and
Exit from the Exit menu and press <Enter>. Select Ok
to save changes and exit.
Discard Changes and Exit
Select this option to quit Setup without making any
permanent changes to the system configuration.
Select Discard Changes and Exit from the Exit menu
and press <Enter>. Select Ok to discard changes and
exit.
AMI BIOS Setup Utility
Page 70
GOT615-801 series User’s Manual
63
Discard Changes
Use this item to abandon all changes.
Load Optimal Defaults
It automatically sets all Setup options to a complete
set of default settings when you select this option. The
Optimal settings are designed for maximum system
performance, but may not work best for all computer
applications. In particular, do not use the Optimal
Setup options if your computer is experiencing system
configuration problems.
Select Load Optimal Defaults from the Exit menu and
press <Enter>.
Load Fail-Safe Defaults
It automatically sets all Setup options to a complete
set of default settings when you select this option. The
Fail-Safe settings are designed for maximum system
stability, but not maximum performance. Select the
Fail-Safe Setup options if your computer is
experiencing system configuration problems.
Select Load Fail-Safe Defaults
from the Exit menu and press <Enter>. Select Ok to
load Fail-Safe defaults.
AMI BIOS Setup Utility
Page 71
GOT615-801 User’s Manual
64
MEMO:
AMI BIOS Setup Utility
Page 72
GOT615-801 series User’s Manual
65
CHAPTER 4
DRIVERS INSTALLATION
4.1 System
GOT615-801 supports Windows XP and WIN 7. To facilitate the
installation of system driver, please carefully read the instructions in this
chapter before start installing.
1. Insert Driver CD and select the “\Drivers”.
2. Select all files and follow the installing procedure.
Installation of Drivers
Page 73
GOT615-801 User’s Manual
66
Touch Screen
5-wire Analog Resistive type
Touch Screen Controller
PenMount 6000 USB
Touch Screen Controller IC
Communications
USB interface
Resolution
1024 x 0124 (10 bit A/D converter inside)
Power Input
5V
Power Consumption
Active: 24.6mA / Idle Mode: 13.4mA
4.2 Touch Screen
The GOT615-801 uses the 5-wire analog resistve. There are the
specification and driver installation which are listed below.
4.2.1 Specification
4.2.2 Driver Installation- Windows XP/WIN 7
The GOT615-801 provides a touch screen driver that users can install it
under the operating system Windows XP/Win 7. To facilitate installation
of the touch screen driver, you should read the instructions in this
chapter carefully before you attempt installation.
1. Insert Driver CD and follow the path to select the “\Drivers\Step
5 – Penmountv2.1.0.263”.
Installation of Drivers
Page 74
GOT615-801 series User’s Manual
67
2. Follow the installing procedure and press OK.
Click Start menu and select “PenMount Utilities”; and then, a
“PenMount Control Panel” pops out.
Installation of Drivers
Page 75
GOT615-801 User’s Manual
68
Select the “Standard Calibrate” tab.
Installation of Drivers
Page 76
GOT615-801 series User’s Manual
69
3. Calibration:
To adjust the display with touch panel, click “Calibration” and follow
the calibrate point to do calibration; there are five points on screen
for calibration.
4. Press OK.
Installation of Drivers
Page 77
GOT615-801 User’s Manual
70
4.3 Embedded O .S
The GOT615-801 provides the Windows XP Embedded. The O.S.
is supported devices which are listed below.
4.3.1 Windows XP Embedded
Here are supported onboard devices:
Onboard Multi I/O
SATA HDD
USB
CRT/LCD display
10/100/1000 base-T Ethernet
Compact Flash
Audio (line-out)
Touch Screen
PenMount Touch screen
Before you can use and calibrate it, here is what you should do:
1. Set up Penmount touch device driver by executing
C:\Penmount\ Windows 2000-XP V5.0\setup.exe. When the
installation is finished, an icon “PM” appears on the Taskbar.
2. Calibrate Penmount touch by clicking on the “PM” icon, and the go
on the calibration
3. Restart the computer.
Installation of Drivers
Page 78
GOT615-801 series User’s Manual
71
4.4 Wake On LAN setting
The GOT615-801 supports the wake on LAN function.
Please make the following setting when using this function under
WIN XP and XPE.
Installation of Drivers
Page 79
GOT615-801 User’s Manual
72
Installation of Drivers
Loading...