AXIOMTEK GOT5840T-832 User Manual

Page 1
GOT5840T-832
All-in-One
8.4SVGA TFT Fanless Touch Panel Compact with Intel® AtomTM N2600
Processor Onboard
User’s Manual
Page 2
ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information. Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third partys rights, and any li ability arising from such use. Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy, completeness or usefulness of any information in this document. Axiomtek does not make any commitment to update the information in this manual. Axiomtek reserves the right to change or revise this document and/or product at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Axiomtek Co., Ltd.
Copyright 2013 Axiomtek Co., Ltd.
All Rights Reserved Aug 2013, Version A2 Printed in Taiwan
Page 3
iii
Safety Precautions
Before getting started, please read the following important safety precautions.
1. The GOT5840T-832 does not come equipped with an operating system. An operating system must be loaded first before installing any software into the computer.
2. Be sure to ground yourself to prevent static charge when installing the internal components. Use a grounding wrist strap and place all electronic components in any static-shielded devices. Most electronic components are sensitive to static electrical charge.
3. Disconnect the power cord from the GOT5840T-832 before any installation. Be sure both the system and external devices are turned OFF. A sudden surge of power could ruin sensitive components that the GOT5840T-832 must be properly grounded.
4. The brightness of the flat panel display will be getting weaker as a result of frequent usage. However, the operating period varies depending on the application environment.
5. Turn OFF the system power before cleaning. Clean the system using a cloth only. Do not spray any liquid cleaner directly onto the screen. The GOT5840T-832 comes with a touchscreen. Although the touchscreen is chemical resistant, it is recommended that you spray the liquid cleaner on a cloth first before wiping the screen. In case your system comes without the touchscreen, you must follow the same procedure and not spray any cleaner on the flat panel directly.
6. Avoid using sharp objects to operate the touchscreen. Scratches on the touchscreen may cause malfunction or internal failure to the touchscreen.
7. The flat panel display is not susceptible to shock or vibration. When assembling the GOT5840T-832, make sure it is securely installed.
8. Do not open the system’s back cover. If opening the cover for maintenance is a must, only a trained technician is allowed to do so. Integrated circuits on computer boards are sensitive to static electricity. To avoid damaging chips from electrostatic discharge, observe the following precautions:
Before handling a board or integrated circuit, touch an unpainted portion of the
system unit chassis for a few seconds. This will help to discharge any static electricity on your body.
When handling boards and components, wear a wrist-grounding strap,
available from most electronic component stores.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd. IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation.
Intel® and Atom are registered trademarks of Intel Corporation. MS-DOS, Microsoft C and Quick BASIC are trademarks of Microsoft Corporation. VIA is a trademark of VIA Technologies, Inc. SST is a trademark of Silicon Storage Technology, Inc. UMC is a trademark of United Microelectronics Corporation. Other brand names and trademarks are the properties and registered brands of their respective owners.
Page 4
iv
Table of Contents
Disclaimers .............................................................................................................. ii
Safety Precautions ................................................................................................. iii
CHAPTER 1 INTRODUCTION ........................................................................ 1
1.1 General Description ............................................................................ 1
1.2 Specifications ..................................................................................... 2
1.2.1 Main CPU Board ................................................................................................ 2
1.2.2 I/O System ......................................................................................................... 2
1.2.3 System Specification ........................................................................................ 3
1.3 Dimensions ......................................................................................... 4
1.4 I/O Outlets ........................................................................................... 6
1.5 Packing List ......................................................................................... 6
CHAPTER 2 HARDWARE INSTALLATION .................................................... 7
2.1 CF card Installation ............................................................................. 7
2.2 Jumper and Switch Setting & COM port Connector ......................... 8
2.2.1 COM1 Configuration ......................................................................................... 9
2.2.2 COM port Power Configuration ....................................................................... 9
2.2.3 Auto Power On (JP4) ...................................................................................... 10
2.2.4 Restore BIOS Optimal Defaults (JP6) ........................................................... 10
2.2.5 COM port Connector ...................................................................................... 10
2.3 Ethernet ............................................................................................ 11
2.4 Mountings – Panel/Wall/Desktop/VESA ..................................... 12
2.4.1 Panel Mounting ............................................................................................... 12
2.4.2 Wall-Mounting ................................................................................................. 13
2.4.3 Desktop-Mounting .......................................................................................... 13
2.4.4 VESA-ARM Mounting ...................................................................................... 14
2.5 DRAM Installation ............................................................................. 16
2.6 Wireless LAN Card Installation ........................................................ 18
2.7 Power Input (Phoenix type) .............................................................. 19
CHAPTER 3 AMI BIOS SETUP UTILITY ...................................................... 21
3.1 Starting .............................................................................................. 21
3.2 Navigation Keys ................................................................................ 21
3.3 Main Menu ......................................................................................... 22
3.4 Advanced Menu ................................................................................. 23
3.5 Chipset Menu .................................................................................... 30
3.6 Boot Menu ......................................................................................... 32
3.7 Security Menu ................................................................................... 33
3.8 Exit Menu ........................................................................................... 34
Page 5
v
CHAPTER 4 DRIVERS INSTALLATION ....................................................... 36
4.1 System ............................................................................................... 36
4.2 Touch Screen .................................................................................... 37
4.2.1 Specification .................................................................................................... 37
4.2.2 Driver Installation- Windows 7 ...................................................................... 37
4.3 Embedded O.S. ................................................................................. 39
4.3.1 WES 7 ............................................................................................................... 39
Page 6
vi
This page is intentionally left blank.
Page 7
GOT5840T-832 User’s Manual
Introduction
1
CHAPTER 1
INTRODUCTION
This chapter contains general information and detailed specifications of the GOT5840T-832. Chapter 1 includes the following sections:
General Description Specification Dimensions I/O Outlets Package List
1.1 General Description
The GOT5840T-832 is a fan-less and compact-size touch panel computer, equipped with a
8.4” TFT LCD display and low power consumption Intel○R AtomTM N2600 1.6GHz processor. The GOT5840T-832 supports Windows® 7 32-bit,, WES 7. The panel computer provides a Mini card slot for wireless module. Its excellent ID and friendly user interface make it a professional yet easy-to-use panel computer. The GOT5840T-832 is an ideal for space-limited applications in factory automation, machine maker operating systems, building automation, and more.
GOT5840T-832: 8.4 TFT SVGA Fanless Touch Panel Computer
Reliable and Stable Design
The GOT5840T-832 adopts a fanless cooling system, which makes it suitable for vibration environments.
Embedded O.S. Supported
The GOT5840T-832 not only supports Windows® 7 32-bit, but also supports embedded OS, such as WES 7. For storage device, the GOT5840T-832 supports CompactFlash card.
Industrial-grade Product Design
The GOT5840T-832 has an incredible design to be used in different industrial environments.
The front bezel meets the IP65/NEMA4 standard.
For connecting other devices, the GOT5840T-832 also features several interfaces: USB, Ethernet, and RS-232/422/485.
Page 8
GOT5840T-832 User’s Manual
Introduction
2
1.2 Specifications
1.2.1 Main CPU Board
CPU
Intel
R
AtomTM N2600 1.6GHz processor onboard
System Chipset
Intel
R
NM10 Express
BIOS
America Megatrends BIOS
System Memory
One 204-pin DDR3 800MHz SO-DIMM socket Maximum memory up to 2GB
1.2.2 I/O System
Standard I/O
1x RS-232/422/485, 1x RS232 2x USB 2.0
Ethernet
2x 10/100/1000Mbps Ethernet
Audio
One Line-out
Expansion
1 x mini PCIe slot
Storage
One slot for CompactFlash™
Power connector
GOT5840T-832 : DC power 10~30VDC (phoenix type) GOT5840T-832-J : AC 100~240V to DC 12V adapter(Screw type)
Page 9
GOT5840T-832 User’s Manual
Introduction
3
1.2.3 System Specification
8.4” SVGA(800x600) LCD with LED backlight 5 wired resistive Touch Fanless Heat Dispensing Design Heat Dispensing Design Net Weight
1.3 Kgs (2.87 lb)
Dimension (Main Body Size)
250.7x 45.8 x 204.7mm
Operation Temperature
0 to 50(with W.T. DRAM/HDD in airflow condition)
Relative Humidity
10% to 95% @ 40, Non-Condensing
Vibration
5 to 500 Hz, 2.0 G random for CF card
Power input
10~30VDC with phoenix power connector External 60W AC Adapter
Power Input: 100VAC to 240VAC Power Output: 12VDC, Max. 5A
NOTE: All specifications and images are subject to change without notice.
NOTE: If the operation temperature is higher than 35℃, the wide temperature DRAM and CF
are recommended to be used o the device.
Page 10
GOT5840T-832 User’s Manual
Introduction
4
1.3 Dimensions
This diagram shows you dimensions and outlines of the GOT5840T-832.
Page 11
GOT5840T-832 User’s Manual
Introduction
5
Page 12
GOT5840T-832 User’s Manual
Introduction
6
1.4 I/O Outlets
Please refer to the following illustration for I/O locations of the GOT5840T-832.
No
Function
No
Function
1
POWER SWITCH (ATX)
5
COM 2 (RS-232)
2
Power Input connector (Phoenix)
6
Ethernet (RJ-45)
3
Power Input connector (Screw)
7
Dual USB 2.0 ports
4
COM 1 (RS-232/422/485)
8
AUDIO (LINE-OUT)
1.5 Packing List
When you receive the GOT5840T-832, the bundled package should contain the following items:
GOT5840T-832 x 1 Panel Mount Kit x 6 Driver CD x1 Wall-Mount Kit x1 Phoenix connector x1 (for GOT5840T-832) Power Adapter & power cord (for GOT5840T-832-J)
If you can not find the package or any items are missing, please contact AXIOMTEK distributors immediately.
Page 13
GOT5840T-832 User’s Manual
Hardware Installation
7
CHAPTER 2
HARDWARE INSTALLATION
The GOT5840T-832 provides rich I/O ports and flexible expansions for you to meet different demand. The chapter will show you how to install the hardware. It includes:
CompactFlash Card Serial Port Ethernet Mounting Way DRAM Wireless LAN Card
2.1 CF card Installation
The GOT5840T-832 provides one CF slot for users to install CompactFlash card. Please refer to the following instructions for installation:
Step 1 Turn off the system, and unplug the power cord. Step 2 Find out the cover on the side of the system.
Step 3 Locate the CompactFlashTM socket, and insert the card into the socket.
Page 14
GOT5840T-832 User’s Manual
Hardware Installation
8
2.2 Jumper and Switch Setting & COM port Connector
Jumper is a small component consisting of jumper clip and jumper pins. Install jumper clip on 2 jumper pins to close. And remove jumper clip from 2 jumper pins to open. The following illustration shows how to set up jumper.
Before applying power to GOT5840T-832, please make sure all of the jumpers and switch are in factory default position. Below you can find a summary table and onboard default settings.
Jumper
Description
Setting
JP4
Auto Power On Default: Disable
2-3 close
JP5
CF Voltage Selection Default: +3.3V
1-2 close
JP6
Restore BIOS Optimal Defaults (Clear CMOS) Default: Normal Operation
1-2 close JP7
COM1 RS-232/422/485 Mode Setting Default: RS-232
3-5, 4-6 close
JP8
3-5, 4-6 close
JP9
1-2 close
JP10
COM1 Data/Power Selection Default: RS-232 Data
Pin 1: DCD
3-5 close
Pin 9: RI
4-6 close
JP11
COM2 Data/Power Selection Default: RS-232 Data
Pin 1: DCD
3-5 close
Pin 9: RI
4-6 close
Page 15
GOT5840T-832 User’s Manual
Hardware Installation
9
2.2.1 COM1 Configuration
The COM1 and COM2 are a standard DB-9 connector. The GOT5840T-832 has two serial ports. COM1 is RS-232/422/485, while COM2 is RS-232. The following table shows you set COM1 port mode:
Description
Jumper Setting
RS-232 (Default)
JP7 JP8
JP9
RS-422
JP8
JP7
JP9
RS-485
JP8
JP7
JP9
2.2.2 COM port Power Configuration
All of the serial ports can output data or power through jumper setting.The following table shows you how to do that.
Description
JP10 & JP11
Pin1: DCD Pin9: RI (Default)
Pin1: +5V Pin9: +12V
Pin1: +5V Pin9: RI
Pin1: DCD Pin9: +12V
NOTE: Each port +5V Maximum: 2A, +12V Maximum: 1A.
Page 16
GOT5840T-832 User’s Manual
Hardware Installation
10
2.2.3 Auto Power On (JP4)
If JP4 is enabled for power input, the system will be automatically power on without pressing soft power button. If JP4 is disabled for power input, it is necessary to manually press soft power button to power on the system.
2.2.4 Restore BIOS Optimal Defaults (JP6)
Put jumper clip to pin 2-3 for a few seconds then move it back to pin 1-2. Doing this procedure can restore BIOS optimal defaults.
2.2.5 COM port Connector
The pin assignment of RS-232/RS-422/RS-485 is listed on the following table. If you need COM1 port to support RS-422 or RS-485 mode, please refer to Jumper Settings
Function
Setting
Enable auto power on
1-2 close
Disable auto power on (Default)
2-3 close
Function
Setting
Normal operation (Default)
1-2 close
Restore BIOS optimal defaults
2-3 close
Pin
RS-232
RS-422
RS-485
1
DCD
TX-
Data-
2
RXD
TX+
Data+
3
TXD
RX+
No use
4
DTR
RX-
No use
5
GND
GND
GND
6
DSR
No use
No use
7
RTS
No use
No use
8
CTS
No use
No use
9
RI
No use
No use
Page 17
GOT5840T-832 User’s Manual
Hardware Installation
11
2.3 Ethernet
The GOT5840T-832 is equipped with two high performance Plug and Play Ethernet interfaces, full compliant with IEEE 802.3 standard, and can be connected with a RJ-45 LAN connector.
Please refer to detailed pin assignment list below:
Pin
Signal
1
23456
7
8
RJ-45
1
TX+ (Data transmission positive
2
TX- (Data transmission negative)
3
Rx+(Data reception positive)
4
RJ45 termination
5
RJ45 termination
6
Rx- (Data reception negative)
7
RJ45 termination
8
RJ45 termination
Page 18
GOT5840T-832 User’s Manual
Hardware Installation
12
2.4 Mountings – Panel/Wall/Desktop/VESA
There are several mounting ways for the GOT5840T-832, Panel, Wall, Desktop and VESA mountings.
2.4.1 Panel Mounting
The GOT5840T-832 is designed for panel mount application. A set of standard mounting kit are bundled with the system package that you can use it to mount the GOT5840T-832.
Page 19
GOT5840T-832 User’s Manual
Hardware Installation
13
2.4.2 Wall-Mounting
The GOT5840T-832 is designed for Wall mounting application. Please refer to the following steps: Find out the screws as marked on the back side of chassis.
2.4.3 Desktop-Mounting
The GOT5840T-832 is designed for desktop mounting application. Please refer to the following steps:
Step 1 Find out the screws as marked on the back side of chassis.
Page 20
GOT5840T-832 User’s Manual
Hardware Installation
14
Step 2 Assemble the desktop stand to the chassis, and fix the screws.
2.4.4 VESA-ARM Mounting
Step 1 Find out the screws as marked on the back side of chassis.
Step 2 Assemble the VESA-ARM to the back side of the chassis, and fix the screws.
Page 21
GOT5840T-832 User’s Manual
Hardware Installation
15
Step 3 VESA mounting Installation completed.
CautionUse recommended/suitable mounting apparatus to avoid risk of injury.
Page 22
GOT5840T-832 User’s Manual
Hardware Installation
16
2.5 DRAM Installation
The GOT5840T-832 provides one 204-pin DDR3 800MHz SO-DIMM socket that support system memory up to 2GB. Please follow steps below to install the memory modules:
Step 1 Unscrew six screws to remove the rear chassis.
Step 2 Open the back cover and find mainboard (SBC87832).
Page 23
GOT5840T-832 User’s Manual
Hardware Installation
17
Step 3 Push down latches on each side of the DIMM socket.
Step 4 Install the memory module into the socket and push it firmly down until it is
fully seated. The socket latches are levered upwards and clipped on to the edges of the DIMM.
Page 24
GOT5840T-832 User’s Manual
Hardware Installation
18
2.6 Wireless LAN Card Installation
The GOT5840T-832 provides one Mini card slot for user to install one wireless LAN card. When installing the wireless LAN card, refer to the following instructions and illustration:
Step 1 Open the back cover and find mainboard (SBC87832).
Step 2 Insert the wireless LAN card to the slot. Push it down firmly until it is clipped
by the slot.
Step 3 Find the built-in Antenna cable.
Page 25
GOT5840T-832 User’s Manual
Hardware Installation
19
Step 4 There are two connectors on wireless LAN card. One is MAIN, and the other
is auxiliary. Connect antenna cable to MAIN connector on wireless LAN card.
NOTE: Please have the extented bracket when using half-size mini card.
2.7 Power Input (Phoenix type)
GOT5840T-832 equips with a phoenix type power connector. It adopts 10VDC to 30VDC. Please follow the signs on power connector to connect DC power source.
+: Power positive G: Safety ground :Power negative
NOTE: The safety ground must be connected to ensure the unit working appropriately.
Page 26
GOT5840T-832 User’s Manual
Hardware Installation
20
This page is intentionally left blank.
Page 27
GOT5840T-832 User’s Manual
AMI BIOS Setup Utility
21
CHAPTER 3
AMI BIOS SETUP UTILITY
This chapter provides users with detailed description how to set up basic system configuration through the AMIBIOS8 BIOS setup utility.
3.1 Starting
To enter the setup screens, follow the steps below: Turn on the computer and press the <Del> key immediately. After you press the <Delete> key, the main BIOS setup menu displays. You can access the other setup screens from the main BIOS setup menu, such as the Chipset and Power menus.
3.2 Navigation Keys
The BIOS setup/utility uses a key-based navigation system called hot keys. Most of the BIOS setup utility hot keys can be used at any time during the setup navigation process. These keys include <F1>, <F10>, <Enter>, <ESC>, <Arrow> keys, and so on.
NOTE: Some of navigation keys differ from one screen to another.
Hot Keys
Description
Left/Right
The Left and Right <Arrow> keys allow you to select a setup screen.
 Up/Down
The Up and Down <Arrow> keys allow you to select a setup screen or sub­screen.
+ Plus/Minus
The Plus and Minus <Arrow> keys allow you to change the field value of a particular setup item.
Tab
The <Tab> key allows you to select setup fields.
F1
The <F1> key allows you to display the General Help screen.
F10
The <F10> key allows you to save any changes you have made and exit Setup. Press the <F10> key to save your changes.
Esc
The <Esc> key allows you to discard any changes you have made and exit the Setup. Press the
<Esc> key to exit the setup without saving your changes.
Enter
The <Enter> key allows you to display or change the setup option listed for a particular setup item. The <Enter> key can also allow you to display the setup sub- screens.
Page 28
GOT5840T-832 User’s Manual
AMI BIOS Setup Utility
22
3.3 Main Menu
When you first enter the Setup Utility, you will enter the Main setup screen. You can always return to the Main setup screen by selecting the Main tab. There are two Main Setup options. They are described in this section. The Main BIOS Setup screen is shown below.
System Time/Date
Use this option to change the system time and date. Highlight System Time or System Date using the <Arrow> keys. Enter new values through the keyboard. Press the <Tab> key or the <Arrow> keys to move between fields. The date must be entered in MM/DD/YY format. The time is entered in HH:MM:SS format.
Page 29
GOT5840T-832 User’s Manual
AMI BIOS Setup Utility
23
3.4 Advanced Menu
Launch PXE OpROM
Use this item to enable or disable the boot ROM function of the onboard LAN chip when the system boots up.
Launch Storage OpROM
Enable or disable boot option for legacy mass storage devices with Option ROM. The Advanced menu allows users to set configuration of the CPU and other system devices.
You can select any of the items in the left frame of the screen to go to the sub menus:
ACPI Settings ► CPU Configuration ► IDE Configuration ► USB Configuration ► NCT6627UD Superior IO Configuration ► NCT6627UD HW Monitor ► JMB36X ATA Controller Configuration
For items marked with “”, please press <Enter> for more options.
Page 30
GOT5840T-832 User’s Manual
AMI BIOS Setup Utility
24
ACPI Settings
You can use this screen to select options for the ACPI Settings, and change the value of the selected option. A description of the selected item appears on the right side of the screen.
ACPI Sleep State
Use this item to select the highest ACPI sleep state the system will enter.
Page 31
GOT5840T-832 User’s Manual
AMI BIOS Setup Utility
25
CPU Configuration
This screen shows the CPU Configuration, and you can change the value of the selected option.
Hyper Threading Technology
Use this item to enable or disable Hyper-Threading Technology, which makes a single physical processor perform multi-tasking function as two logical ones.
Execute Disable Bit
This item helps you enable or disable the No-Execution Page Protection Technology
Page 32
GOT5840T-832 User’s Manual
AMI BIOS Setup Utility
26
IDE Configuration
SATA Controller(s)
The optional settings are: [Disabled]; [Enabled].
Configure SATA as
The optional settings are: [IDE]; [AHCI].
Page 33
GOT5840T-832 User’s Manual
AMI BIOS Setup Utility
27
USB Configuration
You can use this screen to select options for the USB Configuration, and change the value of the selected option. A description of the selected item appears on the right side of the screen.
Legacy USB Support
The optional settings are: [Auto]; [Disabled]; [Enabled].
Page 34
GOT5840T-832 User’s Manual
AMI BIOS Setup Utility
28
NCT6627UD Super IO Configuration
You can use this screen to select options for the Super IO Configuration, and change the value of the selected option. A description of the selected item appears on the right side of the screen
Serial Port Configuration
Use this item to set parameters of serial port 0~3.
Page 35
GOT5840T-832 User’s Manual
AMI BIOS Setup Utility
29
PC Health Status
This screen shows the Hardware Health Configuration, and a description of the selected item appears on the right side of the screen.
Page 36
GOT5840T-832 User’s Manual
AMI BIOS Setup Utility
30
3.5 Chipset Menu
The Chipset menu allows users to change the advanced chipset settings. You can select any of the items in the left frame of the screen to go to the sub menus:
Host Bridge Host Bridge For items marked with , please press <Enter> for more options.
South Bridge South Bridge For items marked with , please press <Enter> for more options.
Page 37
GOT5840T-832 User’s Manual
AMI BIOS Setup Utility
31
Memory Frequency and Timing This item is for memory frequency and timing settings. Press <Enter> to go to the sub menu.
Page 38
GOT5840T-832 User’s Manual
AMI BIOS Setup Utility
32
3.6 Boot Menu
The Boot menu allows users to change boot options of the system.
Boot Settings Configuration
Setup Prompt Timeout
Use this item to set number of seconds to wait for setup activation key.
Bootup NumLock State
Use this item to select the power-on state for the NumLock.. The optional settings are: [On]; [Off].
GateA20 Active
If Upon Request is selected, GA20 can be disabled using BIOS services. If Always is selected, disabling G20 is not allowed; this option is useful when any RT code is executed above 1MB.
Option ROM Messages
Set display mode for option ROM. Configuration options are Force BIOS and Keep Current.
Interrupt 19 Capture
If this item is enabled, this function makes the option ROM to trap Interrupt 19.
Boot Option Priorities
These are settings for boot priority. Specify the boot device priority sequence from the available devices.
Page 39
GOT5840T-832 User’s Manual
AMI BIOS Setup Utility
33
3.7 Security Menu
The Security menu allows users to change the security settings for the system.
Administrator Password
This item indicates whether an administrator password has been set. If the password has been installed, Installed displays. If not, Not Installed displays.
User Password
This item indicates whether a user password has been set. If the password has been installed, Installed displays. If not, Not Installed displays.
Page 40
GOT5840T-832 User’s Manual
AMI BIOS Setup Utility
34
3.8 Exit Menu
The Save & Exit menu allows users to load system configuration with optimal or failsafe default values.
Save Changes and Exit
When you have completed the system configuration changes, select this option to leave Setup and reboot the computer so the new system configuration parameters can take effect. Select Save Changes and Exit from the Exit menu and press <Enter>. Select Ok to save changes and exit.
Discard Changes and Exit
Select this option to quit Setup without making any permanent changes to the system configuration. Select Discard Changes and Exit from the Exit menu and press <Enter>. Select Ok to discard changes and exit.
Save Changes and Reset
When you have completed the system configuration changes, select this option to leave Setup and reboot the computer so the new system configuration parameters can take effect. Select Save Changes and Reset from the Save & Exit menu and press <Enter>. Select Yes to save changes and reset.
Discard Changes and Reset
Select this option to quit Setup without making any permanent changes to the system configuration and reboot the computer. Select Discard Changes and Reset from the Save & Exit menu and press <Enter>. Select Yes to discard changes and reset.
Save Changes
When you have completed the system configuration changes, select this option to save changes. Select Save Changes from the Save & Exit menu and press <Enter>. Select yes to save changes.
Page 41
GOT5840T-832 User’s Manual
AMI BIOS Setup Utility
35
Discard Changes
Select this option to quit Setup without making any permanent changes to the system configuration. Select Discard Changes from the Save & Exit menu and press <Enter>. Select Yes to discard changes.
Restore Defaults
It automatically sets all Setup options to a complete set of default settings when you select this option. Select Restore Defaults from the Save & Exit menu and press <Enter>.
Save as User Defaults
Select this option to save system configuration changes done so far as User Defaults. Select Save as User Defaults from the Save & Exit menu and press <Enter>.
Restore User Defaults
It automatically sets all Setup options to a complete set of User Defaults when you select this option. Select Restore User Defaults from the Save & Exit menu and press <Enter>.
Boot Override
Select a drive to immediately boot that device regardless of the current boot order.
NOTE: If you want to use a CF card that capacity is less than 2GB (such as 1GB,
512MB), we recommend you may switch “AHCI mode” to “IDE mode” with "Configure SATA as" of the BIOS setting.
NOTE: And please make sure your Operating System (Ex: Windows Embedded) is installed
with “IDE” driver.
This page is intentionally left blank.
Page 42
GOT5840T-832 User’s Manual
Drivers Installation
36
CHAPTER 4
DRIVERS INSTALLATION
4.1 System
GOT5840T-832 supports Windows7 32-bit and WES 7. To facilitate the installation of system driver, please carefully read the instructions in this chapter before start installing.
1. Insert Driver CD and select the \Drivers.
2. Select all files and follow the installing procedure.
Page 43
GOT5840T-832 User’s Manual
Drivers Installation
37
4.2 Touch Screen
The GOT5840T-832 uses the 5-wire analog resistve. There are the specification and driver installation which are listed below.
4.2.1 Specification
Touch Screen
5-wire Analog Resistive type
Touch Screen Controller
PenMount 6000 USB Touch Screen Controller IC
Communications
USB interface
Baud Rate
19200 baud rate fixed
Resolution
800 x 600 (10 bit A/D converter inside)
Power Input
5V
Power Consumption
Active: 24.6mA / Idle Mode: 13.4mA
4.2.2 Driver Installation- Windows 7
The GOT5840T-832 provides a touch screen driver that users can install it under the operating system Windows 7. To facilitate installation of the touch screen driver, you should read the instructions in this chapter carefully before you attempt installation.
1. Insert Driver CD and follow the path to select the \Drivers\Step 5 - Touch.
2. Follow the installing procedure and press OK.
3. Click Start menu and select “PenMount Utilities”; and then, a PenMount Control Panel pops out.
Page 44
GOT5840T-832 User’s Manual
Drivers Installation
38
4. Select the “Standard Calibrate” tab.
5. Calibration:
To adjust the display with touch panel, click “Calibration” and follow the calibrate point to
do calibration; there are five points on screen for calibration.
6. Press OK.
NOTE: The windows may be out of rang, because the resolution requests 1024x768 or
above when using WIN 7.
NOTE: For the better system performance, please close the Windows AERO or change to
Windows Basic mode.
Page 45
GOT5840T-832 User’s Manual
Drivers Installation
39
4.3 Embedded O.S.
The GOT-5100T provides the WES 7. The O.S. is supported devices which are listed below.
4.3.1 WES 7
Here are supported onboard devices:
Onboard Multi I/O USB CRT/LCD display 10/100/1000 base-T Ethernet Compact Flash Onboard Audio Touch Screen
PenMount Touch screen
Before you can use and calibrate it, here is what you should do:
1. Set up Penmount touch device driver by executing C:\Penmount\ Windows 2000-XP V5.0\setup.exe. When the installation is finished, an icon “PM” appears on the Taskbar.
2. Calibrate Penmount touch by clicking on the “PM” icon, and the go on the calibration
3. Restart the computer.
Please be informed if you use the Windows XP OS, the graphic driver supported by Intel is EMGD, there are three known issues as below:
NOTE: The Intel EMGD package does not include an HDMI audio driver, there will be an
unknown device under device manager.
NOTE: 3D function is not supported.
Windows Embedded Compact 7 (Win CE 7.0)
Here are supported onboard devices:
Onboard Multi I/O USB CRT/LCD display 10/100/1000 base-T Ethernet CompactFlash Onboard Audio Touch Screen
Page 46
GOT5840T-832 User’s Manual
Drivers Installation
40
Calibration Touch screen
In this image we add Penmount Touch drivers and utilities. It is customized for 800 x 600. Calibration:
1. Click “Calibration” on desktop to calibrate touch screen. In the start\programs menu, select “save registry”, thus Calibration data will be saved and effective in next booting.
NOTE: You may switch “AHCI mode” to “IDE mode” with "Configure SATA as" of the BIOS
setting due to Win CE doesnt support AHCI.
Page 47
GOT5840T-832 User’s Manual
Drivers Installation
41
This page is intentionally left blank.
Loading...