Page 1
GOT5103W-845
All-in-One
10.1” WXGA TFT Fanless Touch Panel
Computer with Intel® Celeron® Processor
N3060 onboard
User’s Manual
Page 2
ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third
party’s rights, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make any
commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written permission of Axiomtek Co., Ltd.
CAUTION
If you replace wrong batteries, it causes the danger of explosion. It is recommended by the
manufacturer that you follow the manufacturer’s instructions to only replace the same or
equivalent type of battery, and dispose of used ones.
Copyright 2016 Axiomtek Co., Ltd.
All Rights Reserved
August 2016, Version A3
Printed in Taiwan
Page 3
iii
Safety Precautions
Before getting started, read the following important cautions.
1. Be sure to ground yourself to prevent static charge when installing the internal
components. Use a grounding wrist strap and place all electronic components in any
static-shielded devices. Most electronic components are sensitive to static electrical
charge.
2. Disconnect the power cords from the GOT5103W-845 Series before making any
installation. Be sure both the system and the external devices are turned OFF. Sudden
surge of power could ruin sensitive components. Make sure the GOT5103W-845 Series
is properly grounded.
3. Do not open the system’s top cover. If opening the cover for maintenance is a must, only
a trained technician is allowed to do so. Integrated circuits on computer boards are
sensitive to static electricity. To avoid damaging chips from electrostatic discharge,
observe the following precautions:
Before handling a board or integrated circuit, touch an unpainted portion of the
system unit chassis for a few seconds. This will help to discharge any static
electricity on your body.
When handling boards and components, wear a wrist-grounding strap, available
from most electronic component stores.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
Windows® is a trademark of Microsoft Corporation.
IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation.
Intel® and Pentium® are trademarks of Intel Corporation.
AMI is trademark of American Megatrend Inc.
Other brand names and trademarks are the properties and registered brands of their
respective owners.
Page 4
iv
Table of Contents
Disclaimers ..................................................................................................... ii
Safety Precautions ........................................................................................ iii
Chapter 1 Introduction ............................................. 1
1.1 General Description ............................................................................ 2
1.2 Specifications ...................................................................................... 3
1.3 Dimensions .......................................................................................... 5
1.4 I/O Outlets ............................................................................................ 6
1.5 Packing List ......................................................................................... 8
Chapter 2 Hardware and Installation ...................... 9
2.1 SBC87845 Jumpers and Connectors............................................... 10
2.1.1 Jumper Settings ........................................................................................ 12
2.1.2 Connectors ................................................................................................ 13
2.2 Ethernet .............................................................................................. 18
2.3 Mountings –Panel/Wall/Desktop/VESA ........................................... 19
2.3.1 Panel-Mounting ......................................................................................... 19
2.3.2 VESA-ARM/Wall-Mount ............................................................................ 20
2.4 Half-slim SSD Installation ................................................................. 21
2.5 DRAM Installation .............................................................................. 23
2.6 Mini Card Installation ........................................................................ 25
2.6.1 Wireless LAN Card Installation ................................................................. 25
2.6.2 mSATA Card Installation ............................................................................ 27
2.7 Power Input (Phoenix type) .............................................................. 28
Chapter 3 AMI BIOS Setup Utility .......................... 29
3.1 Navigation Keys ................................................................................ 29
3.2 Main Menu .......................................................................................... 30
3.3 Advanced Menu ................................................................................. 31
3.4 Chipset Menu ..................................................................................... 38
3.5 Security .............................................................................................. 40
3.6 Boot Menu .......................................................................................... 41
3.7 Save & Exit ......................................................................................... 42
Chapter 4 Drivers Installation .............................. 43
Page 5
v
4.1 System ............................................................................................... 43
4.1.1 Windows 7, 8.X, 10 ................................................................................... 43
4.2 Touch Screen ................................................................ ..................... 44
4.2.1 Specification .............................................................................................. 44
4.2.2 Driver Installation- Windows 7/8.X/10 ....................................................... 44
4.3 Embedded O.S. .................................................................................. 45
4.3.1 WES 7 & WE8S ......................................................................................... 45
Appendix A Watchdog Timer &DIO Programming .... 47
About Watchdog Timer ................................................................................ 47
How to Use Watchdog Timer ....................................................................... 47
WDT Sample Program ................................................................................. 48
How to Use DIO Software Programming .................................................... 49
Appendix B Volume Control .................................... 51
About Volume Control ................................................................................. 51
How to Use Volume Control ........................................................................ 51
Removed Volume Control Tool ................................................................... 58
Page 6
vi
This page is intentionally left blank.
Page 7
GOT5103W-845 User ’s Manual
Introduction 1
Chapter 1
Introduction
This chapter contains general information and detailed specifications of the GOT5103W-845.
Chapter 1 includes the following sections:
General Description
Specifications
Dimensions
I/O Outlets
Package List
Page 8
GOT5103W-845 User’s Manual
2 Introduction
1.1 General Description
The GOT5103W-845 is a fan-less and compact-size touch panel computer, equipped with a
10.1” TFT LCD display, project capacitive multi-touch and low power consumption Intel®
Celeron® Processor N3060 (2M Cache, up to 2.48 GHz). The GOT5103W-845 supports
Windows 7, Windows 8.x, Windows 10 and Windows embedded OS. The panel computer is
able to install a mSATA and an optional half-slim SSD, provides two Mini card slots for
wireless module. Its excellent ID and friendly user interface make it a professional yet
easy-to-use panel computer. The GOT5103W-845 is an ideal for space-limited applications in
factory automation, machine maker operating systems, building automation, and more.
GOT5103W-845: 10.1” TFT WXGA Fanless Touch Panel Computer
Reliable and Stable Design
The GOT5103W-845 adopts a fanless cooling system and a mSATA, which makes it
suitable for vibration environments.
Embedded O.S. Supported
The GOT5103W-845 not only supports Windows 7, Windows 8.x and Windows 10, but
also supports embedded OS,. For storage device, the GOT5103W-845 supports an
optional half –slim SSD device and a mSATA.
Industrial-grade Product Design
The GOT5103W-845 has an incredible design to be used in different industrial
environments.
The front bezel meets the IP65 standard.
For connecting other devices, the GOT5103W-845 also features several interfaces: USB,
Ethernet, and RS-232/422/485.
Page 9
GOT5103W-845 User ’s Manual
Introduction 3
1.2 Specifications
Main CPU Board
CPU
Intel® Celeron® Processor N3060 (2M Cache, up to 2.48 GHz) onboard.
System Memory
One 204-pin DDR3L SO-DIMM socket
Maximum memory up to 8BG
BIOS
America Megatrends BIOS
I/O System
Standard I/O
one RSS-232/422/485
one RS-232
Two USB 2.0
Two USB 3.0
One HDMI
Ethernet
2x RJ45 Giga Ethernet (Intel i211AT)
Audio
One Line out
Two Internal 2W speaker
Expansion
1 x Mini-card slot (w/SIM slot)
1 x Mini-card slot (supports mSATA, optional)
Storage
One mSATA
One half-slim SSD
Power connector
GOT5103W-845-PCT-J: 12VDC w/external 60W AC Adapter with screw type
connector or
GOT5103W-845-PCT-24VDC : 24VDC with phoenix power connector or
Page 10
GOT5103W-845 User’s Manual
4 Introduction
System Specification
10.1” WXGA(1289x800) LCD with LED backlight
Project capacitive multi-touch
Fanless Heat Dispensing Design
Disk drive housing:
One half-slim SSD(optional)
One mSATA
Net Weight
1.08 Kgs (2.38 lb)
Dimension (Main Body Size)
260.8 mm (10.27") (W) x 38 mm (1.50" (D) x 194.1 mm (7.65") (H)
Operation Temperature
0℃ to 50℃
Relative Humidity
10% to 90% @ 40℃, Non-Condensing
Vibration
2.0G, 5 to 500 Hz, 2.0 G random for SSD
Power input
24VDC with phoenix power connector or
External 60W AC Adapter
— Power Input: 100VAC to 240VAC
— Power Output: 12VDC, Max. 5A
NOTE All specifications and images are subject to change without notice.
NOTE If the operation temperature is higher than 35℃, the wide temperature
HDD is recommended to be used on the device.
Page 11
GOT5103W-845 User ’s Manual
Introduction 5
1.3 Dimensions
This diagram shows you dimensions and outlines of the GOT5103W-845.
Page 12
GOT5103W-845 User’s Manual
6 Introduction
1.4 I/O Outlets
Please refer to the following illustration for I/O locations of the GOT5103W-845.
No
Function
No
Function
1
POWER SWITCH (ATX)
7
COM 2(RS-232)
2
Power Input connector (Phoenix)
8
HDMI
3
Power Input connector (Screw)
9
USB 3.0 x 2
4
USB 2.0 x 2
10
Ethernet x 2
5
Audio (Line-out)
11
AT(right) / ATX(left) switch
6
COM 1(RS-232/422/485)
12
Speaker
Page 13
GOT5103W-845 User ’s Manual
Introduction 7
No
Function
No
Function
1
Power LED
orange: display off
green : display on
4
Display on/off
2
HDD LED
5
Volume -/+
3
Brightness -/+
6
Mic in
NOTE The volume control function only can be performed under the windows
operation system with AXIOMTEK volumeSYNC program.
Page 14
GOT5103W-845 User’s Manual
8 Introduction
1.5 Packing List
When you receive the GOT5103W-845, the bundled package should contain the following
items:
GOT5103W-845 x 1
Driver CD x 1
Phoenix connector x1 (for GOT5103W-845-DC and GOT5103W-845-24VDC)
Power Adapter & power cord (for GOT5103W-845-J)
If you can not find the package or any items are missing, please contact Axiomtek distributors
immediately.
Page 15
GOT5103W-845 User ’s Manual
Hardware and Installation 9
Chapter 2
Hardware and Installation
The GOT5103W-845 provides rich I/O ports and flexible expansions for you to meet different
demand. The chapter will show you how to install the hardware. It includes:
SBC87845 Jumpers and Connectors
Ethernet
Mounting Way
Hard disk
DRAM
Wireless LAN Card
Power Input
Page 16
GOT5103W-845 User’s Manual
10 Hardware and Installation
2.1 SBC87845 Jumpers and Connectors
Component Side
Page 17
GOT5103W-845 User ’s Manual
Hardware and Installation 11
Solder Side
Page 18
GOT5103W-845 User’s Manual
12 Hardware and Installation
2.1.1 Jumper Settings
Making the proper jumper settings configure the SBC87845 to match the needs of your
application.
The following table shows the default jumper settings for the onboard devices.
Jumper
★ Default Setting
Jumper Setting
JP1
★ OSD function: LCD ON/OFF
OSD function: Touch ON/OFF
Short 1-2
Short 2-3
JP2
★ LVDS Panel Power : 3.3V
LVDS Panel Power : 5V
Short 1-2
Short 2-3
JP3
★ ATX mode
AT mode
Short 1-2
Short 2-3
JP5
Touch Controller 4,8 WIRE
★ Touch Controller 5 WIRE
Short 1-2
Short 2-3
JP6
★ Normal
Clear CMOS
Short 1-2
Short 2-3
JP7
★ Internal Buzzer enable
Internal Buzzer disable
Short 1-2
Short 2-3
JP8
★ COM1 normal mode
COM1 pin1 with power :+5V
COM1 pin9 with power :+12V
Short 3-5,4-6
Short 1-3,4-6
Short 3-5,2-4
Page 19
GOT5103W-845 User ’s Manual
Hardware and Installation 13
2.1.2 Connectors
The connectors allow the CPU Board to connect with other parts of the system. Ensure that all
connectors are in place and firmly attached. The following table lists the function of each
connector on the SBC87845
Connectors
Label
LVDS inverter connector
CN1
LVDS connector
CN2
SATA connector
CN3
OSD connector
CN4
HDD power connector
CN6
Full size min-PCIe connector
CN7,CN11
SIM card connector
CN8
DIO connector
CN9
Power connector
CN10
Power Button connector
CN12
Touch connector
CN13
LIN/MIC In connector
CN16
Speaker Out connector
CN17
System Fan connector
CN18
USB2.0 connector
CN19
RJ45 connector
CN20,CN22
USB3.0 connector
CN21
HDMI connector
CN23
Audio out connector
CN24
RS232/422/485 Port connector
CN25,CN27
RS232 Port connector
CN26
+5V Standby Power connector
CN28,CN29
LVDS inverter connector: CN1
Pin
Description
Pin
Description
1
GND
5
Inverter ON-OFF
2
GND
6
+12V
3
GND
7
+12V
4
Backlight control
8
+12V
Page 20
GOT5103W-845 User’s Manual
14 Hardware and Installation
LVDS connector: CN2
Pin Assignment
OSD connector: CN4
Pin
Description
Pin
Description
1
VCC
21
GND
2
VCC
22
GND
3
VCC
23
LVDSA_DATAN0
4
VCC
24
LVDSB_DATAN2
5
VCC
25
LVDSA_DATAP0
6
VCC
26
LVDSB_DATAP2
7
Resolution selection[0]
27
GND
8
Resolution selection[1]
28
GND
9
GND
29
LVDSA_DATAN1
10
GND
30
LVDSA_DATAN3
11
LVDSB_DATAN3
31
LVDSA_DATAP1
12
LVDSB_DATAN0
32
LVDSA_DATAP3
13
LVDSB_DATAP3
33
GND
14
LVDSB_DATAP0
34
GND
15
GND
35
LVDSA_DATAN2
16
GND
36
LVDSA_CLKN
17
LVDSB_CLKN
37
LVDSA_DATAP2
18
LVDSB_DATAN1
38
LVDSA_CLKP
19
LVDSB_CLKP
39
Resolution selection[2]
20
LVDSB_DATAP1
40
Resolution selection[3]
Pin
Description
1
Brightness+
2
Brightness-
3
volume+
4
Volume-
5
Touch or LCD ON/OFF
6
POWER LED
7
SATA LED
8
Touch LED
9
BackLight LED
10
GND
Page 21
GOT5103W-845 User ’s Manual
Hardware and Installation 15
HDD power connector: CN6
SIM card connector: CN8
DIO connector: CN9
Pin
Description
1
+12V
2
GND
3
GND
4
+5V
Pin
Description
Pin
Description
1
UIM PWR
5
GND
2
UIM RST
6
UIM VPP
3
UIM CLK
7
UIM DATA
4
NC 8 NC
Pin
Description
1
GPIO0
2
GPIO1
3
GPIO2
4
GPIO3
5
GPIO4
6
GND
7
GPIO5
8
GPIO6
9
+3.3V
10
GPIO7
Page 22
GOT5103W-845 User’s Manual
16 Hardware and Installation
Power connector: CN10
Power button connector: CN12
Pin
Description
Pin
Description
1
GND
2
PWBTN
TOUCH connector: CN13
Pin
Description
1
Sense
2
X+ 3 X- 4 Y+ 5 Y-
Lin/Mic In connector: CN16
Pin
Description
Pin
Description
1
LIN IN R
2
GND
3
LIN IN L
4
GND
5
MIC IN
6
GND
Speaker connector: CN17
Pin
Description
1
SPKOUT_L-
2
SPKOUT_L+
3
SPKOUT_R-
4
SPKOUT_R+
5
GND
Pin
Description
1
DCIN (+12V)
2
DCIN (+12V)
3
GND
4
GND
Page 23
GOT5103W-845 User ’s Manual
Hardware and Installation 17
System Fan connector: CN18
Pin
Description
1
GND
2
+12V / Speed control output
3
Fan speed detect
USB2.0 connector: CN19
Pin
Description
Pin
Description
1
+5V 2 +5V
3
USB-
4
USB-
5
USB+
6
USB+
7
GND
8
GND
9
GND
10
GND
+5V Standby Power connector: CN28, CN29
Pin
Description
Pin
Description
1
GND
2
+5V_SBY
COM port Connector
The pin assignment of RS-232/RS-422/RS-485 is listed on the following table.
Pin
RS-232
RS-422
RS-485
1
DCD
TX-
Data-
2
RXD
TX+
Data+
3
TXD
RX+
No use
4
DTR
RX-
No use
5
GND
GND
GND
6
DSR
No use
No use
7
RTS
No use
No use
8
CTS
No use
No use
9
RI
No use
No use
Page 24
GOT5103W-845 User’s Manual
18 Hardware and Installation
2.2 Ethernet
The GOT5103W-845 is equipped with two high performance Plug and Play Ethernet interfaces,
full compliant with IEEE 802.3 standard, and can be connected with a RJ-45 LAN connector.
Please refer to detailed pin assignment list below:
Pin
Signal
1234567
8
RJ-45
1
TX+ (Data transmission positive
2
TX- (Data transmission negative)
3
Rx+(Data reception positive)
4
RJ45 termination
5
RJ45 termination
6
Rx- (Data reception negative)
7
RJ45 termination
8
RJ45 termination
Page 25
GOT5103W-845 User ’s Manual
Hardware and Installation 19
2.3 Mountings –Panel/Wall/Desktop/VESA
There are several mounting ways for the GOT5103W-845, Wall, Desktop , VESA and panel
mountings.
2.3.1 Panel-Mounting
The GOT5103W-845 is designed for panel mount application. A set of standard mounting kit
are bundled with the system package that you can use it to mount the GOT5103W-845.
Step1 Sticks 4 sealing pads on the edges of chassis.
Step2 Assemble the panel kit to the chassis, and fix the screws.
Page 26
GOT5103W-845 User’s Manual
20 Hardware and Installation
2.3.2 VESA-ARM/Wall-Mount
The GOT5103W-845 provides VESA mount: 75x75 mm. Screw four screws to fix the kit in the
back chassis.
Step1 Find out the screws as marked on the back side of chassis.
Step2 Assemble the VESA bracekt to the back side of the chassis, and fix the
screws.
Step 3 VESA mounting Installation completed.
Page 27
GOT5103W-845 User ’s Manual
Hardware and Installation 21
2.4 Half-slim SSD Installation
The GOT5103W-845 provides an optional half-slim SSD for users to install. Please refer to the
following instructions for installation:
Step 1 Turn off the system, and unplug the power cord.
Step 2 Remove the back cover.
Step 3 Screw half-slim SSD bracket into the system.
Page 28
GOT5103W-845 User’s Manual
22 Hardware and Installation
Step 4 Plug the data and power cable to half-slim SSD. Screws the half-slim SSD into
the system, and Installation complete.
Page 29
GOT5103W-845 User ’s Manual
Hardware and Installation 23
2.5 DRAM Installation
The GOT5103W-845 provides one 204-pin DDR3L SODIMM socket that support system
memory up to 8GB. Please follow steps below to install the memory modules:
Step 1 Open the back cover and find out the DIMM socket on main board(SBC87845).
Step 2 Insert the DRAM to the DIMM socket, and then push it down firmly until it is
clipped by the socket.
Page 30
GOT5103W-845 User’s Manual
24 Hardware and Installation
Step 3 Install the memory module into the socket and push it firmly down until it is
fully seated. The socket latches are levered upwards and clipped on to the
edges of the DIMM.
Page 31
GOT5103W-845 User ’s Manual
Hardware and Installation 25
2.6 Mini Card Installation
2.6.1 Wireless LAN Card Installation
The GOT5103W-845 provides two Mini card slots for user to install wireless LAN cards. You
can choose either slot 1 or slot 2 to install the wireless LAN card and refer to the following
instructions and illustration:
Step 1 Open the back cover and find out the mini-card slot on main board.
Step 2 Insert the wireless LAN card to the slot. Screw it firmly on the slot.
Page 32
GOT5103W-845 User’s Manual
26 Hardware and Installation
Step 3 Sticks antenna cables on the chassis as below.
Step 4 There are two connectors on wireless LAN card. One is MAIN, and the other is
Secondary. Connect antenna cable to MAIN connector on wireless LAN card.
Page 33
GOT5103W-845 User ’s Manual
Hardware and Installation 27
2.6.2 mSATA Card Installation
The GOT5103W-845 provides one Mini card slot for user to install mSATA. Please choose the
slot 2 when installing the mSATA card and refer to the following instructions and illustration:
Step 1 Open the back cover and find out the mini-card slot on main board.
Step 2 Insert the mSATA card to the slot 2. Screw it firmly on the slot.
Page 34
GOT5103W-845 User’s Manual
28 Hardware and Installation
2.7 Power Input (Phoenix type)
GOT5103W-845 equips with a phoenix type power connector. It adopts 24VDC. Please follow
the signs on power connector to connect DC power source.
+: Power positive －:Power negative
NOTE The safety ground must be connected to ensure the unit working appropriately.
Page 35
GOT5103W-845 User ’s Manual
AMI BIOS Setup Utility 29
Chapter 3
AMI BIOS Setup Utility
This chapter provides users with detailed description how to set up basic system configuration
through the AMIBIOS8 BIOS setup utility.
3.1 Navigation Keys
The BIOS setup/utility uses a key-based navigation system called hot keys. Most of the BIOS
setup utility hot keys can be used at any time during the setup navigation process.
These keys include <F1>, <F2>, <F3>, <F4>, <Enter>, <ESC>, <Arrow> keys, and so on.
NOTE Some of navigation keys differ from one screen to another.
Left/Right
The Left and Right <Arrow> keys allow you to select a setup screen.
Up/Down
The Up and Down <Arrow> keys allow you to select a setup screen or sub-screen.
+ Plus/Minus
The Plus and Minus <Arrow> keys allow you to change the field value of a
particular setup item.
Tab
The <Tab> key allows you to select setup fields.
F1
The <F1> key allows you to display the General Help screen.
F2
The <F2> key allows you to load previous value
F3
The <F3> key allows you to Load Optimized Defaults.
F4
The <F4> key allows you to save any changes you have made and exit Setup.
Press the <F4> key to save your changes.
Esc
The <Esc> key allows you to discard any changes you have made and exit the
Setup. Press the
<Esc> key to exit the setup without saving your changes.
Enter
The <Enter> key allows you to display or change the setup option listed for a
particular setup item. The <Enter> key can also allow you to display the setup subscreens.
Page 36
GOT5103W-845 User’s Manual
30 AMI BIOS Setup Utility
3.2 Main Menu
System Time/Date
Use this option to change the system time and date. Highlight System Time or System Date
using the <Arrow> keys. Enter new values through the keyboard. Press the <Tab> key or the
<Arrow> keys to move between fields. The date must be entered in MM/DD/YY format. The
time is entered in HH:MM:SS format.
Page 37
GOT5103W-845 User ’s Manual
AMI BIOS Setup Utility 31
3.3 Advanced Menu
The Advanced menu allows users to set configuration of the CPU and other system devices.
You can select any of the items in the left frame of the screen to go to the sub menus:
NCT6106D Super IO Configuration
Hardware Monitor
ACPI Settings
CPU Configuration
SATA Configuration
USB Configuration
Utility Configuration
PCIE/mSATA Mini Card Configuration
For items marked with “”, please press <Enter> for more options.
Page 38
GOT5103W-845 User’s Manual
32 AMI BIOS Setup Utility
NCT6106D Super IO Configuration
Use this screen to select options for the Super IO Configuration, and change the value of the
selected option
Page 39
GOT5103W-845 User ’s Manual
AMI BIOS Setup Utility 33
Serial Port 1-2 configuration
1. Serial port:
This option used to enable or disable the serial port.
2. Device Setting:
This item specifies the base I/O port address and Interrupt Request address of serial port.
The port 1 Optimal setting is 3F8/IRQ4.
The port 2 Optimal setting is 2E8/IRQ3.
3. Serial type:
This option used to select RS232/422/485 function.
Page 40
GOT5103W-845 User’s Manual
34 AMI BIOS Setup Utility
Hardware Monitor
This screen shows the Hardware Health Status in real time.
ACPI Settings
You can use this screen to select options for the ACPI Configuration, and change the value of
the selected option. A description of the selected item appears on the right side of the screen.
ACPI Sleep State
Allow you to select the Advanced Configuration and Power Interface (ACPI) state to be used
for system suspend. Here are the options for your selection, Suspend disable and S3
(Suspend to RAM).
Page 41
GOT5103W-845 User ’s Manual
AMI BIOS Setup Utility 35
CPU Configuration
This screen shows the CPU Configuration and intel virtualization technology enable/disable
selected.
SATA Configuration
You can use this screen to select options for the SATA Configuration, and change the value of
the selected option.
SATA Controller
Use this item to choose the SATA Controller. Here are the options for your selection, Enable,
Disable.
Page 42
GOT5103W-845 User’s Manual
36 AMI BIOS Setup Utility
USB Configuration
This screen shows the USB Configuration.
Utility Configuration
This screen shows the Utility Configuration.
Page 43
GOT5103W-845 User ’s Manual
AMI BIOS Setup Utility 37
PCIE/mSATA Mini Card Configuration
This screen shows the PCIE/mSATA Mini Card Configuration. Here are the options for your
selection, PCIE, mSATA.
Page 44
GOT5103W-845 User’s Manual
38 AMI BIOS Setup Utility
3.4 Chipset Menu
The Chipset menu gives the North Bridge memory information and South Bridge TXE
information.
North Bridge
This screen shows the North Bridge memory information.
Page 45
GOT5103W-845 User ’s Manual
AMI BIOS Setup Utility 39
South Bridge
This screen shows the South Bridge TXE information.
Page 46
GOT5103W-845 User’s Manual
40 AMI BIOS Setup Utility
3.5 Security
Page 47
GOT5103W-845 User ’s Manual
AMI BIOS Setup Utility 41
3.6 Boot Menu
The Boot menu allows users to change boot options of the system. You can select any of the
items in the left frame of the screen to go to the sub menus:
Setup Prompt Timeout
Set the Timeout for wait press key to enter Setup Menu
Bootup NumLock State
Use this item to select the power-on state for the NumLock. The default setting is on.
Quiet Boot
Use this item to enable or disable the Quite Boot state. The default setting is disable.
PXE ROM
Use this item to enable or disable the Preboot Execution Environment. The default setting is
disable.
Boot Option Priorities
Specifies the overall boot order from the available devices.
Page 48
GOT5103W-845 User’s Manual
42 AMI BIOS Setup Utility
3.7 Save & Exit
Page 49
GOT5103W-845 User ’s Manual
Drivers Installation 43
Chapter 4
Drivers Installation
4.1 System
GOT5103W-845 supports Windows 7, Windows 8.1, Windows 10 ,WES 7 and WE8S. To
facilitate the installation of system driver, please carefully read the instructions in this chapter
before start installing.
4.1.1 Windows 7, 8.X, 10
1. Insert Driver CD and select the “\Drivers”.
2. Select all files and follow the installing procedure.
Page 50
GOT5103W-845 User’s Manual
44 Drivers Installation
4.2 Touch Screen
The GOT5103W-845 usesr projected capacitive multi-touch . There are the specification and
driver installation which are listed below.
It also can drive the touch panel to get ten fingers touch function that based on the Windows 7
support.
4.2.1 Specification
Touch Screen
Projected capacitive multi-touch
Touch Control Board
COF
Communications
USB interface
Power Supply
5V
Power Consumption
40mA
Input Method
Finger or Cap.Stylus
Resolution
25ppi(Min.)
Note: Base on WIN7 definition, ppi(Pixcel per inch)
Win7 USB Driver
Non-Driver
Calibration
Non-Calibration
NOTE The projected capacitive multi-touch can drive the touch panel to get ten fingers
touch function that based on the Windows 7 & Windows 8.x support.
4.2.2 Driver Installation- Windows 7/8.X/10
The GOT5103W-845 (resistive touch model )provides a touch screen driver that users can
install it under the operating system Windows 7/8.x/10. To facilitate installation of the touch
screen driver, you should read the instructions in this chapter carefully before you attempt
installation.
1. Insert Driver CD and follow the path to select the “\Drivers\Step 8 – Penmount Touch
driver
”.
Page 51
GOT5103W-845 User ’s Manual
Drivers Installation 45
2. Follow the installing procedure and press OK.
4.3 Embedded O.S.
The GOT5103W-845 provides the WES 7 and WE8S Embedded. The O.S. is supported
devices which are listed below.
4.3.1 WES 7 & WE8S
Here are supported onboard devices:
Onboard Multi I/O
Half-Sim SATA HDD
USB
CRT/LCD display
10/100/1000 base-T Ethernet
mSATA
Onboard Audio
Touch Screen
Page 52
GOT5103W-845 User’s Manual
46 Drivers Installation
This page is intentionally left blank.
Page 53
GOT5103W-845 User ’s Manual
Watchdog Timer 47
Appendix A
Watchdog Timer &DIO Programming
About Watchdog Timer
Software stability is major issue in most application. Some embedded systems are not
watched by human for 24 hours. It is usually too slow to wait for someone to reboot when
computer hangs. The systems need to be able to reset automatically when things go wrong.
The watchdog timer gives us solution.
The watchdog timer is a counter that triggers a system reset when it counts down to zero from
a preset value. The software starts counter with an initial value and must reset it periodically. If
the counter ever reaches zero which means the software has crashed, the system will reboot.
How to Use Watchdog Timer
The I/O port base addresses of watchdog timer are 2E (hex) and 2F (hex). The 2E (hex) and
2F (hex) are address and data port respectively.
Assume that program A is put in a loop that must execute at least once every 10ms. Initialize
watchdog timer with a value bigger than 10ms. If the software has no problems; watchdog
timer will never expire because software will always restart the counter before it reaches zero.
Begin
Enable and Initialize
Watchdog Timer
Program “A”
Disable Watchdog
Timer
Next
Next
Next
Next
Begin
Enable and Initialize
Watchdog Timer
Program “A”
Reset Watchdog
Timer
Next
Next
Next
Next
Page 54
GOT5103W-845 User’s Manual
48 Watchdog Timer
WDT Sample Program
Enable WDT
1.Enable configuration
-O 2E 87
-O 2E 87
2. Select Logic device:
-O 2E 07
-O 2F 08
3. WDT Device Enable
-O 2E 30
-O 2F 01
4. Set timer unit
-O 2E F0
-O 2F 00 (00: Sec; 08: Minute)
5. Set base timer:
-O 2E F1
-O 2F 0A Set Reset Time (Ex.0A:10 Sec)
Disable WDT
1.Enable configuration
-O 2E 87
-O 2E 87
2. Select Logic device:
-O 2E 07
-O 2F 08
3. WDT Device Disable
-O 2E 30
-O 2F 00
Page 55
GOT5103W-845 User ’s Manual
Watchdog Timer 49
How to Use DIO Software Programming
Digital I/O Software Programming
I2C to GPIO PCA9554
I2C address: 0b01000000.
Page 56
GOT5103W-845 User’s Manual
50 Watchdog Timer
Page 57
GOT5103W-845 User ’s Manual
Volume Control 51
Appendix B
Volume Control
About Volume Control
Axiomtek offers the volume control tool under Windows 7 Windows 8 and Windows 10, people
can adjust the system volume depending on your personal taste and the amount of ambient
volume in the room after installing the volume control tool.
How to Use Volume Control
Step 1 According to the OS version, please insert the driver CD and follow the
path to select the proper driver, Driver\Step 7 – VolumeSync”
Page 58
GOT5103W-845 User’s Manual
52 Volume Control
Page 59
GOT5103W-845 User ’s Manual
Volume Control 53
Page 60
GOT5103W-845 User’s Manual
54 Volume Control
Page 61
GOT5103W-845 User ’s Manual
Volume Control 55
Page 62
GOT5103W-845 User’s Manual
56 Volume Control
Step 2 System auto reboot, installation completed.
Page 63
GOT5103W-845 User ’s Manual
Volume Control 57
Step 3 Select “△” icon then finding out the “Axiomtek” to ensure the volume driver
is installed appropriately.
Step 4 How to use the Volume Control
Select volume +- to adjust the system volume.
Page 64
GOT5103W-845 User’s Manual
58 Volume Control
Removed Volume Control Tool
Step 1 Go to Control Panel -> Programs -> Programs and Features. Select Uninstall
on AxAVC_Setup.
Page 65
GOT5103W-845 User ’s Manual
Volume Control 59
Step 2 Follow the procedures and press “Close”.
Page 66
GOT5103W-845 User’s Manual
60 Volume Control
Step 3 System auto reboot, uninstallation completed.
Loading...