AXIOMTEK GOT5100T-832, GOT5120T-832 User Manual

GOT5100T-832

All-in-One

10.4” SVGA TFT Fanless Touch Panel Computer with
Intel® AtomTM N2600 Processor Onboard

User’s Manual

ii

Disclaimers

This manual has been carefully checked and believed to contain accurate information. Axiomtek
Co., Ltd. assumes no responsibility for any infringements of patents or any third party’s rights, and
any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make any
commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time without
notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted, in any
form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the
prior written permission of Axiomtek Co., Ltd.

Copyright 2012 Axiomtek Co., Ltd.

All Rights Reserved
Sep.2012, Version A1
Printed in Taiwan

iii

Safety Precautions

Before getting started, please read the following important safety precautions.

1. The GOT5100T-832 does not come equipped with an operating system. An operating

system must be loaded first before installing any software into the computer.

2. Be sure to ground yourself to prevent static charge when installing the internal

components. Use a grounding wrist strap and place all electronic components in any
static-shielded devices. Most electronic components are sensitive to static electrical
charge.

3. Disconnect the power cord from the GOT5100T-832 before any installation. Be sure both

the system and external devices are turned OFF. A sudden surge of power could ruin
sensitive components that the GOT5100T-832 must be properly grounded.

4. The brightness of the flat panel display will be getting weaker as a result of frequent

usage. However, the operating period varies depending on the application environment.

5. Turn OFF the system power before cleaning. Clean the system using a cloth only. Do not

spray any liquid cleaner directly onto the screen. The GOT5100T-832 comes with a
touchscreen. Although the touchscreen is chemical resistant, it is recommended that you
spray the liquid cleaner on a cloth first before wiping the screen. In case your system
comes without the touchscreen, you must follow the same procedure and not spray any
cleaner on the flat panel directly.

6. Avoid using sharp objects to operate the touchscreen. Scratches on the touchscreen

may cause malfunction or internal failure to the touchscreen.

7. The flat panel display is not susceptible to shock or vibration. When assembling the

GOT5100T-832, make sure it is securely installed.

8. Do not open the system’s back cover. If opening the cover for maintenance is a must,

only a trained technician is allowed to do so. Integrated circuits on computer boards are
sensitive to static electricity. To avoid damaging chips from electrostatic discharge,
observe the following precautions:

 Before handling a board or integrated circuit, touch an unpainted portion of the

system unit chassis for a few seconds. This will help to discharge any static
electricity on your body.

 When handling boards and components, wear a wrist-grounding strap, available

from most electronic component stores.

Trademarks Acknowledgments

Axiomtek is a trademark of Axiomtek Co., Ltd.
IBM, PC/AT, PS/2, VGA are trademarks of International
Business Machines Corporation.

Intel® and Atom™ are registered trademarks of Intel Corporation.
MS-DOS, Microsoft C and Quick BASIC are trademarks of Microsoft Corporation.
VIA is a trademark of VIA Technologies, Inc.
SST is a trademark of Silicon Storage Technology, Inc.
UMC is a trademark of United Microelectronics Corporation.
Other brand names and trademarks are the properties and registered brands of their respective
owners.

iv

Table of Contents

Disclaimers .................................................................................................................................. ii

Safety Precautions ...................................................................................................................... iii

CHAPTER 1 INTRODUCTION ........................................................................................................ 1

1.1 General Description ................................................................................................... 1

1.2 Specifications ............................................................................................................. 2

1.2.1 Main CPU Board ........................................................................................................ 2

1.2.2 I/O System ................................................................................................................. 2

1.2.3 System Specification .................................................................................................. 3

1.3 Dimensions ................................................................................................................ 4

1.4 I/O Outlets .................................................................................................................. 6

1.5 Packing List ................................................................................................................ 7

CHAPTER 2 HARDWARE INSTALLATION ................................................................................... 9

2.1 CF card Installation .................................................................................................... 9

2.2 Serial Ports Interface ............................................................................................... 10

2.2.1 COM1&COM2 Connector ........................................................................................ 11

2.3 Ethernet ................................................................................................................... 12

2.4 Mountings – Panel/Wall/Desktop/VESA .................................................................. 13

2.4.1 Panel Mounting ........................................................................................................ 13

2.4.2 Wall-Mounting .......................................................................................................... 14

2.4.3 Desktop-Mounting .................................................................................................... 14

2.4.4 VESA-ARM Mounting............................................................................................... 16

2.5 HDD Installation ....................................................................................................... 18

2.6 DRAM Installation .................................................................................................... 20

2.7 Wireless LAN Card Installation ................................................................................ 22

CHAPTER 3 AMI BIOS SETUP UTILITY ..................................................................................... 25

3.1 Starting ..................................................................................................................... 25

3.2 Navigation Keys ....................................................................................................... 26

3.3 Main Menu ............................................................................................................... 27

3.4 Advanced Menu ....................................................................................................... 28

3.5 Chipset Menu ........................................................................................................... 35

3.6 Boot Menu ................................................................................................................ 37

3.7 Security Menu .......................................................................................................... 38

3.8 Exit Menu ................................................................................................................. 39

CHAPTER 4 DRIVERS INSTALLATION ...................................................................................... 41

4.1 System ..................................................................................................................... 41

4.2 Touch Screen ........................................................................................................... 42

4.2.1 Specification ............................................................................................................. 42

4.2.2 Driver Installation- Windows 7 ................................................................................. 42

4.3 Embedded O.S. ....................................................................................................... 45

4.3.1 WES 7 ...................................................................................................................... 45

4.3.2 Windows CE.NET 6.0 .............................................................................................. 45

GOT-5100T User’s Manual

1

CHAPTER 1

INTRODUCTION

This chapter contains general information and detailed specifications of the GOT5100T-832.
Chapter 1 includes the following sections:

 General Description
 Specification
 Dimensions
 I/O Outlets
 Package List

1.1 General Description

The GOT5100T-832 is a fan-less and compact-size touch panel computer, equipped with a 10.4”
TFT LCD display and low power consumption Intel○R AtomTM N2600 1.6GHz processor with FSB
533MHz. The GOT5100T-832 supports Windows® 7 32-bit,, WES 7. The panel computer
provides a Mini card slot for wireless module. Its excellent ID and friendly user interface make it a
professional yet easy-to-use panel computer. The GOT5100T-832 is an ideal for space-limited
applications in factory automation, machine maker operating systems, building automation, and
more.

 GOT5100T-832: 10.4” TFT SVGA Fanless Touch Panel Computer

 Reliable and Stable Design

The GOT5100T-832 adopts a fanless cooling system, which makes it suitable for
vibration environments.

 Embedded O.S. Supported

The GOT5100T-832 not only supports Windows® 7 32-bit, but also supports embedded
OS, such as WES 7. For storage device, the GOT5100T-832 supports
CompactFlash™ card(optional) and 2.5” SATA device.

 Industrial-grade Product Design

The GOT5100T-832 has an incredible design to be used in different industrial
environments.

 The front bezel meets the IP65/NEMA4 standard.

For connecting other devices, the GOT5100T-832 also features several interfaces: USB,
Ethernet, and RS-232/422/485.

Introduction

GOT5100T-832 User’s Manual

2

1.2 Specifications

1.2.1 Main CPU Board

 CPU

 Intel

 System Chipset

 Intel

 BIOS

 America Megatrends BIOS

 System Memory

 One 204-pin DDR3 800MHz SO-DIMM socket
 Maximum memory up to 2GB

○R

AtomTM N2600 1.6GHz processor onboard

○R

NM10 Express

1.2.2 I/O System

 Standard I/O

 1x RS-232/422/485, 1x RS232

4x USB 2.0

 Ethernet

 2x 10/100/1000Mbps Ethernet

 Audio

 One Line-out

 Expansion

 1 x PCIe mini card(optional)

 Storage

 One 2.5” SATA HDD
 One slot for CompactFlash™ (optional)

 Power connector

 GOT5100T-832 : DC power 10~30VDC (phoenix type)
 GOT5100T-832-J : AC 100~240V to DC 12V adapter(Screw type)

Introduction

3

1.2.3 System Specification

 10.4” TFT LCD
 Heat Dispensing Design
 Disk drive housing:

 One 2.5” SATA drive

 Net Weight

 1.8 Kgs (3.96 lb)

 Dimension (Main Body Size)

 292.5x 45.8 x 235.8mm

 Operation Temperature

 0℃ to 50℃(with W.T. DRAM/HDD in airflow condition)

 Relative Humidity

 10% to 95% @ 40℃, Non-Condensing

 Vibration

 5 to 500 Hz, 2.0 G random for SSD
 5 to 500 Hz, 2.0 G random for CF card

 Power input

 10~30VDC with phoenix power connector
 External 60W AC Adapter

GOT-5100T User’s Manual

— Power Input: 100VAC to 240VAC
— Power Output: 12VDC, Max. 5A

NOTE:All specifications and images are subject to change without notice.
NOTE:If the operation temperature is higher than 35℃, the wide temperature DRAM and HDD

are recommended to be used o the device.

Introduction

GOT5100T-832 User’s Manual

4

1.3 Dimensions

This diagram shows you dimensions and outlines of the GOT5100T-832.

Introduction

GOT-5100T User’s Manual

5

Introduction

GOT5100T-832 User’s Manual

6

1.4 I/O Outlets

Please refer to the following illustration for I/O locations of the GOT5100T-832.

Introduction

GOT-5100T User’s Manual

7

1.5 Packing List

When you receive the GOT5100T-832, the bundled package should contain the following items:

 GOT5100T-832 x 1
 Panel Mount Kit x 6
 Driver CD x1
 Wall-Mount Kit x1
 HDD Mylar x 1
 Power Adapter & power cord (for GOT5100T-832-J)

If you can not find the package or any items are missing, please contact AXIOMTEK distributors
immediately.

Introduction

GOT5100T-832 User’s Manual

8

MEMO:

Introduction

GOT5100T-832 User’s Manual

9

CHAPTER 2

HARDWARE INSTALLATION

The GOT5100T-832 provides rich I/O ports and flexible expansions for you to meet different
demand. The chapter will show you how to install the hardware. It includes:

 CompactFlash™ Card
 Serial Port
 Ethernet
 Mounting Way
 Hard disk
 Dram
 Wireless LAN Card

2.1 CF card Installation

The GOT5100T-832 provides one CF slot for users to install CompactFlash™ card. Please refer
to the following instructions for installation:

Step 1 Turn off the system, and unplug the power cord.
Step 2 Find out the cover on the side of the system.

Step 3 Locate the CompactFlashTM socket, and insert the card into the socket.

Hardware Installation

GOT5100T-832 User’s Manual

10

Pin

Signal

Pin

Signal

1

Data Carrier Detect (DCD)

6

Data Set Ready (DSR)

2

Receive Data (RXD)

7

Request To Send (RTS)

3

Transmit Data (TXD)

8

Clear To Send (CTS)

4

Data Terminal Ready (DTR)

9

Ring Indicator (RI)

5

Ground (GND)

Description

Function

Jumper Setting

COM 1

RS-232 (Default)

JP9

JP7

JP8

RS-422

JP9

JP7

JP8

RS-485

JP9

JP7

JP8

2.2 Serial Ports Interface

The GOT5100T-832 has two onboard serial ports, COM1 (RS-232/ 422/ 485) and COM2 (RS-

232).
The following table shows you the pin assignments of this connector:
The following table shows you the pin assignments of this connector:

In addition, COM1 can be set for RS-232/422/485 by jumper. The jump setting is listed as below:

Hardware Installation

GOT5100T-832 User’s Manual

11

1 5

6 10

Pin

RS-232

RS-422

RS-485

1

DCD

TX-

Data-

2

RXD

TX+

Data+

3

TXD

RX+

N.C 4 DTR

RX-

N.C.

5

GND

No use

No use

6

DSR

No use

No use

7

RTS

No use

No use

8

CTS

No use

No use

9

RI

No use

No use

2.2.1 COM1&COM2 Connector

The COM1 and COM2 is a standard DB-9 connector. This connector is equipped with +5V level
power capability on DCD and +12V level on RI by setting JP10 and JP11. The pin assignment of
RS-232/RS-422/RS-485 is listed on the following table. If you need COM1 port to support RS-422
or RS-485 mode, please refer to Jumper Settings

COM1(SBC87832)

Hardware Installation