AXIOMTEK GOT3217W-845-PCT User Manual

GOT3217W-845-PCT

All-in-One

21.5” FHD Fanless
10-Point Multi-Touch PANEL PC

User’s Manual

ii

Disclaimers

This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third
party’s rights, or any liability arising from such uses.

Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make any
commitment to update any information in this manual.

Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.

No part of this document may be reproduced, stored in a retrieval system, or transmitted in any
forms or by any means, electronic, mechanical, photocopying, recording, among others,
without prior written permission from Axiomtek Co., Ltd.

CAUTION

Wrong type of batteries may cause explosion. It is recommended that users only replace with
the same or equivalent type of batteries as suggested by the manufacturer once properly
disposing of any used ones.

Copyright 2017 Axiomtek Co., Ltd.
All Rights Reserved
Feb 2017, Version A1
Printed in Taiwan

iii

Safety Precautions

Before getting started, please read the following important safety precautions.

1. Be sure to ground yourself to prevent static charge when installing any internal
components. Use a grounding wrist strap and place all electronic components in any
static-shielded devices. Most electronic components are sensitive to static electrical
charge.

2. Disconnect the power cord from the GOT3217W-845-PCT series prior to any installation.
Be sure both the system and all external devices are turned off. Sudden surge of power
could ruin sensitive components. Make sure the GOT3217W-845-PCT Series is properly
grounded.

3. Do not open the system’s back cover. If opening the cover for maintenance is a must,
only a trained technician is allowed to do so. Integrated circuits on computer boards are
sensitive to static electricity. To avoid damaging chips from electrostatic discharge,
observe the following precautions:

 Before handling a board or integrated circuit, touch an unpainted portion of the

system unit chassis for a few seconds. This will help to discharge any static
electricity on human body.

 When handling boards and components, wear a grounding wrist strap available

from most electronic component stores.

Trademark Acknowledgments

Axiomtek is a trademark of Axiomtek Co., Ltd.
Intel® and Pentium® are registered trademarks of Intel Corporation.
Windows 10, Windows 10 IoT Enterprise, Windows 8.1, Windows 8, Windows 7, are
trademarks of Microsoft Corporation.
Other brand names and trademarks are the properties and registered brands of their
respective owners.

iv

Table of Contents

Disclaimers ..................................................................................................... ii

Safety Precautions ........................................................................................ iii

Section 1 Introduction ............................................. 1

1.1 General Descriptions .......................................................................... 1

1.2 Specifications ...................................................................................... 2

1.3 Dimensions and Outlines ................................................................... 4

1.4 I/O Outlets ............................................................................................ 6

1.5 Packing List ......................................................................................... 7

Section 2 Hardware and Installation ...................... 9

2.1 Board Layout ....................................................................................... 9

2.2 Jumper and Connector Settings ...................................................... 10

2.2.1 ‘Auto Power On’ Jumper (JP7) .................................................................. 10

2.2.2 ‘Restore BIOS Optimal Defaults’ Jumper (JP8) ........................................ 10

2.2.3 COM Port Connector .................................................................................. 11

2.2.4 Ethernet Connector .................................................................................... 11

2.3 Mounting Methods ............................................................................ 12

2.4 Hardware Installation ........................................................................ 14

2.4.1 Installing a HDD ........................................................................................ 14

2.4.2 Installing a DRAM ...................................................................................... 16

2.4.3 Installing a Wireless LAN Card ................................................................. 17

2.4.4 Connecting the Power Input ...................................................................... 19

Section 3 AMI BIOS Setup Utility .......................... 21

3.1 Navigation Keys ................................................................................ 21

3.2 Main Menu .......................................................................................... 22

3.3 Advanced Menu ................................................................................. 23

3.3.1 NCT6106D Super IO Configuration ................................................................... 23

3.3.2 Hardware Monitor .............................................................................................. 25

3.3.3 ACPI Settings .................................................................................................... 26

3.3.4 CPU Configuration ............................................................................................. 27

3.3.5 SATA Configuration ............................................................................................ 28

3.3.6 USB Configuration ............................................................................................. 29

3.3.7 Utility Configuration ........................................................................................... 29

3.3.8 PCIE/mSATA Mini Card Configuration ............................................................... 30

3.4 Chipset Menu ..................................................................................... 31

v

3.4.1 North Bridge....................................................................................................... 31

3.4.2 South Bridge ...................................................................................................... 32

3.5 Security Menu .................................................................................... 33

3.6 Boot Menu .......................................................................................... 34

3.7 Save & Exit Menu .............................................................................. 35

Section 4 Driver and Installation ......................... 37

4.1 Operating System ............................................................................. 37

4.1.1 Installing System Drivers ........................................................................... 37

4.2 Touch Screen ..................................................................................... 38

vi

This page is intentionally left blank.

GOT3217W-845-PCT User ’s Manual

Introduction 1

Section 1

Introduction

This Section contains general information and detailed specifications of the
GOT3217W-845-PCT, including the following subsections:

Figure 1-1 Front panel of the GOT3217W-845-PCT

 General Descriptions
 Specifications
 Dimensions and Outlines
 I/O Outlets
 Packing List

1.1 General Descriptions

The GOT3217W-845-PCT adopts a 21.5-inch FHD LCD with 250-nit brightness and an Intel®
Pentium® Processor N3710 (2M Cache, up to 2.56 GHz), providing excellent computing
performance and thermal resistance. This fanless platform is especially designed for operation
under a harsh environment including steel refinery, oil pipe, ship, machine maker, and many
more. Having abilities below surely makes GOT3217W-845-PCT a most robust and
cost-effective solution.

 Design for extended operating temperature range and ingress protection

The GOT3217W-845-PCT is featured by a technology to sustain extended operating
temperature range between 0°C and +45°C by incorporating compact ID and fanless cooling
system with a low power Intel® Pentium® Processor N3710 (2M Cache, up to 2.56 GHz). It
also adopts an IP65 front bezel to protect itself from liquid and dust. These designs help make
the system a power-efficient solution.

 Reliable and stable design

The GOT3217W-845-PCT is specially designed for vibration-prone environments, best for
the transportation (vehicle, railway, marine) and industrial machinery markets. To suit the need
of high capacity storage, the GOT3217W-845-PCT can work in operation mode under 1.0G (i.e.
gravitational acceleration) (10 ~ 500Hz, random for HDD™) with a patent of anti-vibration
design. The design behind the patent has improved the system reliability and sustainability.
(Note: Sometimes heavy-vibration may cause the LCD screen to flash in white color; however,
it won’t affect the function of the product.)

GOT3217W-845-PCT User’s Manual

2 Introduction

 WLAN antenna supported (optional)

The GOT3217W-845-PCT comes with 2 PCI Express Mini Card slots as an add-on option to
connect s a wireless LAN card under 802.11 a/b/g/n protocols, or with other 3G/GPRS
applications, etc. These slots also come with 3 optional fixed rotational WLAN/3G antennas for
wireless network connection.

 Multi- PCAP touch surface of 7H hardness

The GOT3217W-845-PCT is designed with a user friendly multi- PCAP touch. Users can
operation it with direct touch. The surface hardness is up to 7H, good for applications of
anti-scratch purpose.

 Other features

The GOT3217W-845-PCT utilizes one 204-pin DDR3L SODIMM system memory up to 8GB at
the maximum, one SATA HDD and one mSATA. It provides an over-current protection-fuse and
a full set of I/O including RS-232/422/485, USB 2.0, USB 3.0, audio (line-out), and Gigabit
Ethernet. Additionally, this slim unit supports panel mount as the standard installation, as well
as optionally wall mount, VESA mount and desktop stand mount.

1.2 Specifications

Main CPU Board

 CPU

 Intel® Pentium® Processor N3710 (2M Cache, up to 2.56 GHz) onboard

 System Memory

 1 x 204-pin DDR3L SO-DIMM socket
 Maximum memory up to 8GB

 BIOS

 AMI UEFI BIOS

I/O System

 Standard I/O

 2 x RS-232/422/485
 2 x USB 2.0
 2 x USB 3.0

 Ethernet

 2 x RJ45 for Gigabit Ethernet (Intel i211AT)

 Audio

 1x Line-out

 Expansion

 1 x Mini-card slot (w/SIM slot)
 1 x Mini-card slot (supports mSATA, optional)

 Storage

 1 x 2.5” SATA
 1 x mSATA

GOT3217W-845-PCT User ’s Manual

Introduction 3

 Power connector

 Phoenix power connector or screw power connector

System Specifications

 21.5” FHD (1920x1080) LCD with LED backlight
 10-point Multi- PCAP touch
 A design of fanless heat dispensation
 IP65 aluminum front bezel
 Disk drive housing:

 One 2.5” SATA drive

 Net weight

 7.6 Kgs

 Dimensions (of the main body)

 547.6 x 339 x 58.5 mm

 Operating temperatures

 0°C to 45°C

 Relative humidity

 20% to 90% @ 40°C, Non-condensing

 System power input

 DC power input : 24VDC with Phoenix power connector
 AC power input : 12VDC/5A, 60W power adapter

NOTE: All specifications and images are subject to change without notice.

The performance of the system might be adversely affected at an operating
temperature above 40°C.

GOT3217W-845-PCT User’s Manual

4 Introduction

1.3 Dimensions and Outlines

Diagram 1-1 shows the dimensions and outlines of the front panel of the GOT3217W-845-PCT

Diagram 1-1 Front dimensions and outline of the GOT3217W-845-PCT

Front dimensions: 547.6 x 339.1 x 57.6 mm

GOT3217W-845-PCT User ’s Manual

Introduction 5

Diagram 1-2 Back outline of the GOT3217W-845-PCT

Diagram 1-3 Cutting-out dimensions of the GOT3217W-845-PCT

Cut out dimensions: 534.69 x 326.15 mm

GOT3217W-845-PCT User’s Manual

6 Introduction

1.4 I/O Outlets

Please refer to Figures 1-2 and 1-3 for I/O locations of the GOT3217W-845-PCT.

Figure 1-2 Bottom view of the GOT3217W-845-PCT

Figure 1-3 Side view of the GOT3217W-845-PCT

GOT3217W-845-PCT User ’s Manual

Introduction 7

1.5 Packing List

A complete bundled package should contain the following items:

 GOT3217W-845-PCT unit x 1
 Driver disc x1 (various OS versions and bundles available)
 Phoenix connector x 1 (DC power version only)
 Panel mount kit x 16
 Screws for HDD x 2
 SATA data cable x 1
 SATA power cable x 1

Please contact an Axiomtek distributor immediately if any of the above-mentioned items is
missing.

GOT3217W-845-PCT User’s Manual

8 Introduction

This page is intentionally left blank.

GOT3217W-845-PCT User ’s Manual

Hardware and Installation 9

Section 2

Hardware and Installation

The GOT3217W-845-PCT provides rich I/O ports and flexible expansion for users to meet
different demands; for example, in a case of CF card expansion. This Section describes
hardware installation, including the following subsections:

 Board Layout
 Jumper and Connector Setting
 Mounting Methods
 Hardware Installation
 Power Input

2.1 Board Layout

Please follow the steps below to open the GOT3217W-845-PCT unit.

Step 1 Unscrew 8 screws (see red circles in Figure 2-1) on the back cover.

Figure 2-1 Back cover

Step 2 Remove the back cover.

Figure 2-2 Board layout

GOT3217W-845-PCT User’s Manual

10 Hardware and Installation

2.2 Jumper and Connector Settings

Jumper is a small component consisting of jumper clip and jumper pins. Install jumper clip on 2
jumper pins to close the pins. And remove jumper clip from 2 jumper pins to open the pins.
Diagram 2-1 illustrates how to set up a jumper.

Diagram 2-1 Definitions of pin settings

Pins 1-2 open Pins 1-2 close Pins 1-2 close All pins open
Before applying power to GOT3217W-845-PCT, please make sure all of the jumpers and

connectors are in default position as listed in Table 2-1.

Table 2-1 Factory mode of jumper settings

Jumper

Descriptions

Setting

JP7

Auto Power On
Default: Disable

2-3 close

JP8

Restore BIOS Optimal Defaults (Clear CMOS)
Default: Normal Operation

1-2 close

2.2.1 ‘Auto Power On’ Jumper (JP7)

If JP7 is enabled for power input, the system will be automatically power on without pressing
soft power button. If JP7 is disabled for power input, it is necessary to manually press soft
power button to power on the system (see Table 2-2).

Table 2-2 JP7 setting

2.2.2 ‘Restore BIOS Optimal Defaults’ Jumper (JP8)

Put jumper clip to pin 2-3 for a few seconds then move it back to pin 1-2. Doing this procedure
can restore BIOS optimal defaults (see Table 2-3).

Table 2-3 JP8 setting

Function

Setting

Enable auto power on

1-2 close

Disable auto power on (Default)

2-3 close

Function

Setting

Normal operation (Default)

1-2 close

Restore BIOS optimal defaults

2-3 close

GOT3217W-845-PCT User ’s Manual

Hardware and Installation 11

2.2.3 COM Port Connector

The pin assignment for RS-232/ 422/ 485 is listed In Table 2-4.

Table 2-4 Pin assignment for RS-232/ 422/ 485

2.2.4 Ethernet Connector

There are two RJ-45 connectors, LAN1 and LAN2, inside the GOT3217W-845-PCT. Ethernet
connection can be established by plugging one end of the Ethernet cable into this RJ-45
connector and the other end (phone jack) to a 1000/100/10-Base-T hub.

Please refer to Table 2-5 for detailed pin assignment for LAN1 and LAN2.

Table 2-5 Pin assignment for LAN1/ LAN2

Pin

Signal

Pin

Signal

L1

MDI0+

L5

MDI2+

L2

MDI0-

L6

MDI2-

L3

MDI1+

L7

MDI3+

L4

MDI1-

L8

MDI3-

A

Active LED (Yellow)

B

100 LAN LED (Green) / 1000 LAN LED
(Orange)

Pin

RS-232

RS-422

RS-485

1

DCD

TX-

Data-

2

RXD

TX+

Data+

3

TXD

RX+

No use

4

DTR

RX-

No use

5

GND

GND

GND

6

DSR

No use

No use

7

RTS

No use

No use

8

CTS

No use

No use

9

RI

No use

No use

GOT3217W-845-PCT User’s Manual

12 Hardware and Installation

2.3 Mounting Methods

There are four ways to install the GOT3217W-845-PCT, namely: panel/ VESA/ wall/ desktop
mount.

The GOT3217W-845-PCT provides a standard panel mount kit. It can be installed by way of
panel mount (see Figure 2-1, 2-2).

Figure 2-1 Panel mount (back chassis)

Figure 2-2 Panel mount kit

GOT3217W-845-PCT User ’s Manual

Hardware and Installation 13

Alternatively, the GOT3217W-845-PCT can be installed by way of VESA mount which is in the
dimensions of 100x100 mm. Simply fix four screws to fasten the kit from the back chassis, as
shown in Diagram 2-3. Additionally, users can otherwise go for wall mount as an option, as
shown in Diagram2-4.

Diagram 2-3 VESA mount (back chassis)

Diagram 2-4 Wall mount (back chassis)

GOT3217W-845-PCT User’s Manual

14 Hardware and Installation

2.4 Hardware Installation

2.4.1 Installing a HDD

The GOT3217W-845-PCT provides a convenient Hard Disk Drive (HDD) bracket for users to
install a 2.5” SATA HDD. Please follow the steps:

Step 1 Refer to Section 2.1 to open the back cover and dissemble the HDD tray by

un-screwing the 2 screws (as shown in the red circles in Figure 2-5).

Figure 2-5 Separating the bracket from the HDD tray

Step 2 Fasten a HDD from the back side of the bracket with two screws (see Figure

2-6).

Figure 2-6 Fastening a HDD to the bracket

Front: Back:

GOT3217W-845-PCT User ’s Manual

Hardware and Installation 15

Step 3 Lodge the two points on to the holes on the HDD tray (see red circles in

Figure 2-7) and fix the bracket onto the HDD tray with two screws. Also,
please make sure the two holes at the back of the HDD are embedded into the
lower two highlight points on the HDD tray (see blue circles in Figure 2-7) to
secure the entire bracket and the HDD

Figure 2-7 Putting the bracket back to the HDD tray

Step 4 Plug two cables – one for SATA and the other for Power - to two connectors

(see Figure 2-8) to complete the installation.

Figure 2-8 Connecting cables to connectors

GOT3217W-845-PCT User’s Manual

16 Hardware and Installation

2.4.2 Installing a DRAM

The GOT3217W-845-PCT provides one 204-pin DDR3L SODIMM socket that supports system
memory up to 8GB. Please follow steps below to install a memory module:

Step 1 Refer to Section 2.1 to open the back cover.

Step 2 Locate the DIMM socket (as shown in Figure 2-9) on mainboard (Part No.

SBC87845).

Figure 2-9 DIMM spot

Step 3 Insert a DRAM into the DIMM socket, and then push it down firmly until it is

clipped with the socket (as shown in Figure 2-10). Now the installation is
completed.

Figure 2-10 Inserting a DRAM into the DIMM

GOT3217W-845-PCT User ’s Manual

Hardware and Installation 17

2.4.3 Installing a Wireless LAN Card

The GOT3217W-845-PCT comes with two Mini card slots for users to install wireless LAN
cards. Users can choose either Slot 1 or Slot 2 to install the wireless LAN card. Please refer to
the following instructions and illustration for the installation of the wireless LAN card.

Step 1 Refer to Section 2.1 to open the back cover; then locate the Mini card slot (as

shown in Figure 2-11) on the mainboard.

Figure 2-11 Slots 1 and 2 spots

Step 2 Insert the wireless LAN card to one of the two slots. Push it down firmly。

Then screw tightly the card to the mainboard (see Figure 2-12).

Figure 2-12 Inserting and securing a wireless LAN card

GOT3217W-845-PCT User’s Manual

18 Hardware and Installation

Step 3 Locate the antenna cable and connect it to the wireless LAN card (see Figure

2-13).

Figure 2-13 Connecting the antenna to the wireless LAN card

Step 4 Remove the antenna plug from the top of back cover, and then install the

antenna on the antenna connector (see Figures 2-14 and 2-15).

Figure 2-14 Antenna outlet (internal view)

Figure 2-15 Antenna outlet (external view)

NOTE: Please use an extended bracket when using a half-size Mini card.

GOT3217W-845-PCT User ’s Manual

Hardware and Installation 19

2.4.4 Connecting the Power Input

The GOT3217W-845-PCT is equipped with a Phoenix type of power connector which adopts
24VDC. Please follow the signs on the power connector to connect DC power source (see
Figure 2-16).

Figure 2-16 Power connector

+: Power positive －:Power negative

NOTE: The safety ground must be connected to ensure that the unit works appropriately.

GOT3217W-845-PCT User’s Manual

20 Hardware and Installation

This page is intentionally left blank.

GOT3217W-845-PCT User ’s Manual

AMI BIOS Setup Utility 21

Section 3

AMI BIOS Setup Utility

This Section provides users with detailed descriptions about how to set up basic system
configurations through the AMI BIOS setup utility.

3.1 Navigation Keys

The BIOS setup/utility uses a key-based navigation system called hot keys. Most of the hot
keys for the BIOS setup utility can be used at any time during the setup navigation process.
These hot keys include <F1>, <F2>, <F3>, <F4>, <Enter>, <ESC>, arrow keys, and so on (as
listed in Table 3-1).

NOTE: Some of navigation keys may differ from one screen to another.

Table 3-1 Descriptions of hot keys

Hot Keys

Descriptions

<> and <>
Left/Right

The <> and <> keys are used to select a setup screen.

<> and <>
Up/Down

The <> and <> keys are used to select a setup screen or
sub-screen.

<+> and <>
Plus/Minus

The <+> and <> keys you are used to change the field value of a
particular setup item.

<Tab>

The <Tab> key is used to select setup fields.

<F1>

The <F1> key is used to display the general help screen.

<F2>

The <F2> key is used to load previous values.

<F3>

The <F3> key is used to load optimized defaults.

<F4>

The <F4> key is used to save any changes made then exit the setup.
Press the <F4> key to save any changes.

<Esc>

The <Esc> key is used to discard any changes made then exit the
setup. Press the <Esc> key to exit the setup without saving your
changes.

<Enter>

The <Enter> key is used to display or change the setup option listed
for a particular setup item. The <Enter> key is also used to display
the setup sub- screens.

GOT3217W-845-PCT User’s Manual

22 AMI BIOS Setup Utility

3.2 Main Menu

Figure 3-1 Main menu

System Date / Time

Use this option to change the system time and date. Highlight System Time or System Date
using the up/ down/ left and right arrow keys (see Figure 3-1). Enter new values through the
keyboard. Press the <Tab> key or the arrow keys to move between fields. The date entered
must be in the MM/DD/YY format. The time is entered in HH:MM:SS format.

GOT3217W-845-PCT User ’s Manual

AMI BIOS Setup Utility 23

3.3 Advanced Menu

Figure 3-2 Advanced Menu

The Advanced menu allows users to set configurations of the CPU and other system devices.
Select any item on the left to go to the sub-menus (as shown in Figure 3-2).

► NCT6106D Super IO Configuration
► Hardware Monitor
► ACPI Settings
► CPU Configuration
► SATA Configuration
► USB Configuration
► Utility Configuration
► PCIE/mSATA Mini Card Configuration

Simply highlight the item of choice, then press <Enter> to go to sub-menus for more specific
options.

3.3.1 NCT6106D Super IO Configuration

The ‘NCT6106D Super IO Configuration’ page is to change the value of the Super IO
Configuration. The description of the selected item will appear on the right side of the screen
(as shown in Figure 3-3). For items marked with “”, please press <Enter> for further options
(as shown in Figure 3-4).

GOT3217W-845-PCT User’s Manual

24 AMI BIOS Setup Utility

Figure 3-3 Entering ‘NCT6106D Super IO Configuration’

► Serial Port 1 (COM1) / Serial Port 2 (COM2)

Serial port

This option is used to enable or disable serial port COM1/COM2.

Device Setting

This item specifies the base I/O port address and the Interrupt Request (IRQ) address of the
serial ports.
Optimal setting for Port 1 is 3F8/IRQ4.
Optimal setting for Port 2 is 2E8/IRQ3.

COM Port Type

This option is used to select COM Port Type: RS-232/422/ or 485.

Figure 3-4 ‘NCT6106D Super IO Configuration’ -> ‘Serial Port 1 (COM1)’

GOT3217W-845-PCT User ’s Manual

AMI BIOS Setup Utility 25

3.3.2 Hardware Monitor

Figure 3-5 shows a screen reflecting the health status of the hardware in real time.

Figure 3-5 Entering ‘Hardware Monitor’

GOT3217W-845-PCT User’s Manual

26 AMI BIOS Setup Utility

3.3.3 ACPI Settings

This screen is used to select options of the ACPI Configuration, and change the value of the
selected option. A description of the selected item appears on the right side of the screen.

ACPI Sleep State

This item allows users to select the Advanced Configuration and Power Interface (ACPI) state
to be used for system suspension. There are two choices under this selection: Suspend
Disable and S3 (Suspend to RAM) (as shown in Figure 3-6).

Figure 3-6 Entering ‘ACPI

Settings’

GOT3217W-845-PCT User ’s Manual

AMI BIOS Setup Utility 27

3.3.4 CPU Configuration

Figure 3-7 shows a page of CPU configuration with item Intel Virtualization Technology
[enable/disable] highlighted.

Figure 3-7 Entering ‘CPU Configuration’

GOT3217W-845-PCT User’s Manual

28 AMI BIOS Setup Utility

3.3.5 SATA Configuration

This screen allows users to select options for SATA Configuration, and change the value of the
selected option (see Figure 3-8).

SATA Controller

Highlight this item to set up SATA Controller to be Enable or Disable.

Figure 3-8 Entering ‘SATA Configuration’

GOT3217W-845-PCT User ’s Manual

AMI BIOS Setup Utility 29

3.3.6 USB Configuration

Please see Figure 3-9 to see what items can be set up under the page of USB Configuration.

Figure 3-9 Entering ‘USB Configuration’

3.3.7 Utility Configuration

Figure 3-10 shows the page once entering Utility Configuration.

Figure 3-10 Entering ‘Utility Configuration’

GOT3217W-845-PCT User’s Manual

30 AMI BIOS Setup Utility

3.3.8 PCIE/mSATA Mini Card Configuration

Highlighting item PCIE/mSATA Mini Card Configuration under the Advanced Menu, hit <Enter>
to enter a sub-screen as shown in Figure 3-11. There are two choices for Mino Card Mode:
PCIE and mSATA.

Figure 3-11 Entering ‘PCIE/mSATA Mini Card Configuration’

GOT3217W-845-PCT User ’s Manual

AMI BIOS Setup Utility 31

3.4 Chipset Menu

The Chipset menu gives memory information about the North Bridge and TXE information
about the South Bridge (see Figure 3-12).

Figure 3-12 Chipset Menu

3.4.1 North Bridge

Memory information about the North Bridge is show in Figure 3-13.

Figure 3-13 Entering ‘North Bridge’

GOT3217W-845-PCT User’s Manual

32 AMI BIOS Setup Utility

3.4.2 South Bridge

TXE information about the South Bridge is show in Figure 3-14.

Figure 3-14 Entering ‘South Bridge’

GOT3217W-845-PCT User ’s Manual

AMI BIOS Setup Utility 33

3.5 Security Menu

Figure 3-15 Security Menu

GOT3217W-845-PCT User’s Manual

34 AMI BIOS Setup Utility

3.6 Boot Menu

The Boot menu allows users to change boot options of the system. Users can highlight any of
the items on the left frame of the screen to go to any particular sub menus (as shown in Figure
3-16).

Figure 3-16 Boot Menu

Setup Prompt Timeout

Enter a numeric value here as the length for timeout.

Bootup NumLock State

Use this item to select the power-on state for NumLock. The default setting is [On].

Quiet Boot

Use this item to enable or disable the Quite Boot state. The default setting is [Disabled].

PXE ROM

Use this item to enable or disable the Pre-boot Execution Environment (PXE). The default
setting is [Disabled].

Boot Option Priorities

Use this item to specify the overall boot order among the available devices.

GOT3217W-845-PCT User ’s Manual

AMI BIOS Setup Utility 35

3.7 Save & Exit Menu

Figure 3-17 Save & Exit Menu

GOT3217W-845-PCT User’s Manual

36 AMI BIOS Setup Utility

This page is intentionally left blank.

GOT3217W-845-PCT User ’s Manual

Driver and Installation 37

Section 4

Driver and Installation

4.1 Operating System

The GOT3217W-845-PCT is compatible with operating systems Windows 10 and Windows 10
IoT Enterprise. To facilitate the installation of system drivers, please carefully read the
instructions in this Section before any of such installation.

4.1.1 Installing System Drivers

Step 1 Insert the Driver disc included in the Packing List and select the “\Drivers”.
Locate the Win 10 directory first (if Win 10 is user’s choice).

Figure 4-1 Folders of system drivers

Step 2 Under directory Win 10, there are more file folders as shown below.

Step 3 Select all files and follow the installing procedure from Steps 1 to 6. Please
don’t run Step 7 that is the driver for resistive touch screen.

NOTE: During the installation of “Graphic” driver, if the GOT3217W-845-PCT is idle for too

long, then the “Power Management” program may turn off the GOT3217W-845-PCT
LCD monitor. If this happens, it will not be possible to wake up the LCD monitor of
the GOT3217W-845-PCT. Rather, users need to reboot the GOT3217W-845-PCT and
install the “Graphic” driver correctly.

NOTE: Windows 10 / Windows 10 IoT support touch mode with 10-point multi-touch

function.

GOT3217W-845-PCT User’s Manual

38 Driver and Installation

4.2 Touch Screen

The GOT3217W-845-PCT is designed based on the technology of projected capacitive
multi-touch screen of which specifications are listed below. The touch driver will be installed
automatically and can drive the touch panel to get two fingers touch function that based on the
Windows 10 and Windows 10 IoT Enterprise support.



Table 4-1 Touch screen specifications

Touch Screen

Projected capacitive 10 point multi-touch

Touch Screen Controller

Mastouch USB Touch Screen Controller IC

Communications

USB interface

Power Supply

5V

Power Consumption

40mA

Input Method

Finger or Cap.Stylus

Resolution

25ppi (Min.)
Note: Base on WIN7 definition, ppi (Pixcel per inch)

Win7 USB Driver

Non-Driver

Calibration

Non-Calibration