AXIOMTEK GOT3187W-832-PCT User Manual

Page 1
GOT3187W-832-PCT
All-in-One
18.5” WXGA TFT Fanless Compact-Size PANEL PC
User’s Manual
Page 2
Disclaimers
This manual has been carefully checked and believed to contain accurate information. Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third partys rights, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy, completeness or usefulness of any information in this document. Axiomtek does not make any commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Axiomtek Co., Ltd.
CAUTION
If you replace wrong batteries, it causes the danger of explosion. It is recommended by the manufacturer that you follow the manufacturers instructions to only replace the same or equivalent type of battery, and dispose of used ones.
Copyright 2013 Axiomtek Co., Ltd.
All Rights Reserved August 2013, Version A3 Printed in Taiwan
Page 3
Safety Precautions
Before getting started, read the following important cautions.
1. Be sure to ground yourself to prevent static charge when installing the internal components. Use a grounding wrist strap and place all electronic components in any static-shielded devices. Most electronic components are sensitive to static electrical charge.
2. Disconnect the power cords from the GOT3187W-832-PCT Series before making any installation. Be sure both the system and the external devices are turned OFF. Sudden surge of power could ruin sensitive components. Make sure the GOT3187W-832-PCT Series is properly grounded.
3. Do not open the system’s top cover. If opening the cover for maintenance is a must, only a trained technician is allowed to do so. Integrated circuits on computer boards are sensitive to static electricity. To avoid damaging chips from electrostatic discharge, observe the following precautions:
Before handling a board or integrated circuit, touch an unpainted portion of the
system unit chassis for a few seconds. This will help to discharge any static electricity on your body.
When handling boards and components, wear a wrist-grounding strap, available
from most electronic component stores.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd. Windows® is a trademark of Microsoft Corporation.
IBM, PC/AT, PS/2 are trademarks of International Business Machines Corporation. Intel® and Atom® are trademarks of Intel Corporation.
AMI is trademark of American Megatrend Inc. Other brand names and trademarks are the properties and registered brands of their
respective owners.
iii
Page 4
Table of Contents
CHAPTER 1 INTRODUCTION .............................................................................. 1
CHAPTER 2 HARDWARE AND INSTALLATION ...................................................... 7
2.1 OPEN BACK COVER ............................................................................................... 8
2.2 CF CARD INSTALLATION ......................................................................................... 9
2.3 JUMPER AND SWITCH SETTINGS ........................................................................... 11
2.4 COM PORT CONNECTOR ................................................................................... 13
2.5 ETHERNET ....................................................................................................... 14
2.6 MOUNTINGS: PANEL / WALL / VESA ................................................................... 14
2.7 HDD INSTALLATION ........................................................................................... 16
2.8 DRAM INSTALLATION ........................................................................................ 18
2.9 WIRELESS LAN CARD INSTALLATION ..................................................................... 20
2.10 POWER INPUT .................................................................................................. 22
CHAPTER 3 AMI BIOS SETUP UTILITY ................................................................ 24
3.1 STARTING......................................................................................................... 24
3.2 NAVIGATION KEYS ............................................................................................. 24
3.3 MAIN MENU .................................................................................................... 25
3.4 ADVANCED MENU ............................................................................................. 26
3.5 CHIPSET MENU ................................................................................................. 33
3.6 BOOT MENU .................................................................................................... 35
3.7 SECURITY MENU ............................................................................................... 36
3.8 SAVE & EXIT MENU ........................................................................................... 37
CHAPTER 4 DRIVERS INSTALLATION ................................................................ 40
4.1 SYSTEM ........................................................................................................... 40
4.2 TOUCH SCREEN ................................................................................................. 40
4.3 EMBEDDED O.S. ............................................................................................... 41
iv
Page 5
This page is intentionally left blank.
v
Page 6
Page 7
GOT3187W-832-PCT User’s Manual
Back
Chapter 1
Introduction
This chapter contains general information and detailed specifications of the GOT3187W-832-PCT. Chapter 1 includes the following sections:
General Description Specification Dimensions I/O Outlets Package List
1.1 General Description
The GOT3187W-832-PCT adopts a 18.5-inch WXGA TFT LCD with 300-nit brightness and an Intel® Atom processor D2550 1.86 GHz to provide excellent computing performance and thermal resistance. This fanless platform is especially designed for operating under heavy-duty environment including steel refinery, oil pipe, ship, machine maker operating systems and many more. Having below abilities makes GOT3187W-832-PCT surely a most robust and cost-effective solution.
Wide Operating Temperature Range
GOT3187W-832-PCT features a technology of wide operating temperature range which allows it to work between -10°C to +50°C. It incorporates no fixture frame touch screen and fanless cooling system with a low power Intel® Atom processor D2550 1.86 GHz, making the platform a power-efficient solution.
Introduction 1
Page 8
GOT3187W-832-PCT User’s Manual
Back
Reliable and Stable Design
The GOT3187W-832-PCT adopts a fan-less cooling system and a CompactFlash™ card, which makes it especially suitable for vibration-heavy environments, best for the transportation, ship, and industrial machinery markets. For high capacity storage requirement, GOT3187W-832-PCT can work under 2G (5 ~ 500Hz, random for CompactFlash™) in operation mode with a patent of anti-vibration design. The patent improves the system reliability and sustainability.
WLAN Antenna Supported (optional)
GOT3187W-832-PCT has a PCI Express Mini Card slot for optional add-ons such as wireless LAN card for 802.11 b/g connections & 3G/GPRS application, graphics-enhanced video card, universal analog TV/FM tuner/AV capture card, and more. It also provides an optional fixed rotational WLAN antenna for wireless network connection.
More Features
GOT3187W-832-PCT utilizes one 204-pin DDR3 SODIMM system memory max. up to 4GB, one SATA HDD and one CompactFlash slot. It provides over-current protection-fuse and a full set of I/O including 1 RS-232, 1 RS-232/422/485, 4 USB 2.0, 1 audio (line-out), 2 Gigabit Ethernet. Additionally, this slim unit supports panel mount, wall mount (optional), VESA mount (optional) and desktop stand (optional).
1.2 Specifications
Main CPU Board
CPU
Intel
System Chipset
Intel
System Memory
One 204-pin DDR3 SO-DIMM socket Maximum memory up to 4GB
BIOS
America Megatrends BIOS
I/O System
Standard I/O
One RS-232 and one RS-232/422/485 Four USB 2.0
®
AtomTM D2550 1.86GHz processor onboard
®
NM10 Express
2 Introduction
Page 9
Back
Ethernet
Two Gigabit Ethernet
Audio
One Line-out
Expansion
One Mini card
Storage
One slot for CF card One SATA
Power connector
Phoenix power connector
System Specification
18.5 WXGA(1366x768) LCD with LED backlight Projected Capacitive Touch
GOT3187W-832-PCT User’s Manual
Fanless Heat Dispensing Design IP65 aluminum front bezel Disk drive housing:
One 2.5 SATA drive
Net Weight
5.8 Kgs (12.79 lb)
Dimension (Main Body Size)
460.8mm x 58.5mm x 285mm
Operation Temperature
-10 to 50
Relative Humidity
20% to 95% @ 40, Non-Condensing
Power input
DC power 10~30V (phoenix type)
Note: All specifications and images are subject to change without notice.
Note: If the operation temperature is higher than 40℃, the wide temperature
HDD/CF are recommended to be used on the device.
Note: If the operation temperature is higher than 45℃, the wide temperature
memory module is recommended to be used on the device.
Introduction 3
Page 10
GOT3187W-832-PCT User’s Manual
Back
1.3 Dimensions and Outlines
The following diagrams show the dimensions and outlines of GOT3187W-832-PCT.
4 Introduction
Page 11
GOT3187W-832-PCT User’s Manual
Back
No
Function
No
Function
1
POWER SWITCH (ATX)
5
COM 2 (RS-232)
2
Power Input connector (Screw)
6
Ethernet (RJ-45)
3
Dual USB 2.0 ports
7
Dual USB 2.0 ports
4
COM 1 (RS-232/422/485)
8
AUDIO (LINE-OUT)
1.4 I/O Outlets
Please refer to the following illustration for I/O locations of the GOT3187W-832-PCT.
Introduction 5
Page 12
GOT3187W-832-PCT User’s Manual
Back
1.5 Packing List
When you receive the GOT3187W-832-PCT, the bundled package should contain the following items:
GOT3187W-832-PCT unit x 1 Driver CD x 1 Phoenix connector x 1 Panel mount kit x 12 Screws for HDD x 4
If you cannot find the package or any items are missing, please contact Axiomtek distributors immediately.
6 Introduction
Page 13
GOT3187W-832-PCT User’s Manual
Back
Chapter 2
Hardware and Installation
The GOT3187W-832-PCT provides rich I/O ports and flexible expansions for you to meet different demand, for example CF card. The chapter will show you how to install the hardware. It includes:
Open back cover CompactFlash Card Serial Port Ethernet Mounting Method Hard disk DRAM Wireless LAN Card Power
Hardware and Installation 7
Page 14
GOT3187W-832-PCT User’s Manual
Back
2.1 Open back cover
This section tells users how to open back cover. Please follow the steps below.
Step 1 Unscrew 8 screws on the back cover. Please refer the photo below.
Step 2 Remove the back cover.
8 Hardware and Installation
Page 15
GOT3187W-832-PCT User’s Manual
Back
2.2 CF card Installation
The GOT3187W-832-PCT provides one CF slot for users to install CompactFlash card. Please refer to the following instructions for installation:
Step 1 Open the cover, unscrew 2 screws on the chassis.
Step 2 Stick mylar on the CF card.
Hardware and Installation 9
Page 16
GOT3187W-832-PCT User’s Manual
Back
Step 3 Insert the CF card to the CF card slot, then finding the CF cover from the system package and screw it.
10 Hardware and Installation
Page 17
GOT3187W-832-PCT User’s Manual
Back
Jumper
Description
Setting
JP4
Auto Power On Default: Disable
2-3 close
JP5
CF Voltage Selection Default: +3.3V
1-2 close
JP6
Restore BIOS Optimal Defaults (Clear CMOS) Default: Normal Operation
1-2 close JP7
COM1 RS-232/422/485 Mode Setting Default: RS-232
3-5, 4-6 close
JP8
3-5, 4-6 close
JP9
1-2 close
JP10
COM1 Data/Power Selection Default: RS-232 Data
Pin 1: DCD
3-5 close
Pin 9: RI
4-6 close
JP11
COM2 Data/Power Selection Default: RS-232 Data
Pin 1: DCD
3-5 close
Pin 9: RI
4-6 close
2.3 Jumper and Switch Settings
Jumper is a small component consisting of jumper clip and jumper pins. Install jumper clip on 2 jumper pins to close. And remove jumper clip from 2 jumper pins to open. The following illustration shows how to set up jumper.
Before applying power to GOT3187W-832-PCT, please make sure all of the jumpers and switch are in factory default position. Below you can find a summary table and onboard default settings.
Hardware and Installation 11
Page 18
GOT3187W-832-PCT User’s Manual
Back
Description
Jumper Setting
RS-232 (Default)
JP7 JP8
JP9
RS-422
JP8
JP7
JP9
RS-485
JP8
JP7
JP9
Description
JP10~JP13
Pin1: DCD Pin9: RI (Default)
Pin1: +5V Pin9: +12V
Pin1: +5V Pin9: RI
Pin1: DCD Pin9: +12V
2.3.1 COM1 Configuration
The COM1 & COM2 are standard DB-9 connectors. Those connectors are equipped with The GOT3187W-832-PCT has two serial ports. COM1 is RS-232/422/485, while COM2 is RS-232. The following table shows you set COM1 port mode:
2.3.2 COM port Power Configuration
All of the serial ports can output data or power through jumper setting. The following table shows you how to do that.
Note: Each port +5V Maximum: 2A, +12V Maximum: 1A.
12 Hardware and Installation
Page 19
GOT3187W-832-PCT User’s Manual
Back
Function
Setting
Enable auto power on
1-2 close
Disable auto power on (Default)
2-3 close
Function
Setting
Normal operation (Default)
1-2 close
Restore BIOS optimal defaults
2-3 close
Pin
RS-232
RS-422
RS-485
1
DCD
TX-
Data-
2
RXD
TX+
Data+
3
TXD
RX+
No use
4
DTR
RX-
No use
5
GND
GND
GND
6
DSR
No use
No use
7
RTS
No use
No use
8
CTS
No use
No use
9
RI
No use
No use
2.3.3 Auto Power On (JP4)
If JP4 is enabled for power input, the system will be automatically power on without pressing soft power button. If JP4 is disabled for power input, it is necessary to manually press soft power button to power on the system.
2.3.4 Restore BIOS Optimal Defaults (JP6)
Put jumper clip to pin 2-3 for a few seconds then move it back to pin 1-2. Doing this procedure can restore BIOS optimal defaults.
2.4 COM port Connector
The pin assignment of RS-232/RS-422/RS-485 is listed on the following table. If you need COM1 port to support RS-422 or RS-485 mode, please refer to Jumper Settings
Hardware and Installation 13
Page 20
GOT3187W-832-PCT User’s Manual
Back
Pin
100Base-T
1000Base-T
1
TX+
BI-DA+
2
TX-
BI-DA-
3
RX+
BI-DB+
4
NC
BI-DB-
5
NC
BI-DC+
6
RX-
BI-DC-
7
NC
BI-DD+
8
NC
BI-DD-
1234567
8
RJ-45
2.5 Ethernet
The GOT3187W-832-PCT is equipped with a high performance Plug and Play Ethernet interface, full compliant with IEEE 802.3 standard, and can be connected with a RJ-45 LAN connector.
Please refer to detailed pin assignment list below:
2.6 Mountings: Panel / Wall / VESA
There are 4 application options for the GOT3187W-832-PCT, Panel/Wall/Desktop/VESA mountings.
2.6.1 VESA-ARM/Wall-Mount
The GOT3187W-832-PCT provides VESA mount: 100x100 mm. Screw four screws to fix the kit in the back chassis.
Wall mount:
14 Hardware and Installation
Page 21
GOT3187W-832-PCT User’s Manual
Back
VESA mount:
Hardware and Installation 15
Page 22
GOT3187W-832-PCT User’s Manual
Back
2.6.2 Panel-mount Kit Assembly
The GOT3187W-832-PCT is designed for panel mount application. To mount the GOT3187W-832-PCT, the standard set of mounting kit (included in the system packaging) is needed.
2.7 HDD Installation
The GOT3187W-832-PCT provides a convenient Hard Disk Drive (HDD) bracket for users to install 2.5 SATA HDD. Please follow the steps:
Step 1 Refer section 2.1 to open the back cover. Step 2 Fix the HDD on the HDD tray by 4 screws.
16 Hardware and Installation
Page 23
GOT3187W-832-PCT User’s Manual
Back
Step 3 Plug the cables to connectors and screw the HDD tray on the bracket.
Installation completes.
Hardware and Installation 17
Page 24
GOT3187W-832-PCT User’s Manual
Back
2.8 DRAM Installation
The GOT3187W-832-PCT provides one 204-pin DDR3 SODIMM socket that support system memory up to 4GB. Please follow steps below to install the memory modules:
Step 1 Refer to section 2.1 to open the back cover and find out DIMM socket on main
board (SBC87832).
Step 2 Stick the thermal pad on the back cover and rip the red mylar from it.
18 Hardware and Installation
Page 25
GOT3187W-832-PCT User’s Manual
Back
Step 3 Insert the DRAM to the DIMM socket, and then push it down firmly until it is
clipped by the socket.
Step 4 Installation completes.
Hardware and Installation 19
Page 26
GOT3187W-832-PCT User’s Manual
Back
2.9 Wireless LAN Card Installation
The GOT3187W-832-PCT provides one Mini card slot for user to install one wireless LAN card. When installing the wireless LAN card, refer to the following instructions and illustration:
Step 1 Refer to section 2.1 to open the back cover and find out mini-card slot on
main board.
Step 2 Insert the wireless LAN card to the slot. Push it down firmly until it is clipped
by the slot.
20 Hardware and Installation
Page 27
GOT3187W-832-PCT User’s Manual
Back
Step 3 Find the Antenna cable and connect it wireless LAN card.
….
Step 4 Remove the antenna plug from the top of back cover, and then install the
antenna on the antenna connector
Hardware and Installation 21
Page 28
GOT3187W-832-PCT User’s Manual
Back
2.10 Power Input
GOT3187W-832-PCT equips with a phoenix type power connector. It adopts 10VDC to 30VDC. Please follow the signs on power connector to connect DC power source.
+: Power positive G: Safety ground :Power negative
Note: The safety ground must be connected to ensure the unit working appropriately.
22 Hardware and Installation
Page 29
Back
This page is intentionally left blank.
GOT3187W-832-PCT User’s Manual
Hardware and Installation 23
Page 30
GOT3187W-832-PCT User’s Manual
Back
Hot Keys
Description
 Left/Right
The Left and Right <Arrow> keys allow you to select a setup screen.
 Up/Down
The Up and Down <Arrow> keys allow you to select a setup screen or sub-screen.
+ Plus/Minus
The Plus and Minus <Arrow> keys allow you to change the field value of a particular setup item.
Tab
The <Tab> key allows you to select setup fields.
F1
The <F1> key allows you to display the general help screen.
F2
The <F2> key allows you to load previous values.
F3
The <F3> key allows you to load optimized defaults.
F4
The <F4> key allows you to save any changes you have made and exit setup. Press the <F4> key to save your changes.
Esc
The <Esc> key allows you to discard any changes you have made and exit the setup. Press the <Esc> key to exit the setup without saving your changes.
Enter
The <Enter> key allows you to display or change the setup option listed for a particular setup item. The <Enter> key can also allow you to display the setup sub- screens.
Chapter 3
AMI BIOS Setup Utility
This chapter provides users with detailed description how to set up basic system configuration through the AMIBIOS BIOS setup utility.
3.1 Starting
To enter the setup screens, follow the steps below: Turn on the computer and press the <Del> key immediately. After you press the <Delete> key, the main BIOS setup menu displays. You can access the other setup screens from the main BIOS setup menu, such as the Chipset and Power menus.
3.2 Navigation Keys
The BIOS setup/utility uses a key-based navigation system called hot keys. Most of the BIOS setup utility hot keys can be used at any time during the setup navigation process. These keys include <F1>, <F2>, <Enter>, <ESC>, <Arrow> keys, and so on.
Note: Some of the navigation keys differ from one screen to another.
24 AMI BIOS Setup Utility
Page 31
GOT3187W-832-PCT User’s Manual
Back
3.3 Main Menu
When you first enter the Setup Utility, you will enter the Main setup screen. You can always return to the Main setup screen by selecting the Main tab. There are two Main Setup options. They are described in this section. The Main BIOS Setup screen is shown below
System Date/Time
Use this option to change the system time and date. Highlight System Time or System Date using the <Arrow> keys. Enter new values through the keyboard. Press the <Tab> key or the <Arrow> keys to move between fields. The date must be entered in MM/DD/YY format. The time is entered in HH:MM:SS format.
AMI BIOS Setup Utility 25
Page 32
GOT3187W-832-PCT User’s Manual
Back
3.4 Advanced Menu
Launch Storage OpROM
This item can enable or disable boot option for legacy mass storage devices with option ROM.
The Advanced menu also allows users to set configuration of the CPU and other system devices. You can select any of the items in the left frame of the screen to go to the sub menus:
ACPI Settings CPU Configuration IDE Configuration USB Configuration NCT6627UD Superior IO Configuration NCT6627UD HW Monitor JMB36X ATA Controller Configuration
For items marked with , please press <Enter> for more options.
26 AMI BIOS Setup Utility
Page 33
GOT3187W-832-PCT User’s Manual
Back
ACPI Settings
You can use this screen to select options for the ACPI Configuration, and change the value of the selected option. A description of the selected item appears on the right side of the screen.
ACPI Sleep State
Use this item to select the highest ACPI sleep state the system will enter.
AMI BIOS Setup Utility 27
Page 34
GOT3187W-832-PCT User’s Manual
Back
CPU Configuration
This screen shows the CPU Configuration, and you can change the value of the selected option.
Hyper-Threading
Use this item to enable or disable Hyper-Threading Technology, which makes a single physical processor perform multi-tasking function as two logical ones.
Execute Disable Bit
XD can prevent certain classes of malicious buffer overflow attacks when combined with a supporting OS (Windows Server 2003 SP1, Windows XP SP2, SuSE Linux 9.2, RedHat Enterprise 3 Update 3).
28 AMI BIOS Setup Utility
Page 35
Back
IDE Configuration
GOT3187W-832-PCT User’s Manual
SATA Controller(s)
The optional settings are: [Disabled]; [Enabled].
Configure SATA as
The optional settings are: [IDE]; [AHCI].
AMI BIOS Setup Utility 29
Page 36
GOT3187W-832-PCT User’s Manual
Back
USB Configuration
You can use this screen to select options for the USB Configuration, and change the value of the selected option. A description of the selected item appears on the right side of the screen.
Legacy USB Support
The optional settings are: [Auto]; [Disabled]; [Enabled].
30 AMI BIOS Setup Utility
Page 37
GOT3187W-832-PCT User’s Manual
Back
NCT6627UD Super IO Configuration
You can use this screen to select options for the Super IO Configuration, and change the value of the selected option. A description of the selected item appears on the right side of the screen
Serial Port Configuration
Use this item to set parameters of serial port 0~1
AMI BIOS Setup Utility 31
Page 38
GOT3187W-832-PCT User’s Manual
Back
PC Health Status
This screen shows the Hardware Health Configuration, and a description of the selected item appears on the right side of the screen.
32 AMI BIOS Setup Utility
Page 39
GOT3187W-832-PCT User’s Manual
Back
3.5 Chipset Menu
The Chipset menu allows users to change the advanced chipset settings. You can select any of the items in the left frame of the screen to go to the sub menus:
Host Bridge
Host Bridge For items marked with , please press <Enter> for more options.
South Bridge
South Bridge For items marked with , please press <Enter> for more options.
AMI BIOS Setup Utility 33
Page 40
GOT3187W-832-PCT User’s Manual
Back
Memory Information
This item is for memory frequency and timing settings. Press <Enter> to go to the sub menu.
34 AMI BIOS Setup Utility
Page 41
GOT3187W-832-PCT User’s Manual
Back
3.6 Boot Menu
The Boot menu allows users to change boot options of the system.
Boot Settings Configuration
Setup Prompt Timeout
Use this item to set number of seconds to wait for setup activation key.
Bootup NumLock State
Use this item to select the power-on state for the NumLock.. The optional settings are: [On]; [Off].
GateA20 Active
If Upon Request is selected, GA20 can be disabled using BIOS services. If Always is selected, disabling G20 is not allowed; this option is useful when any RT code is executed above 1MB.
Option ROM Messages
Set display mode for option ROM. Configuration options are Force BIOS and Keep Current.
Interrupt 19 Capture
If this item is enabled, this function makes the option ROM to trap Interrupt 19.
Boot Option Priorities
These are settings for boot priority. Specify the boot device priority sequence from the available devices.
AMI BIOS Setup Utility 35
Page 42
GOT3187W-832-PCT User’s Manual
Back
3.7 Security Menu
The Security menu allows users to change the security settings for the system.
Administrator Password
This item indicates whether an administrator password has been set. If the password has been installed, Installed displays. If not, Not Installed displays.
User Password
This item indicates whether an user password has been set. If the password has been installed, Installed displays. If not, Not Installed displays.
36 AMI BIOS Setup Utility
Page 43
GOT3187W-832-PCT User’s Manual
Back
3.8 Save & Exit Menu
The Save & Exit menu allows users to load your system configuration with optimal or fail-safe default values.
Save Changes and Exit
When you have completed the system configuration changes, select this option to leave Setup and reboot the computer so the new system configuration parameters can take effect. Select Save Changes and Exit from the Exit menu and press <Enter>. Select Ok to save changes and exit.
Discard Changes and Exit
Select this option to quit Setup without making any permanent changes to the system configuration. Select Discard Changes and Exit from the Exit menu and press <Enter>. Select Ok to discard changes and exit.
Save Changes and Reset
When you have completed the system configuration changes, select this option to leave Setup and reboot the computer so the new system configuration parameters can take effect. Select Save Changes and Reset from the Save & Exit menu and press <Enter>. Select Yes to save changes and reset.
Discard Changes and Reset
Select this option to quit Setup without making any permanent changes to the system configuration and reboot the computer. Select Discard Changes and Reset from the Save & Exit menu and press <Enter>. Select Yes to discard changes and reset.
Save Changes
When you have completed the system configuration changes, select this option to save changes. Select Save Changes from the Save & Exit menu and press <Enter>. Select yes to save changes.
AMI BIOS Setup Utility 37
Page 44
GOT3187W-832-PCT User’s Manual
Back
Discard Changes
Select this option to quit Setup without making any permanent changes to the system configuration. Select Discard Changes from the Save & Exit menu and press <Enter>. Select Yes to discard changes.
Restore Defaults
It automatically sets all Setup options to a complete set of default settings when you select this option. Select Restore Defaults from the Save & Exit menu and press <Enter>.
Save as User Defaults
Select this option to save system configuration changes done so far as User Defaults. Select Save as User Defaults from the Save & Exit menu and press <Enter>.
Restore User Defaults
It automatically sets all Setup options to a complete set of User Defaults when you select this option. Select Restore User Defaults from the Save & Exit menu and press <Enter>.
Boot Override
Select a drive to immediately boot that device regardless of the current boot order.
Note: If you want to use a CF card that capacity is less than 2GB (such as 1GB, 512MB),
we recommend you may switch “AHCI mode” to “IDE mode” with "Configure SATA as" of the BIOS setting. And please make sure your Operating System (Ex: Windows Embedded) is installed with “IDE” driver.
38 AMI BIOS Setup Utility
Page 45
Back
This page is intentionally left blank.
GOT3187W-832-PCT User’s Manual
AMI BIOS Setup Utility 39
Page 46
GOT3187W-832-PCT User’s Manual
Back
Touch Screen
Projected capacitive multi-touch
Touch Screen Controller
Mastouch USB Touch Screen Controller IC
Communications
USB interface
Power Supply
5V
Power Consumption
40mA
Input Method
Finger or Cap. Stylus
Resoulation
25PPI(Min.) Note: Base on WIN7 definition, PPI (Pixcel per inch)
Win7 USB Driver
Non-Driver
Calibration
Non-Calibration
Chapter 4
Drivers Installation
4.1 System
GOT3187W-832-PCT supports Windows 7 32-bit and WES 7. To facilitate the installation of system driver, please carefully read the instructions in this chapter before start installing.
Step 1 Insert Driver CD and select the \Driver.
Step 2 Select all files and follow the installing procedure.
4.2 Touch Screen
The GOT 3187W-832-PCT uses the projected capacitive multi-touch. The specification is listed below. It also can drive the touch panel to get two fingers touch function that based on the Windows 7 support.
Specification
Note: For the better system performance, please close the Windows AERO or change to
Windows Basic mode.
40 Drivers Installation
Page 47
GOT3187W-832-PCT User’s Manual
Back
4.3 Embedded O.S.
The GOT3187W-832-PCT provides the Windows 7 Embedded. The O.S. is supported devices which are listed below.
WES 7
Here are supported onboard devices:
Onboard Multi I/O SATA HDD USB CRT/LCD display 10/100/1000 base-T Ethernet Compact Flash Onboard Audio Touch Screen
NOTE: Causing of OS limitation, only single touch function is supported under WES 7E.
Drivers Installation 41
Loading...