AXIOMTEK GOT3157W-834-PCT User Manual

GOT3157W-834-PCT

All-in-One

15.6” WXGA TFT Fanless
Multi-Touch PANEL PC

User’s Manual

ii

Disclaimers

This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third
party’s rights, and any liability arising from such use.

Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make any
commitment to update the information in this manual.

Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.

No part of this document may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written permission of Axiomtek Co., Ltd.

CAUTION

If you replace wrong batteries, it causes the danger of explosion. It is recommended by the
manufacturer that you follow the manufacturer’s instructions to only replace the same or
equivalent type of battery, and dispose of used ones.

Copyright 2015 Axiomtek Co., Ltd.

All Rights Reserved
January 2015, Version A1
Printed in Taiwan

iii

Safety Precautions

Before getting started, read the following important cautions.

1. Be sure to ground yourself to prevent static charge when installing the internal
components. Use a grounding wrist strap and place all electronic components in any
static-shielded devices. Most electronic components are sensitive to static electrical
charge.

2. Disconnect the power cords from the GOT3157W-834-PCT Series before making any
installation. Be sure both the system and the external devices are turned OFF. Sudden
surge of power could ruin sensitive components. Make sure the GOT 3157W-834-PCT
Series is properly grounded.

3. Do not open the system’s rear cover. If opening the cover for maintenance is a must, only
a trained technician is allowed to do so. Integrated circuits on computer boards are
sensitive to static electricity. To avoid damaging chips from electrostatic discharge,
observe the following precautions:

 Before handling a board or integrated circuit, touch an unpainted portion of the

system unit chassis for a few seconds. This will help to discharge any static
electricity on your body.

 When handling boards and components, wear a wrist-grounding strap, available

from most electronic component stores.

Trademarks Acknowledgments

Axiomtek is a trademark of Axiomtek Co., Ltd.
Windows® is a trademark of Microsoft Corporation.

IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation.
Intel® and Pentium® are trademarks of Intel Corporation.

AMI is trademark of American Megatrend Inc.
Other brand names and trademarks are the properties and registered brands of their

respective owners.

iv

Table of Contents

Disclaimers ..................................................................................................... ii

Safety Precautions ........................................................................................ iii

Chapter 1 Introduction ............................................. 1

1.1 General Description ............................................................................ 1

1.2 Specifications ...................................................................................... 2

1.3 Dimensions and Outlines ................................................................... 4

1.4 I/O Outlets ............................................................................................ 6

1.5 Packing List ......................................................................................... 7

Chapter 2 Hardware and Installation ...................... 9

2.1 CFast

TM

card Installation ................................................................... 10

2.2 Open back cover ............................................................................... 11

2.3 Jumper and Switch Setting .............................................................. 12

2.3.1 Auto Power On (JP7) ................................................................................ 12

2.3.2 Restore BIOS Optimal Defaults (JP8) ....................................................... 12

2.3.3 COM port Connector ................................................................................. 13

2.4 Ethernet .............................................................................................. 14

2.5 Mountings: Panel / Wall / Desktop / VESA ...................................... 15

2.5.1 VESA-ARM/Wall-Mount ............................................................................ 15

2.5.2 Panel-mount Kit Assembly ........................................................................ 16

2.6 HDD Installation ................................................................................. 17

2.7 DRAM Installation .............................................................................. 19

2.8 Wireless LAN Card Installation ........................................................ 20

2.9 Power Input ........................................................................................ 22

Chapter 3 AMI BIOS Setup Utility .......................... 23

3.1 Navigation Keys ................................................................................ 23

3.2 Main Menu .......................................................................................... 24

3.3 Advanced Menu ................................................................................. 25

3.4 Chipset Menu ..................................................................................... 36

3.5 Security .............................................................................................. 43

3.6 Boot Menu .......................................................................................... 44

3.7 Save&Exit ........................................................................................... 45

v

Chapter 4 Drivers Installation ................................ 47

4.1 System ............................................................................................... 47

4.1.1 Win 7 ......................................................................................................... 47

4.1.2 Win 8/8.x ................................................................................................... 48

4.2 Touch Screen ..................................................................................... 49

4.3 Embedded O.S. .................................................................................. 50

4.3.1 WES 7 & WE8S ......................................................................................... 50

vi

This page is intentionally left blank.

GOT3157W-834-PCT User’s Manual

Introduction 1

Chapter 1

Introduction

This chapter contains general information and detailed specifications of the
GOT3157W-834-PCT. Chapter 1 includes the following sections:

 General Description
 Specifications
 Dimensions and outlines
 I/O Outlets
 Package List

1.1 General Description

The GOT3157W-834-PCT adopts a 15.6-inch WXGA TFT LCD with 400-nit brightness and an
Intel® Celeron® Processor J1900 (2M Cache, up to 2.42 GHz) to provide excellent computing
performance and thermal resistance. This fanless platform is especially designed for
operating under harsh environment including steel refinery, oil pipe, ship, machine maker
operating systems and many more. Having below abilities makes GOT3157W-834-PCT
surely a most robust and cost-effective solution.

Extended Operating Temperature Range with Fanless & IP65 front design

GOT3157W-834-PCT features a technology of extended operating temperature range which
allows it to work between -10°C to +50°C. It incorporates compact ID and fanless cooling
system with a low power Intel® Celeron® Processor J1900 (2M Cache, up to 2.42 GHz), IP65
front bezel to prevent from liquid or dust, making the platform a power-efficient solution.

Reliable and Stable Design

The GOT3157W-834-PCT adopts a fan-less cooling system, which makes it especially
suitable for vibration-heavy environments, best for the transportation, ship, and industrial
machinery markets. For high capacity storage requirement, GOT3157W-834-PCT can work
under 2.0G (10 ~ 500Hz, random for CFast™) in operation mode with a patent of anti-vibration
design. The patent improves the system reliability and sustainability.(Note: Sometimes
heavy-vibration may cause the LCD screen flash with white color. It won’t affect product
function.)

GOT3157W-834-PCT User’s Manual

2 Introduction

WLAN Antenna Supported (optional)

GOT3157W-834-PCT has 2 PCI Express Mini Card slots for optional add-on such as wireless
LAN card for 802.11 a/b/g/n connections, 3G/GPRS application, and more. These slots also
provide 3 optional fixed rotational WLAN/3G antennas for wireless network connection.

Multi-Touch PCAP touch with 7H surface hardness

It is designed with user friendly multi-touch PCAP touch. Users can operation it directly. The
surface hardness is up to 7H and is good for anti-scratch purpose applications.

More Features

GOT3157W-834-PCT utilizes one 204-pin DDR3L SODIMM system memory max. up to 8GB,
one SATA HDD and one CFast™ or mSATA. It provides over-current protection-fuse and a
full set of I/O including RS-232/422/485, USB 2.0, USB 3.0, audio (line-out), and Gigabit
Ethernet. Additionally, this slim unit supports panel mount, wall mount (optional), VESA
mount (optional) and desktop stand (optional).

1.2 Specifications

Main CPU Board

 CPU

 Intel® Celeron® Processor J1900 (2M Cache, up to 2.42 GHz) onboard

 System Memory

 One 204-pin DDR3L SO-DIMM socket
 Maximum memory up to 8GB

 BIOS

 America Megatrends BIOS

I/O System

 Standard I/O

 2 x RS-232/422/485
 2 x USB 2.0
 2 x USB 3.0

 Ethernet

 2 x RJ45 for Giga Ethernet (Intel i210IT)

 Audio

 1x Line-out

 Expansion

 1 x Mini-card slot (w/SIM slot)
 1 x Mini-card slot (supports mSATA, optional)

 Storage

 1 x 2.5” SATA
 1 x CFast

TM

slot or mSATA

 Power connector

 Phoenix power connector or Screw power connector

GOT3157W-834-PCT User’s Manual

Introduction 3

System Specification

 15.6” WXGA (1366x768) LCD with LED backlight
 Multi-touch PCAP touch
 Fanless Heat Dispensing Design
 IP65 front bezel
 Disk drive housing:

 One 2.5” SATA drive

 Net Weight

 5.0 Kgs

 Dimension (Main Body Size)

 396.8 x 53.9x 247.1 mm

 Operation Temperature

 -10℃ to 50℃

 Relative Humidity

 20% to 90% @ 40℃, Non-Condensing

 System Power input

 DC power input : 9~36VDC with phoenix power connector
 AC power input : 12VDC, 60W power adapter

NOTE: All specifications and images are subject to change without notice.

If the operation temperature is higher than 40℃, the wide temperature HDD/
CFastTM are recommended to be used on the device.

If the operation temperature is higher than 45℃, the wide temperature DRAM is
recommended to be used on the device.

GOT3157W-834-PCT User’s Manual

4 Introduction

1.3 Dimensions and Outlines

The following diagrams show the dimensions and outlines of GOT3157W-834-PCT

Outline dimension: 396.8 x 59.4x 247.1 mm

GOT3157W-834-PCT User’s Manual

Introduction 5

Cut Out dimensions: 385.6 x 235.9 mm

GOT3157W-834-PCT User’s Manual

6 Introduction

1.4 I/O Outlets

Please refer to the following illustration for I/O locations of the GOT3157W-834-PCT.

GOT3157W-834-PCT User’s Manual

Introduction 7

1.5 Packing List

When you receive the GOT3157W-834-PCT, the bundled package should contain the
following items:

 GOT3157W-834-PCT unit x 1
 Driver Disc x1
 Phoenix connector x 1 ( DC power version only)
 Panel mount kit x 9
 Screws for HDD x 4
 SATA data cable x 1
 SATA power cable x 1

If you can not find the package or any items are missing, please contact Axiomtek distributors
immediately.

GOT3157W-834-PCT User’s Manual

8 Introduction

This page is intentionally left blank.

GOT3157W-834-PCT User’s Manual

Hardware and Installation 9

Chapter 2

Hardware and Installation

The GOT3157W-834-PCT provides rich I/O ports and flexible expansions for you to meet
different demand, for example CF card. The chapter will show you how to install the hardware.
It includes:

 CFast™ Card
 Open Back Cover
 Jumper and Switch Setting
 Ethernet
 Mounting Method
 Hard disk
 DRAM
 Wireless LAN Card
 Power Input

GOT3157W-834-PCT User’s Manual

10 Hardware and Installation

2.1 CFast

TM

card Installation

The GOT3157W-834-PCT provides one CFast™slot for users to install CFast™ card. Please
refer to the following instructions for installation:

Step 1 Open the CFast card slot cover, unscrew 2 screws on the chassis.

Step 2 Install the CFast card to the CFast card slot.

Step 3 Screw the CFast cover slot cover with 2 screws..

GOT3157W-834-PCT User’s Manual

Hardware and Installation 11

2.2 Open back cover

This section tells users how to open back cover. Please follow the steps below.

Step 1 Unscrew 8 screws on the back cover. Please refer the photo below.

Step 2 Remove the back cover.

GOT3157W-834-PCT User’s Manual

12 Hardware and Installation

2.3 Jumper and Switch Setting

Jumper is a small component consisting of jumper clip and jumper pins. Install jumper clip on 2
jumper pins to close. And remove jumper clip from 2 jumper pins to open. The following
illustration shows how to set up jumper.

Before applying power to GOT3157W-834-PCT, please make sure all of the jumpers and
switch are in factory default position. Below you can find a summary table and onboard default
settings.

Jumper

Description

Setting

JP7

Auto Power On
Default: Disable

2-3 close

JP8

Restore BIOS Optimal Defaults (Clear CMOS)
Default: Normal Operation

1-2 close

JP6

Switches mSATA or CFastTM setting.
Default: 1-2 = CFast™, 2-3 = mSATA

1-2 close

2.3.1 Auto Power On (JP7)

If JP7 is enabled for power input, the system will be automatically power on without pressing
soft power button. If JP7 is disabled for power input, it is necessary to manually press soft
power button to power on the system.

2.3.2 Restore BIOS Optimal Defaults (JP8)

Put jumper clip to pin 2-3 for a few seconds then move it back to pin 1-2. Doing this procedure
can restore BIOS optimal defaults.

Function

Setting

Enable auto power on

1-2 close

Disable auto power on
(Default)

2-3 close

Function

Setting

Normal operation (Default)

1-2 close

Restore BIOS optimal defaults

2-3 close

GOT3157W-834-PCT User’s Manual

Hardware and Installation 13

2.3.3 COM port Connector

The pin assignment of RS-232/RS-422/RS-485 is listed on the following table.

Pin

RS-232

RS-422

RS-485

1

DCD

TX-

Data-

2

RXD

TX+

Data+

3

TXD

RX+

No use

4

DTR

RX-

No use

5

GND

GND

GND

6

DSR

No use

No use

7

RTS

No use

No use

8

CTS

No use

No use

9

RI

No use

No use

GOT3157W-834-PCT User’s Manual

14 Hardware and Installation

2.4 Ethernet

The GOT3157W-834-PCT is equipped with a high performance Plug and Play Ethernet
interface, full compliant with IEEE 802.3 standard, and can be connected with a RJ-45 LAN
connector.
Please refer to detailed pin assignment list below:

Pin

Signal

1

2345678

RJ-45

1

TX+ (Data transmission positive

2

TX- (Data transmission negative)

3

Rx+(Data reception positive)

4

RJ45 termination

5

RJ45 termination

6

Rx- (Data reception negative)

7

RJ45 termination

8

RJ45 termination

GOT3157W-834-PCT User’s Manual

Hardware and Installation 15

2.5 Mountings: Panel / Wall / Desktop / VESA

There are 4 application options for the GOT3157W-834-PCT, Panel/Wall/Desktop/VESA
mountings.

2.5.1 VESA-ARM/Wall-Mount

The GOT3157W-834-PCT provides VESA mount: 100x100 mm. Screw four screws to fix the
kit in the back chassis.

Wall mount kit (optional):

VESA mount:

GOT3157W-834-PCT User’s Manual

16 Hardware and Installation

2.5.2 Panel-mount Kit Assembly

The GOT3157W-834-PCT is designed for panel mount application. To mount the
GOT3157W-834-PCT, the standard set of mounting kit (included in the system packaging) is
needed.

GOT3157W-834-PCT User’s Manual

Hardware and Installation 17

2.6 HDD Installation

The GOT3157W-834-PCT provides a convenient Hard Disk Drive (HDD) bracket for users to
install 2.5” SATA HDD. Please follow the steps:

Step 1 Refer section 2.2 to open the back cover & dissemble the HDD tray by un-screw

4 screws.

Step 2 Fix the HDD on the HDD tray by 4 screws.

GOT3157W-834-PCT User’s Manual

18 Hardware and Installation

Step 3 Plug the cables to connectors and screw the HDD tray on the bracket.

Installation completes.

GOT3157W-834-PCT User’s Manual

Hardware and Installation 19

2.7 DRAM Installation

The GOT3157W-834-PCT provides one 204-pin DDR3L SODIMM socket that supports system
memory up to 8GB. Please follow steps below to install the memory modules:

Step 1 Refer to section 2.2 to open the back cover.

Step 2 Find out DIMM socket on mainboard (SBC87834).

Step 3 Insert the DRAM to the DIMM socket, and then push it down firmly until it is

clipped by the socket.

Installation completed

GOT3157W-834-PCT User’s Manual

20 Hardware and Installation

2.8 Wireless LAN Card Installation

The GOT3157W-834-PCT provides one Mini card slot for user to install one wireless LAN card.
When installing the wireless LAN card, refer to the following instructions and illustration:

Step 1 Refer to section 2.2 to open the back cover and find out mini-card slot on

mainboard.

Step 2 Insert the wireless LAN card to the slot. Push it down firmly until it is clipped

by the slot.



GOT3157W-834-PCT User’s Manual

Hardware and Installation 21

Step 3 Find the Antenna cable and connect it on wireless LAN card.

….

GOT3157W-834-PCT User’s Manual

22 Hardware and Installation

Step 4 Remove the antenna plug from the top of back cover, and then install the

antenna on the antenna connector

NOTE: Please have the extended bracket when using half-size mini card.

2.9 Power Input

GOT3157W-834-PCT equips with a phoenix type power connector. It adopts 9VDC to 36VDC.
Please follow the signs on power connector to connect DC power source.

+: Power positive G: Safety ground －:Power negative

NOTE: The safety ground must be connected to ensure the unit working appropriately.

GOT3157W-834-PCT User’s Manual

AMI BIOS Setup Utility 23

Chapter 3

AMI BIOS Setup Utility

This chapter provides users with detailed description how to set up basic system configuration
through the AMIBIOS8 BIOS setup utility.

3.1 Navigation Keys

The BIOS setup/utility uses a key-based navigation system called hot keys. Most of the BIOS
setup utility hot keys can be used at any time during the setup navigation process.
These keys include <F1>, <F2>, <F3>, <F4>, <Enter>, <ESC>, <Arrow> keys, and so on.

NOTE: Some of navigation keys differ from one screen to another.

 Left/Right

The Left and Right <Arrow> keys allow you to select a setup screen.

 Up/Down

The Up and Down <Arrow> keys allow you to select a setup screen or sub-screen.

+ Plus/Minus

The Plus and Minus <Arrow> keys allow you to change the field value of a particular
setup item.

Tab

The <Tab> key allows you to select setup fields.

F1

The <F1> key allows you to display the General Help screen.

F2

The <F2> key allows you to load previous value

F3

The <F3> key allows you to Load Optimized Defaults.

F4

The <F4> key allows you to save any changes you have made and exit Setup.
Press the <F4> key to save your changes.

Esc

The <Esc> key allows you to discard any changes you have made and exit the
Setup. Press the

<Esc> key to exit the setup without saving your changes.

Enter

The <Enter> key allows you to display or change the setup option listed for a
particular setup item. The <Enter> key can also allow you to display the setup sub­screens.

GOT3157W-834-PCT User’s Manual

24 AMI BIOS Setup Utility

3.2 Main Menu

System Date / Time

Use this option to change the system time and date. Highlight System Time or System Date
using the <Arrow> keys. Enter new values through the keyboard. Press the <Tab> key or the
<Arrow> keys to move between fields. The date must be entered in MM/DD/YY format. The
time is entered in HH:MM:SS format.

GOT3157W-834-PCT User’s Manual

AMI BIOS Setup Utility 25

3.3 Advanced Menu

The Advanced menu allows users to set configuration of the CPU and other system devices.
You can select any of the items in the left frame of the screen to go to the sub menus:

 ACPI Settings
 NCT6106D Super IO Configuration
 NCT6106D H/W Monitor
 CPU Configuration
 IDE Configuration
 LPSS & SCC Configuration
 USB Configuration
 Security Configuration

For items marked with “”, please press <Enter> for more options.’

GOT3157W-834-PCT User’s Manual

26 AMI BIOS Setup Utility

ACPI Settings

You can use this screen to select options for the ACPI Configuration, and change the value of
the selected option. A description of the selected item appears on the right side of the screen.

ACPI Sleep State

Allow you to select the Advanced Configuration and Power Interface (ACPI) state to be used
for system suspend. Here are the options for your selection, Suspend disable and S3
(Suspend to RAM).

GOT3157W-834-PCT User’s Manual

AMI BIOS Setup Utility 27

NCT6106D Super IO Configuration

Use this screen to select options for the Super IO Configuration, and change the value of the
selected option

GOT3157W-834-PCT User’s Manual

28 AMI BIOS Setup Utility

Serial Port 1-2 configuration
Serial port:

This option used to enable or disable the serial port.

Device Setting:

This item specifies the base I/O port address and Interrupt Request address of serial port.
The port 0 Optimal setting is 3F8/IRQ4.
The port 1 Optimal setting is 2F8/IRQ3.

GOT3157W-834-PCT User’s Manual

AMI BIOS Setup Utility 29

Serial type:

This option used to select RS232/422/485 function.

GOT3157W-834-PCT User’s Manual

30 AMI BIOS Setup Utility

NCT6106D H/W Monitor

This screen shows the Hardware Health Configuration.

GOT3157W-834-PCT User’s Manual

AMI BIOS Setup Utility 31

CPU Configuration

These screens show the CPU Configuration, CPU information and Intel virtualization
technology enable/disable selected

GOT3157W-834-PCT User’s Manual

32 AMI BIOS Setup Utility

GOT3157W-834-PCT User’s Manual

AMI BIOS Setup Utility 33

IDE Configuration

You can use this screen to select options for the SATA Configuration, and change the value of
the selected option.

SATA Mode

Use this item to choose the SATA operation mode. Here are the options for your selection, IDE
Mode, AHCI Mode.

GOT3157W-834-PCT User’s Manual

34 AMI BIOS Setup Utility

Intel TXE Configuration

The Advanced menu allows users to update the TXE firmware.

GOT3157W-834-PCT User’s Manual

AMI BIOS Setup Utility 35

LPSS & SCC Configuration

You can select any of the items in the frame of the screen to change the OS, the default setting
is Windows 7.

Please be informed to select the Windows 8.x when installing Win 8 or Win 8.1.

If using the Android OS, please refer to https://01.org/android-ia.

GOT3157W-834-PCT User’s Manual

36 AMI BIOS Setup Utility

3.4 Chipset Menu

The Chipset menu allows users to change the advanced chipset settings.

GOT3157W-834-PCT User’s Manual

AMI BIOS Setup Utility 37

 North Bridge

This screen shows the North Bridge memory information.

GOT3157W-834-PCT User’s Manual

38 AMI BIOS Setup Utility

 South Bridge

GOT3157W-834-PCT User’s Manual

AMI BIOS Setup Utility 39

 USB Configuration

You can use this screen to select options for the USB Configuration,
If USB3.0 function used, XHCI Mode must enable and EHCI must disable.
**XHCI default is Auto.

GOT3157W-834-PCT User’s Manual

40 AMI BIOS Setup Utility

To “Enabled” or “Disabled” USB Mass Storage Driver Support

GOT3157W-834-PCT User’s Manual

AMI BIOS Setup Utility 41

USB hardware delays and time-outs:

GOT3157W-834-PCT User’s Manual

42 AMI BIOS Setup Utility

GOT3157W-834-PCT User’s Manual

AMI BIOS Setup Utility 43

3.5 Security

The Security menu allows users to change the security settings for the system.

GOT3157W-834-PCT User’s Manual

44 AMI BIOS Setup Utility

3.6 Boot Menu

The Boot menu allows users to change boot options of the system. You can select any of the
items in the left frame of the screen to go to the sub menus:

Setup Prompt Timeout

Set the Timeout for wait press key to enter Setup Menu.

Quiet Boot

Use this item to enable or disable the Quite Boot state. The default setting is disable.

Legacy Pxe OPROM

Use this item to enable or disable the Preboot Execution Environment. The default setting is
disable.

Boot Option Priorities

Specifies the overall boot order from the available devices.

GOT3157W-834-PCT User’s Manual

AMI BIOS Setup Utility 45

3.7 Save&Exit

Save Changes and Exit

When you have completed the system configuration changes, select this option to leave Setup
and reboot the computer so the new system configuration parameters can take effect. Select
Save Changes and Exit from the Exit menu and press <Enter>. Select Ok to save changes
and exit.

Discard Changes and Exit

Select this option to quit Setup without making any permanent changes to the system
configuration. Select Discard Changes and Exit from the Exit menu and press <Enter>. Select
Ok to discard changes and exit.

Save Changes and Reset

When you have completed the system configuration changes, select this option to leave Setup
and reboot the computer so the new system configuration parameters can take effect. Select
Save Changes and Reset from the Save & Exit menu and press <Enter>. Select Yes to save
changes and reset.

Discard Changes and Reset

Select this option to quit Setup without making any permanent changes to the system
configuration and reboot the computer. Select Discard Changes and Reset from the Save &
Exit menu and press <Enter>. Select Yes to discard changes and reset.

Save Changes

When you have completed the system configuration changes, select this option to save
changes. Select Save Changes from the Save & Exit menu and press <Enter>. Select yes to
save changes.

GOT3157W-834-PCT User’s Manual

46 AMI BIOS Setup Utility

Discard Changes

Select this option to quit Setup without making any permanent changes to the system
configuration. Select Discard Changes from the Save & Exit menu and press <Enter>. Select
Yes to discard changes.

Restore Defaults

It automatically sets all Setup options to a complete set of default settings when you select this
option. Select Restore Defaults from the Save & Exit menu and press <Enter>.

Save as User Defaults

Select this option to save system configuration changes done so far as User Defaults. Select
Save as User Defaults from the Save & Exit menu and press <Enter>.

Restore User Defaults

It automatically sets all Setup options to a complete set of User Defaults when you select this
option. Select Restore User Defaults from the Save & Exit menu and press <Enter>.

Boot Override

Select a drive to immediately boot that device regardless of the current boot order.

GOT3157W-834-PCT User’s Manual

Drivers Installation 47

Chapter 4

Drivers Installation

4.1 System

GOT3157W-834-PCT supports Windows 7, Windows 8/8.1 ,WES 7 and WE8S. To facilitate
the installation of system driver, please carefully read the instructions in this chapter before
start installing.

4.1.1 Win 7

1. Insert Driver Disc and select the “\Drivers”.

2. Select all files and follow the installing procedure. Please don’t run Step 7 that is driver
for resistive touch screen.

NOTE: Please install Microsoft KB2685811 before TXE installation under Windows 7, then

installing the drivers.

NOTE: Without “Graphic driver” installed and let GOT3157W-834-PCT idle for a while, will

cause “Power Management” program to turn off GOT3157W-834-PCT LCD monitor.

It is unable to wake up the LCD monitor of GOT3157W-834-PCT.You need to reboot
GOT3157W-834-PCT and install “Graphic driver” correctly. There will be no such
display problem.

GOT3157W-834-PCT User’s Manual

48 Drivers Installation

4.1.2 Win 8/8.x

1. Insert Driver Disc and select the “\Drivers”.

2. Select all files and follow the installing procedure. Please don’t run Step 7 that is driver for

resistive touch screen.

NOTE: Without “Graphic driver” installed and let GOT3157W-834-PCT idle for a while, will

cause “Power Management” program to turn off GOT3157W-834-PCT LCD monitor. It

is unable to wake up the LCD monitor of GOT3157W-834-PCT.You need to reboot
GOT3157W-834-PCT and install “Graphic driver” correctly. There will be no such
display problem.

GOT3157W-834-PCT User’s Manual

Drivers Installation 49

4.2 Touch Screen

The GOT3157W-834-PCT uses the projected capacitive multi-touch. The specification is listed
below. The touch driver will be installed automatically and can drive the touch panel to get two
fingers touch function that based on the Windows 7 and Windows 8.x support.

 Specification

Touch Screen

Projected capacitive multi-touch

Touch Screen Controller

Mastouch USB Touch Screen Controller IC

Communications

USB interface

Power Supply

5V

Power Consumption

40mA

Input Method

Finger or Cap.Stylus

Resolution

25ppi(Min.)
Note: Base on WIN7 definition, ppi(Pixcel per inch)

Win7 USB Driver

Non-Driver

Calibration

Non-Calibration

GOT3157W-834-PCT User’s Manual

50 Drivers Installation

4.3 Embedded O.S.

The GOT3157W-834-PCT provides the WES 7 and WE8S Embedded. The O.S. is supported
devices which are listed below.

4.3.1 WES 7 & WE8S

Here are supported onboard devices:

 Onboard Multi I/O
 SATA HDD
 USB
 LCD display
 10/100/1000 base-T Ethernet
 CFast

TM

or mSATA

 Onboard Audio

NOTE: Causing of OS limitation, only single touch function is supported under WES 7E.