AXIOMTEK GOT3156T-832 User Manual

GOT3156T-832

All-in-One
15” XGA TFT Fanless
Compact-Size PANEL PC

User’s Manual

Disclaimers

This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third
party’s rights, and any liability arising from such use.

Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make
any commitment to update the information in this manual.

Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.

No part of this document may be reproduced, stored in a retrieval system, or transmitted,
in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, without the prior written permission of Axiomtek Co., Ltd.

CAUTION

If you replace wrong batteries, it causes the danger of explosion. It is recommended by
the manufacturer that you follow the manufacturer’s instructions to only replace the same
or equivalent type of battery, and dispose of used ones.

Copyright 2013 Axiomtek Co., Ltd.

All Rights Reserved
August 2013, Version A2
Printed in Taiwan

ii

Safety Precautions

Before getting started, read the following important cautions.

1. Be sure to ground yourself to prevent static charge when installing the internal
components. Use a grounding wrist strap and place all electronic components in any
static-shielded devices. Most electronic components are sensitive to static electrical
charge.

2. Disconnect the power cords from the GOT3156T-832 Series before making any
installation. Be sure both the system and the external devices are turned OFF. Sudden
surge of power could ruin sensitive components. Make sure the GOT3156T-832 Series is
properly grounded.

3. Do not open the system’s top cover. If opening the cover for maintenance is a must, only
a trained technician is allowed to do so. Integrated circuits on computer boards are
sensitive to static electricity. To avoid damaging chips from electrostatic discharge,
observe the following precautions:

 Before handling a board or integrated circuit, touch an unpainted portion of the

system unit chassis for a few seconds. This will help to discharge any static
electricity on your body.

 When handling boards and components, wear a wrist-grounding strap, available

from most electronic component stores.

Trademarks Acknowledgments

Axiomtek is a trademark of Axiomtek Co., Ltd.
Windows® is a trademark of Microsoft Corporation.

IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation.
Intel® and Atom™ are trademarks of Intel Corporation.

AMI is trademark of American Megatrend Inc.
Other brand names and trademarks are the properties and registered brands of their

respective owners.

iii

Table of Contents

CHAPTER 1 INTRODUCTION .............................................................................. 1

CHAPTER 2 HARDWARE AND INSTALLATION ...................................................... 7

2.1 OPEN BACK COVER ............................................................................................... 8

2.2 CF CARD INSTALLATION ......................................................................................... 9

2.3 JUMPER AND SWITCH SETTINGS ........................................................................... 10

2.4 COM PORT CONNECTOR ................................................................................... 12

2.5 ETHERNET ....................................................................................................... 13

2.6 MOUNTINGS: PANEL / WALL / VESA ................................................................... 13

2.7 HDD INSTALLATION ........................................................................................... 15

2.8 DRAM INSTALLATION ........................................................................................ 17

2.9 WIRELESS LAN CARD INSTALLATION ..................................................................... 19

2.10 POWER INPUT .................................................................................................. 21

CHAPTER 3 AMI BIOS SETUP UTILITY ................................................................ 23

3.1 STARTING......................................................................................................... 23

3.2 NAVIGATION KEYS ............................................................................................. 23

3.3 MAIN MENU .................................................................................................... 24

3.4 ADVANCED MENU ............................................................................................. 25

3.5 CHIPSET MENU ................................................................................................. 32

3.6 BOOT MENU .................................................................................................... 34

3.7 SECURITY MENU ............................................................................................... 35

3.8 SAVE & EXIT MENU ........................................................................................... 36

CHAPTER 4 DRIVERS INSTALLATION ................................................................ 39

4.1 SYSTEM ........................................................................................................... 39

4.2 TOUCH SCREEN ................................................................................................. 39

4.3 EMBEDDED O.S. ............................................................................................... 41

iv

This page is intentionally left blank.

v

GOT3156T-832 User’s Manual

Back

Chapter 1

Introduction

This chapter contains general information and detailed specifications of the
GOT3156T-832. Chapter 1 includes the following sections:

 General Description
 Specification
 Dimensions
 I/O Outlets
 Package List

1.1 General Description

The GOT3156T-832 adopts a 15-inch XGA TFT LCD with 450-nit brightness and
an Intel® AtomTM processor N2600 1.6 GHz to provide excellent computing
performance and thermal resistance. This fanless platform is especially designed
for operating under heavy-duty environment including steel refinery, oil pipe, ship,
machine maker operating systems and many more. Having below abilities makes
GOT3156T-832 surely a most robust and cost-effective solution.

Wide Operating Temperature Range

GOT3156T-832 features a technology of wide operating temperature range which
allows it to work between -20°C to +55°C. It incorporates compact ID and fanless
cooling system with a low power Intel® AtomTM processor N2600 1.6 GHz,
making the platform a power-efficient solution.

Introduction 1

GOT3156T-832 User’s Manual

Back

Reliable and Stable Design

The GOT3156T-832 adopts a fan-less cooling system and a CompactFlash™ card,
which makes it especially suitable for vibration-heavy environments, best for the
transportation, ship, and industrial machinery markets. For high capacity storage
requirement, GOT3156T-832 can work under 1.3G (10 ~ 500Hz, random for 2.5”
HDD) in operation mode with a patent of anti-vibration design. The patent
improves the system reliability and sustainability.

WLAN Antenna Supported (optional)

GOT3156T-832 has a PCI Express Mini Card slot for optional add-ons such as
wireless LAN card for 802.11 b/g connections & 3G/GPRS application,
graphics-enhanced video card, universal analog TV/FM tuner/AV capture card, and
more. It also provides an optional fixed rotational WLAN antenna for wireless
network connection.

More Features

GOT3156T-832 utilizes one 204-pin DDR3 SODIMM system memory max. up to
2GB, one SATA HDD and one CompactFlashTM slot. It provides over-current
protection-fuse and a full set of I/O including 3 RS-232, 1 RS-232/422/485, 4 USB

2.0, 1 audio (line-out), 2 Gigabit Ethernet and 1 VGA. Additionally, this slim unit
supports panel mount, wall mount (optional), VESA mount (optional) and desktop
stand (optional).

1.2 Specifications

Main CPU Board

 CPU

 Intel

 System Chipset

 Intel

 System Memory

 One 204-pin DDR3 SO-DIMM socket
 Maximum memory up to 2GB

 BIOS

 America Megatrends BIOS

I/O System

 Standard I/O

 Three RS-232 and one RS-232/422/485
 Four USB 2.0

®

AtomTM N2600 1.6GHz processor onboard

®

NM10 Express

2 Introduction

Back

 Ethernet

 Two Gigabit Ethernet

 Audio

 One Line-out

 Expansion

 One Mini card

 Storage

 One slot for CF card
 One SATA

 Power connector

 Phoenix power connector

System Specification

 15” XGA(1024x768) LCD with LED backlight
 5 wired resistive Touch

GOT3156T-832 User’s Manual

 Fanless Heat Dispensing Design
 IP65 aluminum front bezel
 Disk drive housing:

 One 2.5” SATA drive

 Net Weight

 7.4 Kgs (16.44 lb)

 Dimension (Main Body Size)

 378mm x 60.7mm x 309mm

 Operation Temperature

 -20℃ to 55℃

 Relative Humidity

 20% to 90% @ 40℃, Non-Condensing

 Power input

 DC power 10~30V (phoenix type)

Note: All specifications and images are subject to change without notice.

Note: If the operation temperature is higher than 40℃, the wide temperature HDD

is recommended to be used on the device, and it is higher than 45℃, the wide
temperature CF or SSD is recommended to be used on the device.

Introduction 3

GOT3156T-832 User’s Manual

Back

1.3 Dimensions and Outlines

The following diagrams show the dimensions and outlines of GOT3156T-832.

4 Introduction

GOT3156T-832 User’s Manual

Back

No

Function

No

Function

1

POWER SWITCH (ATX)

7

COM 1 (RS-232/422/485)

2

Power Input connector (phoenix)

8

COM 2 (RS-232)

3

COM 4 (RS-232)

9

Ethernet (RJ-45)

4

COM 3 (RS-232)

10

Dual USB 2.0 ports

5

Dual USB 2.0 ports

11

AUDIO (LINE-OUT)

6

VGA

1.4 I/O Outlets

Please refer to the following illustration for I/O locations of the GOT3156T-832.

Introduction 5

GOT3156T-832 User’s Manual

Back

1.5 Packing List

When you receive the GOT3156T-832, the bundled package should contain the
following items:

 GOT3156T-832 unit x 1
 Driver CD x 1
 Phoenix connector x 1
 Panel mount kit x 9
 Screws for HDD x 4

If you cannot find the package or any items are missing, please contact Axiomtek
distributors immediately.

6 Introduction

GOT3156T-832 User’s Manual

Back

Chapter 2

Hardware and Installation

The GOT3156T-832 provides rich I/O ports and flexible expansions for you to meet different
demand, for example CF card. The chapter will show you how to install the hardware. It
includes:

 Open back cover
 CompactFlash™ Card
 Serial Port
 Ethernet
 Mounting Method
 Hard disk
 DRAM
 Wireless LAN Card
 Power

Hardware and Installation 7

GOT3156T-832 User’s Manual

Back

2.1 Open back cover

This section tells users how to open back cover. Please follow the steps below.

Step 1 Unscrew 14 screws on the back cover. Please refer the photo below.

Step 2 Remove the back cover.

8 Hardware and Installation

GOT3156T-832 User’s Manual

Back

2.2 CF card Installation

The GOT3156T-832 provides one CF slot for users to install CompactFlash™ card. Please
refer to the following instructions for installation:

Step 1 Unscrew a screw on the cover of CF card slot on left side of GOT.

Step 2 Stick mylar on the CF card.

Step 3 Insert the card into the socket.

Step 4 Close the cover of CF card slot and fix it. Installation completes.

Hardware and Installation 9

GOT3156T-832 User’s Manual

Back

Jumper

Description

Setting

JP4

Auto Power On
Default: Disable

2-3 close

JP5

CF Voltage Selection
Default: +3.3V

1-2 close

JP6

Restore BIOS Optimal Defaults (Clear CMOS)
Default: Normal Operation

1-2 close
JP7

COM1 RS-232/422/485 Mode Setting
Default: RS-232

3-5, 4-6 close

JP8

3-5, 4-6 close

JP9

1-2 close

JP10

COM1 Data/Power Selection
Default: RS-232 Data

Pin 1: DCD

3-5 close

Pin 9: RI

4-6 close

JP11

COM2 Data/Power Selection
Default: RS-232 Data

Pin 1: DCD

3-5 close

Pin 9: RI

4-6 close

JP12

COM3 Data/Power Selection
Default: RS-232 Data

Pin 1: DCD

3-5 close

Pin 9: RI

4-6 close

JP13

COM4 Data/Power Selection
Default: RS-232 Data

Pin 1: DCD

3-5 close

Pin 9: RI

4-6 close

2.3 Jumper and Switch Settings

Jumper is a small component consisting of jumper clip and jumper pins. Install
jumper clip on 2 jumper pins to close. And remove jumper clip from 2 jumper pins
to open. The following illustration shows how to set up jumper.

Before applying power to GOT3156T-832, please make sure all of the jumpers and
switch are in factory default position. Below you can find a summary table and
onboard default settings.

10 Hardware and Installation

GOT3156T-832 User’s Manual

Back

Description

Jumper Setting

RS-232 (Default)

JP7 JP8

JP9

RS-422

JP8

JP7

JP9

RS-485

JP8

JP7

JP9

Description

JP10~JP13

Pin1: DCD
Pin9: RI
(Default)

Pin1: +5V
Pin9: +12V

Pin1: +5V
Pin9: RI

Pin1: DCD
Pin9: +12V

2.3.1 COM1 Configuration

The COM1~4 are a standard DB-9 connector. Those connectors are equipped with
The GOT3156T-832 has four serial ports. COM1 is RS-232/422/485, while COM2 to COM4 are
RS-232. The following table shows you set COM1 port mode:

2.3.2 COM port Power Configuration

All of the serial ports can output data or power through jumper setting.
The following table shows you how to do that.

Note: Each port +5V Maximum: 2A, +12V Maximum: 1A.

Hardware and Installation 11

GOT3156T-832 User’s Manual

Back

Function

Setting

Enable auto power on

1-2 close

Disable auto power on (Default)

2-3 close

Function

Setting

Normal operation (Default)

1-2 close

Restore BIOS optimal defaults

2-3 close

Pin

RS-232

RS-422

RS-485

1

DCD

TX-

Data-

2

RXD

TX+

Data+

3

TXD

RX+

No use

4

DTR

RX-

No use

5

GND

GND

GND

6

DSR

No use

No use

7

RTS

No use

No use

8

CTS

No use

No use

9

RI

No use

No use

2.3.3 Auto Power On (JP4)

If JP4 is enabled for power input, the system will be automatically power on
without pressing soft power button. If JP4 is disabled for power input, it is
necessary to manually press soft power button to power on the system.

2.3.4 Restore BIOS Optimal Defaults (JP6)

Put jumper clip to pin 2-3 for a few seconds then move it back to pin 1-2. Doing
this procedure can restore BIOS optimal defaults.

2.4 COM port Connector

The pin assignment of RS-232/RS-422/RS-485 is listed on the following table. If
you need COM1 port to support RS-422 or RS-485 mode, please refer to Jumper
Settings

12 Hardware and Installation

GOT3156T-832 User’s Manual

Back

Pin

100Base-T

1000Base-T

1

TX+

BI-DA+

2

TX-

BI-DA-

3

RX+

BI-DB+

4

NC

BI-DB-

5

NC

BI-DC+

6

RX-

BI-DC-

7

NC

BI-DD+

8

NC

BI-DD-

1234567

8

RJ-45

2.5 Ethernet

The GOT3156T-832 is equipped with a high performance Plug and Play Ethernet
interface, full compliant with IEEE 802.3 standard, and can be connected with a
RJ-45 LAN connector.

Please refer to detailed pin assignment list below:

2.6 Mountings: Panel / Wall / VESA

There are 4 application options for the GOT3156T-832, Panel/Wall/Desktop/VESA
mountings.

2.6.1 VESA-ARM/Wall-Mount

The GOT3156T-832 provides two ways for VESA mount: 100x100 mm. Screw four
screws to fix the kit (option) in the back chassis.

Wall mount:

Hardware and Installation 13

GOT3156T-832 User’s Manual

Back

VESA mount:

14 Hardware and Installation

GOT3156T-832 User’s Manual

Back

2.6.2 Panel-mount Kit Assembly

The GOT3156T-832 is designed for panel mount application. To mount the
GOT3156T-832, the standard set of mounting kit (included in the system
packaging) is needed.

2.7 HDD Installation

The GOT3156T-832 provides a convenient Hard Disk Drive (HDD) bracket for
users to install 2.5” SATA HDD. Please follow the steps:

Step 1 Refer section 2.1 to open the back cover.
Step 2 Unscrew 4 screws to take off the HDD bracket.

Hardware and Installation 15

GOT3156T-832 User’s Manual

Back

Step 3 Fix the HDD on bracket by 4 screws.

16 Hardware and Installation

GOT3156T-832 User’s Manual

Back

Step 4 Fix the HDD bracket into the system, and plug the data and power cable to

HDD. Installation completes.

2.8 DRAM Installation

The GOT3156T-832 provides one 204-pin DDR3 SODIMM socket that support
system memory up to 2GB. Please follow steps below to install the memory
modules:

Step 1 Refer to section 2.1 to open the back cover and find out DIMM socket on main

board (SBC87832).

Hardware and Installation 17

GOT3156T-832 User’s Manual

Back

Step 2 Stick the thermal pad on the back cover and rip the red mylar from it.

Step 3 Insert the DRAM to the DIMM socket, and then push it down firmly until it is

clipped by the socket.

18 Hardware and Installation

Back

Step 4 Installation completes.

GOT3156T-832 User’s Manual

2.9 Wireless LAN Card Installation

The GOT3156T-832 provides one Mini card slot for user to install one wireless
LAN card. When installing the wireless LAN card, refer to the following
instructions and illustration:

Step 1 Refer to section 2.1 to open the back cover and find out mini-card slot on

main board.

Hardware and Installation 19

GOT3156T-832 User’s Manual

Back

Step 2 Insert the wireless LAN card to the slot. Push it down firmly until it is clipped

by the slot.



Step 3 Find the Antenna cable and connect it wireless LAN card.



Step 4 Remove the antenna plug from the top of back cover, and then install the

antenna on the antenna connector

20 Hardware and Installation

GOT3156T-832 User’s Manual

Back

2.10 Power Input

GOT3156T-832 equips with a phoenix type power connector. It adopts 10VDC to
30VDC. Please follow the signs on power connector to connect DC power source.

+: Power positive G: Safety ground －:Power negative

Note: The safety ground must be connected to ensure the unit working appropriately.

Hardware and Installation 21

GOT3156T-832 User’s Manual

Back

This page is intentionally left blank.

22 Hardware and Installation

GOT3156T-832 User’s Manual

Back

Hot Keys

Description

 Left/Right

The Left and Right <Arrow> keys allow you to select a setup screen.

 Up/Down

The Up and Down <Arrow> keys allow you to select a setup screen or
sub-screen.

+ Plus/Minus

The Plus and Minus <Arrow> keys allow you to change the field value of a
particular setup item.

Tab

The <Tab> key allows you to select setup fields.

F1

The <F1> key allows you to display the general help screen.

F2

The <F2> key allows you to load previous values.

F3

The <F3> key allows you to load optimized defaults.

F4

The <F4> key allows you to save any changes you have made and exit
setup. Press the <F4> key to save your changes.

Esc

The <Esc> key allows you to discard any changes you have made and exit
the setup. Press the <Esc> key to exit the setup without saving your
changes.

Enter

The <Enter> key allows you to display or change the setup option listed for a
particular setup item. The <Enter> key can also allow you to display the
setup sub- screens.

Chapter 3

AMI BIOS Setup Utility

This chapter provides users with detailed description how to set up basic system
configuration through the AMIBIOS BIOS setup utility.

3.1 Starting

To enter the setup screens, follow the steps below:
Turn on the computer and press the <Del> key immediately.
After you press the <Delete> key, the main BIOS setup menu displays. You can access the
other setup screens from the main BIOS setup menu, such as the Chipset and Power
menus.

3.2 Navigation Keys

The BIOS setup/utility uses a key-based navigation system called hot keys. Most of the
BIOS setup utility hot keys can be used at any time during the setup navigation process.
These keys include <F1>, <F2>, <Enter>, <ESC>, <Arrow> keys, and so on.

Note: Some of the navigation keys differ from one screen to another.

AMI BIOS Setup Utility 23

GOT3156T-832 User’s Manual

Back

3.3 Main Menu

When you first enter the Setup Utility, you will enter the Main setup screen. You can always
return to the Main setup screen by selecting the Main tab. There are two Main Setup
options. They are described in this section. The Main BIOS Setup screen is shown below

 System Date/Time

Use this option to change the system time and date. Highlight System Time or System
Date using the <Arrow> keys. Enter new values through the keyboard. Press the <Tab>
key or the <Arrow> keys to move between fields. The date must be entered in MM/DD/YY
format. The time is entered in HH:MM:SS format.

24 AMI BIOS Setup Utility

GOT3156T-832 User’s Manual

Back

3.4 Advanced Menu

 Launch Storage OpROM

This item can enable or disable boot option for legacy mass storage devices with option
ROM.

The Advanced menu also allows users to set configuration of the CPU and other system
devices. You can select any of the items in the left frame of the screen to go to the sub menus:

► ACPI Settings
► CPU Configuration
► IDE Configuration
► USB Configuration
► NCT6627UD Superior IO Configuration
► NCT6627UD HW Monitor
► JMB36X ATA Controller Configuration

For items marked with “”, please press <Enter> for more options.

AMI BIOS Setup Utility 25

GOT3156T-832 User’s Manual

Back

 ACPI Settings

You can use this screen to select options for the ACPI Configuration, and change the value
of the selected option. A description of the selected item appears on the right side of the
screen.

ACPI Sleep State

Use this item to select the highest ACPI sleep state the system will enter.

26 AMI BIOS Setup Utility

GOT3156T-832 User’s Manual

Back

 CPU Configuration

This screen shows the CPU Configuration, and you can change the value of the selected
option.

Hyper-Threading

Use this item to enable or disable Hyper-Threading Technology, which makes a single
physical processor perform multi-tasking function as two logical ones.

Execute Disable Bit

XD can prevent certain classes of malicious buffer overflow attacks when combined with a
supporting OS (Windows Server 2003 SP1, Windows XP SP2, SuSE Linux 9.2, RedHat
Enterprise 3 Update 3).

AMI BIOS Setup Utility 27

GOT3156T-832 User’s Manual

Back

 IDE Configuration

SATA Controller(s)

The optional settings are: [Disabled]; [Enabled].

Configure SATA as

The optional settings are: [IDE]; [AHCI].

28 AMI BIOS Setup Utility

GOT3156T-832 User’s Manual

Back

 USB Configuration

You can use this screen to select options for the USB Configuration, and change the value
of the selected option. A description of the selected item appears on the right side of the
screen.

Legacy USB Support

The optional settings are: [Auto]; [Disabled]; [Enabled].

AMI BIOS Setup Utility 29

GOT3156T-832 User’s Manual

Back

 NCT6627UD Super IO Configuration

You can use this screen to select options for the Super IO Configuration, and change the
value of the selected option. A description of the selected item appears on the right side of
the screen

Serial Port Configuration

Use this item to set parameters of serial port 0~1

30 AMI BIOS Setup Utility

GOT3156T-832 User’s Manual

Back

 PC Health Status

This screen shows the Hardware Health Configuration, and a description of the selected
item appears on the right side of the screen.

AMI BIOS Setup Utility 31

GOT3156T-832 User’s Manual

Back

3.5 Chipset Menu

The Chipset menu allows users to change the advanced chipset settings. You can select
any of the items in the left frame of the screen to go to the sub menus:

► Host Bridge

Host Bridge For items marked with “”, please press <Enter> for more options.

► South Bridge

South Bridge For items marked with “”, please press <Enter> for more options.

32 AMI BIOS Setup Utility

GOT3156T-832 User’s Manual

Back

 Memory Information

This item is for memory frequency and timing settings. Press <Enter> to go to the sub
menu.

AMI BIOS Setup Utility 33

GOT3156T-832 User’s Manual

Back

3.6 Boot Menu

The Boot menu allows users to change boot options of the system.

 Boot Settings Configuration

Setup Prompt Timeout

Use this item to set number of seconds to wait for setup activation key.

Bootup NumLock State

Use this item to select the power-on state for the NumLock.. The optional settings are: [On];
[Off].

GateA20 Active

If Upon Request is selected, GA20 can be disabled using BIOS services. If Always is selected,
disabling G20 is not allowed; this option is useful when any RT code is executed above 1MB.

Option ROM Messages

Set display mode for option ROM. Configuration options are Force BIOS and Keep Current.

Interrupt 19 Capture

If this item is enabled, this function makes the option ROM to trap Interrupt 19.

Boot Option Priorities

These are settings for boot priority. Specify the boot device priority sequence from the
available devices.

34 AMI BIOS Setup Utility

GOT3156T-832 User’s Manual

Back

3.7 Security Menu

The Security menu allows users to change the security settings for the system.

Administrator Password

This item indicates whether an administrator password has been set. If the password has been
installed, Installed displays. If not, Not Installed displays.

User Password

This item indicates whether an user password has been set. If the password has been installed,
Installed displays. If not, Not Installed displays.

AMI BIOS Setup Utility 35

GOT3156T-832 User’s Manual

Back

3.8 Save & Exit Menu

The Save & Exit menu allows users to load your system configuration with optimal or
fail-safe default values.

Save Changes and Exit

When you have completed the system configuration changes, select this option to leave Setup
and reboot the computer so the new system configuration parameters can take effect. Select
Save Changes and Exit from the Exit menu and press <Enter>. Select Ok to save changes
and exit.

Discard Changes and Exit

Select this option to quit Setup without making any permanent changes to the system
configuration. Select Discard Changes and Exit from the Exit menu and press <Enter>. Select
Ok to discard changes and exit.

Save Changes and Reset

When you have completed the system configuration changes, select this option to leave Setup
and reboot the computer so the new system configuration parameters can take effect. Select
Save Changes and Reset from the Save & Exit menu and press <Enter>. Select Yes to save
changes and reset.

Discard Changes and Reset

Select this option to quit Setup without making any permanent changes to the system
configuration and reboot the computer. Select Discard Changes and Reset from the Save &
Exit menu and press <Enter>. Select Yes to discard changes and reset.

Save Changes

When you have completed the system configuration changes, select this option to save
changes. Select Save Changes from the Save & Exit menu and press <Enter>. Select yes to
save changes.

36 AMI BIOS Setup Utility

GOT3156T-832 User’s Manual

Back

Discard Changes

Select this option to quit Setup without making any permanent changes to the system
configuration. Select Discard Changes from the Save & Exit menu and press <Enter>. Select
Yes to discard changes.

Restore Defaults

It automatically sets all Setup options to a complete set of default settings when you select this
option. Select Restore Defaults from the Save & Exit menu and press <Enter>.

Save as User Defaults

Select this option to save system configuration changes done so far as User Defaults. Select
Save as User Defaults from the Save & Exit menu and press <Enter>.

Restore User Defaults

It automatically sets all Setup options to a complete set of User Defaults when you select this
option. Select Restore User Defaults from the Save & Exit menu and press <Enter>.

Boot Override

Select a drive to immediately boot that device regardless of the current boot order.

Note: If you want to use a CF card that capacity is less than 2GB (such as 1GB, 512MB),

we recommend you may switch “AHCI mode” to “IDE mode” with "Configure SATA as"
of the BIOS setting.
And please make sure your Operating System (Ex: Windows Embedded) is installed
with “IDE” driver.

AMI BIOS Setup Utility 37

GOT3156T-832 User’s Manual

Back

This page is intentionally left blank.

38 AMI BIOS Setup Utility

GOT3156T-832 User’s Manual

Back

Touch Screen

5-wire Analog Resistive type

Touch Screen Controller

PenMount 6000 USB Touch Screen Controller IC

Communications

USB interface

Resolution

10bit AD (1024 x 1024)

Power Input

5V

Power Consumption

Active: 24.6mA / Idle Mode: 13.4mA

Chapter 4

Drivers Installation

4.1 System

GOT3156T-832 supports Windows 7 32-bit and WES 7. To facilitate the installation of
system driver, please carefully read the instructions in this chapter before start installing.

Step 1 Insert Driver CD and select the “\Driver”.

Step 2 Select all files and follow the installing procedure.

4.2 Touch Screen

The GOT3156T-832 uses the 5-wire analog resistive touch panel. There are the
specification and driver installation which are listed below.

 Specification

Drivers Installation 39

GOT3156T-832 User’s Manual

Back

 Driver Installation- Windows 7

The GOT3156T-832 provides a touch screen driver that users can install it under the
operating system Windows 7. To facilitate installation of the touch screen driver, you should
read the instructions in this chapter carefully before you attempt installation.

Step 1 Insert Driver CD and follow the path to select the “\Driver\Step 5 - Touch”.

Step 2 Follow the installing procedure and press OK.
Step 3 Click Start menu and select “PenMount Utilities”; and then, a “PenMount

Control Panel” pops out.

Step 4 Select the “Standard Calibrate” tab.

40 Drivers Installation

Back

Step 5 Calibration:

To adjust the display with touch panel, click “Calibration” and follow the calibrate
point to do calibration; there are five points on screen for calibration.

Step 6 Press OK.

GOT3156T-832 User’s Manual

Note: For the better system performance, please close the Windows AERO or change to

Windows Basic mode.

4.3 Embedded O.S.

The GOT3156T-832 provides the Windows 7 Embedded. The O.S. is supported devices
which are listed below.

 WES 7

Here are supported onboard devices:

 Onboard Multi I/O
 SATA HDD
 USB
 CRT/LCD display
 10/100/1000 base-T Ethernet
 Compact Flash
 Onboard Audio
 Touch Screen

Drivers Installation 41

GOT3156T-832 User’s Manual

Back

PenMount Touch screen

Before you can use and calibrate it, here is what you should do:

1. Set up Penmount touch device driver by executing C:\Penmount\ Windows
2000-XP V5.0\setup.exe. When the installation is finished, an icon “PM” appears on
the Taskbar.

2. Calibrate Penmount touch by clicking on the “PM” icon, and the go on the
calibration.

3. Restart the computer.

Please be informed if you use the Windows XP OS, the graphic driver supported by Intel is EMGD, there
are three known issues as below:

Note: The Intel EMGD package does not include Intel HD audio driver, there will be an

unknown device under device manager.

Note: 3D Graphic render function is not supported.

Note: User cannot disable LVDS and VGA output at the same time.

42 Drivers Installation