This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third
party’s rights, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make any
commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written permission of Axiomtek Co., Ltd.
CAUTION
If you replace wrong batteries, it causes the danger of explosion. It is recommended by the
manufacturer that you follow the manufacturer’s instructions to only replace the same or
equivalent type of battery, and dispose of used ones.
Copyright 2015 Axiomtek Co., Ltd.
All Rights Reserved
March 2015, Version A1
Printed in Taiwan
ii
Page 3
Safety Precautions
Before getting started, read the following important cautions.
1. Be sure to ground yourself to prevent static charge when installing the internal
components. Use a grounding wrist strap and place all electronic components in any
static-shielded devices. Most electronic components are sensitive to static electrical
charge.
2. Disconnect the power cords from the GOT3126T-834 Series before making any
installation. Be sure both the system and the external devices are turned OFF. Sudden
surge of power could ruin sensitive components. Make sure the GOT3126T-834 Series is
properly grounded.
3. Do not open the system’s top cover. If opening the cover for maintenance is a must, only
a trained technician is allowed to do so. Integrated circuits on computer boards are
sensitive to static electricity. To avoid damaging chips from electrostatic discharge,
observe the following precautions:
Before handling a board or integrated circuit, touch an unpainted portion of the
system unit chassis for a few seconds. This will help to discharge any static
electricity on your body.
When handling boards and components, wear a wrist-grounding strap, available
from most electronic component stores.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
Windows® is a trademark of Microsoft Corporation.
IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation.
Intel® and Pentium® are trademarks of Intel Corporation.
AMI is trademark of American Megatrend Inc.
Other brand names and trademarks are the properties and registered brands of their
respective owners.
iii
Page 4
Table of Contents
Disclaimers ..................................................................................................... ii
Safety Precautions ........................................................................................ iii
This chapter contains general information and detailed specifications of the GOT3126T-834.
Chapter 1 includes the following sections:
General Description
Specification
Dimensions and outlines
I/O Outlets
Package List
1.1 General Description
The GOT3126T-834 adopts a 12.1-inch XGA TFT LCD with 600nits brightness and an Intel®
Processor E3827 (1M Cache, 1.75 GHz) to provide excellent computing performance and
thermal resistance. This fanless platform is especially designed for operating under
heavy-duty environment including steel refinery, oil pipe, machine maker operating systems
and many more. Having below abilities makes GOT 3126T-834 surely a most robust and
cost-effective solution.
Wide Operating Temperature Range
GOT3126T-834 features a technology of wide operating temperature range which allows it to
work between -20°C to +55°C. It incorporates compact ID and fanless cooling system with a
low power Intel® Processor E3827, making the platform a power-efficient solution.
Reliable and Stable Design
The GOT3126T-834 adopts a fanless cooling system, which makes it especially suitable for
vibration-heavy environments, best for the transportation and industrial machinery markets.
For high capacity storage requirement, GOT3126T-834 can work under 2.0G (10 ~ 500Hz,
random for CFast™) in operation mode with a patent of anti-vibration design. The patent
improves the system reliability and sustainability.
Introduction 1
Page 8
GOT3126T-834 User’s Manual
WLAN Antenna Supported (optional)
GOT3126T-834 has 2 PCI Express Mini Card slots for optional add-on such as wireless LAN
card for 802.11 a/b/g/n connections, 3G/GPRS application, and more. These slots also
provide 3 optional fixed rotational WLAN/3G antennas for wireless network connection.
More Features
GOT3126T-834 utilizes one 204-pin DDR3L SO-DIMM system memory max. up to 8GB, one
2.5” SATA HDD and one CFast™ or mSATA. It provides over-current protection-fuse and a
full set of I/O including RS-232/422/485, USB 2.0, USB 3.0, audio (line-out), and Gigabit
Ethernet. Additionally, this slim unit supports panel mount, wall mount (optional), VESA
mount and desktop stand (optional).
One 204-pin DDR3L SO-DIMM socket
Maximum memory up to 8GB
BIOS
America Megatrends BIOS
I/O System
Standard I/O
3 x RS-232/422/485 (adjust setting via BIOS)
2 x USB 2.0
2 x USB 3.0
1 x VGA output
(Duplicated display mode: max resolution is up to 1024 x 768, Extended display mode:
max resolution is up to 1920 x 1080)
Ethernet
2 x RJ45 for Giga Ethernet (Intel chipset)
Audio
1x Line-out
Expansion
1 x SATA 2
1 x Mini-card slot (w/SIM slot)
1 x Mini-card slot (supports mSATA, optional)
Storage
1 x 2.5” HDD/SSD bay
1 x CFast
Power connector
Phoenix power connector
TM
slot or mSATA
2 Introduction
Page 9
GOT3126T-834 User ’s Manual
System Specification
12.1” XGA (1024x768) LCD with LED backlight, 600nits(before touch)
5-wire resistive touch
Fanless Heat Dispensing Design
IP65 aluminum front bezel
3 keys OSD on front panel
Disk drive housing:
1 x 2.5” SATA drive
Net Weight
2.8 Kgs
Dimension (Main Body Size)
311.8 x 56.9 x 250.3 mm
Operation Temperature
-20℃ to 55℃
Relative Humidity
10% to 90% @ 40℃, Non-Condensing
System Power input
DC power input : 9~36VDC with phoenix power connector
NOTE: All specifications and images are subject to change without notice.
Introduction 3
Page 10
GOT3126T-834 User’s Manual
1.3 Dimensions and Outlines
The following diagrams show the dimensions and outlines of GOT3126T-834
Outline dimension: 311.8 x 56.9 x 250.3mm
4 Introduction
Page 11
Cut Out dimension: 301.8 x 240.2mm
GOT3126T-834 User ’s Manual
Product drawing
Introduction 5
Page 12
GOT3126T-834 User’s Manual
No
Function
No
Function
1
POWER SWITCH (ATX)
6
COM 1 (RS-232/422/485)
2
Power Input connector (phoenix type)
7
COM 2 (RS-232/422/485)
3
2 x USB 2.0
8
2 X Ethernet
4
VGA output
9
2 X USB 3.0
5
COM 3 (RS-232/422/485)
10
AUDIO (LINE-OUT)
1.4 I/O Outlets
Please refer to the following illustration for I/O locations of the GOT3126T-834.
Front panel 3 keys OSD:
I/O connectors
6 Introduction
Page 13
GOT3126T-834 User ’s Manual
1.5 Packing List
When you receive the GOT3126T-834, the bundled package should contain the following
items:
GOT3126T-834 unit x 1
Driver Disc x1
Phoenix connector x 1
Panel mount kit x 6
Screws for HDD x 4
SATA data cable x 1
SATA power cable x 1
If you can’t find the package or any items are missing, please contact Axiomtek distributors
immediately.
Introduction 7
Page 14
GOT3126T-834 User’s Manual
This page is intentionally left blank.
8 Introduction
Page 15
GOT3126T-834 User ’s Manual
Chapter 2
Hardware and Installation
The GOT3126T-834 provides rich I/O ports and flexible expansions for you to meet different
demand, for example CFast™ card. The chapter will show you how to install the hardware. It
includes:
Open Back Cover
CFast™ Card
Jumper and Switch Setting
Ethernet
Mounting Method
Hard disk
DRAM
Wireless LAN Card
Power Input
Hardware and Installation 9
Page 16
GOT3126T-834 User’s Manual
2.1 Open back cover
This section tells users how to open back cover. Please follow the steps below.
Step 1 Unscrew 10 screws on the back cover. Please refer the photo below.
Step 2 Remove the back cover.
10 Hardware and Installation
Page 17
GOT3126T-834 User ’s Manual
2.2 CFast card Installation
The GOT3126T-834 provides one CFast slot for users to install CFast™ card. Please refer to
the following instructions for installation:
Step 1 Unscrew a screw on the cover of CFast™ card slot on left side.
Step 2 Find the CFast card.
Step 3 Insert it into the socket.
Step 4 Close the cover of CFast™ card slot and fix it. Installation completes.
Hardware and Installation 11
Page 18
GOT3126T-834 User’s Manual
2.3 Jumper and Switch Setting
Jumpers and Connectors Layout
Component Side
12 Hardware and Installation
Page 19
GOT3126T-834 User ’s Manual
Solder Side
Hardware and Installation 13
Page 20
GOT3126T-834 User’s Manual
Jumper
★ Default Setting
Jumper Setting
JP1
★ Panel backlight control PWM mode
Panel backlight control DC mode
Short 1-2
Short 3-4
JP2
Touch Controller 4,8 WIRE
★ Touch Controller 5 WIRE
Short 1-2
Short 2-3
JP4
★ LVDS Panel Power : 3.3V
LVDS Panel Power : 5V
Short 1-2
Short 2-3
JP5
Touch OFF
★ Touch ON
Short 1-2
Short 2-3
JP6
★ PCIe device
mSATA device
Short 1-2
Short 2-3
JP7
AT mode
★ ATX mode
Short 1-2
Short 2-3
JP8
★ Normal
Clear CMOS
Short 1-2
Short 2-3
JP11
COM3_5VSB
★ COM3_5V
Short 1-2
Short 2-3
JP12
★ COM1 normal mode
COM1 pin1 with power :+5V
COM1 pin9 with power :+12V
Short 3-5,4-6
Short 1-3,4-6
Short 3-5,2-4
JP13
★ COM2 normal mode
COM2 pin1 with power :+5V
COM2 pin9 with power :+12V
Short 3-5,4-6
Short 1-3,4-6
Short 3-5,2-4
JP14
★ COM3 normal mode
COM3 pin1 with power :+5V
COM3 pin9 with power :+12V
Short 3-5,4-6
Short 1-3,4-6
Short 3-5,2-4
Jumper Settings
Jumper is a small component consisting of jumper clip and jumper pins. Install jumper clip on 2
jumper pins to close. And remove jumper clip from 2 jumper pins to open. The following
illustration shows how to set up jumper.
Making the proper jumper settings configure the SBC87834 to match the needs of your
application. The following table shows the default jumper settings for the onboard devices.
14 Hardware and Installation
Page 21
GOT3126T-834 User ’s Manual
Function
Setting
PCIe device(default)
1-2 close
mSATA device
2-3 close
Function
Setting
Normal operation (Default)
1-2 close
Restore BIOS optimal defaults
2-3 close
PCIe device & mSATA device selection (JP6)
The default setting of JP6 is for PCIe mini-card. If you want to install mSATA card on your
system, please remember to set this jumper to “2-3 close”.
Restore BIOS Optimal Defaults (JP8)
Put jumper clip to pin 2-3 for a few seconds then move it back to pin 1-2. Doing this procedure
can restore BIOS optimal defaults.
Hardware and Installation 15
Page 22
GOT3126T-834 User’s Manual
Connectors
Label
LVDS connector
CN1
LVDS inverter connector
CN2
TOUCH connector
CN3
HDD power connector
CN4
Full size min-PCIe connector
CN5
FRONT PANEL pin header
CN6
SIM card connector
CN7
Full size min-PCIe connector
CN8
DC IN connector
CN9
Digital I/O pin header
CN10
Speaker Out & MIC IN connector
CN11
VGA connector
CN12
Audio connector
CN13
USB CONNECTOR (reserved)
CN14/CN20
Audio Lin In connector
CN15
Power lamp connector
CN16
Power button connector
CN17
Touch function enable/disable & LED indicator connector
CN18
Panel control Keypad connector
CN19
CPU FAN
FAN1
System FAN
FAN2
USB2.0 box header
USB1
USB3.0 connector
USB2
Display Port connector
DP1
SATA connector
SATA1
RJ45 LAN connector
LAN1, LAN2
Serial Port connector
COM1,COM2
Serial Port box header
COM3,COM4
CFast connector
SCF1
Connectors
The connectors allow the CPU Board to connect with other parts of the system. Ensure that all
connectors are in place and firmly attached. The following table lists the function of each
connector on the SBC87834.
16 Hardware and Installation
Page 23
Pin
Description
Pin
Description
1
VCC
21
GND
2
VCC
22
GND
3
VCC
23
LVDSA_DATAN0
4
VCC
24
LVDSB_DATAN2
5
VCC
25
LVDSA_DATAP0
6
VCC
26
LVDSB_DATAP2
7
DDC DATA
27
GND
8
DDC CLOCK
28
GND
9
GND
29
LVDSA_DATAN1
10
GND
30
LVDSA_DATAN3
11
LVDSB_DATAN3
31
LVDSA_DATAP1
12
LVDSB_DATAN0
32
LVDSA_DATAP3
13
LVDSB_DATAP3
33
GND
14
LVDSB_DATAP0
34
GND
15
GND
35
LVDSA_DATAN2
16
GND
36
LVDSA_CLKN
17
LVDSB_CLKN
37
LVDSA_DATAP2
18
LVDSB_DATAN1
38
LVDSA_CLKP
19
LVDSB_CLKP
39
GND
20
LVDSB_DATAP1
40
GND
LVDS connector: CN1
CN1 Pin Assignment
GOT3126T-834 User ’s Manual
Hardware and Installation 17
Page 24
GOT3126T-834 User’s Manual
Pin
Description
Pin
Description
1
GND
5
Inverter ON-OFF
2
GND
6
+12V
3
GND
7
+12V
4
Backlight control
8
+12V
Pin
Description
1
X+ 2 X-
3
Y+
4
Sense
5
X+
6
X- 7 Y+ 8 Y- 9 GND
Pin
Description
1
+12V
2
GND
3
GND
4
+5V
LVDS inverter connector: CN2
CN2 Pin Assignment
TOUCH connector: CN3
CN3 Pin Assignment
HDD power connector: CN4
CN9 Pin Assignment
18 Hardware and Installation
Page 25
Pin
Description
Pin
Description
1
UIM PWR
5
GND
2
UIM RST
6
UIM VPP
3
UIM CLK
7
UIM DATA
4
NC
8
NC
Pin
Description
1
DCIN (9V -36V)
2
DCIN (9V -36V)
3
GND
4
GND
Pin
Description
Pin
Description
1
+ 5V
2
Beep 3 GND
4
BUZZER
5
GND
6
Beep
7
NC
8
+5V
9
GND
10
PWBTN
11
GND
12
RESET
13
SATA LED
14
+3.3V
FRONT PANEL pin header: CN6
CN6 Pin Assignment
SIM card connector: CN7
CN7 Pin Assignment
GOT3126T-834 User ’s Manual
Power connector: CN9
CN9 Pin Assignment
Hardware and Installation 19
Page 26
GOT3126T-834 User’s Manual
Pin
Description
Pin
Description
1
SPKOUT_L-
2
SPKOUT_L +
3
SPKOUT_R-
4
SPKOUT_R +
5
MIC IN 6 GND
Pin
Description
Pin
Description
1
GND 6 GND
2
GPIO0
7
GPIO1
3
GPIO2
8
GPIO3
4
GPIO4
9
GPIO5
5
GPIO6
10
GPIO7
11
GPIO8
12
GPIO9
13
GPIO10
14
GPIO11
15
GPIO12
16
GPIO13
17
GPIO14
18
GPIO15
19
GND
20
GND
Pin
Signal
Pin
Signal
1
Red 2 GND
3
Green 4 N.C.
5
Blue 6 N.C.
7
VCC
8
DDC DATA
9
GND
10
N.C.
11
GND .
12
Horizontal Sync
13
GND
14
Vertical Sync
15
DCC CLK
16
N.C.
Digital I/O pin header: CN10
CN10 Pin Assignment
Speaker-out & MIC-in connector: CN11
CN11 Pin Assignment
VGA Cable Connector: CN12
CN12 Pin Assignment
20 Hardware and Installation
Page 27
Pin
Description
1
LINE IN L
2
GND
3
LIN IN R
Pin
Description
Pin
Description
1
Power (+5V)
2
GND
Pin
Description
Pin
Description
1
Power Button
2
GND
Pin
Description
1
ON/OFF button
2
GND
3
LED
Pin
Description
1
VCC
2
D-
3
D+
4
GND
5
GND
USB CONNECTOR (reserved): CN14/CN20
CN14/CN20 Pin Assignment
Audio Lin In connector: CN15
CN15 Pin Assignment
GOT3126T-834 User ’s Manual
Power lamp connector: CN16
CN16 Pin Assignment
Power button connector: CN17
CN17 Pin Assignment
Touch function enable/disable & LED indicator connector: CN18
CN18 Pin Assignment
Hardware and Installation 21
Page 28
GOT3126T-834 User’s Manual
Pin
Description
1
GND
2
Panel ON/OFF
3
Normal indicate LED
4
POWER LED
5
Blacklight down
6
Blacklight up
Pin
Description
Pin
Description
1
+5V
2
+5V 3 USB-
4
USB- 5 USB+
6
USB+ 7 GND
8
GND
9
GND
10
GND
Pin
Description
Pin
Description
1
DCD
2
DSR
3
RX
4
RTS
5
TX
6
CTS 7 DTR
8
RI
9
GND
10
NC
Panel control Keypad connector: CN19
CN19 Pin Assignment
USB box header: USB1
USB1 Pin Assignment
Serial Port box header: COM3
COM3 Pin Assignment
22 Hardware and Installation
Page 29
GOT3126T-834 User ’s Manual
Pin
RS-232
RS-422
RS-485
COM port
1
DCD, Data Carrier Detect
TX-
Data-
2
RXD, Receive Data
TX+
Data+
3
TXD, Transmit Data
RX+
No use
4
DTR, Data Terminal Ready
RX-
No use
5
GND, Ground
No use
No use
6
DSR, Data Set Ready
No use
No use
7
RTS, Request To Send
No use
No use
8
CTS, Clear To Send
No use
No use
9
RI, Ring Indicator
No use
No use
Pin
Signal
1
2345678
RJ-45
1
TX+ (Data transmission positive
2
TX- (Data transmission negative)
3
Rx+(Data reception positive)
4
RJ45 termination
5
RJ45 termination
6
Rx- (Data reception negative)
7
RJ45 termination
8
RJ45 termination
The system has four serial ports. They are RS-232/422/485 ports. Please
refer to below table for the detail of pin assignment.
2.4 Ethernet
The GOT3126T-834 is equipped with a high performance Plug and Play Ethernet interface, full
compliant with IEEE 802.3 standard, and can be connected with a RJ-45 LAN connector.
Please refer to detailed pin assignment list below:
Hardware and Installation 23
Page 30
GOT3126T-834 User’s Manual
2.5 Mountings: Panel / Wall / Desktop / VESA
There are 4 application options for the GOT3126T-834, Panel/Wall/Desktop/VESA mountings.
VESA-ARM/Wall-Mount
VESA mount: 100x100 mm. Screw four screws to fix VESA arm or other VESA fixture.
Wall mount: This is an optional wall kit. Screw it on the rear of chassis to support
wall mount.
24 Hardware and Installation
Page 31
GOT3126T-834 User ’s Manual
Panel-mount Kit Assembly
The GOT3126T-834 is designed for panel mount application. To mount the GOT3126T-834,
the standard set of mounting kit (included in the system packaging) is needed.
Hardware and Installation 25
Page 32
GOT3126T-834 User’s Manual
2.6 HDD Installation
The GOT3126T-834 provides a convenient Hard Disk Drive (HDD) bracket for users to install
2.5” SATA HDD. Please follow the steps:
Step 1 Refer section 2.1 to open the back cover.
Step 2 Unscrew 4 screws to take off the HDD bracket.
Step 3 Fix the HDD on bracket by 4 screws.
26 Hardware and Installation
Page 33
GOT3126T-834 User ’s Manual
Step 4 Fix the HDD bracket into the system, and plug the data and power cable to HDD
& SBC87834 mother board. Installation completed.
Hardware and Installation 27
Page 34
GOT3126T-834 User’s Manual
2.7 DRAM Installation
The GOT3126T-834 provides one 204-pin DDR3L SODIMM socket that supports system
memory up to 8GB. Please follow steps below to install the memory modules:
Step 1 Refer to section 2.2 to open the back cover.
Step 2 Insert the DRAM to the DIMM socket, and then push it down firmly until it is
clipped by the socket.
Installation completed
28 Hardware and Installation
Page 35
GOT3126T-834 User ’s Manual
Function
Setting
PCIe device(default)
1-2 close
mSATA device
2-3 close
2.8 mSATA Card Installation
The GOT3126T-834 provides one Mini card slot for user to install one mSATA card. When
installing it, please refer to the following instructions and illustration:
Step 1 Refer to section 2.1 to open the back cover and find out mini-card slot (CN8) on
mainboard.
Step 2 Insert the wireless LAN card to the slot. Push it down firmly and screw it.
Hardware installation completed.
The default setting of JP6 is for PCIe mini-card. If you want to install mSATA card on your
system, please remember to set this jumper to 2-3 close.
Hardware and Installation 29
Page 36
GOT3126T-834 User’s Manual
2.9 Wireless LAN Card Installation
The GOT3126T-834 provides one Mini card slot for user to install one wireless LAN card.
When installing the wireless LAN card, refer to the following instructions and illustration:
Step 1 Refer to section 2.1 to open the back cover and find out mini-card slot on
mainboard.
Step 2 Insert the wireless LAN card to the slot. Push it down firmly until it is clipped
by the slot.
30 Hardware and Installation
Page 37
GOT3126T-834 User ’s Manual
Step 3 Find the Antenna cable and connect it on wireless LAN card.
Step 4 Remove the antenna plug from the top of back cover, then Install the antenna
on the antenna connector.
NOTE: Please have the extended bracket when using half-size mini card.
Hardware and Installation 31
Page 38
GOT3126T-834 User’s Manual
2.10 Power Input
GOT3126T-834 equips with a phoenix type power connector. It adopts 9VDC to 36VDC.
Please follow the signs on power connector to connect DC power source.
+: Power positive G: Safety ground -: Power negative
NOTE: The safety ground must be connected to ensure the unit working appropriately.
32 Hardware and Installation
Page 39
GOT3126T-834 User ’s Manual
Left/Right
The Left and Right <Arrow> keys allow you to select a setup screen.
Up/Down
The Up and Down <Arrow> keys allow you to select a setup screen or sub-screen.
+ Plus/Minus
The Plus and Minus <Arrow> keys allow you to change the field value of a particular
setup item.
Tab
The <Tab> key allows you to select setup fields.
F1
The <F1> key allows you to display the General Help screen.
F2
The <F2> key allows you to load previous value
F3
The <F3> key allows you to Load Optimized Defaults.
F4
The <F4> key allows you to save any changes you have made and exit Setup.
Press the <F4> key to save your changes.
Esc
The <Esc> key allows you to discard any changes you have made and exit the
Setup. Press the
<Esc> key to exit the setup without saving your changes.
Enter
The <Enter> key allows you to display or change the setup option listed for a
particular setup item. The <Enter> key can also allow you to display the setup subscreens.
Chapter 3
AMI BIOS Setup Utility
This chapter provides users with detailed description how to set up basic system configuration
through the AMIBIOS8 BIOS setup utility.
3.1 Navigation Keys
The BIOS setup/utility uses a key-based navigation system called hot keys. Most of the BIOS
setup utility hot keys can be used at any time during the setup navigation process.
These keys include <F1>, <F2>, <F3>, <F4>, <Enter>, <ESC>, <Arrow> keys, and so on.
NOTE: Some of navigation keys differ from one screen to another.
AMI BIOS Setup Utility 33
Page 40
GOT3126T-834 User’s Manual
3.2 Main Menu
System Time/Date
Use this option to change the system time and date. Highlight System Time or System Date
using the <Arrow> keys. Enter new values through the keyboard. Press the <Tab> key or the
<Arrow> keys to move between fields. The date must be entered in MM/DD/YY format. The
time is entered in HH:MM:SS format.
34 AMI BIOS Setup Utility
Page 41
3.3 Advanced Menu
GOT3126T-834 User ’s Manual
The Advanced menu allows users to set configuration of the CPU and other system devices.
You can select any of the items in the left frame of the screen to go to the sub menus:
ACPI Settings
NCT6106D Super IO Configuration
NCT6106D H/W Monitor
CPU Configuration
IDE Configuration
LPSS & SCC Configuration
Security Configuration
For items marked with “”, please press <Enter> for more options.’
AMI BIOS Setup Utility 35
Page 42
GOT3126T-834 User’s Manual
ACPI Settings
You can use this screen to select options for the ACPI Configuration, and change the value of
the selected option. A description of the selected item appears on the right side of the screen.
ACPI Sleep State
Allow you to select the Advanced Configuration and Power Interface (ACPI) state to be used
for system suspend. Here are the options for your selection, Suspend disable and S3
(Suspend to RAM).
36 AMI BIOS Setup Utility
Page 43
GOT3126T-834 User ’s Manual
NCT6106D Super IO Configuration
Use this screen to select options for the Super IO Configuration, and change the value of the
selected option
Serial Port 1-3 configuration
Serial port:
This option used to enable or disable the serial port.
Device Setting:
This item specifies the base I/O port address and Interrupt Request address of serial port.
The port 0 Optimal setting is 3F8/IRQ4.
The port 1 Optimal setting is 2F8/IRQ3.
The port 2 Optimal setting is 3E8/IRQ7
AMI BIOS Setup Utility 37
Page 44
GOT3126T-834 User’s Manual
Serial type:
This option used to select RS232/422/485 function.
38 AMI BIOS Setup Utility
Page 45
NCT6106D H/W Monitor
This screen shows the Hardware Health Configuration.
GOT3126T-834 User ’s Manual
AMI BIOS Setup Utility 39
Page 46
GOT3126T-834 User’s Manual
CPU Configuration
This screen shows the CPU Configuration and Intel virtualization technology enable/disable
selected
40 AMI BIOS Setup Utility
Page 47
GOT3126T-834 User ’s Manual
IDE Configuration
You can use this screen to select options for the SATA Configuration, and change the value of
the selected option.
SATA Mode
Use this item to choose the SATA operation mode. Here are the options for your selection, IDE
Mode, AHCI Mode.
AMI BIOS Setup Utility 41
Page 48
GOT3126T-834 User’s Manual
LPSS & SCC Configuration
You can select any of the items in the frame of the screen to change the OS, the default setting
is Win 7.
Please be informed to select the Windows 8.x when installing Win 8 or Win 8.1.
42 AMI BIOS Setup Utility
Page 49
Security Configuration - Intel TXE Configuration
The Advanced menu allows users to update the TXE firmware.
GOT3126T-834 User ’s Manual
AMI BIOS Setup Utility 43
Page 50
GOT3126T-834 User’s Manual
3.4 Chipset Menu
The Chipset menu allows users to change the advanced chipset settings.
44 AMI BIOS Setup Utility
Page 51
North Bridge
This screen shows the North Bridge memory information.
GOT3126T-834 User ’s Manual
South Bridge
AMI BIOS Setup Utility 45
Page 52
GOT3126T-834 User’s Manual
USB Configuration
You can use this screen to select options for the USB Configuration,
If USB3.0 function used, XHCI Mode must enable and EHCI must disable.
**XHCI default is Auto.
46 AMI BIOS Setup Utility
Page 53
3.5 Security
GOT3126T-834 User ’s Manual
AMI BIOS Setup Utility 47
Page 54
GOT3126T-834 User’s Manual
3.6 Boot Menu
The Boot menu allows users to change boot options of the system. You can select any of the
items in the left frame of the screen to go to the sub menus:
Setup Prompt Timeout
Set the Timeout for wait press key to enter Setup Menu.
Bootup NumLock State
Use this item to select the power-on state for the NumLock. The default setting is on.
Quiet Boot
Use this item to enable or disable the Quite Boot state. The default setting is disable.
Legacy Pxe OPROM
Use this item to enable or disable the Preboot Execution Environment. The default setting is
disable.
Boot Option Priorities
Specifies the overall boot order from the available devices.
48 AMI BIOS Setup Utility
Page 55
3.7 Save&Exit
GOT3126T-834 User ’s Manual
AMI BIOS Setup Utility 49
Page 56
GOT3126T-834 User’s Manual
This page is intentionally left blank.
50 AMI BIOS Setup Utility
Page 57
GOT3126T-834 User ’s Manual
Chapter 4
Drivers Installation
4.1 System
GOT3126T-834 supports Windows 7(64bit), Windows 8/8.1, WES 7(64bit) and WE8S. To
facilitate the installation of system driver, please carefully read the instructions in this chapter
before start installing.
4.1.1 Win 7 (64bit)
1. Insert Driver CD and select the “\Drivers”.
2. Select all files and follow the installing procedure.
NOTE: Please install Microsoft KB2685811 before TXE installation under Windows 7, then
installing the drivers.
Don’t run “Step 4. USB3.0”driver’s installer (Setup.exe) from a USB storage device
(ie. external USB hard drive or USB thumb drive). For proper installation, please
copy driver files to a local hard drive folder and run from there.
If you set your system in “Hibernate mode” before you install “Step 2. Graphic”
driver, the monitor can’t display when you awake your system. Reboot your system
and the monitor will display. Please install graphic driver, and there is no display
problem with “Hibernate mode”.
Drivers Installation 51
Page 58
GOT3126T-834 User’s Manual
4.1.2 Win 8/8.x
1. Insert Driver CD and select the “\Drivers”.
3. Select all files and follow the installing procedure.
NOTE: If you set your system in “Hibernate mode” before you install “Step 2. Graphic”
driver, the monitor can’t display when you awake your system. Reboot your system
and the monitor will display. Please install graphic driver, and there is no display
problem with “Hibernate mode”..
52 Drivers Installation
Page 59
GOT3126T-834 User ’s Manual
Touch Screen
5-wire Analog Resistive type
Touch Screen Controller
PenMount 6000 USB Touch Screen Controller IC
Communications
USB interface
Resolution
1024 x 1024
Power Input
5V
Power Consumption
Active: 24.6mA / Idle Mode: 13.4mA
4.2 Touch Screen
The GOT3126T-834 uses the 5-wire analog resistive (flat front bezel type). There are the
specification and driver installation which are listed below.
4.2.1 Specification
4.2.2 Driver Installation- Windows 7/8.x
The GOT3126T-834 provides a touch screen driver that users can install it under the operating
system Windows 7/8.x. To facilitate installation of the touch screen driver, you should read the
instructions in this chapter carefully before you attempt installation.
1. Insert Driver CD and follow the path to select the “\Drivers\Step 7 - Touch”.
2. Follow the installing procedure and press OK.
3. Click Start menu and select “PenMount Utilities”; and then, a “PenMount Control Panel”
pops out.
Drivers Installation 53
Page 60
GOT3126T-834 User’s Manual
4. Select the “Standard Calibrate” tab.
5. Calibration:
To adjust the display with touch panel, click “Calibration” and follow the calibrate point to
do calibration; there are five points on screen for calibration.
6. Press OK.
54 Drivers Installation
Page 61
GOT3126T-834 User ’s Manual
4.3 Embedded O.S.
The GOT3126T-834 provides the WES 7 and WE8S Embedded. The O.S. is supported
devices which are listed below.
4.3.1 WES 7 & WE8S
Here are supported onboard devices:
Onboard Multi I/O
SATA HDD
USB
CRT/LCD display
10/100/1000 base-T Ethernet
CFast
Onboard Audio
Touch Screen
PenMount Touch screen
TM
or mSATA
Before you use it, please calibrate it.
1. Please find “PenMount Windows Universal Driver” from the start menu. Enter it and will
find another folder “Utility”. Please enter “Utility” and execute “Penmount Control Panel”
Drivers Installation 55
Page 62
GOT3126T-834 User’s Manual
2. There will be “PenMount 6000 USB” device. Please click to select it and then click the
“Configure” button.
3. Click the “Standard Calibration” and follow the procedure to finish calibration.
56 Drivers Installation
Page 63
GOT3126T-834 User ’s Manual
Drivers Installation 57
Page 64
GOT3126T-834 User’s Manual
This page is intentionally left blank.
58 Drivers Installation
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.