AXIOMTEK GOT3126T-832 User Manual

Page 1
GOT3126T-832
All-in-One
12.1” SVGA TFT Fanless Compact-Size PANEL PC
Page 2
ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information. Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third partys rights, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy, completeness or usefulness of any information in this document. Axiomtek does not make any commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Axiomtek Co., Ltd.
CAUTION
If you replace wrong batteries, it causes the danger of explosion. It is recommended by the manufacturer that you follow the manufacturers instructions to only replace the same or equivalent type of battery, and dispose of used ones.
Copyright 2013 Axiomtek Co., Ltd.
All Rights Reserved July 2013, Version A3 Printed in Taiwan
Page 3
iii
Safety Precautions
Before getting started, read the following important cautions.
1. Be sure to ground yourself to prevent static charge when installing the internal components. Use a grounding wrist strap and place all electronic components in any static-shielded devices. Most electronic components are sensitive to static electrical charge.
2. Disconnect the power cords from the GOT3126T-832 Series before making any installation. Be sure both the system and the external devices are turned OFF. Sudden surge of power could ruin sensitive components. Make sure the GOT3126T-832 Series is properly grounded.
3. Do not open the system’s top cover. If opening the cover for maintenance is a must, only a trained technician is allowed to do so. Integrated circuits on computer boards are sensitive to static electricity. To avoid damaging chips from electrostatic discharge, observe the following precautions:
Before handling a board or integrated circuit, touch an unpainted portion of the
system unit chassis for a few seconds. This will help to discharge any static electricity on your body.
When handling boards and components, wear a wrist-grounding strap, available
from most electronic component stores.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd. Windows® is a trademark of Microsoft Corporation.
IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation. Intel® and Pentium® are trademarks of Intel Corporation.
AMI is trademark of American Megatrend Inc. Other brand names and trademarks are the properties and registered brands of their
respective owners.
Page 4
iv
Table of Contents
Disclaimers ..................................................................................................... ii
Safety Precautions ........................................................................................ iii
Chapter 1 Introduction ............................................. 1
1.1 General Description ............................................................................ 1
1.2 Specifications ...................................................................................... 2
1.3 Dimensions and Outlines ................................................................... 4
1.4 I/O Outlets ............................................................................................ 5
1.5 Packing List ......................................................................................... 6
Chapter 2 Hardware and Installation ...................... 7
2.1 Open back cover ................................................................................. 8
2.2 CF card Installation ............................................................................. 9
2.3 Serial Ports Interface ........................................................................ 10
2.3.1 COM1&COM2 Connector ......................................................................... 10
2.4 Ethernet .............................................................................................. 11
2.5 Mountings: Panel / Wall / VESA ....................................................... 12
2.5.1 VESA-ARM/Wall-Mount ............................................................................ 12
2.5.2 Panel-mount Kit Assembly ........................................................................ 13
2.6 HDD Installation ................................................................................. 14
2.7 DRAM Installation .............................................................................. 16
2.8 Wireless LAN Card Installation ........................................................ 18
2.9 Power ................................................................................................. 19
Chapter 3 AMI BIOS Setup Utility .......................... 21
3.1 Starting ............................................................................................... 21
3.2 Navigation Keys ................................................................................ 21
3.3 Main Menu .......................................................................................... 22
3.4 Advanced Menu ................................................................................. 23
3.5 Chipset Menu ..................................................................................... 30
3.6 Boot Menu .......................................................................................... 32
3.7 Security Menu .................................................................................... 33
3.8 Save & Exit Menu .............................................................................. 34
Page 5
v
Chapter 4 Drivers Installation .............................. 37
4.1 System ............................................................................................... 37
4.2 Touch Screen ..................................................................................... 37
4.3 Embedded O.S. .................................................................................. 39
Page 6
vi
This page is intentionally left blank.
Page 7
GOT3126T-832 User’s Manual
Introduction 1
Chapter 1
Introduction
This chapter contains general information and detailed specifications of the GOT3126T-832. Chapter 1 includes the following sections:
General Description Specification Dimensions I/O Outlets Package List
1.1 General Description
The GOT3126T-832 adopts a 12.1-inch SVGA TFT LCD with 450-nit brightness and an Intel® AtomTM processor N2600 1.6 GHz to provide excellent computing performance and thermal resistance. This fanless platform is especially designed for operating under heavy-duty environment including steel refinery, oil pipe, ship, machine maker operating systems and many more. Having below abilities makes GOT3126T-832 surely a most robust and cost-effective solution.
Wide Operating Temperature Range
GOT3126T-832 features a technology of wide operating temperature range which allows it to work between -20°C to +55°C. It incorporates compact ID and fanless cooling system with a low power Intel® AtomTM processor N2600 1.6 GHz, making the platform a power-efficient solution.
Reliable and Stable Design
The GOT3126T-832 adopts a fan-less cooling system and a CompactFlash™ card, which makes it especially suitable for vibration-heavy environments, best for the transportation, ship, and industrial machinery markets. For high capacity storage requirement, GOT3126T-832 can work under 1.3G (10 ~ 500Hz, random for 2.5 HDD) in operation mode with a patent of anti-vibration design. The patent improves the system reliability and sustainability.
Page 8
GOT3126T-832 User’s Manual
2 Introduction
WLAN Antenna Supported (optional)
GOT3126T-832 has a PCI Express Mini Card slot for optional add-ons such as wireless LAN card for 802.11 b/g connections & 3G/GPRS application, graphics-enhanced video card, universal analog TV/FM tuner/AV capture card, and more. It also provides an optional fixed rotational WLAN antenna for wireless network connection.
More Features
GOT3126T-832 utilizes one 204-pin DDR3 SODIMM system memory max. up to 2GB, one SATA HDD and one CompactFlashTM slot. It provides over-current protection-fuse and a full set of I/O including 2 RS-232, 1 RS-232/422/485, 4 USB 2.0, 1 audio (line-out), 2 Gigabit Ethernet and 1 VGA. Additionally, this slim unit supports panel mount, wall mount (optional), VESA mount (optional) and desktop stand (optional).
1.2 Specifications
Main CPU Board
CPU
Intel
®
AtomTM N2600 1.6GHz processor onboard
System Chipset
Intel
®
NM10 Express
System Memory
One 204-pin DDR3 SO-DIMM socket Maximum memory up to 2GB
BIOS
America Megatrends BIOS
I/O System
Standard I/O
Two RS-232 and one RS-232/422/485 Four USB 2.0
Ethernet
Two RTL81111b Gigabit Ethernet
Audio
One Line-out
Expansion
One Mini card
Storage
One slot for CF card One SATA
Power connector
Phoenix power connector
Page 9
GOT3126T-832 User’s Manual
Introduction 3
System Specification
12.1” SVGA(800x600) LCD with LED backlight 5 wired resistive Touch Fanless Heat Dispensing Design IP65 aluminum front bezel Disk drive housing:
One 2.5 SATA drive
Net Weight
2.8 Kgs (6.78 lb)
Dimension (Main Body Size)
311.5mm x 56.9mm x 250mm
Operation Temperature
-20 to 55
Relative Humidity
20% to 90% @ 40, Non-Condensing
Power input
DC power 10~30V (phoenix type)
Note: All specifications and images are subject to change without notice. Note: If the operation temperature is higher than 40℃, the wide temperature HDD is
recommended to be used on the device.
Note: If the operation temperature is higher than 45℃, the wide temperature CF is
recommended to be used on the device.
Page 10
GOT3126T-832 User’s Manual
4 Introduction
1.3 Dimensions and Outlines
The following diagrams show the dimensions and outlines of GOT3126T-832.
Page 11
GOT3126T-832 User’s Manual
Introduction 5
1.4 I/O Outlets
Please refer to the following illustration for I/O locations of the GOT3126T-832.
No
Function
No
Function
1
POWER SWITCH (ATX)
7
COM 2 (RS-232)
2
Power Input connector (phoenix)
8
2X Ethernet (RJ-45)
3
2 X USB 2.0
9
2 X USB 2.0
4
VGA
10
AUDIO (LINE-OUT)
5
COM 3 (RS-232)
6 COM 1 (RS-232/422/485)
Page 12
GOT3126T-832 User’s Manual
6 Introduction
1.5 Packing List
When you receive the GOT3126T-832, the bundled package should contain the following items:
GOT3126T-832 unit x 1 Driver CD x1 Phoenix connector x 1 Panel mount kit x 6 Screws for HDD x 4
If you can not find the package or any items are missing, please contact Axiomtek distributors immediately.
Page 13
GOT3126T-832 User’s Manual
Hardware and Installation 7
Chapter 2
Hardware and Installation
The GOT326T-832 provides rich I/O ports and flexible expansions for you to meet different demand, for example CF card. The chapter will show you how to install the hardware. It includes:
Open back cover CompactFlash Card
Serial Port Ethernet Mounting Method Hard disk DRAM Wireless LAN Card Power
Page 14
GOT3126T-832 User’s Manual
8 Hardware and Installation
2.1 Open back cover
This section tells users how to open back cover. Please follow the steps below.
Step 1 Unscrew ten screws on the back cover. Please refer the photo below.
Step 2 Remove the back cover.
Page 15
GOT3126T-832 User’s Manual
Hardware and Installation 9
2.2 CF card Installation
The GOT3126T-832 provides one CF slot for users to install CompactFlash card. Please refer to the following instructions for installation:
Step 1 Unscrew a screw on the cover of CF card slot on left side of GOT.
Step 2 Stick mylar on the CF card.
Step 3 Insert the card into the socket.
Step 4 Close the cover of CF card slot and fix it. Installation completes.
Page 16
GOT3126T-832 User’s Manual
10 Hardware and Installation
2.3 Serial Ports Interface
The GOT3126T-832 has four serial ports. COM1 is RS-232/422/485, while COM2 and COM3 are RS-232.
The following table shows you the pin assignments of this connector:
Jumper
Description
Jumper Setting
COM 1
RS-232 (Default)
JP8 JP7
JP9
RS-422
JP8
JP7
JP9
RS-485
JP8
JP7
JP9
2.3.1 COM1&COM2 Connector
The COM1 and COM2 is a standard DB-9 connector. This connector is equipped with +5V level power capability on DCD and +12V level on RI by setting JP10 and JP11.
Jumper
Description
Default Jumper Setting
JP10
COM1 Port W/O Power: (3-5, 4-6) With Power: (1-3) DCD_+5V (2-4) RI_+12V
(3-5, 4-6)
JP11
COM2 Port W/O Power: (3-5, 4-6)(Default) With Power: (1-3) DCD_+5V (2-4) RI_+12V
(3-5, 4-6)
JP12
COM3 Port W/O Power: (3-5, 4-6)(Default) With Power: (1-3, 2-4)
(3-5, 4-6)
Page 17
GOT3126T-832 User’s Manual
Hardware and Installation 11
The pin assignment of RS-232/RS-422/RS-485 is listed on the following table. If you need COM1 port to support RS-422 or RS-485 mode, please refer to Jumper Settings
COM1 (SBC87832)
1 5
6 10
2.4 Ethernet
The GOT3126T-832 is equipped with a high performance Plug and Play Ethernet interface, full compliant with IEEE 802.3 standard, and can be connected with a RJ-45 LAN connector.
Please refer to detailed pin assignment list below:
Pin
Signal
1
23456
7
8
RJ-45
1
TX+ (Data transmission positive
2
TX- (Data transmission negative)
3
Rx+(Data reception positive)
4
RJ45 termination
5
RJ45 termination
6
Rx- (Data reception negative)
7
RJ45 termination
8
RJ45 termination
Pin
RS-232
RS-422
RS-485
1
DCD
TX-
Data-
2
RXD
TX+
Data+
3
TXD
RX+
N.C
4
DTR
RX-
N.C.
5
GND
No use
No use
6
DSR
No use
No use
7
RTS
No use
No use
8
CTS
No use
No use
9
RI
No use
No use
Page 18
GOT3126T-832 User’s Manual
12 Hardware and Installation
2.5 Mountings: Panel / Wall / VESA
There are 4 application options for the GOT3126T-832, Panel/Wall/Desktop/VESA mountings.
2.5.1 VESA-ARM/Wall-Mount
The GOT3126T-832 provides two ways for VESA mount: 100x100 mm. Screw four screws to fix the kit (option) in the back chassis.
Wall mount:
Page 19
GOT3126T-832 User’s Manual
Hardware and Installation 13
VESA mount:
2.5.2 Panel-mount Kit Assembly
The GOT3126T-832 is designed for panel mount application. To mount the GOT3126T-832, the standard set of mounting kit (included in the system packaging) is needed.
Page 20
GOT3126T-832 User’s Manual
14 Hardware and Installation
2.6 HDD Installation
The GOT3126T-832 provides a convenient Hard Disk Drive (HDD) bracket for users to install
2.5” SATA HDD. Please follow the steps:
Step 1 Refer section 2.1 to open the back cover. Step 2 Unscrew 4 screws to take off the HDD bracket.
Step 3 Fix the HDD on bracket by 4 screws.
Page 21
GOT3126T-832 User’s Manual
Hardware and Installation 15
Step 4 Fix the HDD bracket into the system, and plug the data and power cable to
HDD. Installation completes.
Page 22
GOT3126T-832 User’s Manual
16 Hardware and Installation
2.7 DRAM Installation
The GOT3126T-832 provides one 204-pin DDR3 SODIMM socket that support system memory up to 2GB. Please follow steps below to install the memory modules:
Step 1 Refer to section 2.1 to open the back cover and find out DIMM socket on main
board (SBC87832).
Step 2 Stick the thermal pad on the back cover and rip the red mylar from it.
Page 23
GOT3126T-832 User’s Manual
Hardware and Installation 17
Step 3 Insert the DRAM to the DIMM socket, and then push it down firmly until it is
clipped by the socket.
Step 4 Installation completes.
Page 24
GOT3126T-832 User’s Manual
18 Hardware and Installation
2.8 Wireless LAN Card Installation
The GOT3126T-832 provides one Mini card slot for user to install one wireless LAN card. When installing the wireless LAN card, refer to the following instructions and illustration:
Step 1 Refer to section 2.1 to open the back cover and find out mini-card slot on
main board.
Step 2 Insert the wireless LAN card to the slot. Push it down firmly until it is clipped
by the slot.
Step 3 Find the Antenna cable and connect it wireless LAN card.
Page 25
GOT3126T-832 User’s Manual
Hardware and Installation 19
Step 4 Remove the antenna plug from the top of back cover, then Install the antenna
on the antenna connector
2.9 Power
GOT3126T-832 equips with a phoenix type power connector. It adopts 10VDC to 30VDC. Please follow the signs on power connector to connect DC power source.
+: Power positive G: Safety ground :Power negative
Note: The safety ground must be connected to ensure the unit working appropriately.
Page 26
GOT3126T-832 User’s Manual
20 Hardware and Installation
This page is intentionally left blank.
Page 27
GOT3126T-832 User’s Manual
AMI BIOS Setup Utility 21
Chapter 3
AMI BIOS Setup Utility
This chapter provides users with detailed description how to set up basic system configuration through the AMIBIOS8 BIOS setup utility.
3.1 Starting
To enter the setup screens, follow the steps below: Turn on the computer and press the <Del> key immediately. After you press the <Delete> key, the main BIOS setup menu displays. You can access the other setup screens from the main BIOS setup menu, such as the Chipset and Power menus.
3.2 Navigation Keys
The BIOS setup/utility uses a key-based navigation system called hot keys. Most of the BIOS setup utility hot keys can be used at any time during the setup navigation process. These keys include <F1>, <F2>, <Enter>, <ESC>, <Arrow> keys, and so on.
Note: Some of the navigation keys differ from one screen to another.
Hot Keys
Description
 Left/Right
The Left and Right <Arrow> keys allow you to select a setup screen.
 Up/Down
The Up and Down <Arrow> keys allow you to select a setup screen or sub-screen.
+ Plus/Minus
The Plus and Minus <Arrow> keys allow you to change the field value of a particular setup item.
Tab
The <Tab> key allows you to select setup fields.
F1
The <F1> key allows you to display the general help screen.
F2
The <F2> key allows you to load previous values.
F3
The <F3> key allows you to load optimized defaults.
F4
The <F4> key allows you to save any changes you have made and exit setup. Press the <F4> key to save your changes.
Esc
The <Esc> key allows you to discard any changes you have made and exit the setup. Press the <Esc> key to exit the setup without saving your changes.
Enter
The <Enter> key allows you to display or change the setup option listed for a particular setup item. The <Enter> key can also allow you to display the setup sub- screens.
Page 28
GOT3126T-832 User’s Manual
22 AMI BIOS Setup Utility
3.3 Main Menu
When you first enter the Setup Utility, you will enter the Main setup screen. You can always return to the Main setup screen by selecting the Main tab. There are two Main Setup options. They are described in this section. The Main BIOS Setup screen is shown below
System Date/Time
Use this option to change the system time and date. Highlight System Time or System Date using the <Arrow> keys. Enter new values through the keyboard. Press the <Tab> key or the <Arrow> keys to move between fields. The date must be entered in MM/DD/YY format. The time is entered in HH:MM:SS format.
Page 29
GOT3126T-832 User’s Manual
AMI BIOS Setup Utility 23
3.4 Advanced Menu
Launch Storage OpROM
This item can enable or disable boot option for legacy mass storage devices with option ROM.
The Advanced menu also allows users to set configuration of the CPU and other system devices. You can select any of the items in the left frame of the screen to go to the sub menus:
ACPI Settings CPU Configuration IDE Configuration USB Configuration NCT6627UD Superior IO Configuration NCT6627UD HW Monitor JMB36X ATA Controller Configuration
For items marked with , please press <Enter> for more options.
Page 30
GOT3126T-832 User’s Manual
24 AMI BIOS Setup Utility
ACPI Settings
You can use this screen to select options for the ACPI Configuration, and change the value of the selected option. A description of the selected item appears on the right side of the screen.
ACPI Sleep State
Use this item to select the highest ACPI sleep state the system will enter.
Page 31
GOT3126T-832 User’s Manual
AMI BIOS Setup Utility 25
CPU Configuration
This screen shows the CPU Configuration, and you can change the value of the selected option.
Hyper-Threading Use this item to enable or disable Hyper-Threading Technology, which makes a single physical processor perform multi-tasking function as two logical ones.
Execute Disable Bit
XD can prevent certain classes of malicious buffer overflow attacks when combined with a supporting OS (Windows Server 2003 SP1, Windows XP SP2, SuSE Linux 9.2, RedHat Enterprise 3 Update 3).
Page 32
GOT3126T-832 User’s Manual
26 AMI BIOS Setup Utility
IDE Configuration
SATA Controller(s)
The optional settings are: [Disabled]; [Enabled].
Configure SATA as
The optional settings are: [IDE]; [AHCI].
Page 33
GOT3126T-832 User’s Manual
AMI BIOS Setup Utility 27
USB Configuration
You can use this screen to select options for the USB Configuration, and change the value of the selected option. A description of the selected item appears on the right side of the screen.
Legacy USB Support
The optional settings are: [Auto]; [Disabled]; [Enabled].
Page 34
GOT3126T-832 User’s Manual
28 AMI BIOS Setup Utility
NCT6627UD Super IO Configuration
You can use this screen to select options for the Super IO Configuration, and change the value of the selected option. A description of the selected item appears on the right side of the screen
Serial Port Configuration
Use this item to set parameters of serial port 0~1
Page 35
GOT3126T-832 User’s Manual
AMI BIOS Setup Utility 29
PC Health Status
This screen shows the Hardware Health Configuration, and a description of the selected item appears on the right side of the screen.
Page 36
GOT3126T-832 User’s Manual
30 AMI BIOS Setup Utility
3.5 Chipset Menu
The Chipset menu allows users to change the advanced chipset settings. You can select any of the items in the left frame of the screen to go to the sub menus:
Host Bridge
Host Bridge For items marked with , please press <Enter> for more options.
South Bridge
South Bridge For items marked with , please press <Enter> for more options.
Page 37
GOT3126T-832 User’s Manual
AMI BIOS Setup Utility 31
Memory Information
This item is for memory frequency and timing settings. Press <Enter> to go to the sub menu.
Page 38
GOT3126T-832 User’s Manual
32 AMI BIOS Setup Utility
3.6 Boot Menu
The Boot menu allows users to change boot options of the system.
Boot Settings Configuration
Setup Prompt Timeout
Use this item to set number of seconds to wait for setup activation key.
Bootup NumLock State
Use this item to select the power-on state for the NumLock.. The optional settings are: [On]; [Off].
GateA20 Active
If Upon Request is selected, GA20 can be disabled using BIOS services. If Always is selected, disabling G20 is not allowed; this option is useful when any RT code is executed above 1MB.
Option ROM Messages
Set display mode for option ROM. Configuration options are Force BIOS and Keep Current.
Interrupt 19 Capture
If this item is enabled, this function makes the option ROM to trap Interrupt 19.
Boot Option Priorities
These are settings for boot priority. Specify the boot device priority sequence from the available devices.
Page 39
GOT3126T-832 User’s Manual
AMI BIOS Setup Utility 33
3.7 Security Menu
The Security menu allows users to change the security settings for the system.
Administrator Password
This item indicates whether an administrator password has been set. If the password has been installed, Installed displays. If not, Not Installed displays.
User Password
This item indicates whether an user password has been set. If the password has been installed, Installed displays. If not, Not Installed displays.
Page 40
GOT3126T-832 User’s Manual
34 AMI BIOS Setup Utility
3.8 Save & Exit Menu
The Save & Exit menu allows users to load your system configuration with optimal or fail-safe default values.
Save Changes and Exit
When you have completed the system configuration changes, select this option to leave Setup and reboot the computer so the new system configuration parameters can take effect. Select Save Changes and Exit from the Exit menu and press <Enter>. Select Ok to save changes and exit.
Discard Changes and Exit
Select this option to quit Setup without making any permanent changes to the system configuration. Select Discard Changes and Exit from the Exit menu and press <Enter>. Select Ok to discard changes and exit.
Save Changes and Reset
When you have completed the system configuration changes, select this option to leave Setup and reboot the computer so the new system configuration parameters can take effect. Select Save Changes and Reset from the Save & Exit menu and press <Enter>. Select Yes to save changes and reset.
Discard Changes and Reset
Select this option to quit Setup without making any permanent changes to the system configuration and reboot the computer. Select Discard Changes and Reset from the Save & Exit menu and press <Enter>. Select Yes to discard changes and reset.
Save Changes
When you have completed the system configuration changes, select this option to save changes. Select Save Changes from the Save & Exit menu and press <Enter>. Select yes to save changes.
Page 41
GOT3126T-832 User’s Manual
AMI BIOS Setup Utility 35
Discard Changes
Select this option to quit Setup without making any permanent changes to the system configuration. Select Discard Changes from the Save & Exit menu and press <Enter>. Select Yes to discard changes.
Restore Defaults
It automatically sets all Setup options to a complete set of default settings when you select this option. Select Restore Defaults from the Save & Exit menu and press <Enter>.
Save as User Defaults
Select this option to save system configuration changes done so far as User Defaults. Select Save as User Defaults from the Save & Exit menu and press <Enter>.
Restore User Defaults
It automatically sets all Setup options to a complete set of User Defaults when you select this option. Select Restore User Defaults from the Save & Exit menu and press <Enter>.
Boot Override
Select a drive to immediately boot that device regardless of the current boot order.
Note: If you want to use a CF card that capacity is less than 2GB (such as 1GB,
512MB), we recommend you may switch “AHCI mode” to “IDE mode” with "Configure SATA as" of the BIOS setting. And please make sure that users of Windows embedded OS need to install with “IDE” driver.
Page 42
GOT3126T-832 User’s Manual
36 AMI BIOS Setup Utility
This page is intentionally left blank.
Page 43
GOT3126T-832 User’s Manual
Drivers Installation 37
Chapter 4
Drivers Installation
4.1 System
GOT3126T-832 supports Windows 7 32-bit and WES 7. To facilitate the installation of system driver, please carefully read the instructions in this chapter before start installing.
Step 1 Insert Driver CD and select the \Drivers”.
Step 2 Select all files and follow the installing procedure.
4.2 Touch Screen
The GOT3126T-832 uses the 5-wire analog resistve. There are the specification and driver installation which are listed below.
Specification
Touch Screen
5-wire Analog Resistive type
Touch Screen Controller
PenMount 6000 USB Touch Screen Controller IC
Communications
USB interface
Baud Rate
19200 baud rate fixed
Resolution
800 x 600
Power Input
5V
Power Consumption
Active: 24.6mA / Idle Mode: 13.4mA
Page 44
GOT3126T-832 User’s Manual
38 Drivers Installation
Driver Installation- Windows 7
The GOT3126T-832 provides a touch screen driver that users can install it under the operating system Windows 7. To facilitate installation of the touch screen driver, you should read the instructions in this chapter carefully before you attempt installation.
Step 1 Insert Driver CD and follow the path to select the \Drivers\Step 5 - Touch”.
Step 2 Follow the installing procedure and press OK. Step 3 Click Start menu and select “PenMount Utilities”; and then, a “PenMount
Control Panel” pops out.
Step 4 Select the “Standard Calibrate” tab.
Page 45
GOT3126T-832 User’s Manual
Drivers Installation 39
Step 5 Calibration:
To adjust the display with touch panel, click “Calibration” and follow the calibrate point to do calibration; there are five points on screen for calibration.
Step 6 Press OK.
Note: The windows may be out of rang, because the resolution requests 1024x768 or
above when using WIN 7.
Note: For the better system performance, please close the Windows AERO or change to
Windows Basic mode.
4.3 Embedded O.S.
The GOT3126T-832 provides the Windows 7 Embedded. The O.S. is supported devices which are listed below.
WES 7
Here are supported onboard devices:
Onboard Multi I/O SATA HDD USB CRT/LCD display 10/100/1000 base-T Ethernet Compact Flash Onboard Audio Touch Screen
Page 46
GOT3126T-832 User’s Manual
40 Drivers Installation
PenMount Touch screen
Before you can use and calibrate it, here is what you should do:
1. Set up Penmount touch device driver by executing C:\Penmount\ Windows 2000-XP V5.0\setup.exe. When the installation is finished, an icon “PM” appears on the Taskbar.
2. Calibrate Penmount touch by clicking on the “PM” icon, and the go on the calibration.
3. Restart the computer.
Please be informed if you use the Windows XP OS, the graphic driver supported by Intel is EMGD, there are three known issues as below:
Note: The Intel EMGD package does not include an HDMI audio driver, there will be an
unknown device under device manager.
Note: 3D function is not supported.
Note: LVDS and CRT can’t be disabled at the same time.
Loading...