AXIOMTEK GOT-3100T, GOT-3100TL, GOT-3108T User Manual

GOT-3100T/3100TL/3108T
All-in-One
10.4” TFT SVGA Fanless Touch Panel Computer
User’s Manual
i
Disclaimers
The information in this manual has been carefully checked and is believed to be accurate. AXIOMTEK Co., Ltd. assumes no responsibility for any infringements of patents or other rights of third parties, which may result from its use.
AXIOMTEK assumes no responsibility for any inaccuracies that may be contained in this document. AXIOMTEK makes no commitment to update or to keep current the information contained in this manual.
AXIOMTEK reserves the right to make improvements to this document and/or product at any time and without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of AXIOMTEK Co., Ltd.
©Copyright 2006 by AXIOMTEK Co., Ltd. All rights reserved. February 2006, Version A1 Printed in Taiwan
ii
Safety Approvals
CE Marking FCC Class A
FCC Compliance
This equipment has been tested and complies with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. If not installed and used in accordance with proper instructions, this equipment might generate or radiate radio frequency energy and cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measurers:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
Shielded interface cables must be used in order to comply with emission limits.ou
iii
Safety Precautions
Before getting started, read the following important cautions.
1. The GOT-3100T/3100TL/3108T does not come equipped with an operating system. An operating system must be loaded first before installing any software into the computer.
2. Be sure to ground yourself to prevent static charge when installing the internal components. Use a grounding wrist strap and place all electronic components in any static-shielded devices. Most electronic components are sensitive to static electrical charge.
3. Disconnect the power cord from the GOT-3100T/3100TL/3108T before making any installation. Be sure both the system and the external devices are turned OFF. Sudden surge of power could ruin sensitive components. Make sure the GOT-3100T/3100TL/3108T is properly grounded.
4. The brightness of the flat panel display decreases with usage. However, hours of use vary depending on the application environment.
5. Turn OFF the system power before cleaning. Clean the system using a cloth only. Do not spray any liquid cleaner directly onto the screen. The GOT-3100T/3100TL/3108T may come with or w/o a touchscreen. Although the touchscreen is chemical resistant, it is recommended that you spray the liquid cleaner on a cloth first before wiping the screen. In case your system comes without the touchscreen, you must follow the same procedure and not spray any cleaner on the flat panel directly.
6. Avoid using sharp objects to operate the touchscreen. Scratches on the touchscreen may cause malfunction or internal failure to the touchscreen.
7. The flat panel display is not susceptible to shock or vibration. When assembling the GOT-3100T/3100TL/3108T, make sure it is securely installed.
iv
8. Do not open the system’s back cover. If opening the cover for maintenance is a must, only a trained technician is allowed to do so. Integrated circuits on computer boards are sensitive to static electricity. To avoid damaging chips from electrostatic discharge, observe the following precautions:
9 Before handling a board or integrated circuit, touch an
unpainted portion of the system unit chassis for a few seconds. This will help to discharge any static electricity on your body.
9 When handling boards and components, wear a
wrist-grounding strap, available from most electronic component stores.
Trademarks Acknowledgments
AXIOMTEK is a trademark of AXIOMTEK Co., Ltd. IBM, PC/AT, PS/2, VGA are trademarks of International
Business Machines Corporation. Intel and Pentium are trademarks of Intel Corporation. MS-DOS, Microsoft C and QuickBASIC are trademarks of
Microsoft Corporation. VIA is a trademark of VIA Technologies, Inc. SST is a trademark of Silicon Storage Technology, Inc. UMC is a trademark of United Microelectronics Corporation. Other brand names and trademarks are the properties of their
respective owners.
v
This page does not contain any information.
vi
Table of Contents
Disclaimers........................................................................... ii
Safety Approvals................................................................iii
Safety Precautions ............................................................. iv
C h a p t e r 1 .....................................................................1
Introduction ..........................................................................1
1.1 General Description................................................1
1.2 Specifications..........................................................2
1.2.1 Main CPU Board...................................................... 2
1.2.2 I/O System............................................................... 2
1.2.3 System Specification.............................................. 3
1.3 Dimensions..............................................................4
1.4 I/O Outlets................................................................4
1.4 I/O Outlets................................................................5
1.5 Package List ............................................................6
C h a p t e r 2 .....................................................................7
Hardware Installation.........................................................7
2.1 HDD Installation ......................................................7
2.2 CF card Installation.................................................9
2.3 Wireless Card Installation....................................10
2.4 3 x Serial Ports ......................................................12
2.5 VGA ........................................................................14
2.6 Ethernet..................................................................14
2.7 Mountings: Panel / Wall / Desktop / VESA..........15
2.7.1 VESA-ARM/Wall-Mount........................................... 15
2.7.2 Desktop Kit Assembly ............................................. 16
2.7.3 Panel-mount Kit Assembly ..................................... 17
C h a p t e r 3......................................................................18
Driver Installation .............................................................18
3.1 Touch Screen ........................................................18
Table of Contents
vii
3.1.1 Driver Installation- Windows 2000/XP.................... 19
3.2 Embedded O.S.........................................................22
3.2.1 Windows XP Embedded..........................................22
3.2.2 Windows CE.NET 5.0 ................................................ 22
viii
Table of Contents
GOT-3100T/3100TL/3108TT User’s Manual
C h a p t e r 1
Introduction
This chapter contains the general information and the detail specifications of the GOT-3100T/3100TL/3108T. Chapter 1 includes the following sections:
General Description System Specification Dimensions
I/O Outlets Utilities Supported Package List
1.1 General Description
The GOT-3100T/3100TL/3108T is a fan-less and compact-size touch panel computer, and is equipped with a 10.4" TFT LCD display and low power consumption CPU, Celeron M 1GHz/0K. The GOT-3100T/3100TL/3108T supports Windows® 2000/XP, Windows® CE.NET, Windows® XP embedded, and Linux. The panel is able to install in a CompactFlash™ card and provides a MiniPCI slot for wireless module.
GOT-3100T: 10.4” TFT SVGA Fanless Touch Panel Computer
w/ High brightness
GOT-3100TL: 10.4” TFT SVGA Fanless Touch Panel
Computer(Light version)
GOT-3108T: 10.4” TFT SVGA Fanless Touch Panel Computer
w/ NEMA4X Stainless Front Bezel
Reliable and Stable Design
The GOT-3100T/3100TL/3108T adopts a fan-less cooling system and a CompactFlash™ card, which makes it especially suitable for vibration-heavy environments, best for the transportation, ship, and industrial machinery markets.
Embedded O.S. Supported
The GOT-3100T/3100TL/3108T not only supports Windows but also supports embedded OS, such as Windows
®
CE.NET, and
®
2000/XP,
Introduction
1
GOT-3100T/3100TL/3108T User’s Manual
Windows
®
XP embedded. For storage device, the GOT-3100T/3100TL/3108T supports 2.5" HDD or CompactFlash™ card.
Industrial-grade Product Design
The GOT-3100T/3100TL/3108T has an incredible design that can be used in different industrial harsh environments.
A fuse helps prevent over-voltage for power input.  Stainless steel back chassis and Aluminum front bezel meets
the IP65/NEMA4 standard.
For connecting other devices, the GOT-3100T/3100TL/3108T
also features several interfaces: USB, Ethernet, and RS-232/422/485.
1.2 Specifications
1.2.1 Main CPU Board
CPU: Intel® Celeron® M ULV 1GHz/0K onboard. System Chipset: Intel® 852GM+ICH 4 BIOS: Award 4Mbit with RPL/PEX LAN boot ROM,
SmartView and customer CMOS backup.
System Memory: One 200-pin DDR DIMM socket.
Maximum up to 1GB
1.2.2 I/O System
Standard I/O:
3 x serial ports
2 x RS-232,
1 x RS-232/422/485
2 x USB 2.0
2
Introduction
GOT-3100T/3100TL/3108TT User’s Manual
Ethernet:
- RJ45 x1
Expansion Slot:
- MiniPCI for wireless module
Audio
1.2.3 System Specification
10.4” TFT LCD Heat dispensing design Net weight:
4.1 Kg
Dimension (main body size):
290x71.9x248mm
Operating temperature: O° to 45°C ; Relative
umidity:40%
Relative humidity: 10% to 90% @ 40° C, on-condensing  Vibration (operating):
5 to 500 Hz, 1.3 G random ( install HDD ) 5 to 500 Hz, 2.0 G random ( install CompactFlash card )
3
GOT-3100T/3100TL/3108T User’s Manual
1.3 Dimensions
The following diagrams show the dimensions and outlines of GOT-3100T/3100TL/3108T
4
GOT-3100T/3100TL/3108TT User’s Manual
1.4 I/O Outlets
The following figure shows the I/O locations of the GOT-3100T/3100TL/3108T. Most of the I/O connectors are located on the back panel of the GOT-3100T/3100TL/3108T
1 2
Power connector
1:
Audio
2:
COM4
3:
COM2
4:
COM1
5:
4
4
3
3
6 7 8 91 2
6 7 8 9
5
5
USB v2.0 * 2
6:
PS2 keyboard/mouse
7:
Ethernet (RJ45)
8:
VGA
9:
5
GOT-3100T/3100TL/3108T User’s Manual
1.5 Package List
When you receive the GOT-3100T/3100TL/3108T there are following items in the package. If you can not find it, please contact AXIOMTEK distributors.
1. GOT-3100T/3100TL/3108T x 1
2. Panel mount kit x 6
3. CD driver x1
4. Desktop kit x 2 (optional)
5. VESA ARM/Wall-mount kit(optional)
6
GOT-3100T/3100TL/3108TT User’s Manual
C h a p t e r 2
Hardware Installation
The GOT-3100T/3100TL/3108T provides lots of flexible ways for you to select different configuration such as HDD,(recommend wide temperature HDD) CF card and more. The chapter will show you how to install the hardware. It includes:
2.1 HDD Installation
The GOT-3100T/3100TL/3108T offers a convenient drive bay module for users to install HDD. The GOT-3100T/3100TL/3108T offers one
2.5” HDD drive for users to install. Please follow the steps:
1. Take out the, HDD bracket kit, 4 anti-vibration screws, 4
anti-vibration rubbers and 4 bracket screws from the accessory package.
2. Screw 4 anti-vibration screws and fix HDD on the bracket kit.
7
GOT-3100T/3100TL/3108T User’s Manual
3. Fix the HDD kit to system by 4 scre ws.
8
GOT-3100T/3100TL/3108TT User’s Manual
2.2 CF card Installation
The GOT-3100T/3100TL/3108T offers a slot for users to install CF card. When installing the CF card, refer to the following instructions and illustration:
1. Open the back cove r. Find SBC84810 and turn to ba ck side.
2. Install user’s CF card.
9
GOT-3100T/3100TL/3108T User’s Manual
2.3 Wireless Card Installation
The GOT-3100T/3100TL/3108T provides one miniPCI slot for user to install one wireless card. When installing the wireless card, refer to the following instructions and illustration:
1. Open the back cove r and find SBC84810 and AX93 200
2. Inst all MiniPCI wireless card.
10
GOT-3100T/3100TL/3108TT User’s Manual
3. Conne ct cable from antenna to wireless card..
11
GOT-3100T/3100TL/3108T User’s Manual
2.4 3 x Serial Ports
The connector, COM 1, is a DB-9 connector, and the following table shows the pin assignments of this connector.
COM1 Port Connectors
Pin Signal Name
1 2 3 4 5 6 7 8 9
DCD, Data carrier detect RXD, Receive data TXD, Transmit data DTR, Data terminal ready GND, ground DSR, Data set ready RTS, Request to send CTS, Clear to send RI, Ring indicator
COM1
COM2 Port Connectors: CN9
The RS-232 pin assignments are listed on the following table.
Pin Description Pin
Data Carrier Detect
1
(DCD) Receive Data (RXD)
3
Transmit Data (TXD)
5
Data Terminal Ready
7
(DTR) Ground (GND)
9
12
2 4
6 8
10
Description
Data Set Ready (DSR) Request to Send (RTS)
Clear to Send (CTS) Ring Indicator (RI) NC
CN9
1 3
5 7
9
2 4
6 8
10
GOT-3100T/3100TL/3108TT User’s Manual
The RS-422/485 pin assignments for COM2 are listed below.
Pin #
1 2 3 4 5 6 7 8 9
10
R2-422 RS-485
No connector No connector
No connector No connector
No connector No connector
No connector No connector
No connector No connector
Signal Name
TX- DATA-
TX+ DATA+
RX+ No connector
RX- No connector
GND GND
13
GOT-3100T/3100TL/3108T User’s Manual
2.5 VGA
The GOT-310 0T/310 0TL/3108T has an analog RGB interface connector. It is able to connect to an expansion CRT monitor, and the system can display on both the flat panel and the CRT simultaneously.
2.6 Ethernet
Ethernet RJ-45 Connector: LAN1
The GOT-3100T/3100TL/3108T is equipped with a high performance Plug and Play Ethernet interface which is fully compliant with the IEEE
802.3 standard, and consisting of a RJ-45 connector LAN
3.4.15.1 Pin Assignment
LAN1: RJ-45 Connector Pin Assignment
Pin Signal
Tx+ (Data transmission
1
positive Tx- (Data transmission
2
negative) Rx+(Data reception
3
positive) 4 RJ45 termination 5 RJ45 termination
Rx- (Data reception
6
negative) 7 RJ45 termination 8 RJ45 termination
1
234567
RJ-45
8
14
GOT-3100T/3100TL/3108TT User’s Manual
2.7 Mountings: Panel / Wall / Desktop / VESA
There are 4 application options for the GOT-3100T/3100TL/3108T, Panel/Wall/Desktop/VESA mountings.
2.7.1 VESA-ARM/Wall-Mount
The GOT-3100T/3100TL/3108T prov ides two ways for VESA mount: 75x75 mm./100x100mm
Screw four screws to fix the kit (optional) in the side chassis.
15
GOT-3100T/3100TL/3108T User’s Manual
2.7.2 Desktop Kit Assembly
The GOT-3100T/3100TL/3108T is designed for desktop application. Screw 4 screws to fix the kit (optional) in the side chassis.
16
GOT-3100T/3100TL/3108TT User’s Manual
2.7.3 Panel-mount Kit Assembly
The GOT-3100T/3100TL/3108T is designed for panel mount application. To mount the GOT-3100T/3100TL/3108T, the standard set of mounting kit (included in the system packaging) is needed.
17
GOT-3100T/3100TL/3108T User’s Manual
C h a p t e r 3
Driver Installation
GOT-3100T/3100TL/3108 could support with Windows 2000/XP. To facilitate installation system driver, you should read the instructions in this chapter carefully before you attempt installation.
1. Insert Driver CD and select the “\GOT-3100T series\Driver\”.
2. Select all files and follow the install procedure.
3.1 Touch Screen
Specification(GOT-3100T/3108T)
Touch Screen: Touch Screen Controller: Communications: Contact bounce: Power Input: Power Consumption: Board Size: Operating Temperature:
18
For 5-wire analog resistive type Penmount 9036BH RS-232 < 15ms
5.5V DC or less 20mA (maximum)
248.92mmx186.69mm
-10℃ ~ 60℃ Humidity less than 85% RH
GOT-3100T/3100TL/3108TT User’s Manual
Specification(GOT-3100TL)
Touch Screen: Touch Screen Controller: Communications: Contact bounce: Power Input: Power Consumption: Board Size: Operating Temperature:
For 5-wire analog resistive type Penmount 9036BH RS-232 < 15ms
5.5V DC or less 20mA (maximum)
248.92x186.69mm
-10℃ ~ 60℃ Humidity less than 85% RH
3.1.1 Driver Installation- Windows 2000/XP
The touch screen of GOT-3 100T/3100TL/3108T provides a driver for use with Windows 2000/XP. To facilitate installation of the touch screen driver, you should read the instructions in this chapter carefully before you attempt installation.
1. Insert Driver CD and select the “\GOT-3100T series\ Driver\Penmount\Driver\Windows 2000-XP Driver V5.0(WHQL)\Setup.exe”
19
GOT-3100T/3100TL/3108T User’s Manual
2. Follow the install procedure and press OK.
3. Click Start menu and select “PenMount Utilities”. You can see PenMount Control Panel
4. Select the “Standard Calibrate” tab
20
GOT-3100T/3100TL/3108TT User’s Manual
5. Calibration:
To adjust the display with touch panel, click “Calibration” and follow the calibrate point to do calibration; there are five points on screen for calibration.
6. Press OK.
21
GOT-3100T/3100TL/3108T User’s Manual
3.2 Embedded O.S.
3.2.1 Windows XP Embedded
Supported onboard devices are as follows:
Onboard Multi I/O
Floppy drive 16C550 UARTs compatible serial port IrDA for wireless communication
Onboard IDE
IDE HDD
 USB  PS2 Keyboard and mouse  CRT/LCD display(Default 18bits Resolution 800x600)  10/100 base-T Ethernet  Compact flash  Onboard audio  Audio  Touch Screen
PenMount Touch screen
GOT-3100T/3100TL/3108T has Penmount touch screen on COM3, which is disabled by default.
Before you can use and calibrate it, you should :
1. Set up Penmount touch device driver by executing c:\Penmount\ Windows 2000-XP V5.0\setup.exe. When installation finished, an icon “PM” appears on Taskbar .
2. Calibrate Penmount touch by clicking on “PM” icon and doing calibration
3. Restart computer.
3.2.2 Windows CE.NET 5.0
Supported onboard devices are as follows:
Onboard Multi I/O
Floppy drive 16C550 UARTs compatible serial port
22
GOT-3100T/3100TL/3108TT User’s Manual
IrDA for wireless communication
Onboard IDE
IDE HDD
 USB  PS2 Keyboard and mouse  CRT/LCD display  10/100 base-T Ethernet  Compact flash  Onboard audio  Audio  Touch Screen
Calibration Touch Screen
In this image we add PenMount Touch drivers and utilities. It is customized for 800 x 600.
Calibration:
1. Click “Calibration” on desktop to calibrate touch screen.
2. In the start\programs menu, select save registry”, thus Calilbration data will be saved and effective in next boot.
23
Loading...