Page 1
GOT107W-319
All-in-One
7” WSVGA TFT Fanless Touch Panel
Computer with Intel® Celeron®
Processor N3350 onboard or Intel®
Pentium® Processor N4200
User’s Manual
Page 2
Disclaimers
This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or rights of any
third party, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make any
commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written permission of Axiomtek Co., Ltd.
CAUTION
Wrong type of batteries may cause explosion. It is recommended that users only replace with
the same or equivalent type of batteries as suggested by the manufacturer once properly
disposing of any used ones.
Copyright 2019 Axiomtek Co., Ltd.
All Rights Reserved
June 2019, Version A1
Printed in Taiwan
ii
Page 3
Safety Precautions
Before getting started, read the following important precautions.
1. Be sure to ground yourself to prevent static charge when installing the internal
components. Use a grounding wrist strap and place all electronic components in any
static-shielded devices. Most electronic components are sensitive to static electrical
charge.
2. Disconnect the power cords from the GOT107W-319 Series before making any
installation. Be sure both the system and the external devices are turned OFF. Sudden
surge of power could ruin sensitive components. Make sure the GOT107W-319 series is
properly grounded.
3. Do not open the top cover of the system. If opening the cover for maintenance is a must,
only a trained technician is allowed to do so. Integrated circuits on computer boards are
sensitive to static electricity. To avoid damaging chips from electrostatic discharge,
observe the following precautions:
Before handling a board or integrated circuit, touch an unpainted portion of the
system unit chassis for a few seconds. This will help to discharge any static
electricity on your body.
When handling boards and components, wear a grounding wrist strap, available
from most electronic component stores.
Trademark Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
Windows® is a trademark of Microsoft Corporation.
IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation.
Intel® and Pentium® are trademarks of Intel Corporation.
AMI is a trademark of American Megatrend Inc.
Other brand names and trademarks are the properties and registered brands of their
respective owners.
iii
Page 4
Table of Contents
Disclaimers ..................................................................................................... ii
Safety Precautions ........................................................................................ iii
Chapter 1 Introduction ............................................. 1
1.1 General Description ............................................................................ 1
1.2 GOT107W-319 Specifications ............................................................. 2
1.2.1 Main CPU Board ......................................................................................... 2
1.2.2 I/O System ................................................................................................... 2
1.2.3 System Specifications ................................................................................. 3
1.3 Dimensions .......................................................................................... 4
1.4 I/O Outlets ............................................................................................ 5
1.5 Packing List ......................................................................................... 6
Chapter 2 Hardware and Installation ...................... 7
2.1 Jumper and Connector Settings ........................................................ 7
2.1.1 Jumper Settings .......................................................................................... 8
2.1.2 Connector Settings ...................................................................................... 9
2.2 Mountings – Panel/Wall/Desktop/VESA .......................................... 13
2.2.1 Panel-Mounting (optional) ......................................................................... 13
2.2.2 Assembling the Wall-Mount Bracket ......................................................... 15
2.2.3 Assembling the stand ................................................................................ 16
2.3 Storage Installation ........................................................................... 17
2.3.1 mSATA Installation .................................................................................... 17
2.3.2 MicroSD Card Installation ......................................................................... 18
2.4 DRAM Installation .............................................................................. 19
2.5 M.2 Wireless Card Installation .......................................................... 20
2.6 Power Input (AC to DC cable) .......................................................... 21
Chapter 3 AMI BIOS Setup Utility .......................... 23
3.1 Navigation Keys ................................................................................ 23
3.2 Main Menu .......................................................................................... 24
3.3 Advanced Menu ................................................................................. 25
3.3.1 Serial Port Configuration ........................................................................... 26
3.3.2 Hardware Monitor ...................................................................................... 27
3.3.3 Trusted Computing .................................................................................... 28
3.3.4 ACPI Settings ............................................................................................ 29
3.3.5 CPU Configuration .................................................................................... 30
iv
Page 5
3.3.6 SATA Configuration ................................................................................... 31
3.3.7 USB Configuration..................................................................................... 32
3.4 Chipset Menu ..................................................................................... 33
3.4.1 North Bridge .............................................................................................. 34
3.4.2 South Bridge .............................................................................................. 35
3.5 Security Menu .................................................................................... 36
3.6 Boot Menu .......................................................................................... 37
3.7 Save & Exit Menu .............................................................................. 38
Chapter 4 Drivers Installation .............................. 39
4.1 System ............................................................................................... 39
4.1.1 Windows 10 ............................................................................................... 39
4.2 Touch Screen ................................................................ ..................... 39
Appendix A Watchdog Timer & DIO Programming ... 41
About Watchdog Timer ................................................................................ 41
How to Use Watchdog Timer ....................................................................... 41
WDT Sample Program ................................................................................. 43
How to Use DIO Software Programming ................................ .................... 43
v
Page 6
This page is intentionally left blank.
vi
Page 7
GOT107W-319 User’s Manual
Chapter 1
Introduction
This chapter contains general information and detailed specifications of the GOT107W-319,
including the following sections:
General Description
Specifications
Dimensions
I/O Outlets
Package List
1.1 General Description
The GOT107W-319 is a fanless and compact-size medical touch panel computer, equipped
with a 7” TFT LCD display and low power consumption Intel® Celeron® Processor N3350
(with 2M cache, up to 2.4 GHz) or Intel® Pentium® Processor N4200 (with 2M Cache, up to
2.5 GHz). This panel computer is compatible with Windows 10 and can house an mSATA for
storage and one M.2 card slot for wireless connection. Its excellent ID and friendly user
interface make it a professional yet easy-to-use panel computer. The GOT107W-319 is ideal
for applications with limited spaces in factory automation, building automation and more.
GOT107W-319: 7” TFT WSVGA Fanless Touch Panel Computer
Reliable and stable design
The GOT107W-319 adopts a fanless cooling system which makes it suitable for
environments prone to vibration.
Embedded O.S. supported
The GOT107W-319 supports not only Windows 10(64bit), but also embedded O.S. In
terms of storage device, the GOT107W-319 supports an mSATA.
Industrial-grade product design
The GOT107W-319 was adaptively designed to be used in different industrial
environments.
The GOT107W-319 comes with an IP65-rated front panel and its whole enclosure meets the
IPX1 standard.
For connecting other devices, the GOT107W-319 also features several interfaces: USB,
Ethernet, and RS-232/422/485.
Introduction 1
Page 8
GOT107W-319 User’s Manual
1.2 GOT107W-319 Specifications
1.2.1 Main CPU Board
CPU
Intel® Celeron® Dual Core Processor N3350 (2M Cache, up to 2.4 GHz) onboard.
Intel® Pentium® Quad Core Processor N4200 (2M Cache, up to 2.5 GHz) onboard.
System memory
One 204-pin DDR3L-1600 SO-DIMM socket
Maximum memory up to 8 GB
BIOS
American Megatrends BIOS
1.2.2 I/O System
Standard I/O
One RS-232/422/485 port
One RS-232 port
Two USB 3.0 ports
Ethernet
Two RJ45 Giga Ethernet ports
Expansion
One M.2(E Key) slot for wireless module
Storage
One mSATA
MicroSD Card slot
Power connector
GOT107W-319: 12 VDC with an external 36W AC adapter and a screw type
connector.
2 Introduction
Page 9
1.2.3 System Specifications
7” WSVGA (1024 x 600) LCD with LED backlight
Projected capacitive multi-touch
Fanless heat dissipation design
Disk drive housing
mSATA
MicroSD card slot
Net weight
0.7 kg
Dimension (main body size)
192 mm x 145 mm x 37.4 mm
Operation temperature
0℃ to 50℃
Relative humidity
GOT107W-319 User’s Manual
10% to 90% @ 40℃, -non-condensing
Vibration
2.0 G, 5 to 500 Hz, random (with mSATA storage)
Power input
External 12V 36W AC adapter
— Power input: 100 to 240 VAC
— Power output: 12 VDC, Max. 3A
Cable for AC screw type connector to DC source for 9~24V DC
NOTE All specifications and images are subject to change without notice.
Introduction 3
Page 10
GOT107W-319 User’s Manual
1.3 Dimensions
This diagram shows you dimensions and outlines of the GOT107W-319.
This diagram shows you the dimensions of the GOT107W-319 cutout
4 Introduction
Page 11
GOT107W-319 User’s Manual
No
Function
No
Function
1
Power button
6
COM 1 (RS-232/422/485)
2
Power input connector
7
COM2
3
AT/ATX switch
8
Micro SD Card slot
4
Ethernet (RJ-45) x 2
9
Speaker x 2
5
USB3.0 x 2
1.4 I/O Outlets
Please refer to Figures 1-1 and Table 1-1 for I/O locations at the bottom of the
GOT107W-319.
Figure 1-1 Front view of the GOT107W-319
Figure 1-1 Bottom view and back view of the GOT107W-319
Table 1-1 Descriptions of I/O functions at the bottom of the GOT107W-319
Introduction 5
Page 12
GOT107W-319 User’s Manual
1.5 Packing List
A complete bundled package of the GOT107W-319 should contain the following items:
GOT107W-319 x 1
Driver disc x 1
Power adapter & power cord (GOT107W-319-J)
AC to DC cable (GOT107W-319-DC)
Please contact an Axiomtek distributor immediately if you cannot find the package or any of the
above-mentioned items is missing.
6 Introduction
Page 13
GOT107W-319 User’s Manual
Chapter 2
Hardware and Installation
The GOT107W-319 provides rich I/O ports and flexible expansions for users to meet different
demands. The section is describing hardware installation, including the following subsections:
Jumper and Connector Settings
Port Definitions
Hardware Installation
Mounting Methods
Connecting the Power Input
2.1 Jumper and Connector Settings
Diagram 2-1 Component side of the board
Hardware and Installation 7
Page 14
GOT107W-319 User’s Manual
Jumper
★ Default Setting
Jumper Setting
JP3
★ Normal
Clear CMOS
Short 1-2
Short 2-3
Diagram 2-2 Solder side of the board
2.1.1 Jumper Settings
By making proper jumper settings, users can configure the board SBC87319 to suit the needs
of their applications.
Table 2-1 shows the default jumper settings for the SBC87319.
Table 2-1 Default jumper settings
NOTE: Items marked with ★ are for default settings.
8 Hardware and Installation
Page 15
GOT107W-319 User’s Manual
Label
Connectors
CN4
Speaker connector
CN5
SIM socket
CN7
Mini PCI-Express Card socket
CN11
USB2.0 connector (optional with touch controller)
CN15
USB2.0 connector
CN17
DIO connector
CN19
M.2 E key 2230 type
CN23
USB3.0 connector
CN24
Power DC in connector
SW1
Power button
LAN1/LAN2
Ethernet connector
COM1
COM Port connector
COM2
COM Port connector
SW2
AT/ATX switch
SCN1
SD card connector
2.1.2 Connector Settings
The connectors on the CPU Board allow the CPU Board to connect with other parts of the
system. Ensure that all connectors are in place and firmly attached. Table 2-2 lists the function
of each connector on the Board SBC87319.
Table 2-2 Connector Settings
Hardware and Installation 9
Page 16
GOT107W-319 User’s Manual
Pin
Description
1
SPKOUT_L+
2
SPKOUT_L-
3
SPKOUT_R+
4
SPKOUT_R-
5
GND
Pin
Description
1
USB Power
2
D-
3
D+ 4 GND
5
GND
Pin
Description
Pin
Description
1
USB2_PWR
2
USB2_PWR
3
USB_DN
4
USB_DN
5
USB_DP
6
USB_DP
7
GND
8
GND
9
GND
10
GND
Speaker connector: CN4
USB2.0 connector: CN11
USB2.0 connector: CN15
10 Hardware and Installation
Page 17
Pin
Description
Pin
Description
1
+5V 2 +5V 3 GPIO1
4
GPIO2
5
GPIO3
6
GPIO4
7
GPIO5
8
GPIO6
9
GPIO7
10
GPIO8
11
GND
12
GND
Pin
RS232
[*]
RS422
[*]
RS485
[*]
1
DCD#
TX-
485-
2
RXD
TX+
485+
3
TXD
RX+
NC
4
DTR#
RX-
NC
5
GND
GND
GND
6
DSR#
NC
NC
7
RTS#
NC
NC
8
CTS#
NC
NC
9
RI#
[**]
NC
NC
DIO connector: CN17
COM Port connector: COM1
GOT107W-319 User’s Manual
[*]: Signals of COM1 can be RS-232/422/485 by selecting BIOS table.
[**]
: Pin 9 of COM1 can be RI/5V/12V by selecting BIOS table.
Hardware and Installation 11
Page 18
GOT107W-319 User’s Manual
Pin
RS232
1
DCD#
2
RXD
3
TXD
4
DTR#
5
GND
6
DSR#
7
RTS#
8
CTS#
9
RI#
Pin
Description
1
Disable auto power on (Default)
2
Enable auto power on
COM Port connector: COM2
AT/ATX switch: SW2
12 Hardware and Installation
Page 19
GOT107W-319 User’s Manual
2.2 Mountings – Panel/Wall/Desktop/VESA
There are several mounting ways for the GOT107W-319: Wall, desktop, VESA and panel
mountings.
2.2.1 Panel-Mounting (optional)
The GOT107W-319 is designed for panel mount application.
Step1 Sticks four sealing pads on the edges of the chassis.
Step2 Assemble the panel kit onto the chassis and fasten the five screws.
Hardware and Installation 13
Page 20
GOT107W-319 User’s Manual
Panel Mount Dimension
14 Hardware and Installation
Page 21
GOT107W-319 User’s Manual
2.2.2 Assembling the Wall-Mount Bracket
The GOT107W-319 provides VESA mount: 75 x 75 mm. Screw four screws to fix the kit in the
back chassis.
Step 1 Find out the Screw holes to assemble the wall mount bracket on the back side
of the chassis with 4 screws
Wall-Mount Bracket Dimension
Hardware and Installation 15
Page 22
GOT107W-319 User’s Manual
2.2.3 Assembling the stand
The GOT107W-319 provides VESA mount: 75 x 75 mm. Screw four screws to fix the stand kit
in the back chassis.
Find out the Screw holes to assemble the stand kit with 4 screws as red mark shown in
the below picture
16 Hardware and Installation
Page 23
GOT107W-319 User’s Manual
2.3 Storage Installation
2.3.1 mSATA Installation
The GOT107W-319 provides a Mini Card slot for users to install mSATA. Please refer to the
following instructions for installation:
Step 1 Turn off the system, and unplug the power cord.
Step 2 Remove the back cover.
Step 3 Locate the Mini Card slot on the main board.
Hardware and Installation 17
Page 24
GOT107W-319 User’s Manual
Step 4 Insert the mSATA card into slot 1. Screw it firmly on the slot.
NOTE The type of screws used for the Mini Card slot is M12.
2.3.2 MicroSD Card Installation
The GOT107W-319 provides one MicroSD card slot for users to install a MicroSD card. Please
choose slot 1 when installing an mSATA card and refer to the following instructions and
illustrations.
Step 1 Push the MicroSD card into the slot until it has been locked firmly.
18 Hardware and Installation
Page 25
GOT107W-319 User’s Manual
2.4 DRAM Installation
The GOT107W-319 provides one 204-pin DDR3L SODIMM socket that supports system
memory up to 8GB. Please follow steps below to install the memory modules:
Step 1 Insert the DRAM into the DIMM socket, and then push it down firmly until it is
clipped by the socket.
Step 2 Insert the DRAM into the DIMM socket, and then push it down firmly until it is
clipped by the socket.
Hardware and Installation 19
Page 26
GOT107W-319 User’s Manual
2.5 M.2 Wireless Card Installation
The GOT107W-319 provides one Mini card slot for users to install mSATA. Please choose slot
1 when installing an mSATA card and refer to the following instructions and illustrations:
Step 1 Open the back cover and locate the M.2 card slot on the main board in the
marked area below.
Step 2 Insert the M.2 wireless card into the M.2 slot as shown in the red mark area.
Step 3 Screw the card firmly on the slot and connect the antenna cable, as shown in
the red mark area.
20 Hardware and Installation
Page 27
GOT107W-319 User’s Manual
Pin
Description
Color
1
+: Power positive
White
2
－:Power negative
Black
2.6 Power Input (AC to DC cable)
Axiomtek provides an optional cable for the DC jack connector to connect to a DC source. It
adopts 9~24VDC. Please follow the signs on the power connector to connect to a DC power
source.
NOTE The safety ground must be connected to ensure proper operation of the unit.
Hardware and Installation 21
Page 28
GOT107W-319 User’s Manual
This page is intentionally left blank.
22 Hardware and Installation
Page 29
GOT107W-319 User’s Manual
Hot Keys
Descriptions
<> and <>
Left/Right
The <> and <> keys are used to select a setup screen.
<> and <>
Up/Down
The <> and <> keys are used to select a setup screen or
sub-screen.
<+> and <>
Plus/Minus
The <+> and <> keys you are used to change the field value of a
particular setup item.
<Tab>
The <Tab> key is used to select setup fields.
<F1>
The <F1> key is used to display the general help screen.
<F2>
The <F2> key is used to load previous values.
<F3>
The <F3> key is used to load optimized defaults.
<F4>
The <F4> key is used to save any changes made then exit the setup.
Press the <F4> key to save any changes.
<Esc>
The <Esc> key is used to discard any changes made then exit the
setup. Press the <Esc> key to exit the setup without saving your
changes.
<Enter>
The <Enter> key is used to display or change the setup option listed
for a particular setup item. The <Enter> key is also used to display
the setup sub- screens.
Chapter 3
AMI BIOS Setup Utility
This section provides users with detailed descriptions about how to set up basic system
configuration through the AMI BIOS setup utility.
3.1 Navigation Keys
The BIOS setup/utility uses a key-based navigation system called hot keys. Most of the BIOS
setup utility hot keys can be used at any time during the setup navigation process.
These keys include <F1>, <F2>, <F3>, <F4>, <Enter>, <ESC>, arrow keys, etc. (as listed in
Table 3-1).
NOTE: Some of the navigation keys may differ from one screen to another.
Table 3-1 Descriptions of hot keys
AMI BIOS Setup Utility 23
Page 30
GOT107W-319 User’s Manual
3.2 Main Menu
Figure 3-1 Main menu
System Time/Date
Use this option to change the system time and date. Highlight System Time or System Date
using the up/ down/ left and right arrow keys (see Figure 3-1). Enter new values through the
keyboard. Press the <Tab> key or the arrow keys to move between fields. The date entered
must be in MM/DD/YY format. The time is entered in HH:MM:SS format.
24 AMI BIOS Setup Utility
Page 31
3.3 Advanced Menu
GOT107W-319 User’s Manual
Figure 3-2 Advanced menu
The Advanced menu allows users to set configurations of the CPU and other system devices.
Select any item on the left to go to the sub-menus (as shown in Figure 3-2).
► Serial Port Configuration
► Hardware Monitor
► Trusted Computing
► ACPI Settings
► CPU Configuration
► SATA Configuration
► USB Configuration
Simply highlight the item of choice, then press <Enter> to go to sub-menus for more specific
options.
AMI BIOS Setup Utility 25
Page 32
GOT107W-319 User’s Manual
3.3.1 Serial Port Configuration
► Serial Port 1 Configuration (COM1)
► Serial Port 2 Configuration (COM2)
Serial port
This option is used to enable or disable serial port COM1/COM2.
Device Setting
This item specifies the base I/O port address and Interrupt Request (IRQ) address of a serial
port.
Optimal setting for Port 1 is [3F8h/IRQ4].
Optimal setting for Port 2 is [2F8h/IRQ5].
COM 1 Port Type
This option is used to select COM Port Type: [RS-232] or [RS-422] or [RS-485].
This option is used to select COM Port Type: [RI] or [5V ] or [+12V]
Figure 3-4 ‘Serial Port Configuration’ -> ‘COM Port Type’
26 AMI BIOS Setup Utility
Page 33
GOT107W-319 User’s Manual
3.3.2 Hardware Monitor
Figure 3-5 shows a screen reflecting the ‘PC Health Status’ of the hardware in real time.
Figure 3-5 Entering ‘Hardware Monitor’
AMI BIOS Setup Utility 27
Page 34
GOT107W-319 User’s Manual
3.3.3 Trusted Computing
This screen is used to select options of the TPM2.0 Configuration, and then change the value
of the selected option. A description of the selected item appears on the right side of the
screen.
28 AMI BIOS Setup Utility
Page 35
GOT107W-319 User’s Manual
3.3.4 ACPI Settings
This screen is used to select options of the ACPI Configuration, and then change the value of
the selected option. A description of the selected item appears on the right side of the screen.
ACPI Sleep State
This item allows users to select the Advanced Configuration and Power Interface (ACPI) state
to be used for system suspension. There are two choices under this selection: [Suspend
Disable] or [S3 (Suspend to RAM)] (as shown in Figure 3-6).
Figure 3-6 Entering ‘ACPI Settings’
AMI BIOS Setup Utility 29
Page 36
GOT107W-319 User’s Manual
3.3.5 CPU Configuration
Figure 3-7 shows a page of CPU configuration with the item Intel Virtualization Technology
highlighted for [Enabled] or [Disabled].
Figure 3-7 Entering ‘CPU Configuration’
30 AMI BIOS Setup Utility
Page 37
GOT107W-319 User’s Manual
3.3.6 SATA Configuration
This screen allows users to select options for SATA Configuration, and then change the value
of the selected option (see Figure 3-8).
SATA Controller
Highlight this item to set up SATA Controller to be [Enable] or [Disable].
Figure 3-8 Entering ‘SATA Configuration’
AMI BIOS Setup Utility 31
Page 38
GOT107W-319 User’s Manual
3.3.7 USB Configuration
Please see Figure 3-9 to find out what items can be set up under the page of USB Configuration.
Figure 3-9 Entering ‘USB Configuration’
32 AMI BIOS Setup Utility
Page 39
GOT107W-319 User’s Manual
3.4 Chipset Menu
The Chipset menu gives memory information about the North Bridge and South Bridge (see
Figure 3-12).
Figure 3-12 Chipset menu
AMI BIOS Setup Utility 33
Page 40
GOT107W-319 User’s Manual
3.4.1 North Bridge
North Bridge memory information is shown in Figure 3-13.
Figure 3-13 Entering ‘North Bridge’
34 AMI BIOS Setup Utility
Page 41
3.4.2 South Bridge
South Bridge TXE information is shown in Figure 3-14.
Figure 3-14 Entering ‘South Bridge’
GOT107W-319 User’s Manual
AMI BIOS Setup Utility 35
Page 42
GOT107W-319 User’s Manual
3.5 Security Menu
You may set the administrator/user password for the system.
Figure 3-15 Security Menu
36 AMI BIOS Setup Utility
Page 43
GOT107W-319 User’s Manual
3.6 Boot Menu
The Boot menu allows users to change boot options of the system. Users can highlight any of
the items on the left frame of the screen to go to any particular sub menus (as shown in Figure
3-16).
Figure 3-16 Boot Menu
Setup Prompt Timeout
Enter a numeric value here as the length for timeout.
Bootup NumLock State
Use this item to select the power-on state for the NumLock. The default setting is [On].
Quiet Boot
Use this item to enable or disable the Quite Boot state. The default setting is [Disabled].
Launch UEFI PXE OpROM policy
Use this item to enable or disable the Pre-boot Execution Environment (PXE) under UEFI
mode. The default setting is [Disabled].
Boot Option Priorities
Use this item to specify the overall boot order among the available devices.
AMI BIOS Setup Utility 37
Page 44
GOT107W-319 User’s Manual
3.7 Save & Exit Menu
Figure 3-17 Save & Exit Menu
38 AMI BIOS Setup Utility
Page 45
GOT107W-319 User’s Manual
Touch Screen
Projected Capacitive Multi-touch
Touch Screen Controller
COF
Communications
USB interface
Resolution
4096 x 4096 resolution
Power Input
5V
Power Consumption
Active: <100mA / Idle Mode: 50mA
Input Method
Finger or Cap.Stylus
Calibration
Non-Calibration
Chapter 4
Drivers Installation
4.1 System
The GOT107W-319 supports Windows 10 pro and Windows 10 IoT Enterprise. To facilitate the
installation of the system driver, please carefully read the instructions in this chapter before
installation.
4.1.1 Windows 10
1. Insert the driver CD and select the files from step 1 to step 5.
2. Select all files and follow the installing procedure.
4.2 Touch Screen
The GOT107W-319 adopts a Projected Capacitive Multi-touch screen. The specification is
listed in Table 4-1 below. The touch driver will be installed automatically to enable the touch
panel’s two fingers touch functions based on the Windows 10 and Windows IoT Enterprise
support.
Table 4-1 Touch screen specification
Drivers Installation 39
Page 46
GOT107W-319 User’s Manual
This page is intentionally left blank.
40 Drivers Installation
Page 47
GOT107W-319 User’s Manual
Appendix A
Watchdog Timer & DIO
Programming
About Watchdog Timer
Software stability is a major issue in most applications. Some embedded systems are not
watched by humans for 24 hours. It is usually too slow to wait for someone to reboot when a
computer hangs. The system needs to be able to reset automatically when things go wrong.
The watchdog timer gives us that solution.
The watchdog timer is a counter that triggers a system reset when it counts down to zero from
a preset value. The software starts the counter with an initial value and must reset it
periodically. If the counter ever reaches zero which means the software has crashed, the
system will reboot.
How to Use Watchdog Timer
The I/O port base addresses of the watchdog timer are 2E (hex) and 2F (hex). The 2E (hex)
and 2F (hex) are address and data port respectively.
Assume that program A is put in a loop that must execute at least once every 10ms. Initialize
the watchdog timer with a value bigger than 10ms. If the software has no problems, the
watchdog timer will never expire because software will always restart the counter before it
reaches zero.
Watchdog Timer & DIO Programming 41
Page 48
GOT107W-319 User’s Manual
Begin
Enable and Initialize
Watchdog Timer
Program “A”
Disable Watchdog
Timer
Next
Next
Next
Next
Begin
Enable and Initialize
Watchdog Timer
Program “A”
Reset Watchdog
Timer
Next
Next
Next
Next
42 Watchdog Timer & DIO Programming
Page 49
WDT Sample Program
Enable WDT
1.Enable configuration:
-O 2E 87
-O 2E 87
2. Select Logic device:
-O 2E 07
-O 2F 07
3. WDT device enable:
-O 2E FA
-O 2F 01
4. Set base timer:
-O 2E F6
-O 2F 0A Set reset time (Ex.0A:10 Sec/Minute)
5. Set timer unit (bit[3]=0: Sec; bit[3]=1: Minute):
Enable watchdog time counting (bit5=1)
-O 2E F5
-O 2F 20 (Set timer unit to sec and enable counting)
GOT107W-319 User’s Manual
How to Use DIO Software Programming
Digital I/O Software Programming
I2C to GPIO PCA9535PW GPIO
I2C address: 0b01000100.
Watchdog Timer & DIO Programming 43
Page 50
GOT107W-319 User’s Manual
44 Watchdog Timer & DIO Programming
Page 51
GOT107W-319 User’s Manual
Watchdog Timer & DIO Programming 45
Loading...