AXIOMTEK FDK150-830-N, FDK150-830-R, FDK170-830-N, FDK170-830-R, FDK190-830-N User Manual
...
FDK Series
15” 17” 19” Flexible Display Panel PC
User’s Manual
ii
Disclaimers
This manual has been carefully checked and believed to contain
accurate information. AXIOMTEK Co., Ltd. assumes no responsibility
for any infringements of patents or any third party’s rights, and any
liability arising from such use.
AXIOMTEK does not warrant or assume any legal liability or
responsibility for the accuracy, completeness or usefulness of any
information in this document. AXIOMTEK does not make any
commitment to update the information in this manual.
AXIOMTEK reserves the right to change or revise this document
and/or product at any time without notice.
No part of this document may be reproduced, stored in a retrieval
system, or transmitted, in any form or by any means, electronic,
mechanical, photocopying, recording, or othe rw ise, witho ut the pri or
written permission of AXIOMTEK Co., Ltd.
©Copyright 2010 AXIOMTEK Co., Ltd.
All Rights Reserved
August 2010, Version A1
Printed in Taiwan
iii
Safety Approvals
CE Marking
FCC Class A
FCC Compliance
This equipment has been tested in compliance with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are meant to provide reasonable protection against harmful
interference in a residential installation. If not installed and used in
accordance with proper instructions, this equipment might generate or
radiate radio frequency energy and cause harmful interference to
radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following methods:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment to another outlet of a circuit that
doesn’t connect with the receiver.
4. Consult the dealer or an experienced radio/TV technician for
help.
Shielded interface cables must be used in order to comply with the
emission limits.
iv
Safety Precautions
Before getting started, please read the following important safety
precautions.
1. The FDK does not come equipped with an operating system.
An operating system must be loaded first before installing
any software into the computer.
2. Be sure to ground yourself to prevent static charge when
installing the internal components. Use a grounding wrist
strap and place all electronic components in any staticshielded devices. Most electronic components are sensitive
to static electrical charge.
3. Disconnect the power cord from the FDK before any
installation. Be sure both the system and external devices
are turned OFF. A sudden surge of power could ruin
sensitive components that the FDK must be properly
grounded.
4. The brightness of the flat panel display will be getting weaker
as a result of frequent usage. However, the operating period
varies depending on the application environment.
5. Turn OFF the system power before cleaning. Clean the
system using a cloth only. Do not spray any liquid cleaner
directly onto the screen. The FDK may come with or w/o a
touchscreen. Although the touchscreen is chemical resistant,
it is recommended that you spray the liquid cleaner on a
cloth first before wiping the screen. In case your system
comes without the touchscreen, you must follow the same
procedure and not spray any cleaner on the flat panel
directly.
6. Avoid using sharp objects to operate the touchscreen.
Scratches on the touchscreen may cause malfunction or
internal failure to the touchscreen.
7. The flat panel display is not susceptible to shock or vibration.
When assembling the FDK, mak e sure it is securely installed.
8. Do not open the system’s back cover. If opening the cover
for maintenance is a must, only a trained technician is
allowed to do so. Integrated circuits on c omputer boards are
sensitive to static electricity. To avoid damaging chips from
electrostatic discharge, observe the following precautions:
v
z Before handling a board or integrated circuit, touch an
unpainted portion of the system unit chassis for a few
seconds. This will help to discharge any static
electricity on your body.
z When handling boards and components, wear a wrist-
grounding strap, available from most electronic
component stores.
Trademarks Acknowledgments
AXIOMTEK is a trademark of AXIOMTEK Co., Ltd.
IBM, PC/AT, PS/2, VGA are trademarks of International
Business Machines Corporation.
Intel
®
and Atom™ are registered trademarks of Intel Corporation.
MS-DOS, Microsoft C and Quick BASIC are trademarks of Microsoft
Corporation.
VIA is a trademark of VIA Technologies, Inc.
SST is a trademark of Silicon Storage Technology, Inc.
UMC is a trademark of United Microelectronics Corporation.
Other brand names and trademarks are the properties and registered
brands of their respective owners.
–
vi
Table of Contents
Disclaimers ....................... .................................................. . ii
Safety Approvals ................................................................. iii
Safety Precautions.............................................................. iv
CHAPTER 1 INTRODUCTION ......................................... 1
1.1 General Description ............................................ 1
1.2 Specifications ............................. ......................... 2
1.2.1 Main CPU Board ......................................................... 2
1.2.2 I/O System .................................................................. 2
1.2.3 System Specification .................................................. 3
1.3 Product List ......................................................... 4
1.4 Dimensions ......................................................... 5
1.4 I/O Outlets ............................................... .......... 11
1.5 Packing List ...................................................... 12
CHAPTER 2 HARDWARE INSTALLATION .............. 13
2.1 Open and close back cover .............................. 13
2.2 CF card Installation ........................................... 17
2.2 Serial Ports Interface ........................................ 19
2.3 Ethernet ........................... ................................. 21
2.4 Openframe and VESA Mountings ..................... 22
2.4.1 Openframe Mounting ................................................ 22
2.4.2 VESA Mounting ......................................................... 23
2.5 HDD Installation ................................................ 24
2.6 DRAM Installation ............................................. 26
2.7 Wireless LAN Card Installation ......................... 28
CHAPTER 3 AMI BIOS SETUP UTILITY ..................... 32
3.1 Starting .......................... ................. .................. 32
3.2 Navigation Keys ................................................ 32
3.3 Main Menu ........................................................ 33
3.4 Advanced Menu ................................................ 34
3.5 PCI PnP Menu .................................................. 47
3.6 Boot Menu ........................................................ 50
3.7 Security Menu ................................................... 55
vii
3.8 Chipset Menu ....................................... ............. 57
3.9 Exit Menu .......................................................... 62
CHAPTER 4 DRIVERS INSTALLATION ..................... 64
4.1 System .............................................................. 64
4.2 Touch Screen ................................................... 65
4.2.1 Specification .............................................................. 65
4.2.2 Driver Installation- Windows XP ..................... .......... 65
4.3 Embedded O.S. ................................................ 68
4.3.1 Windows XP Embedded ........................................... 68
viii
MEMO
FDK User’s Manual
Introduction
1
CHAPTER 1
INTRODUCTION
This chapter contains general information and detailed specifications
of the FDK series. Chapter 1 includes the following sections:
General Description
Specification
Dimensions
I/O Outlets
Package List
1.1 General Description
The FDK series is an open frame touch panel computer, equipped
with a TFT LCD display and low power consumption Intel
○R
AtomTM
N270 1.6GHz processor with FSB 533MHz. The FDK series supports
Windows
®
7, Windows® XP, and Windows® XP embedded. The
panel computer is able to install a CompactFlash
™ card and provide
a Mini card slot for wireless module. This slim series is designed for
immediate integration and can be widely deployed in indoor kiosk,
HMI automation, and many more applications. Its slim ID can fits into
any space or encased in any chassis, this series comes with a front
panel open frame design, available currently in 15”, 17” and 19” LCD
sizes.
Other than offering above configuration advantages, this open frame
panel computer series also highlights an ultra slim profile and
compact footprint in thickness of 60mm for any space. Moreover, the
brightness adjustment knob located on the back cover makes
maintenance easier and faster. For WiFi & 3G connection, this slim
FDK series User’s Manual
Introduction
2
unit incorporates a Mini Card slot for expansion capability.
1.2 Specifications
1.2.1 Main CPU Board
z CPU
Intel
○R
AtomTM N270 1.6GHz processor with FSB 533MHz
onboard
z System Chipset
945GSE + ICH7M
z BIOS
America Megatrends BIOS
z System Memory
One 200-pin DDR2 SO-DIMM socket
Maximum memory up to 2GB
1.2.2 I/O System
z Standard I/O
Three RS-232 and one RS-232/422/485
Four USB 2.0
z Ethernet
One RTL81111b Gigabit Ethernet
z Audio
One Line-out
z Expansion
One Mini card
z Storage
One slot for CF card
One SATA
z Power connector
Phoenix power connector
FDK User’s Manual
Introduction
3
1.2.3 System Specification
z 15”(1024x768), 17”(1280x1024), or 19”(1280x1024) TFT
LCD
One VR for brightness control
z Touch (equip on FDK1x0-830-R models)
5-wired resistive touch
z Heat Dispensing Design
z Disk drive housing:
One 2.5” SATA drive
z Net Weight
3.84 Kgs (8.46 lb) (FDK150-830-R)
5.52 Kgs (12.16 lb) (FDK170-830-R)
5.82 Kgs (12.83 lb) (FDK190-830-R)
z Dimension (Main Body Size)
335mm x 261.5mm x 60mm (FDK150-830-N)
335mm x 261.5mm x 63.3mm (FDK150-830-R)
367mm x 304.5mm x 65mm (FDK170-830-N)
367mm x 304.5mm x 69.3mm (FDK170-830-R)
404.5mm x 332mm x 65mm (FDK190-830-N)
404.5mm x 332mm x 69.3mm (FDK190-830-R)
z Operation Temperature
0℃ to 50℃
z Relative Humidity
10% to 90% @ 40℃, Non-Condensing
z Power input
10~30VDC with phoenix power connector
NOTE All specifications and images are subject to change
without notice.
NOTE If the operation temperature is higher than 40℃, the
wide temperature DRAM is recommended to be used on
the device.
FDK series User’s Manual
Introduction
4
1.3 Product List
FDK series provides three sizes of LCD, 15”, 17”, and 19”. The
touch screen is optional. Please refer to the following table.
Product Name LCD Size Resolution Touch
FDK150-830-N
15”
1024 x 768 N
FDK150-830-R
15”
1024 x 768 Y
FDK170-830-N
17”
1280 x 1024 N
FDK170-830-R
17”
1280 x 1024 Y
FDK190-830-N
19”
1280 x 1024 N
FDK190-830-R
19”
1280 x 1024 Y
FDK User’s Manual
Introduction
5
1.4 Dimensions
FDK150-830-N without touch dimensions
FDK series User’s Manual
Introduction
6
FDK150-830-R with touch dimensions
FDK User’s Manual
Introduction
7
FDK170-830-N without touch dimensions
FDK series User’s Manual
Introduction
8
FDK170-830-R with touch dimensions
FDK User’s Manual
Introduction
9
FDK190-830-N without touch dimensions
FDK series User’s Manual
Introduction
10
FDK190-830-R with touch dimensions
FDK User’s Manual
Introduction
11
1.4 I/O Outlets
Please refer to the following illustration for I/O locations of the FDK.
No Function No Function
1 POWER SWITCH (ATX) 7 COM 2 (RS-232)
2 Power Input connector (phoenix type) 8 VGA
3 2 X USB 2.0 9 1X ETHERNET (RJ-45)
4 COM 3 (RS-232) 10 2 X USB 2.0
5 COM 4 (RS-232) 11 AUDIO (LINE-OUT)
6 COM 1 (RS-232/422/485)
FDK series User’s Manual
Introduction
12
1.5 Packing List
When you receive the FDK, the bundled package should contain the
following items:
z FDK unit x 1
z Driver CD x1
z SATA cable x 1
z SATA power cable x 1
z Phoenix connector x 1
If you can not find the package or any items are missing, please
contact AXIOMTEK distributors immediately.
FDK series User’s Manual
Hardware Installation
13
CHAPTER 2
HARDWARE INSTALLATION
The FDK series provides rich I/O ports and flexible expansions for
you to meet different demand, for example, CF card. The chapter will
show you how to install the hardware. It includes:
CompactFlash™ Card
Serial Port
Ethernet
Mounting Method
Hard disk
DRAM
Wireless LAN Card
2.1 Open and close back cover
This section tells users how to open and close the back c over. Ple ase
follow the steps below.
Step 1 Unscrew eleven screws on the back cover. Please
refer the photo of top side, right side and le ft side.
FDK series User’s Manual
Hardware Installation
14
Step 2 When users open the back cover, there is a cable
connecting between a fan and the motherboard.
FDK series User’s Manual
Hardware Installation
15
Step 3 Remove the connector first before remove the back
cover totally.
Step 4 After removing the back cover, users can see the
inside of the unit.
Loading...