AXIOMTEK eBOX800-511-FL- DC-7300U, eBOX800-511-FL- DC-3965U User Manual

eBOX800-511-FL Series

Embedded System

User’s Manual

ii

Disclaimers

This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third
party’s rights, or any liability arising from such uses.

Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make any
commitment to update any information in this manual.

Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.

No part of this document may be reproduced, stored in a retrieval system, or transmitted in
any forms or by any means, electronic, mechanical, photocopying, recording, among others,
without prior written permissions of Axiomtek Co., Ltd.

Copyright 2018 Axiomtek Co., Ltd.
All Rights Reserved
Nov 2018, Version A2
Printed in Taiwan

iii

Safety Precautions

Before getting started, please read the following important safety precautions.

1. The eBOX800-511-FL does not come with an operating system which must be loaded
first before installation of any software into the computer.

2. Be sure to ground yourself to prevent static charge when installing any internal
components. Use a wrist grounding strap and place all electronic components in any
static-shielded devices. Most electronic components are sensitive to static electrical
charge.

3. Disconnect the power cord from the eBOX800-511-FL prior to making any installation.
Be sure both the system and all external devices are turned OFF. Sudden surge of
power could ruin sensitive components. Make sure the eBOX800-511-FL is properly
grounded.

4. Make sure the voltage of the power source is correct before connecting it to any power
outlet.

5. Turn off system power before cleaning. Clean the system using a cloth only. Do not
spray any liquid cleaner directly onto the screen.

6. Do not leave equipment in an uncontrolled environment where the storage temperature
is below -40℃ or above 80℃ as it may damage the equipment.

7. Do not open the system’s back cover. If opening the cover for maintenance is a must,
only a trained technician is allowed to do so. Integrated circuits on computer boards are
sensitive to static electricity. To avoid damaging chips from electrostatic discharge,
observe the following precautions:

 Before handling a board or integrated circuit, touch an unpainted portion of the

system unit chassis for a few seconds. This will help discharge any static electricity on
human body.

 When handling boards and components, wear a wrist grounding strap available from

most electronic component stores.

iv

Classifications

1. Degree of production against electric shock: not classified

2. Degree of protection against ingress of water: IP67

3. Equipment not suitable for use in the presence of a flammable anesthetic mixture with air,

oxygen or nitrous oxide.

4. Mode of operation: Continuous

v

General Cleaning Tips

Please keep the following precautions in mind while understanding the details fully before and
during any cleaning of the computer and any components within.

A piece of dry cloth is ideal to clean the device.

1. Be cautious of any tiny removable components when using a vacuum cleaner to absorb
dirt on the floor.

2. Turn the system off before clean up the computer or any components within.

3. Avoid dropping any components inside the computer or getting circuit board damp or wet.

4. For cleaning, be cautious of all kinds of cleaning solvents or chemicals which may cause
allergy to certain individuals.

5. Keep foods, drinks or cigarettes away from the computer.

Cleaning Tools:

Although many companies have created products to help improve the process of cleaning
computer and peripherals, users can also use house hold items accordingly for cleaning.
Listed below are items available for cleaning computer or computer peripherals.

Pay special attention to components requiring designated products for cleaning as
mentioned below.

 Cloth: A piece of cloth is the best tool to use when rubbing up a component. Although

paper towels or tissues can be used on most hardware as well, it is recommended to use
a piece of cloth.

 Water or rubbing alcohol: A piece of cloth may be somewhat moistened with water or

rubbing alcohol before being rubbed on the computer. Unknown solvents may be harmful
to plastic parts.

 Absorb dust, dirt, hair, cigarette and other particles outside of a computer can be one of

the best methods of cleaning a computer. Over time these items may restrict the airflow
in a computer and cause circuitry to corrode.

 Cotton swabs: Cotton swaps moistened with rubbing alcohol or water are applicable to

reach areas in keyboard, mouse and other areas.

 Foam swabs: If possible, it is better to use lint free swabs such as foam swabs.

.

【Note】: It is strongly recommended that customer should shut down the system before

start to clean any single components.

Please follow the steps below:

1. Close all application programs;

2. Close operating software;

3. Turn off power switch;

4. Remove all devices;

5. Pull out power cable.

vi

Scrap Computer Recycling

Please inform the nearest Axiomtek distributor as soon as possible for suitable solutions in
case computers require maintenance or repair; or for recycling in case computers are out of
order.

Trademarks Acknowledgments

Axiomtek is a trademark of Axiomtek Co., Ltd.
IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation.
Intel® and Pentium® are registered trademarks of Intel Corporation.
MS-DOS, Microsoft C and QuickBasic are trademarks of Microsoft Corporation.
Windows 10, Windows 8.1, Windows 8, Windows 7, Windows XPE, Windows XP, Windows
CE embedded, Linux, MS-DOS, Microsoft C and Other brand names and trademarks are
the properties and registered brands of their respective owners.

vii

Table of Contents

Disclaimers ............................................................................................................. ii

Safety Precautions ................................................................................................ iii

Classifications ....................................................................................................... iv

General Cleaning Tips ........................................................................................... v

Scrap Computer Recycling ................................................................................... vi

SECTION 1 INTRODUCTION ........................................................................ 1

1.1 General Descriptions ......................................................................... 1

1.2 System Specifications ....................................................................... 3

1.2.1 CPU ................................................................................................................... 3

1.2.2 I/O System ........................................................................................................ 3

1.2.3 System Specifications ..................................................................................... 4

1.2.4 Driver CD Contents .......................................................................................... 4

1.3 Dimensions ........................................................................................ 5

1.3.1 System Dimensions ......................................................................................... 5

1.3.2 Wall-mount Bracket Dimensions ................................................................... 6

1.3.3 VESA-mount Bracket Dimensions ................................................................. 7

1.4 I/O Outlets .......................................................................................... 8

1.5 Packing List ........................................................................................ 9

1.6 Model List ........................................................................................... 9

SECTION 2 HARDWARE INSTALLATION .................................................. 11

2.1 Installation of 2.5" SATA Device ..................................................... 12

2.2 Installation of SO-DIMM ................................................................... 14

2.3 Installation of WI-FI Mini PCIe Module (half-size) .......................... 16

2.4 Installation of 3G/4G Mini PCIe Module (full-size) ......................... 17

SECTION 3 JUMPER & CONNECTOR SETTINGS .................................... 19

3.1 Locations of Jumpers & Connectors ............................................. 19

3.2 Summary of Jumper Settings ........................................................ 21

3.2.1 Restore BIOS Optimal Defaults (JP2) .......................................................... 22

3.2.2 Auto Power On (JP3) ..................................................................................... 22

3.3 Connectors ....................................................................................... 23

3.3.1 Serial Port (M12 A-Code 8 pos Male) ........................................................... 24

3.3.2 Ethernet Port (M12 X-Code 8 pos Female) .................................................. 25

3.3.3 USB Port (M12 A-Code 8 pos Male) ............................................................. 25

3.3.4 DC Power Jack Connector (M12 A-Code 5 pos Male) ................................ 25

3.3.5 VGA Connector (M12 A-Code 12 pos Male)................................................. 26

3.3.6 Half-size PCI-Express Mini Card Connector (SCN3) .................................. 27

3.3.7 Full-Size PCI-Express Mini Card Connector (SCN1) .................................. 28

3.3.8 SATA Power Connector (CN6) ...................................................................... 29

3.3.9 CMOS Battery Connector (CN8) ................................................................... 29

3.3.10 Ethernet Connector (CN15) ......................................................................... 29

3.3.11 Power Connector (CN14) ............................................................................. 30

3.4 Waterproof Cables ........................................................................... 30

viii

SECTION 4 BIOS SETUP UTILITY .............................................................. 33

4.1 Starting ............................................................................................. 33

4.2 Navigation Keys ............................................................................... 33

4.3 Main Menu ........................................................................................ 34

4.4 Advanced Menu ................................................................................ 35

4.5 Chipset Menu ................................................................................... 47

4.6 Boot Menu ........................................................................................ 53

4.7 Save & Exit Menu ............................................................................. 54

APPENDIX A WATCHDOG TIMER .............................................................. 57

A.1 About Watchdog Timer .................................................................... 57

A.2 How to Use Watchdog Timer .......................................................... 57

APPENDIX B iAMT SETTINGS ................................................................... 59

B.1 Entering MEBx ................................................................................ 59

B.2 Set and Change Password ............................................................. 59

B.3 iAMT Configuration ................................ ......................................... 61

B.4 iAMT Web Console .......................................................................... 69

APPENDIX C BIOS Flash Utility ................................................................. 71

APPENDIX D IO BOARD ............................................................................. 75

eBOX800-511-FL-FL Series user’s Manual

Introduction

1

SECTION 1

INTRODUCTION

This section contains general information and detailed specifications of the
eBOX800-511-FL.Section 1 consist of the following sub-sections:

 General Descriptions
 System Specifications
 Dimensions
 I/O Outlets
 Packing List
 Model List

1.1 General Descriptions

The eBOX800-511-FL comes with Intel

®

Core™ i5-7300U/Intel

®

Celeron

®

3965U processor

(Kabylake SoC), utilizing a full IP67-rated aluminum die-casting and heavy-duty steel case.
It is supports Windows 10, Windows 10 IoT and Linux.

The fanless and streamlined enclosure ensures excellent heat dissipation. In addition, this
reliable box pc is designed to operate under wide temperature ranges from -30°C to 60°C,
under wide range of DC power input from 9 to 36 VDC and under harsh/outdoor applications
with M12 lockable connectors.

Features

1. Fanless with IP67-rated enclosure design

2. Intel

®

Core™ i5-7300U 2.6 GHz/ Intel

®

Celeron

®

3965U 2.2 GHz SoC onboard

3. Four antenna openings with waterproof design for WLAN & WWAN usage

4. Wide range of DC power input supported from 9 to 36 VDC

5. Flexible I/O for customized designs and mission-critical projects

eBOX800-511-FL-FL Series user’s Manual

Introduction

2

Reliable and Stable Design

Powered by onboard quad-core processor, the eBOX800-511-FL is equipped with

M12 lockable connectors while supporting wall-mount/vest-mount kit for outdoor
applications.

Flexible Connectivity

The eBOX800-511-FL features one Gigabit Ethernet ports and two USB 2.0 ports.
Additionally, it also supports two RS-232/422/485 serial interfaces.

Embedded O.S. Supported

The eBOX800-511-FL supports not only Windows 10 but also embedded OS, such as
Windows 10 Embedded and Linux.

Various Storage Supported

In terms of storage, the eBOX800-511-FL supports one 2.5" SATA storage drive bay and
one mSATA device.

eBOX800-511-FL-FL Series user’s Manual

Introduction

3

1.2 System Specifications

1.2.1 CPU

CPU

 Intel

®

Core™ i5-7300U 2.6 GHz

 Intel

®

Celeron® 3965U 2.2 GHz

Chipset

 SoC integrated

BIOS

 American Megatrends Inc. UEFI (Unified Extensible Firmware Interface) BIOS

System Memory

 One 260-pin unbuffered DDR4 2133MHz SO-DIMM socket, up to 16 GB at the

maximum

1.2.2 I/O System

Display

 1 x VGA connector (M12 A-Code 12 pos Male)
 Resolution max up to 1600 x 1200 x 24

Ethernet

 1 x 10/100/1000 Ethernet ports (M12 X-Code 8 pos Female)

USB Ports

 1 x USB connector to 2 x USB 2.0 ports (M12 A-Code 8 pos Male)

Serial Ports

 2 x RS-232/422/485 (COM1/COM2)(M12 A-Code 8 pos Male)

Mini PCIe Interface

 1 x full-size PCI Express Mini Card Slots with mSATA supported
 1 x half-size PCI Express Mini Card Slots

Storage

 1 x 2.5" SATA HDD/SSD drive bay
 1 x mSATA (enabled in BIOS setting)

Indicator

 1 x Green LED as indicator for system power on

Switch

 1 x ATX power switch with indicator
 1 x Power input (M12 A-Code 5 pos Male)

Antenna

 4 x Antenna opening N Jack type with waterproof design

eBOX800-511-FL-FL Series user’s Manual

Introduction

4

1.2.3 System Specifications

Watchdog Timer

 1~255 seconds or minutes; up to 255 levels.

Power Supply

 9~36 VDC input

Operation Temperature

 -30℃ ~ 60℃ (-22 ºF ~ 140ºF), with W.T. SSD & Memory)

Storage Temperature

 -40℃ ~ 80℃ (-40 ºF ~ 176ºF)

Humidity

 10% ~ 90% (non-condensation)

Package Vibration Endurance

 2.25Grm (5-500Hz, X, Y, Z directions)

Weight

 4.31 kg (9.5 lb) without package
 5.1 kg (11.24 lb) with package

Dimension

 210 mm (8.27") (W) x 366.83 mm (14.44") (D) x 83 mm (3.27”) (H)

1.2.4 Driver CD Contents

 Ethernet
 Chipset
 Graphic
 Intel Rapid Storage Technology
 Audio
 Intel

®

TXE Firmware

 User Manual
 Quick Manual

【Note】: All specifications and images are subject to change without notice.

eBOX800-511-FL-FL Series user’s Manual

Introduction

5

1.3 Dimensions

The following diagrams show dimensions and outlines of the eBOX800-511-FL.

1.3.1 System Dimensions

eBOX800-511-FL-FL Series user’s Manual

Introduction

6

1.3.2 Wall-mount Bracket Dimensions

eBOX800-511-FL-FL Series user’s Manual

Introduction

7

1.3.3 VESA-mount Bracket Dimensions

eBOX800-511-FL-FL Series user’s Manual

Introduction

8

1.4 I/O Outlets

The following figures show I/O outlets on front of the eBOX800-511-FL.

Top View

Bottom View

eBOX800-511-FL-FL Series user’s Manual

Introduction

9

1.5 Packing List

The eBOX800-511-FL comes with the following bundle package:

 eBOX800-511-FL System Unit x 1
 Quick Installation Guide x 1
 DVD x 1 (For Driver and Manual)
 waterproof PWR cable (L:1m) x 1
 waterproof VGA cable (L:1.8m) x 1
 waterproof USB 2.0 cable (L:1.8m) x 1
 HDD mylar x 1
 HDD screws x 2
 HDD poron x 1

1.6 Model List

eBOX800-511-FL- DC-7300U

Rugged IP67-rated fanless embedded system with Intel

®

Core™ i5-7300U 2.6 GHz, VGA, 1 GbE LANs, 2 USBs, 2
COMs and 9~36VDC power input

eBOX800-511-FL- DC-3965U

Rugged IP67-rated fanless embedded system with Intel

®

Celeron

®

3965U 2.2 GHz, VGA, 1 GbE LANs, 2 USBs, 2

COMs and 9~36VDC power input

Please contact Axiomtek’s distributors immediately in case any abovementioned items are
missing.

eBOX800-511-FL-FL Series user’s Manual

Introduction

10

This page is intentionally left blank.

eBOX800-511-FL-FL Series user’s Manual

Hardware Installation

11

SECTION 2

HARDWARE INSTALLATION

The eBOX800-511-FL is convenient for various hardware configurations, such as DRAM,
HDD (Hard Disk Drive), SSD (Solid State Drive) and PCI Express Mini card modules. Section
2 contains guidelines for hardware installation.

【Note】:

Waterproof capability may be affected if a system is dissembled; under such
circumstances Axiomtek shall not be liable for any quality deterioration.

【Note】: Please refer to tightening torque below for all system screws:
 HEX socket set screw: 7.5 kgf

HEX KEY specifications are shown below

 N jack connector: 10 kgf

eBOX800-511-FL-FL Series user’s Manual

Hardware Installation

12

2.1 Installation of 2.5" SATA Device

Step 1 Turn off the system and unplug the power cord.
Step 2 Turn the system upside down to locate screws at the bottom and then

loosen all screws.

Step 3 Remove the bottom cover.

Note: For 7"mm HDD/SSD, please add a HDD poron before install the

HDD/SSD.

Step 4 Locate SSD/HDD within the red line as marked.

Please notice the direction of connector for HDD.

eBOX800-511-FL-FL Series user’s Manual

Hardware Installation

13

Step 5 Before install an SSD/HDD, please place the mylar on top of the

SSD/HDD and fasten two screws.

Step 6 Install the SSD/HDD into the HDD drive bay and push the poron down to

ensure the complete insertion of SSD/HDD.

eBOX800-511-FL-FL Series user’s Manual

Hardware Installation

14

2.2 Installation of SO-DIMM

Step 1 Turn off the system and unplug the power cord.
Step 2 Six screws on the bottom heatsink are used to fasten the heatsink to

the chassis.

Step 3 Loosen the thumb screws to remove the metal plate then a SO -DIMM

socket on main board is visible.

eBOX800-511-FL-FL Series user’s Manual

Hardware Installation

15

Step 4 Locate the memory module, insert a gold colored contact into the

socket and push the module two end latches till locked.

Step 5 Replace the metal plate, fasten the thumb screws, then put the bottom

cover and fasten six screws back onto the system.

【Note】: Make sure all screws are fastened.

eBOX800-511-FL-FL Series user’s Manual

Hardware Installation

16

2.3 Installation of WI-FI Mini PCIe Module (half-size)

Step 1 Turn off the system and unplug the power cord.
Step 2 Turn the system upside down to locate screws at the bottom, and then

loosen all screws.

Step 3 Remove the metal plate by loosening the thumb screw, identify the WI-

FI, and then insert a WI-FI module.

Step 4 Connect RF Cable to I-PEX4 connector of WI-FI module and install

Antenna 1 and Antenna 2.

eBOX800-511-FL-FL Series user’s Manual

Hardware Installation

17

2.4 Installation of 3G/4G Mini PCIe Module (full-size)

Step 1 Turn off the system and unplug the power cord.
Step 2 Turn the system upside down to locate screws at the bottom, and then

loosen all screws.

Step 3 Remove the metal plate by loosening the thumb screws, identify the

socket， and then insert a 3G/4G module.

Note: eBOX800-511 doesn’t have SIM slot, please use 3G/4G module

with SIM on holder.

Note: Due to the full size PCIe mini card slot supports mSATA or PCIe

mini card, please choose either one to install, and refer to Section 4.4
for BIOS setting.

eBOX800-511-FL-FL Series user’s Manual

Hardware Installation

18

Step 4 Connect RF cable to I-PEX4 connector of 3G/4G Module and install

Antenna 3 and Antenna 4.

eBOX800-511-FL-FL Series user’s Manual

Jumper & Connector Settings

19

SECTION 3

JUMPER & CONNECTOR SETTINGS

Proper jumper settings configure the eBOX800-511-FL to meet various application needs.
Hereby all jumpers settings along with their default settings are listed for devices onboard.

3.1 Locations of Jumpers & Connectors

PICO511 Top View

eBOX800-511-FL-FL Series user’s Manual

Jumper & Connector Settings

20

PICO511 Bottom View

【 Note】 : It is strongly recommended that any unmentioned jumper settings

should not be modified without instructions by Axiomtek FAEs. Any
modifications without instructions might cause system failure.

eBOX800-511-FL-FL Series user’s Manual

Jumper & Connector Settings

21

3.2 Summary of Jumper Settings

Proper jumper settings configure the eBOX800-511-FL to meet various application purposes.
A table of all jumpers and their default settings is listed below.

PICO511

Jumpers

Descriptions

Settings

JP2

Restore BIOS Optimal Defaults
Default: Normal Operation

1-2 Close

JP3

Auto Power On
Default: Enable

2-3 Close

【Note】: How to setup Jumpers

That a cap on a jumper is to “close” the jumper, whereas that offs a jumper is to “open” the
jumper.

[Open] [Closed] [Pin1-2 Closed]

eBOX800-511-FL-FL Series user’s Manual

Jumper & Connector Settings

22

3.2.1 Restore BIOS Optimal Defaults (JP2)

Put jumper clip to pin 2-3 for a few seconds then move it back to pin 1-2. Doing this procedure
can restore BIOS optimal defaults.

3.2.2 Auto Power On (JP3)

If JP3 is enabled for power input, the system will be automatically power on without pressing
soft power button. If JP3 is disabled for power input, it is necessary to manually press soft
power button to power on the system.

Function

Setting

Normal (Default)

1-2 close

Restore BIOS optimal defaults

2-3 close

Function

Setting

Disable auto power on

1-2 close

Enable auto power on (Default)

2-3 close

eBOX800-511-FL-FL Series user’s Manual

Jumper & Connector Settings

23

3.3 Connectors

Please refer to pin assignments below :

External Connectors

Sections

Serial Port

3.3.1

Ethernet Port

3.3.2

USB Port

3.3.3

DC Power Jack Connector

3.3.4

VGA Connector

3.3.5

Internal Connectors

Sections

Half-size PCI-Express Mini Card (on PICO511)

3.3.6

Full-size PCI-Express Mini Card or mSATA
Connector (on PICO511)

3.3.7
SATA Power Connector (CN6) (on PICO511)

3.3.8

CMOS connector (CN8) (on PICO511)

3.3.9

Ethernet connector (CN15)

3.3.10

Power connector (CN14)

3.3.11

eBOX800-511-FL-FL Series user’s Manual

Jumper & Connector Settings

24

3.3.1 Serial Port (M12 A-Code 8 pos Male)

The following table shows pin assignments of this connector:

【Note】:Each port + 5V maximu m: 2A, +12V maxi mum: 1A .

Warning:
According to IP67 warrantee, please indicate specific COM1 settings at the time of placing

an order; don’t disassemble the system without authorization.
When receiving information via RS-422/485, if there appear some wrong codes,

please check whether RS-422/485 is connected to GND at both ends. The standard
method of RS-422/485 is to connect GND at both ends and make sure that receiver
and transmitter have the common ground.

Pins

RS-232

RS-422

RS-485

1

DCD

TX-

Data-

2

RXD

TX+

Data+

3

TXD

RX+

No use

4

DTR

RX-

No use

GND

GND

GND

5

DSR

No use

No use

6

RTS

No use

No use

7

CTS

No use

No use

8

RI

No use

No use

eBOX800-511-FL-FL Series user’s Manual

Jumper & Connector Settings

25

3.3.2 Ethernet Port (M12 X-Code 8 pos Female)

Connectable via a M12 X-CODE LAN connector, the eBOX800-511-FL may be equipped with
a high performance Plug and Play Ethernet interface which is fully compliant with IEEE 802.3
standard.

Please refer to detailed pin assignment listed below:

3.3.3 USB Port (M12 A-Code 8 pos Male)

The USB is a Universal Serial Bus (compliant with USB 2.0 (480 Mbps)) connector on the rear
I/O. It is commonly used for installing USB peripherals such as keyboard, mouse, scanner, etc.

3.3.4 DC Power Jack Connector (M12 A-Code 5 pos Male)

Pins

Signals

Pins

Signals

L1

MDI0P

L5

MDI3P

L2

MDI0N

L6

MDI3N

L3

MDI1P

L7

MDI2N

L4

MDI1N

L8

MDI2P

Pins

Signals

Pins

Signals

1

USB VCC (+5V level)

5

USB VCC (+5V level)

2

USB #0_D-

6

USB #1_D-

3

USB #0_D+

7

USB #1_D+

4

GND

8

GND

Pins

Signals

1

9~36V

2

9~36V

3

GND

4

GND

5

Earth Ground

eBOX800-511-FL-FL Series user’s Manual

Jumper & Connector Settings

26

3.3.5 VGA Connector (M12 A-Code 12 pos Male)

Pins

Signals

Pins

Signals

1

Red

7

Vertical Sync

2

Green

8

DDC CLK

3

Blue

9

VCC

4

DDC DATA

10

GND

5

Horizontal Sync

11

GND

6

DETECT

12

GND

eBOX800-511-FL-FL Series user’s Manual

Jumper & Connector Settings

27

3.3.6 Half-size PCI-Express Mini Card Connector (SCN3)

This is a half-size PCI-Express Mini Card connector on the bottom side complying with PCI­Express Mini Card Spec. V1.2. It supports either PCI-Express or USB 2.0.

Pins

Signals

Pins

Signals

1

WAKE#

2

+3.3VSB

3

No use

4

GND

5

No use

6

+1.5V

7

CLKREQ#

8

No use

9

GND

10

No use

11

REFCLK-

12

No use

13

REFCLK+

14

No use

15

GND

16

No use

17

No use

18

GND

19

No use

20

W_DISABLE#

21

GND

22

PERST#

23

PE_RXN

24

+3.3VSB

25

PE_RXP

26

GND

27

GND

28

+1.5V

29

GND

30

SMB_CLK

31

PE_TXN

32

SMB_DATA

33

PE_TXP

34

GND

35

GND

36

USB_D4-

37

GND

38

USB_D4+

39

+3.3VSB

40

GND

41

+3.3VSB

42

No use

43

GND

44

No use

45

No use

46

No use

47

No use

48

+1.5V

49

No use

50

GND

51

No use

52

+3.3VSB

eBOX800-511-FL-FL Series user’s Manual

Jumper & Connector Settings

28

3.3.7 Full-Size PCI-Express Mini Card Connector (SCN1)

This is a full-size PCI-Express Mini Card connector on the bottom side complying with PCI­Express Mini Card Spec. V1.2. It supports either PCI-Express, USB 2.0 or SATA (mSATA).
To enable or disable mSATA support, please refer to BIOS setting in section 4.4.

Pins

Signals

Pins

Signals

1

WAKE#

2

+3.3VSB

3

No use

4

GND

5

No use

6

+1.5V

7

CLKREQ#

8

No use

9

GND

10

No use

11

REFCLK-

12

No use

13

REFCLK+

14

No use

15

GND

16

No use

17

No use

18

GND

19

No use

20

W_DISABLE#

21

GND

22

PERST#

23

PE_RXN/
SATA_RXP

24

+3.3VSB

25

PE_RXP/
SATA_RXN

26

GND
27

GND

28

+1.5V

29

GND

30

SMB_CLK

31

PE_TXN/
SATA_TXN

32

SMB_DATA

33

PE_TXP/
SATA_TXP

34

GND
35

GND

36

USB_D4-

37

GND

38

USB_D4+

39

+3.3VSB

40

GND

41

+3.3VSB

42

No use

43

GND

44

No use

45

No use

46

No use

47

No use

48

+1.5V

49

No use

50

GND

51

No use

52

+3.3VSB

eBOX800-511-FL-FL Series user’s Manual

Jumper & Connector Settings

29

3.3.8 SATA Power Connector (CN6)

The CN6 is a 4-pin (pitch=2.0mm) wafer connector, which is compliant with JST B4B-PH-K-S,
for SATA power interface.

3.3.9 CMOS Battery Connector (CN8)

This connector is for CMOS battery interface.

3.3.10 Ethernet Connector (CN15)

This is a JST BM16B-SRSS-TB 15-pin wafer connector for Ethernet interface. Gently connect
CN15 to AX93287 I/O board’s CN1.

1 15

Pins

Signals

1

+5V 2 GND

3

GND

4

+12V

Pins

Signals

1

+3.3V

2

GND

Pins

Signals

1

1000 LAN LED

2

100 LAN LED

3

GND

4

MDI3-

5

MDI3+

6

MDI1-

7

MDI2-

8

MDI2+

9

MDI1+

10

MDI0-

11

MDI0+

12

GND

13

LAN_VDD33

14

LAN_LINK_ACT

15

GND

1

eBOX800-511-FL-FL Series user’s Manual

Jumper & Connector Settings

30

3.3.11 Power Connector (CN14)

The CN14 is a 4-pin (pitch=2.5mm) wafer connector in right angle for DC +12V input. Gently
connect CN14 to AX98251 power board’s CN1.

3.4 Waterproof Cables

The eBOX800-511-FL series uses specific M12 connector for waterproof as enclosed in the
accessory box; included in the box are also VGA, USB and Power cables. Please refer to
pictures below for cables pin definitions.

Power Cable

Pins

Signals

V+

9~36VDC power input

Earth Ground

GND

GND

GND

GND

Pins

Signals

1

+12V

2

+12V

3

GND

4

GND

eBOX800-511-FL-FL Series user’s Manual

Jumper & Connector Settings

31

USB Cable

With two extended USB ports, the USB cable is combined with M12 connectors for waterproof.

VGA Cable

eBOX800-511-FL-FL Series user’s Manual

Jumper & Connector Settings

32

This page is intentionally left blank.

eBOX800-511-FL-FL Series user’s Manual

BIOS Setup Utility

33

SECTION 4

BIOS SETUP UTILITY

This section provides users with detailed descriptions in terms of how to set up basic system
configurations through the BIOS setup utility.

4.1 Starting

To enter the setup screens, follow the steps below:

1. Turn on the computer and press the <Del> key immediately.

2. After press the <Del> key, the main BIOS setup menu displays. Users can access to

other setup screens, such as the Advanced and Chipset menus, from the main BIOS
setup menu.

It is strongly recommended that users should avoid changing the chipset’s defaults. Both AMI
and system manufacturer have carefully set up these defaults that provide the best
performance and reliability.

4.2 Navigation Keys

The BIOS setup/utility uses a key-based navigation system called hot keys. Most of the BIOS
setup utility hot keys can be used at any time during the setup navigation process. These keys
include <F1>, <F2>, <Enter>, <ESC>, <Arrow> keys, and so on.

【 Note】: Some of the navigation keys differ from one screen to another.

Hot Keys

Descriptions

 Left/Right

The Left and Right <Arrow> keys allow users to select a setup screen.

 Up/Down

The Up and Down <Arrow> keys allow users to select a setup screen or
sub-screen.

+ Plus/Minus

The Plus and Minus <Arrow> keys allow users to change the field value of a
particular setup item.

Tab

The <Tab> key allows users to select setup fields.

F1

The <F1> key allows users to display the General Help screen.

F2

The <F2> key allows users to Load Previous Values.

F3

The <F3> key allows users to Load Optimized Defaults.

F4

The <F4> key allows users to save any changes they made and exit the
Setup. Press the <F4> key to save any changes.

Esc

The <Esc> key allows users to discard any changes they made and exit the
Setup. Press the <Esc> key to exit the setup without saving any changes.

Enter

The <Enter> key allows users to display or change the setup option listed
for a particular setup item. The <Enter> key can also allow users to display
the setup sub- screens.

eBOX800-511-FL-FL Series user’s Manual

BIOS Setup Utility

34

4.3 Main Menu

The Main Menu screen is the first screen users see when entering the setup utility. Users can
always return to the Main setup screen by selecting the Main tab. System Time/Date can be
set up as described below. The Main BIOS setup screen is also shown below.

BIOS Information

Display the auto-detected BIOS information.

System Language

Choose the system default language.

System Date/Time

Use this option to change the system time and date. Highlight System Time or System Date
using the <Arrow> keys. Enter new values through the keyboard. Press the <Tab> key or the
<Arrow> keys to move between fields. The date must be entered in MM/DD/YY format. The
time is entered in HH:MM:SS format.

Access Level

Display the access level of current user.

eBOX800-511-FL-FL Series user’s Manual

BIOS Setup Utility

35

4.4 Advanced Menu

The Advanced menu also allows users to set configuration of the CPU and other system
devices. Users can select any items in the left frame of the screen to go to sub menus:

► Hardware Monitor
► Utility Configuration
► ACPI Settings
► CPU Configuration
► SATA Configuration
► PCH-FW Configuration
► AMT Configuration
► USB Configuration
► Device Configuration

For items marked with “”, please press <Enter> for more options.

eBOX800-511-FL-FL Series user’s Manual

BIOS Setup Utility

36

Hardware Monitor
Use this screen to select options for the ACPI configuration, and change the value of the

selected option. A description of the selected item appears on the right side of the screen.

This screen displays the temperature of system and CPU, system voltages (VBAT, +3.3V,
+3.3_SBY and +5V).

eBOX800-511-FL-FL Series user’s Manual

BIOS Setup Utility

37

Utility Configuration

BIOS Flash Utility

BIOS flash utility configuration. For more detailed information, please refer to Appendix D.

eBOX800-511-FL-FL Series user’s Manual

BIOS Setup Utility

38

ACPI Settings

ACPI Sleep State

The setting is S3 (Suspend to RAM); this option selects ACPI sleep state the system will enter
when suspend button is pressed.

eBOX800-511-FL-FL Series user’s Manual

BIOS Setup Utility

39

CPU Configurations

This screen shows the CPU Configuration and you can change the value of the selected
option.

Intel (VMX) Virtualization Technology

Enable or disable Intel Virtualization Technology. When enabled, a VMM (Virtual Machine
Mode) can utilize the additional hardware capabilities. It allows a platform to run multiple
operating systems and applications independently, hence enabling a computer system to work
as several virtual systems.

eBOX800-511-FL-FL Series user’s Manual

BIOS Setup Utility

40

SATA Configuration

In the SATA Configuration menu, you can see the current installed hardware in the SATA
ports. During system boot up, the BIOS automatically detects the presence of SATA devices.

SATA Mode Selection

The SATA mode is set to AHCI.

mSATA

Enable or disable mSATA feature.

eBOX800-511-FL-FL Series user’s Manual

BIOS Setup Utility

41

PCH-HW

AMT Configuration
Use this screen to configure AMT parameters.

eBOX800-511-FL-FL Series user’s Manual

BIOS Setup Utility

42

AMT BIOS Features

Enable or disable AMT (Active Management Technology) BIOS features. The default is
Enabled. After enabling, please refer to Appendix C for iAMT settings.

USB Configuration

USB Devices

Display all detected USB devices.

eBOX800-511-FL-FL Series user’s Manual

BIOS Setup Utility

43

Device Configuration

A description of selected item appears on the right side of the screen. For items marked with
“”, please press <Enter> for more options.

Module Device Configuration

This option appears only if an I/O board is installed CN2 and CN3 (See Section 2.5.1). BIOS
will auto-detect all supported functions and you can use it to change settings on the I/O board.
The PICO511 supports the following I/O boards: AX93A00, AX93A01, AX93A02 and
AX93A09.

eBOX800-511-FL-FL Series user’s Manual

BIOS Setup Utility

44

Module Device Configuration

This screen is available only if an I/O board with serial ports is connected. For items marked
with “”, please press <Enter> for more options.

AxiomType3 Super IO Configuration

eBOX800-511-FL-FL Series user’s Manual

BIOS Setup Utility

45

Serial Port 1~2 Configuration
Set parameters related to serial port 1~2 on I/O board.

eBOX800-511-FL-FL Series user’s Manual

BIOS Setup Utility

46

Serial Port 1 Configuration

COM Port Type

Use this item to set RS-232/422/485 communication mode.

Terminal Mode

Enable or disable terminal mode.

eBOX800-511-FL-FL Series user’s Manual

BIOS Setup Utility

47

4.5 Chipset Menu

The Chipset menu allows users to change the advanced chipset settings. Users can select
any of the items in the left frame of the screen to go to the sub menus:

► PCH-IO Configuration
► System Agent (SA) Configuration

For items marked with “”, please press <Enter> for more options.

eBOX800-511-FL-FL Series user’s Manual

BIOS Setup Utility

48

HD Audio
For items marked with “ , please press <Enter> for more options.

HD Audio Configuration

Use this item to set HD audio configuration.

eBOX800-511-FL-FL Series user’s Manual

BIOS Setup Utility

49

System Agent (SA) Configuration

This screen allows users to configure parameters of South Bridge chipset.

Graphics Configuration

Use this item to open graphics configuration sub screen.

Memory Configuration

Use this item to refer to information related to system memory.

eBOX800-511-FL-FL Series user’s Manual

BIOS Setup Utility

50

Primary IGFX Boot Display

Select the video device which will be activated during POST (Power-On Self Test).

eBOX800-511-FL-FL Series user’s Manual

BIOS Setup Utility

51

Memory information

This screen shows the system memory information.

eBOX800-511-FL-FL Series user’s Manual

BIOS Setup Utility

52

Security Menu

Administrator Password

This item indicates whether an administrator password has been set (installed or uninstalled).

User Password

This item indicates whether a user password has been set (installed or uninstalled).

eBOX800-511-FL-FL Series user’s Manual

BIOS Setup Utility

53

4.6 Boot Menu

The Boot menu allows users to change boot options of the system.

Bootup NumLock State

Use this item to select the power-on state for the keyboard NumLock.



Quiet Boot

Select to display either POST output messages or a splash screen during boot-up.



Legacy PXE OpROM

Use this item to enable or disable the boot ROM function of the onboard LAN chip when the
system boots up.

Boot Option Priorities

These are settings for boot priority. Specify the boot device priority sequence from the
available devices.

Hard Drive BBS Priorities

These are settings for configuring the order for a specific device group. These options are only
visible if at least one device for this group is present.

eBOX800-511-FL-FL Series user’s Manual

BIOS Setup Utility

54

4.7 Save & Exit Menu

The Save & Exit menu allows users to load system configurations with optimal or fail-safe
default values.

Save Changes and Exit

When users have completed the system configuration changes, select this option to leave
Setup and return to Main Menu. Select Save Changes and Exit from the Save & Exit menu
and press <Enter>. Select Yes to save changes and exit.

Discard Changes and Exit

Select this option to quit Setup without making any permanent changes to the system
configurations and return to Main Menu. Select Discard Changes and Exit from the Save &
Exit menu and press <Enter>. Select Yes to discard changes and exit.

Save Changes and Reset

When completed the system configuration changes, select this option to leave Setup and
reboot the computer so the new system configurations take effect. Select Save Changes and
Reset from the Save & Exit menu and press <Enter>. Select Yes to save changes and reset.

Discard Changes and Reset

Select this option to quit Setup without making any permanent changes to the system
configuration and reboot the computer. Select Discard Changes and Reset from the Save &
Exit menu and press <Enter>. Select Yes to discard changes and reset.

eBOX800-511-FL-FL Series user’s Manual

BIOS Setup Utility

55

Save Changes

When completed the system configuration changes, select this option to save changes. Select
Save Changes from the Save & Exit menu and press <Enter>. Select Yes to save changes.

Discard Changes

Select this option to quit Setup without making any permanent changes to the system
configurations. Select Discard Changes from the Save & Exit menu and press <Enter>. Select
Yes to discard changes.

Restore Defaults

It automatically sets all Setup options to a complete set of default settings when users select
this option. Select Restore Defaults from the Save & Exit menu and press <Enter>.

Save as User Defaults

Select this option to save system configuration changes done so far as User Defaults. Select
Save as User Defaults from the Save & Exit menu and press <Enter>.

Restore User Defaults

It automatically sets all Setup options to a complete set of User Defaults when users select
this option. Select Restore User Defaults from the Save & Exit menu and press <Enter>.

Boot Override

Select a drive to immediately boot that device regardless of the current boot order.

eBOX800-511-FL-FL Series user’s Manual

BIOS Setup Utility

56

This page is intentionally left blank.

eBOX800-511-FL-FL Series user’s Manual

Watchdog Timer 57

APPENDIX A

WATCHDOG TIMER

A.1 About Watchdog Timer

After the system stops working for a while, it can be auto-reset by the watchdog timer. The
integrated watchdog timer can be set up in the system reset mode by program.

A.2 How to Use Watchdog Timer

Assembly sample code :

mov dx,fa10 ; 5 seconds (Maximum is 65535 seconds; fill in

; 0xFA10 and 0xFA11 register, ex:

0xFA11=0x01,

; 0xFA10=0x68 means 360 seconds)

mov al,05

out dx,al

mov dx,fa12 ; Enable WDT

mov al,01

out dx,al

eBOX800-511-FL-FL Series user’s Manual

58 Watchdog Timer

This page is intentionally left blank.

eBOX800-511-FL-FL Series user’s Manual

iAMT Settings

59

APPENDIX B

iAMT SETTINGS

The Intel® Active Management Technology (Intel® iAMT) has decreased a major barrier to IT
efficiency that uses built-in platform capabilities and popular third-party management and
security applications to allow IT a better discovering, healing, and protection their networked
computing assets.

In order to utilize Intel® iAMT you must enter the ME BIOS (<Ctrl + P> during system startup),
change the ME BIOS password, and then select “Intel® iAMT” as the manageability feature.

B.1 Entering MEBx

1. Go to BIOS to enable iAMT function (see section 4.4).

2. Exit from BIOS after starting iAMT, and press <Ctrl + P> to enter MEBx Setting.

Note

It is better to press <Ctrl + P> before the screen popping out.

B.2 Set and Change Password

1. You will be asked to set a password when first log in. The default password is “admin”.

eBOX800-511-FL-FL Series user’s Manual

iAMT Settings

60

2. You will be asked to change the password before setting ME.

3. You must confirm your new password while revising. The new password must contain:

(example: !!11qqQQ) (default value).

 Eight characters
 One upper case
 One lower case
 One number
 One special symbol, such as ! 、 $ or ; ， (、 " , excepted)

Underline ( _ ) and space are valid characters for password, but they won’t make higher
complexity.

4. From Main Menu, select ME General Settings to get into ME Platform Configuration

screen. In this screen you can modify Local FW Update setting.

5. Return to Main Menu.

eBOX800-511-FL-FL Series user’s Manual

iAMT Settings

61

B.3 iAMT Configuration

1. From Main Menu, select Intel

®

Standard Manageability Configuration and press <Enter>.

2. Set Manageability Feature Selection to Enabled.

eBOX800-511-FL-FL Series user’s Manual

iAMT Settings

62

 SOL/Storage Redirection/KVM

This screen is for enabling or disabling Serial-over-LAN (SOL)/Storage
Redirection/Keyboard Video Mouse (KVM) functionality.

 User Consent

i

eBOX800-511-FL-FL Series user’s Manual

iAMT Settings

63

User Opt-in

Configure this item when user consent should be required.

Opt-in Configurable from Remote IT

Enable or disable remote change capability of user consent feature.

 Network Setup

1. From Intel® AMT Configuration Menu, select Network Setup.

2. Select ME Network Name Settings to set computer host and domain name.

eBOX800-511-FL-FL Series user’s Manual

iAMT Settings

64

3. Select TCP/IP to get into Network interface. Get into DHCP Mode and set it to Disabled.

eBOX800-511-FL-FL Series user’s Manual

iAMT Settings

65

4. If DHCP Mode is disabled, set the following settings:

 IP address
 Subnet mask

5. Go back to Intel® iAMT Configuration, then select Activate Network Access and press
<Enter>.

eBOX800-511-FL-FL Series user’s Manual

iAMT Settings

66

6. Exit from MEBx after completing the iAMT settings.

 Remote Setup and Configuration

1. Select TLS PKI to get into remote configuration screen. Then select Start Configuration
to activate it.

eBOX800-511-FL-FL Series user’s Manual

iAMT Settings

67

2. Select Manage Hashes to add, delete and activate hash.

eBOX800-511-FL-FL Series user’s Manual

iAMT Settings

68

 Power Control

AMT ON in Host Sleep States

Select the appropriate AMT ON in Host Sleep States setting. Options are ON in S0 and
ON in S0, ME Wake in S3, S4-5 (AC only).

Idle Timeout

This is timeout value for Wake_On_ME in minutes. It must be set to a non-zero value.

eBOX800-511-FL-FL Series user’s Manual

iAMT Settings

69

B.4 iAMT Web Console

1. From a web browser, please type http://(IP ADDRESS):16992, which connects to iAMT

Web.

Example: http://10.1.40.214:16992

2. To log on, you will be required to type in username and password for access to the Web.

USER: admin (default value)
PASS: (MEBx password)

eBOX800-511-FL-FL Series user’s Manual

iAMT Settings

70

3. Enter the iAMT Web.

4. Click Remote Control, and select commands on the right side.

5. When you have finished using the iAMT Web console, close the Web browser.

eBOX800-511-FL-FL Series user’s Manual

BIOS Flash Utility

71

APPENDIX C

BIOS Flash Utility

The BIOS Flash utility is a new helpful function in BIOS setup program. With this function you
can easily update system BIOS without having to enter operating system. In this appendix you
may learn how to do it in just a few steps. Please read and follow the instructions below
carefully.

1. In your USB flash drive, create a new folder and name it “Axiomtek”, see figure below.

2. Copy BIOS ROM file (e.g. PICO511.005) to “Axiomtek” folder.

3. Insert the USB flash drive to your system.

eBOX800-511-FL-FL Series user’s Manual

BIOS Flash Utility

72

4. Enter BIOS setup menu and go to Advanced\Utility Configuration. Select BIOS Flash
Utility and press <Enter>.

5. BIOS automatically detect all USB drive(s) attached to the system. In this example only
one USB drive is attached to the system. That’s why, you can see only one device is
displayed in figure below.

6. Select the USB drive containing BIOS ROM file you want to update using the <> or
<> key. Then press <Enter> to get into “Axiomtek” folder.

eBOX800-511-FL-FL Series user’s Manual

BIOS Flash Utility

73

7. Now you can see the BIOS ROM file on the screen, press <Enter> to select.

8. Select Start to flash system BIOS option to begin updating procedure.

PICO511.005

eBOX800-511-FL-FL Series user’s Manual

BIOS Flash Utility

74

9. Please wait while BIOS completes the entire flash update process: erase data, write new
data and verify data.

10. When you see the following figure, press <Enter> to finish the update process. After that
the system will shut down and restart immediately.

eBOX800-511-FL-FL Series user’s Manual

IO Board

75

APPENDIX D

IO BOARD

The AX93287/AX93A00 is an I/O expansion board which is suggested to attach carefully to
PICO511. Its specifications and detailed information are given in this appendix.

AX93287 TOP View AX93287 Side View

Ethernet Connector from AX93287 (CN1)

Note: CN1 is suggested to connect CN3 on AX92902 via LAN cable.

Pins

Signals

Pins

Signals

1

100_LAN_LED

9

MDI1-

2

1000_LAN_LE
D

10

MDI1+
3

NC

11

NC 4 MDI3-

12

MDI0-

5

MDI3+

13

MDI0+

6

NC

14

NC 7 MDI2-

15

LINK_ACT

8

MDI2+

16

VDD3

Pins

Signals

Pins

Signals

L1

MDI0+

L5

MDI2+

L2

MDI0-

L6

MDI2-

L3

MDI1+

L7

MDI3+

L4

MDI1-

L8

MDI3-

A

100 LAN LED (Green) / 1000 LAN LED
(Orange)

B

Active LED (Yellow)

eBOX800-511-FL-FL Series user’s Manual

IO Board

76

AX93A00 TOP View

CN9

CN5

CN10

JP1
JP2

D18

CN3

CN8

JP3

CN4

CN6

CN7

CN1

CN2

1

1

1

AX93A00 side view

AX93A00

Jumpers

Descriptions

Settings

JP1

USB port 0 and 1
Power Selection

+5V_SBY (Default)

1-2 Close

+5V

2-3 Close

JP2

USB port 2 and 3
Power Selection

+5V_SBY (Default)

1-2 Close

+5V

2-3 Close

JP3

COM1 Data/Power
Selection

Power: Set COM1 pin 9 to +12V level

1-3 Close

RS-232 Data: Set COM1 pin 9 to RI
(Default)

3-5 Close

Power: Set COM1 pin 1 to +5V level

2-4 Close

RS-232 Data: Set COM1 pin 1 to DCD
(Default)

4-6 Close

COM 1 Connector (CN8)

Pins

RS-232

RS-422

RS-485

1

DCD

TX-

Data-

2

RXD

TX+

Data+

3

TXD

RX+

No use

4

DTR

RX-

No use

5

GND

No use

No use

6

DSR

No use

No use

7

RTS

No use

No use

8

CTS

No use

No use

9

RI

No use

No use

eBOX800-511-FL-FL Series user’s Manual

IO Board

77

COM 2 Wafer Connector (CN4)

Pins

RS-232

RS-422

RS-485

1

DCD

TX-

Data-

2

DSR

No use

No use

3

RXD

TX+

Data+

4

RTS

No use

No use

5

TXD

RX+

No use

6

CTS

No use

No use

7

DTR

RX-

No use

8

RI

No use

No use

9

GND

No use

No use

10

No use

No use

No use