AXIOMTEK eBOX670-883-FL-DC User Manual

eBOX670-883-FL Series

Embedded System

User’s Manual

ii

Disclaimers

This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third
party’s rights, and any liability arising from such use.

Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make any
commitment to update the information in this manual.

Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.

No part of this document may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written permission of Axiomtek Co., Ltd.

Copyright 2014 Axiomtek Co., Ltd.
All Rights Reserved
Aug 2014, Version A1
Printed in Taiwan

iii

Safety Precautions

Before getting started, please read the following important safety precautions.

1. The eBOX670-883-FL does not come equipped with an operating system. An operating
system must be loaded first before installing any software into the computer.

2. Be sure to ground yourself to prevent static charge when installing the internal
components. Use a grounding wrist strap and place all electronic components in any
static-shielded devices. Most electronic components are sensitive to static electrical
charge.

3. Disconnect the power cord from the eBOX670-883-FL before making any installation. Be
sure both the system and the external devices are turned OFF. Sudden surge of power
could ruin sensitive components. Make sure the eBOX670-883-FL is properly grounded.

4. Make sure the voltage of the power source is correct before connecting the equipment to
the power outlet.

5. Turn OFF the system power before cleaning. Clean the system using a cloth only. Do not
spray any liquid cleaner directly onto the screen.

6. Do not leave this equipment in an uncontrolled environment where the storage
temperature is below -45℃ or above 80℃. It may damage the equipment.

7. Do not open the system’s back cover. If opening the cover for maintenance is a must,
only a trained technician is allowed to do so. Integrated circuits on computer boards are
sensitive to static electricity. To avoid damaging chips from electrostatic discharge,
observe the following precautions:

 Before handling a board or integrated circuit, touch an unpainted portion of the

system unit chassis for a few seconds. This will help to discharge any static electricity
on your body.

 When handling boards and components, wear a wrist-grounding strap, available from

most electronic component stores.

iv

Classification

1. Degree of production against electric shock : not classified

2. Degree of protection against the ingress of water : IP40

3. Equipment not suitable for use in the presence of a flammable anesthetic mixture with air

or with oxygen or nitrous oxide.

4. Mode of operation : Continuous

v

General Cleaning Tips

You may need the following precautions before you begin to clean the computer. When you
clean any single part or component for the computer, please read and understand the details
below fully.

When you need to clean the device, please rub it with a piece of dry cloth.

1. Be cautious of the tiny removable components when you use a vacuum cleaner to
absorb the dirt on the floor.

2. Turn the system off before you start to clean up the component or computer.

3. Never drop the components inside the computer or get circuit board damp or wet.

4. Be cautious of all kinds of cleaning solvents or chemicals when you use it for the sake of
cleaning. Some individuals may be allergic to the ingredients.

5. Try not to put any food, drink or cigarette around the computer.

Cleaning Tools:

Although many companies have created products to help improve the process of cleaning
your computer and peripherals users can also use household items to clean their computers
and peripherals. Below is a listing of items you may need or want to use while cleaning your
computer or computer peripherals.

Keep in mind that some components in your computer may only be able to be cleaned using a
product designed for cleaning that component, if this is the case it will be mentioned in the
cleaning.

 Cloth: A piece of cloth is the best tool to use when rubbing up a component. Although

paper towels or tissues can be used on most hardware as well, we still recommend you
to rub it with a piece of cloth.

 Water or rubbing alcohol: You may moisten a piece of cloth a bit with some water or

rubbing alcohol and rub it on the computer. Unknown solvents may be harmful to the
plastics parts.

 Vacuum cleaner: Absorb the dust, dirt, hair, cigarette particles, and other particles out of

a computer can be one of the best methods of cleaning a computer. Over time these
items can restrict the airflow in a computer and cause circuitry to corrode.

 Cotton swabs: Cotton swaps moistened with rubbing alcohol or water are excellent tools

for wiping hard to reach areas in your keyboard, mouse, and other locations.

 Foam swabs: Whenever possible it is better to use lint free swabs such as foam swabs.

Note: We strongly recommended that you should shut down the system before you

start to clean any single components.

Please follow the steps below:

1. Close all application programs

2. Close operating software

3. Turn off power switch

4. Remove all device

5. Pull out power cable

vi

Scrap Computer Recycling

If the computer equipment’s needs the maintenance or are beyond repair, we strongly
recommended that you should inform your Axiomtek distributor as soon as possible for the
suitable solution. For the computers that are no longer useful or no longer working well, please
contact your Axiomtek distributor for recycling and we will make the proper arrangement.

Trademarks Acknowledgments

Axiomtek is a trademark of Axiomtek Co., Ltd.
IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation.
Intel® and Pentium® are registered trademarks of Intel Corporation.
MS-DOS, Microsoft C and QuickBasic are trademarks of Microsoft Corporation.
Windows 8, Windows 7, Windows XPE, Windows XP, Windows WinCE embedded, Linux,
MS-DOS, Microsoft C and
Other brand names and trademarks are the properties and registered brands of their
respective owners.

vii

Table of Contents

Disclaimers .............................................................................................................. ii

Safety Precautions ................................................................................................. iii

Classification .......................................................................................................... iv

General Cleaning Tips ............................................................................................ v

Scrap Computer Recycling .................................................................................... vi

CHAPTER 1 INTRODUCTION ................................................................................. 1

1.1 General Description ............................................................................ 1

1.2 System Specifications ........................................................................ 3

1.2.1 CPU .................................................................................................................... 3

1.2.2 I/O System ......................................................................................................... 3

1.2.3 System Specification ........................................................................................ 3

1.2.4 Driver CD Content ............................................................................................. 4

1.3 Dimensions ......................................................................................... 5

1.3.1 System Dimension ............................................................................................ 5

1.3.2 Wall mount Bracket Dimension ....................................................................... 6

1.4 I/O Outlets ........................................................................................... 7

1.5 Packing List ......................................................................................... 9

1.6 Model List ............................................................................................ 9

CHAPTER 2 HARDWARE INSTALLATION ........................................................ 11

2.1 Installing the 2.5” SATA Device ....................................................... 11

2.2 Installing the Express Mini Card ...................................................... 14

2.3 Installing the CFast Card .................................................................. 15

2.4 Installing the SIM Card ..................................................................... 16

2.5 Installing the SO-DIMM Memory ...................................................... 17

CHAPTER 3 JUMPER SETTING & CONNECTOR ............................................ 19

3.1 Jumper & Connector Location ......................................................... 19

3.2 Jumper Setting Summary ................................................................. 20

3.2.1 Restore BIOS Optimal Defaults (SJP2) ......................................................... 20

3.2.2 Mini Card Selection (SJP3) ............................................................................ 20

3.3 Connectors ........................................................................................ 21

3.3.1 DC-in Phoenix Power Connector .................................................................. 22

3.3.2 VGA Connector ............................................................................................... 22

3.3.3 HDMI Connector .............................................................................................. 22

3.3.4 DisplayPort Connector ................................................................................... 23

3.3.5 COM1~COM6 Serial Port Connector ............................................................. 23

3.3.6 USB 3.0 Connector ......................................................................................... 24

3.3.7 Ethernet Connector (LAN1~LAN4) ................................................................ 24

3.3.8 Audio Connector (SCN2, SCN1) .................................................................... 25

3.3.9 ATX Power On/OFF Button ............................................................................ 25

3.3.10 Reset Button .................................................................................................... 25

3.3.11 Remote Power Switch Connector (SPWRBT1) ............................................ 25

3.3.12 AT/ATX Switch................................................................................................. 26

viii

3.3.13 SIM Card Slots ................................................................................................. 26

3.3.14 Serial ATA Connectors (SATA1-SATA2) ....................................................... 26

3.3.15 CFast™ Socket ................................................................................................ 27

3.3.16 Digital I/O Connector ...................................................................................... 28

3.3.17 Express Mini Card Slot (SCN12, SCN13) ...................................................... 29

CHAPTER 4 BIOS SETUP UTILITY ..................................................................... 31

4.1 Starting .............................................................................................. 31

4.2 Advanced Menu ................................................................................. 33

4.3 Chipset Menu .................................................................................... 44

4.4 Boot Menu ......................................................................................... 48

4.5 Security Menu ................................................................................... 49

4.6 Save & Exit Menu .............................................................................. 50

APPENDIX A WATCHDOG TIMER ....................................................................... 53

About Watchdog Timer .................................................................................... 53

Sample Program ............................................................................................... 54

APPENDIX B PROGRAMMABLE LED ................................................................ 55

About Programmable LED ............................................................................... 55

Sample Code ..................................................................................................... 55

eBOX670-883-FL Series User’s Manual

Introduction

1

CHAPTER 1

INTRODUCTION

This chapter contains general information and detailed specifications of the eBOX670-883-FL.
The Chapter 1 includes the following sections:

 General Description
 System Specifications
 Dimensions
 I/O Outlets
 Packing List
 Model List

1.1 General Description

The eBOX670-883-FL is an embedded system that supports LGA1150 Socket 4th
generation Intel® Core™ i7/i5/i3/Celeron processor to support Windows 7, Windows
7 Embedded, Windows 8, Windows 8 Embedded or Linux, suitable for the most
endurable operation.

It features fan less design with full feature I/O, two 204-pin unbuffered SODIMM
socket for dual channel DDR3-1333/1600 MHz memory, and enhanced system
dependability by built-in Watchdog Timer.

 Features

1. Intel

®

Haswell Q87 Platform

2. Support LGA1150 Socket Intel® Core™ i7/i5/i3/Celeron processor

3. Maximum to 16GB SO-DIMM DDR3 1333/1600 MHz memory

4. Supports 6 USB 3.0 ports

5. Supports 6 jump-less RS-232/422/485

6. Supports 4 10/100/1000Mbps Ethernet ports

7. Supports ATX power switch with status indicator

8. 32 channel Digital I/O (16 IN & 16 OUT), Programmable

9. Two HDMI

10. One DisplayPort

11. One VGA

12. Two 2.5” SATA HDD drive bay

13. Two PCI Express Mini Card Slots w/ mSATA supported. (By jumper selection)

14. One front access CFast

15. Watchdog timer

16. VDC power input 9~36V

17. One SIM slot

18. Three Antenna openings

eBOX670-883-FL Series User’s Manual

Introduction

2

 Reliable and Stable Design

The eBOX670-883-FL adopts the advanced cooling system and supporting the CFast™,
which makes it especially suitable for vibration environments, best for industrial
automation, digital signage and gaming application.

 Embedded O.S. Supported

The eBOX670-883-FL not only supports Windows 7, Windows 8, but also supports
embedded OS, such as Windows 7 Embedded, Windows 8 Embedded and Linux.

 Various Storage devices supported

For storage device, the eBOX670-883-FL supports two 2.5" SATA storage drive bay, one
CFast™ slot and mSATA device.

eBOX670-883-FL Series User’s Manual

Introduction

3

1.2 System Specifications

1.2.1 CPU

 CPU

 LGA1150 Socket Intel® Core™ i7/i5/i3/Celeron processor
 Working temperature depends on TDP of processor, please refer to 1.2.3

System Specification

 Chipset

 Intel® Haswell Q87 chipset

 BIOS

 American Megatrends Inc. UEFI (Unified Extensible Firmware Interface)

BIOS.

 System Memory

 Two 204-pin unbuffered DDR3 1333/1600 MHz SO-DIMM socket, max. up

to 16GB

1.2.2 I/O System

 Six jumper-less RS-232/422/485 9-pin D-Sub male connectors
 Two HDMI for display (Supports HDMI 1.4a, max resolution up to 4K × 2K)
 One VGA connector for display (Supports max resolution up to 1920x1200)
 One DisplayPort for display (Supports max resolution up to 2560x1600)
 One Audio connector (Mic-IN, Line-OUT)
 Four RJ-45 connectors for 10/100/1000 Base-T Ethernet ports

(Intel® i210-IT,i217-LM )

 Six USB 3.0 connectors
 16 Digital Input and 16 Digital Output for digital I/O 44-pin D-Sub female connectors
 Two PCI Express Mini Card Slots w/ mSATA supported.
 DC 9~36V power input connector
 Oner HDD Active and two programmable indicators
 One Reset switch
 One AT/ATX switch
 One Power switch
 One Remote PWR switch
 Three SMA type connector opening for Antenna

1.2.3 System Specification

 Watchdog Timer

 1~255 seconds or minutes; up to 255 levels.

 Power Supply

 9-36V wide range DC input connector

 Operation Temperature

 -40℃ ~ 55℃ (-4 ºF ~ 131ºF), with W.T. SSD & Memory ;CPU TDP 35W)
 -40℃ ~ 50℃ (-4 ºF ~ 122ºF), with W.T. SSD & Memory ;CPU TDP 45W )

eBOX670-883-FL Series User’s Manual

Introduction

4

 Storage Temperature

 -45℃ ~ 80℃ (-49 ºF ~ 176ºF)

 Humidity

 10% ~ 90% (non-condensation)

 Vibration Endurance

 3Grm w/ CFast (5-500Hz, X, Y, Z directions)

 Weight

 3.8 kg (8.37 lb) without package
 4.6 kg (10.14 lb) with package

 Dimensions

 280mm(11.02”) (W) x190mm(7.48”) (D) x 70mm(2.75”) (H)

1.2.4 Driver CD Content

 Driver

 Audio
 Chipset
 Ethernet
 Graphic
 Intel Rapid Storage Technology
 USB 3.0
 ME 9.0

 Manual

 User Manual
 Quick Manual

Note: All specifications and images are subject to change without notice.

eBOX670-883-FL Series User’s Manual

Introduction

5

1.3 Dimensions

The following diagrams show you dimensions and outlines of the eBOX670-883-FL.

1.3.1 System Dimension

eBOX670-883-FL Series User’s Manual

Introduction

6

1.3.2 Wall mount Bracket Dimension

eBOX670-883-FL Series User’s Manual

Introduction

7

1.4 I/O Outlets

The following figures show you I/O outlets on front view of the eBOX670-883-FL.

 Front View drawing

※ Indicator Information:

HDD: 1 x Orange LED for HDD active
PL1: Programmable LED (Please refer to Appendix B to set it.)
PL2: Programmable LED (Please refer to Appendix B to set it.)

eBOX670-883-FL Series User’s Manual

Introduction

8

 Rear View drawing

eBOX670-883-FL Series User’s Manual

Introduction

9

1.5 Packing List

The package bundled with your eBOX670-883-FL should contain the following items:

 eBOX670-883-FL System Unit x 1
 eBOX670-883-FL Quick Installation Guide x 1
 CD x 1 (For Driver and Manual)
 Screws Pack x1
 Pre-installed Intel Processor
 Pre-installed DDR3 SO-DIMM
 Pre-installed Foot pad x4
 Optional Wall-mount Brackets
 Optional Antenna
 Optional Mini Card module
 Optional 2.5” SATA Storage
 Optional CFast™Card
 Optional mSATA

1.6 Model List

eBOX670-883-FL-DC

Fanless Embedded System with Intel Core i7/i5/i3 &
Celeron Processor, Q87 PCH, HDMIx2/VGA/DisplayPort,
Dual HDD, GbE LAN*4, USB3.0*6, Audio, RS­232/422/485*6, 32 Channel digital I/O, 9~36VDC

If you cannot find this package or any items are missing, please contact Axiomtek distributors
immediately.

eBOX670-883-FL Series User’s Manual

Introduction

10

This page is intentionally left blank.

eBOX670-883-FL Series User’s Manual

Hardware Installation

11

CHAPTER 2

HARDWARE INSTALLATION

The eBOX670-883-FL is convenient for your various hardware configurations, such as HDD
(Hard Disk Drive), SSD (Solid State Drive), CFastTM card or PCI Express Mini Card modules.
The chapter 2 will show you how to install the hardware.

2.1 Installing the 2.5” SATA Device

<< HDD-A >>
Step 1 Turn off the system, and unplug the power cord.

Step 2 Turn the system upside down to locate screws at the bottom, loosen

screws.

Step 3 Remove the bottom cover.
Step 4 Please find the HDD bracket location then loosen four screws of HDD

bracket to take out it.

Step 5 Please prepare the following items to assemble HDD.

eBOX670-883-FL Series User’s Manual

Hardware Installation

12

Step 6 Fasten total four screws between two sides of HDD/SSD.

※ Please notice that you should base on the photo to check HDD’ s direction.

Step 7 Lock the HDD and fasten screws then connect SATA & Power cables.

Step 8 Please fasten screws of HDD bracket to complete first HDD installation.

eBOX670-883-FL Series User’s Manual

Hardware Installation

13

<< HDD-B >>
Step 1 Please find the HDD bracket location then loosen four screws of HDD

bracket to take out it.

Step 2 You can refer to below photo to find out four screw holes and then set

your HDD on bracket.

Step 3 Then turn the bracket upside down then fasten screws with your 2.5”

HDD/SSD. Connect SATA and Power cables.

Step 4 Finally, set the bracket into chassis then fasten screws to fix it.

eBOX670-883-FL Series User’s Manual

Hardware Installation

14

2.2 Installing the Express Mini Card

Step 1 Turn off the system, and unplug the power cord.
Step 2 Turn the system upside down to locate screws at the bottom, loosen

screws.

Step 3 Remove the top cover then find Mini Card location.

Step 4 Please follow your requirement to connect PCI Express Mini Card

module, EX: 3G/4G, WIFI, mSATA and GPS/Bluetooth modules.
Slide Mini card into Mini Card slot with caution, and fasten screw of

Express Mini Card.

Step 5 Assembly the Bottom Cover back and fasten all screws.

eBOX670-883-FL Series User’s Manual

Hardware Installation

15

2.3 Installing the CFast Card

Step 1 Turn off the system, and unplug the power cord.

Step 2 Turn the system to the side with CFast & SIM cover.

Step 3 Loosen screws to remove the CFast & SIM cover.

Step4 Slide CFast card into CFast slot with caution.

Step5 Close the cover to the chassis and fasten all screws.

eBOX670-883-FL Series User’s Manual

Hardware Installation

16

2.4 Installing the SIM Card

Step 1 Turn off the system, and unplug the power cord.

Step 2 Turn the system to the side with CFast & SIM cover.

Step 3 Loosen screws to remove the CFast & SIM cover.

\

Step4 Insert SIM card into SIM slot with caution.

Step5 Close the cover to the chassis and fasten all screws.

eBOX670-883-FL Series User’s Manual

Hardware Installation

17

2.5 Installing the SO-DIMM Memory

Basically, we strongly recommend you to order SO-DIMM memory from Axiomtek,
since we can follow your requirement to assemble compatible SO-DIMM memory to
avoid any unexpected problems. If you would like to assemble memory or upgrade
memory; please refer to the following information to add thermal pad by yourself.

Step 1 Turn off the system, and unplug the power cord.
Step 2 Please loosen all of screws and hexagon copper pillars, since two SO-

DIMM slots are on the top side of main board.

Step 3 You can get thermal pad of memory from accessory box.
(If you don’t order memory from Axiomtek, you will get them from accessory box.)

Step 4 Stick the thermal pad onto motherboard then insert your memory to the

slot.

eBOX670-883-FL Series User’s Manual

Hardware Installation

18

This page is intentionally left blank.

eBOX670-883-FL Series User’s Manual

Jumper Setting & Connector

19

CHAPTER 3

JUMPER SETTING & CONNECTOR

Proper jumper settings configure the eBOX670-883-FL to meet your application purpose. We
are herewith listing a summary table of all jumpers and default settings for onboard devices,
respectively.

3.1 Jumper & Connector Location

SBC87883 Top Side

SBC87883 Bottom Side

Note: We strongly recommended that you should not modify any unmentioned

jumper setting without Axiomtek FAE’s instruction. Any modification
without instruction might cause system to become damage.

eBOX670-883-FL Series User’s Manual

Jumper Setting & Connector

20

3.2 Jumper Setting Summary

Proper jumper settings configure the eBOX670-883-FL to meet your application purpose. We
are herewith listing a summary table of all jumpers and default settings for onboard devices,
respectively.

Jumper

Function/Default Setting

Jumper Setting

SJP2

Restore BIOS Optimal Defaults

Default: Normal Operation

Short 1-2

SJP3

mSATA / PCIe Selection

SCN12: 3-5 Short
SCN13: 4-6 Short

Note: How to setup Jumpers

The illustration shows how to set up jumpers. When the jumper cap is placed on pins, the
jumper is “close”, if not, that means the jumper is “open”.

[Open] [Closed] [Pin1-2 Closed]

3.2.1 Restore BIOS Optimal Defaults (SJP2)

Put jumper clip to pin 2-3 for a few seconds then move it back to pin 1-2. Doing this procedure
can restore BIOS optimal defaults.

Function

Setting

Normal (Default)

1-2

Clear RTC

2-3

3.2.2 Mini Card Selection (SJP3)

Select mSATA or PCI-Express x1 support on PCI-Express Mini Card socket.

Function

SCN12

SCN13

mSATA

1-3 Short

2-4 Short

PCI-E/USB

3-5 Short

4-6 Short

eBOX670-883-FL Series User’s Manual

Jumper Setting & Connector

21

3.3 Connectors

Connectors connect the board with other parts of the system. Loose or improper
connection might cause problems. Make sure all connectors are properly and firmly
connected. Here is a summary table shows you all connectors and button on the

eBOX670-883-FL Series.

External Connectors / Buttons

Section

DC-in Phoenix Power Connector

3.3.1

VGA Connector

3.3.2

HDMI Connector

3.3.3

DisplayPort Connector

3.3.4

COM Serial Port Connector

3.3.5

USB 3.0 Connector

3.3.6

Ethernet Connector

3.3.7

Audio Connector

3.3.8

ATX Power On/OFF Button

3.3.9

Rest Button

3.3.10

Remote Power Switch Connector

3.3.11

AT/ATX Switch

3.3.12

SIM Card Slots

3.3.13

Serial ATA Connectors (SATA1-SATA2)

3.3.14

CFast Socket

3.3.15

Digital I/O Connector

3.3.16

PCI Express Mini Card interface

3.3.18

eBOX670-883-FL Series User’s Manual

Jumper Setting & Connector

22

3.3.1 DC-in Phoenix Power Connector

The system supports a wide range 9~36V Phoenix DC-in connector for system power
input.

Pin

Signal

1

DC+

2

GND

3

DC-

3.3.2 VGA Connector

The VGA connector is a slim type 15-pin D-Sub connector which is common for the
CRT VGA display. The VGA interface configuration can be configured via the
software utility.

3.3.3 HDMI Connector

The HDMI (High-Definition Multimedia Interface) is a compact digital interface which
is capable of transmitting high-definition video and high-resolution audio over a
single cable.

Pin

Signal

Pin

Signal

1

HDMI OUT_DATA2+

11

GND

2

GND

12

HDMI OUT Clock-

3

HDMI OUT_DATA2-

13

N.C.

4

HDMI OUT_DATA1+

14

N.C.

5

GND

15

HDMI OUT_SCL

6

HDMI OUT_DATA1-

16

HDMI OUT_SDA

7

HDMI OUT_DATA0+

17

GND

8

GND

18

+5V

9

HDMI OUT_DATA0-

19

HDMI_HTPLG

10

HDMI OUT Clock+

eBOX670-883-FL Series User’s Manual

Jumper Setting & Connector

23

3.3.4 DisplayPort Connector

DisplayPort interface is also called DP port.

Pin

Signal

1

DPB_LANE0

2

GND

3

DPB_LANE0#

4

DPB_LANE1

5

GND

6

DPB_LANE1#

7

DPB_LANE2

8

GND

9

DPB_LANE2#

10

DPB_LANE3

11

GND

12

DPB_LANE3#

13

Detect Pin

14

GND

15

DPB_AUX

16

GND

17

DPB_AUX#

18

DPB_HPDE

19

GND

20

+3.3V

3.3.5 COM1~COM6 Serial Port Connector

The system has six serial ports. COM1~COM6 are RS-232/422/485 ports. Please
refer to Chapter 4 for the detail of BIOS setting.

Pin

RS-232

RS-422

RS-485

COM1~COM6

1

DCD, Data Carrier Detect

TX-

Data-

2

RXD, Receive Data

TX+

Data+

3

TXD, Transmit Data

RX+

No use

4

DTR, Data Terminal Ready

RX-

No use

5

GND, Ground

No use

No use

6

DSR, Data Set Ready

No use

No use

7

RTS, Request To Send

No use

No use

8

CTS, Clear To Send

No use

No use

9

RI, Ring Indicator

No use

No use

eBOX670-883-FL Series User’s Manual

Jumper Setting & Connector

24

3.3.6 USB 3.0 Connector

The Universal Serial Bus connectors are compliant with USB 3.0 (5Gb/s), and ideally
for installing USB peripherals such as keyboard, mouse, scanner, etc.

Pin

Signal USB Port 0

Pin

Signal USB Port 1

1

USB_VCC (+5V level
standby power)

10

USB_VCC (+5V level standby
power)

2

USB_Data2-

11

USB_Data3-

3

USB_Data2+

12

USB_Data3+

4

GND

13

GND

5

SSRX2-

14

SSRX3-

6

SSRX2+

15

SSRX3+

7

GND

16

GND

8

SSTX2-

17

SSTX3-

9

SSTX2+

18

SSTX3+

3.3.7 Ethernet Connector (LAN1~LAN4)

The RJ-45 connector is for Ethernet-(Intel i210-IT, i217-V). To connect the board to a
1000/100/10 Base-T hub, just plug one end of the cable into connector and connect the other
end (phone jack) to a 1000/100/10-Base-T hub.

Pin

Signal

Pin

Signal

L1L2L3L4L5L6L7L8

A B

A B

L1

MDI0+

L5

MDI2-

L2

MDI0-

L6

MDI1-

L3

MDI1+

L7

MDI3+

L4

MDI2+

L8

MDI3-

A

Active LED (Yellow)

B

100 LAN LED (Green)/ 1000 LAN LED (Orange)

eBOX670-883-FL Series User’s Manual

Jumper Setting & Connector

25

3.3.8 Audio Connector (SCN2, SCN1)

These two audio jacks ideal are for Audio Mic-In and Audio Line-out.

Pin

Signal

1

Line Out

2

Microphone In

3.3.9 ATX Power On/OFF Button

The ATX power button is on the I/O side. It can allow users to control eBOX635-881­FL power on/off.

Function

Description

On

Turn on/off system

Off

Keep system status

3.3.10 Reset Button

The Reset button can allow users to reset eBOX635-881-FL.

Function

Description

On

Reset system

Off

Keep system status

3.3.11 Remote Power Switch Connector (SPWRBT1)

One 2-pin connector output for remote power on/off switch.

Function

Description

Short(1-2)

Turn on/off system

Open

Keep system status

eBOX670-883-FL Series User’s Manual

Jumper Setting & Connector

26

3.3.12 AT/ATX Switch

If you set AT/ATX switch to AT mode, the system will be automatically power on without
pressing soft power button during power input; we can use this switch to achieve auto power
on demand.

3.3.13 SIM Card Slots

eBOX670-883-FL includes one SIM slots on the bottom side of the system for inserting
SIM Card. It is mainly used in 3G wireless network application.

3.3.14 Serial ATA Connectors (SATA1-SATA2)

These Serial Advanced Technology Attachment (Serial ATA or SATA) connectors are for
high-speed SATA interfaces. They are computer bus interfaces for connecting to devices such
as hard disk drives. This board has two SATA 3.0 ports with 6Gb/s performance.

Pin

Signal

1

GND

2

SATA_TX+

3

SATA_TX-

4

GND

5

SATA_RX-

6

SATA_RX+

7

GND

eBOX670-883-FL Series User’s Manual

Jumper Setting & Connector

27

3.3.15 CFast™ Socket

The system is equipped with a CFast™ socket on the bottom side to support a
CFast™ card which is based on the Serial ATA bus. The socket is specially designed
to avoid incorrect installation of the CFast™ card. When installing or removing the
CFast™ card, please make sure the system power is off. The CFast™ card by
default identifies itself as C: or D: drive in your PC system.

Pin

Signal

Pin

Signal

S1

GND

PC1

NC

S2

TX+

PC2

GND

S3

TX-

PC3

NC

S4

GND

PC4

NC

S5

RX-

PC5

NC

S6

RX+

PC6

NC

S7

GND

PC7

GND

PC8

NC

PC9

NC

PC10

NC

PC11

NC

PC12

NC

PC13

3.3V

PC14

3.3V

PC15

GND

PC16

GND

PC17

NC

eBOX670-883-FL Series User’s Manual

Jumper Setting & Connector

28

3.3.16 Digital I/O Connector

The system is equipped with 32bit Programmable Digital I/O for 44-pin D-Sub female
connectors, please refer to the following table to get default pin define. Default is 16in/16out.

The digital I/O can be configured to control cash drawers and sense warning signals
from an Uninterrupted Power System (UPS), or perform store security control. You
may use software programming to control these digital signals.

Pin

Signal

Pin

Signal

1

VCC

2

VCC

3

Din 4 Dout 5 Din 6 Dout 7 Din 8 Dout 9 Din

10

Dout

11

Din

12

Dout

13

Din

14

Dout

15

Din

16

Dout

17

Din

18

Dout

19

Din

20

Dout

21

Din

22

Dout

23

Din

24

Dout

25

Din

26

Dout

27

Din

28

Dout

29

Din

30

Dout

31

Din

32

Dout

33

Din

34

Dout

35

GND

36

GND

37

N/A

38

N/A

39

N/A

40

N/A

41

N/A

42

N/A

43

N/A

44

N/A

eBOX670-883-FL Series User’s Manual

Jumper Setting & Connector

29

3.3.17 Express Mini Card Slot (SCN12, SCN13)

eBOX670-883-FL provides two PCI Express Mini Card slots and they all supports a PCI
Express x1 link and a USB 2.0 link with mSATA function. You can adjust SJP3 to set

mSATA function for SCN12 or SCN13.

eBOX670-883-FL Series User’s Manual

Jumper Setting & Connector

30

This page is intentionally left blank.

eBOX670-883-FL Series User’s Manual

BIOS Setup Utility

31

CHAPTER 4

BIOS SETUP UTILITY

This chapter provides users with detailed description how to set up basic system
configuration through the BIOS setup utility.

4.1 Starting

To enter the setup screens, follow the steps below:

1. Turn on the computer and press the <Del> key immediately.

2. After you press the <Del> key, the main BIOS setup menu displays. You can access the

other setup screens from the main BIOS setup menu, such as the Advanced and
Chipset menus.

It is strongly recommended that you should avoid changing the chipset’s defaults. Both AMI
and your system manufacturer have carefully set up these defaults that provide the best
performance and reliability.

4.2 Navigation Keys

The BIOS setup/utility uses a key-based navigation system called hot keys. Most of the BIOS
setup utility hot keys can be used at any time during the setup navigation process. These keys
include <F1>, <F2>, <Enter>, <ESC>, <Arrow> keys, and so on.

Note: Some of the navigation keys differ from one screen to another.

Hot Keys

Description

 Left/Right

The Left and Right <Arrow> keys allow you to select a setup screen.

 Up/Down

The Up and Down <Arrow> keys allow you to select a setup screen or sub­screen.

+ Plus/Minus

The Plus and Minus <Arrow> keys allow you to change the field value of a
particular setup item.

Tab

The <Tab> key allows you to select setup fields.

F1

The <F1> key allows you to display the General Help screen.

F2

The <F2> key allows you to Load Previous Values.

F3

The <F3> key allows you to Load Optimized Defaults.

F4

The <F4> key allows you to save any changes you have made and exit
Setup. Press the <F4> key to save your changes.

Esc

The <Esc> key allows you to discard any changes you have made and exit
the Setup. Press the <Esc> key to exit the setup without saving your
changes.

Enter

The <Enter> key allows you to display or change the setup option listed for
a particular setup item. The <Enter> key can also allow you to display the
setup sub- screens.

eBOX670-883-FL Series User’s Manual

BIOS Setup Utility

32

4.3 Main Menu

The first time you enter the setup utility, you will enter the Main setup screen. You can always
return to the Main setup screen by selecting the Main tab. System Time/Date can be set up as
described below. The Main BIOS setup screen is shown below.

BIOS Information

Display the auto-detected BIOS information.

System Date/Time

Use this option to change the system time and date. Highlight System Time or System Date
using the <Arrow> keys. Enter new values through the keyboard. Press the <Tab> key or the
<Arrow> keys to move between fields. The date must be entered in MM/DD/YY format. The
time is entered in HH:MM:SS format.

Access Level

Display the access level of current user.

eBOX670-883-FL Series User’s Manual

BIOS Setup Utility

33

4.2 Advanced Menu

 Launch PXE OpROM

Use this item to enable or disable the boot ROM function of the onboard LAN chip when
the system boots up.

The Advanced menu also allows users to set configuration of the CPU and other system
devices. You can select any of the items in the left frame of the screen to go to the sub menus:

► ACPI Settings
► CPU Configuration
► IDE Configuration
► NCT6627UD Super IO Configuration
► NCT6627UD HW Monitor

For items marked with “”, please press <Enter> for more options.

eBOX670-883-FL Series User’s Manual

BIOS Setup Utility

34

 ACPI Settings

You can use this screen to select options for the ACPI configuration, and change the value of
the selected option. A description of the selected item appears on the right side of the screen.

ACPI Sleep State

Allow you to select the Advanced Configuration and Power Interface (ACPI) sleep state. Here
are the options for your selection: Suspend Dissabled and S3 (Suspend to RAM). The S3
(Suspend to RAM) option selects the highest ACPI sleep state the system will enter when
SUSPEND button is pressed.

eBOX670-883-FL Series User’s Manual

BIOS Setup Utility

35

 CPU Configuration

This screen shows the CPU information.

Hyper-threading

To enable hyperthreading you must first enable it in your system's BIOS settings, the default is enabled.

Intel Virtualization Technology

If you want to enable or disable Intel Virtualization Technology function through BIOS,

please adjust this item.

eBOX670-883-FL Series User’s Manual

BIOS Setup Utility

36

 SATA Configuration

In this Configuration menu, you can see the currently installed hardware in the SATA ports.
During system boot up, the BIOS automatically detects the presence of SATA devices.

SATA Mode Selection
Determine how SATA controller(s) operate. Operation mode options are RAID Mode, IDE

Mode and AHCI Mode.

SATA Control Speed

Use this item to choose the SATA speed. Here are the options for your selection: Auto Gen1,
Gen2 and Gen3.

 PCH-FW Configuration

This screen shows the ME Firmware version, and its detail information.

eBOX670-883-FL Series User’s Manual

BIOS Setup Utility

37

 NCT6627UD Super IO Configuration

You can use this screen to select options for the Super IO Configuration, and change the
value of the selected option.

A description of the selected item appears on the right side of the screen. For items marked

with “”, please press <Enter> for more options.

Serial Port 1~6 Configuration

Use these items to set parameters of Serial Port 1~6.

eBOX670-883-FL Series User’s Manual

BIOS Setup Utility

38

 Serial Port 1 Configuration

Serial Port
Use this item to enable or disable serial port 1. The optimal setting for base I/O address is

3F8h and for interrupt request line is IRQ4.

Select Mode
Use this item to configure serial port 0. Here are the options for your selection:
RS232
RS422
RS485.

eBOX670-883-FL Series User’s Manual

BIOS Setup Utility

39

 Serial Port 2 Configuration

Serial Port
Use this item to enable or disable serial port 1. The optimal setting for base I/O address is

2F8h and for interrupt request line is IRQ3.

Select Mode
Use this item to configure serial port 0. Here are the options for your selection:
RS232
RS422
RS485.

eBOX670-883-FL Series User’s Manual

BIOS Setup Utility

40

 Serial Port 3 Configuration

Serial Port
Use this item to enable or disable serial port 1. The optimal setting for base I/O address is

3E8h and for interrupt request line is IRQ7.

Select Mode
Use this item to configure serial port 0. Here are the options for your selection:
RS232
RS422
RS485.

eBOX670-883-FL Series User’s Manual

BIOS Setup Utility

41

 Serial Port 4 Configuration

Serial Port
Use this item to enable or disable serial port 1. The optimal setting for base I/O address is

2E8h and for interrupt request line is IRQ5.

Select Mode
Use this item to configure serial port 0. Here are the options for your selection:
RS232
RS422
RS485.

eBOX670-883-FL Series User’s Manual

BIOS Setup Utility

42

 Serial Port 5 Configuration

Serial Port
Use this item to enable or disable serial port 1. The optimal setting for base I/O address is

2E0h and for interrupt request line is IRQ10.

Select Mode
Use this item to configure serial port 0. Here are the options for your selection:
RS232
RS422
RS485.

eBOX670-883-FL Series User’s Manual

BIOS Setup Utility

43

 Serial Port 6 Configuration

Serial Port
Use this item to enable or disable serial port 1. The optimal setting for base I/O address is

2F0h and for interrupt request line is IRQ6.

Select Mode
Use this item to configure serial port 0. Here are the options for your selection:
RS232
RS422
RS485.

eBOX670-883-FL Series User’s Manual

BIOS Setup Utility

44

4.3 Chipset Menu

The Chipset menu allows users to change the advanced chipset settings. You can select any
of the items in the left frame of the screen to go to the sub menus:

► PCH-IO Configuration
► System Agent (SA) Configuration

For items marked with “”, please press <Enter> for more options.

eBOX670-883-FL Series User’s Manual

BIOS Setup Utility

45

 PCH-IO Configuration

This screen shows memory information. For items marked with “”, please press <Enter> for

more options.

USB Configuration

XHCI Mode

Use this item to enable, disable or Auto mode for XHCI, it is one USB Spec compatible and
provide an interface to different hardware host controller implementations.

eBOX670-883-FL Series User’s Manual

BIOS Setup Utility

46

 System Agent (SA) Configuration

This screen provides function for specifying internal graphics controller and memory related
parameters.

Graphics Configuration

Internal Graphics

You can use this item to select internal graphics to enable or disable.

Graphics Control

Use this item for further setting of graphics control; we can get the following items to choose
your display interface, default is auto mode.

Primary IGFX Boot Display
Select the video device which will be activated during POST (Power-On Self Test).
This has no effect if external graphics present.

eBOX670-883-FL Series User’s Manual

BIOS Setup Utility

47

 Memory Configuration

Use this item for further setting of memory configuration, this screen displays memory
information, and allows user to set memory configuration.

eBOX670-883-FL Series User’s Manual

BIOS Setup Utility

48

4.4 Boot Menu

The Boot menu allows users to change boot options of the system.

Setup Prompt Timeout
Number of seconds to wait for setup activation key. 65535(0xFFFF) means indefinite waiting.

Boot Option Priorities
These are settings for boot priority. Specify the boot device priority sequence from the

available devices.

Hard Drive BBS Priorities
This item is for configuring the boot order for a specific device class. Its option(s) is only

visible if at least one device for this class is detected.

eBOX670-883-FL Series User’s Manual

BIOS Setup Utility

49

4.5 Security Menu

The Security menu allows users to change the security settings for the system.

Administrator Password
This item indicates whether an administrator password has been set (installed or uninstalled).

User Password

This item indicates whether an user password has been set (installed or uninstalled).

eBOX670-883-FL Series User’s Manual

BIOS Setup Utility

50

4.6 Save & Exit Menu

The Save & Exit menu allows users to load your system configuration with optimal or fail-safe
default values.

Save Changes and Exit

When you have completed the system configuration changes, select this option to leave Setup
and return to Main Menu. Select Save Changes and Exit from the Save & Exit menu and
press <Enter>. Select Yes to save changes and exit.

Discard Changes and Exit

Select this option to quit Setup without making any permanent changes to the system
configuration and return to Main Menu. Select Discard Changes and Exit from the Save & Exit
menu and press <Enter>. Select Yes to discard changes and exit.

Save Changes and Reset

When you have completed the system configuration changes, select this option to leave Setup
and reboot the computer so the new system configuration parameters can take effect. Select
Save Changes and Reset from the Save & Exit menu and press <Enter>. Select Yes to save
changes and reset.

Discard Changes and Reset

Select this option to quit Setup without making any permanent changes to the system
configuration and reboot the computer. Select Discard Changes and Reset from the Save &
Exit menu and press <Enter>. Select Yes to discard changes and reset.

eBOX670-883-FL Series User’s Manual

BIOS Setup Utility

51

Save Changes

When you have completed the system configuration changes, select this option to save
changes. Select Save Changes from the Save & Exit menu and press <Enter>. Select Yes to
save changes.

Discard Changes

Select this option to quit Setup without making any permanent changes to the system
configuration. Select Discard Changes from the Save & Exit menu and press <Enter>. Select
Yes to discard changes.

Restore Defaults

It automatically sets all Setup options to a complete set of default settings when you select this
option. Select Restore Defaults from the Save & Exit menu and press <Enter>.

Save as User Defaults

Select this option to save system configuration changes done so far as User Defaults. Select
Save as User Defaults from the Save & Exit menu and press <Enter>.

Restore User Defaults

It automatically sets all Setup options to a complete set of User Defaults when you select this
option. Select Restore User Defaults from the Save & Exit menu and press <Enter>.

Boot Override

Select a drive to immediately boot that device regardless of the current boot order.

Launch EFI Shell from filesystem device
Attempt to launch EFI Shell application (Shellx64.efi) from one of the available filesystem

devices.

eBOX670-883-FL Series User’s Manual

BIOS Setup Utility

52

This page is intentionally left blank.

eBOX670-883-FL Series User’s Manual

Watchdog Timer

53

APPENDIX A

WATCHDOG TIMER

About Watchdog Timer

Software stability is major issue in most application. Some embedded systems are not
watched by human for 24 hours. It is usually too slow to wait for someone to reboot when
computer hangs. The systems need to be able to reset automatically when things go wrong.
The watchdog timer gives us solution.

The watchdog timer is a counter that triggers a system reset when it counts down to zero from
a preset value. The software starts counter with an initial value and must reset it periodically. If
the counter ever reaches zero which means the software has crashed, the system will reboot.

eBOX670-883-FL Series User’s Manual

Watchdog Timer

54

Sample Program

Following is example to enable configuration by using debug tool.

 Enable WDT

1.Enable configuration

-O 2E 87

-O 2E 87

2. Select Logic device:

-O 2E 07

-O 2F 08

3. WDT Device Enable

-O 2E 30

-O 2F 01

5. Set timer unit

-O 2E F0

-O 2F 00  (00: Sec; 08: Minute)

4. Set base timer:

-O 2E F1

-O 2F 0A  Set Reset Time (Ex.0A:10 Sec)

 Disable WDT

1.Enable configuration

-O 2E 87

-O 2E 87

2. Select Logic device:

-O 2E 07

-O 2F 08

3. WDT Device Disable

-O 2E 30

-O 2F 00

eBOX670-883-FL Series User’s Manual

Programmable LED

55

APPENDIX B

PROGRAMMABLE LED

About Programmable LED

eBOX670-883-FL supports two programmable LED which allows user to program the LED
status. It can do as special indicator or alarm. Below is the way to program the LED.

Sample Code

1.Enable configuration

-O 2E 87

-O 2E 87

2. Select Logic device:

-O 2E 07

-O 2F 07

3. Enable GPIO 3x

-O 2E 30

-O 2F 08 -> Set Bit 4 to high.

4. Program Output Status

-O 2E ED

-O 2F 03 -> Set LEDs to light. ( Set Bit 0 & Bit 1 to high)

Note: The N has 8 bits. Only bit 0 and bit 1 are for programmable LED and bits 2

to 7 are for other function registers, so please don’ t set to this range to
cause unexpected issues.

eBOX670-883-FL Series User’s Manual

Programmable LED

56

This page is intentionally left blank.