AXIOMTEK eBOX635-881-FL-i7-4770TE, eBOX635-881-FL-G3320TE, eBOX635-881-FL-i5-4570TE, eBOX635-881-FL-i3-4330TE User Manual

eBOX635-881-FL Series

Embedded System

User’s Manual

ii

Disclaimers

This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third
party’s rights, and any liability arising from such use.

Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make any
commitment to update the information in this manual.

Axiomtek reserves the right to change or revise this document and/or product at any time
without notice

No part of this document may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written permission of Axiomtek Co., Ltd.

Copyright 2016 Axiomtek Co., Ltd.
All Rights Reserved
June 2016, Version A5
Printed in Taiwan

iii

Safety Precautions

Before getting started, please read the following important safety precautions.

1. The eBOX635-881-FL does not come equipped with an operating system. An operating
system must be loaded first before installing any software into the computer.

2. Be sure to ground yourself to prevent static charge when installing the internal
components. Use a grounding wrist strap and place all electronic components in any
static-shielded devices. Most electronic components are sensitive to static electrical
charge.

3. Disconnect the power cord from the eBOX635-881-FL before making any installation. Be
sure both the system and the external devices are turned OFF. Sudden surge of power
could ruin sensitive components. Make sure the eBOX635-881-FL is properly grounded.

4. Make sure the voltage of the power source is correct before connecting the equipment to
the power outlet.

5. Turn OFF the system power before cleaning. Clean the system using a cloth only. Do not
spray any liquid cleaner directly onto the screen.

6. Do not leave this equipment in an uncontrolled environment where the storage
temperature is below -40℃ or above 80℃. It may damage the equipment.

7. Do not open the system’s back cover. If opening the cover for maintenance is a must,
only a trained technician is allowed to do so. Integrated circuits on computer boards are
sensitive to static electricity. To avoid damaging chips from electrostatic discharge,
observe the following precautions:

 Before handling a board or integrated circuit, touch an unpainted portion of the

system unit chassis for a few seconds. This will help to discharge any static electricity
on your body.

 When handling boards and components, wear a wrist-grounding strap, available from

most electronic component stores.

Classification

1. Degree of production against electric shock : not classified

2. Degree of protection against the ingress of water : IP40

3. Equipment not suitable for use in the presence of a flammable anesthetic mixture with air
or with oxygen or nitrous oxide.

4. Mode of operation : Continuous

iv

General Cleaning Tips

You may need the following precautions before you begin to clean the computer. When you
clean any single part or component for the computer, please read and understand the details
below fully.

When you need to clean the device, please rub it with a piece of dry cloth.

1. Be cautious of the tiny removable components when you use a vacuum cleaner to
absorb the dirt on the floor.

2. Turn the system off before you start to clean up the component or computer.

3. Never drop the components inside the computer or get circuit board damp or wet.

4. Be cautious of all kinds of cleaning solvents or chemicals when you use it for the sake of
cleaning. Some individuals may be allergic to the ingredients.

5. Try not to put any food, drink or cigarette around the computer.

Cleaning Tools:

Although many companies have created products to help improve the process of cleaning
your computer and peripherals users can also use household items to clean their computers
and peripherals. Below is a listing of items you may need or want to use while cleaning your
computer or computer peripherals.

Keep in mind that some components in your computer may only be able to be cleaned using a
product designed for cleaning that component, if this is the case it will be mentioned in the
cleaning.

 Cloth: A piece of cloth is the best tool to use when rubbing up a component. Although

paper towels or tissues can be used on most hardware as well, we still recommend you
to rub it with a piece of cloth.

 Water or rubbing alcohol: You may moisten a piece of cloth a bit with some water or

rubbing alcohol and rub it on the computer. Unknown solvents may be harmful to the
plastics parts.

 Vacuum cleaner: Absorb the dust, dirt, hair, cigarette particles, and other particles out of

a computer can be one of the best methods of cleaning a computer. Over time these
items can restrict the airflow in a computer and cause circuitry to corrode.

 Cotton swabs: Cotton swaps moistened with rubbing alcohol or water are excellent tools

for wiping hard to reach areas in your keyboard, mouse, and other locations.

 Foam swabs: Whenever possible it is better to use lint free swabs such as foam swabs.

Note: We strongly recommended that you should shut down the system before you start

to clean any single components.

Please follow the steps below:

1. Close all application programs

2. Close operating software

3. Turn off power switch

4. Remove all device

5. Pull out power cable

v

Scrap Computer Recycling

If the computer equipments need the maintenance or are beyond repair, we strongly
recommended that you should inform your Axiomtek distributor as soon as possible for the
suitable solution. For the computers that are no longer useful or no longer working well, please
contact your Axiomtek distributor for recycling and we will make the proper arrangement.

Trademarks Acknowledgments

Axiomtek is a trademark of Axiomtek Co., Ltd.
IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines
Corporation.
Intel® , Core™ and Pentium® are registered trademarks of Intel Corporation.
MS-DOS and Microsoft® are trademarks of Microsoft Corporation.
Windows 7, Windows8, Windows 10, Windows 7 Embedded, Windows 8 Embedded,
Linux, MS-DOS, Microsoft® and other brand names and trademarks are the
properties and registered brands of their respective owners.

vi

Table of Contents

Disclaimers .............................................................................................................. ii

Safety Precautions ................................................................................................. iii

Classification .......................................................................................................... iii

General Cleaning Tips ........................................................................................... iv

Scrap Computer Recycling ..................................................................................... v

CHAPTER 1 INTRODUCTION ........................................................................ 1

1.1 General Description ............................................................................ 2

1.2 System Specifications ........................................................................ 3

1.2.1 CPU .................................................................................................................... 3

1.2.2 I/O System ......................................................................................................... 3

1.2.3 System Specification ........................................................................................ 3

1.2.4 Driver CD Content ............................................................................................. 4

1.3 Dimensions ......................................................................................... 5

1.3.1 System Dimension ............................................................................................ 5

1.3.2 Wall mount Dimension ..................................................................................... 6

1.4 I/O Outlets ........................................................................................... 7

1.5 Packing List ......................................................................................... 8

1.6 Model List ............................................................................................ 9

CHAPTER 2 HARDWARE INSTALLATION .................................................. 11

2.1 Installing the 2.5” SATA Device ....................................................... 11

2.2 Installing the Memory Module .......................................................... 12

2.3 Installing the CFast™ ....................................................................... 16

2.4 Installing the Express Mini Card ...................................................... 17

2.5 Installing CPU and PCH Thermal Pad .............................................. 19

CHAPTER 3 JUMPER SETTING & CONNECTORS .................................... 21

3.1 SBC Placement ................................................................................. 21

3.2 Jumper Settings and Connectors .................................................... 23

3.2.1 CMOS Clear Jumper (SJP2 on SBC87881) ................................................... 24

3.2.2 DC Power In Connector (SCN1) ..................................................................... 24

3.2.3 Digital Input Connector .................................................................................. 24

3.2.4 Digital Output Connector ............................................................................... 25

3.2.5 VGA Connector ............................................................................................... 26

3.2.6 DisplayPort Connector ................................................................................... 26

3.2.7 HDMI Connector (SCN6-SCN7) ...................................................................... 27

3.2.8 USB 3.0 Connector (SCN10) .......................................................................... 27

3.2.9 USB 2.0 Connector (SUSB1 and SUSB2)...................................................... 28

3.2.10 COM1~COM6 Serial Port Connector ............................................................. 28

3.2.11 Audio Connector ............................................................................................. 28

3.2.12 Ethernet Connector (LAN1~LAN2) ................................................................ 29

3.2.13 ATX Power On/OFF Button ............................................................................ 29

3.2.14 Reset Button .................................................................................................... 29

3.2.15 Remote Power Switch Connector (SPWRBT1) ............................................ 29

3.2.16 AT/ATX Switch................................................................................................. 30

vii

3.2.17 Serial ATA Connectors (SATA1-SATA2) ....................................................... 30

3.2.18 SIM Card Slots (SCN19).................................................................................. 30

3.2.19 CFast™ Socket ................................................................................................ 31

3.2.20 Half-Size Express Mini Card Slot (SCN13) ................................................... 32

3.2.21 Full-Size Express Mini Card (w/ SIM Slot)/ mSATA (SCN14) ...................... 33

3.2.22 Power Output Connector (SCN22, SCN26) ................................................... 34

CHAPTER 4 AMI BIOS SETUP UTILITY ...................................................... 35

4.1 Starting .............................................................................................. 35

4.2 Navigation Keys ................................................................................ 35

4.3 Main Menu ......................................................................................... 36

4.4 Advanced Menu ................................................................................. 37

4.5 Chipset Menu .................................................................................... 48

4.6 Boot Menu ......................................................................................... 52

4.7 Security Menu ................................................................................... 53

4.8 Save & Exit Menu .............................................................................. 54

APPENDIX WATCHDOG TIMER .................................................................. 57

About Watchdog Timer .................................................................................... 57

Assembler Sample Program ............................................................................ 58

viii

This page is intentionally left blank.

eBOX635-881-FL Series User’s Manual

Introduction

1

CHAPTER 1

INTRODUCTION

This chapter contains general information and detailed specifications of the eBOX635-881-FL.
The Chapter 1 includes the following sections:

 General Description
 System Specifications
 Dimensions
 I/O Outlets
 Packing List
 Model List

eBOX635-881-FL Series User’s Manual

Introduction

2

1.1 General Description

The eBOX635-881-FL is an embedded system that supports LGA1150 Socket 4th
generation Intel® Core™ i7/i5/i3/Celeron processor to support Windows 7, Windows
7 Embedded, Windows 8, Windows 8 Embedded Windows 10 or Linux, suitable for
the most endurable operation.

It features fan less design with full feature I/O, one 204-pin unbuffered SODIMM
socket for single channel DDR3-1333/1600 MHz memory, and enhanced system
dependability by built-in Watchdog Timer.

 Features

1. Intel

®

Haswell / Haswell-Refresh H81 Platform

2. Support LGA1150 Socket Intel® Core™ i7/i5/i3/Celeron processor

3. Maximum to 8GB DDR3 1333/1600 MHz memory

4. Compact and fan-less design

5. Supports 2 USB 3.0 ports and 4 USB 2.0 ports

6. Supports 6 jump-less RS-232/422/485

7. Supports 2 10/100/1000Mbps Ethernet ports

8. Supports ATX power switch with status indicator (AT/ATX mode selection)

9. 16 DI/DO (8 IN & 8 OUT)

10. Two HDMI

11. One DisplayPort

12. One VGA

13. One 2.5” SATA HDD drive bay

(Supports 9.5mm height HDD/SSD, power provides +5V to the drive only)

14. One front access CFast™

15. Watchdog timer

16. AC to 19V/12V DC adapter

17. Dual Express Mini Card slot with one SIM slot

18. Three Antenna openings

 Reliable and Stable Design

The eBOX635-881-FL adopts the advanced cooling system and supporting the CFast™,
which makes it especially suitable for vibration environments, best for industrial
automation, digital signage and gaming application.

 Embedded O.S. Supported

The eBOX635-881-FL not only supports Windows 7, Windows 8, Window 8.1, and
Windows 10, but also supports embedded OS, such as Windows 7 Embedded, Windows
8 Embedded and Linux.

 Various Storage devices supported

For storage device, the eBOX635-881-FL supports one 2.5" SATA storage drive bay,
mSATA and one CFast™ slot.

eBOX635-881-FL Series User’s Manual

Introduction

3

1.2 System Specifications

1.2.1 CPU

 CPU

 LGA1150 Socket Intel® Core™ i7/i5/i3/Celeron processor
 Working temperature depends on TDP of processor, please refer to 1.2.3

System Specification

 Chipset

 Intel® Haswell H81 chipset

 BIOS

 American Megatrends Inc. UEFI (Unified Extensible Firmware Interface)

BIOS.

 System Memory

 One 204-pin unbuffered DDR3 1333/1600MHz SO-DIMM socket, max. up

to 8GB

1.2.2 I/O System

 Six jumper-less RS-232/422/485. COM1~COM6 for full function 9-pin D-Sub male

connectors

 One VGA connector for display (Supports max resolution up to 1920x1200)
 One DisplayPort for display (Supports max resolution up to 2560x1600)
 Two HDMI for display (Supports HDMI 1.4a, max resolution up to 4K × 2K)
 Two Audio connectors (Mic-IN, Line-OUT)
 Two RJ-45 connectors for 10/100/1000Base-T Ethernet ports
 Two USB 3.0 connectors
 Four USB 2.0 connectors
 Eight Digital Input and Eight Digital Output for digital I/O 9-pin D-Sub female

connectors

 One 19/12V DC-IN Power Input connector
 One Indicator for HDD Active
 One Reset switch
 One AT/ATX switch
 One Power switch
 One Remote PWR switch

1.2.3 System Specification

 Watchdog Timer

 1~255 seconds or minutes; up to 255 levels.

 Power Supply

 19V/12V DC input connector

 Operation Temperature

 -20℃ ~50℃ (-4 ºF ~ 122ºF), with TDP 35W

 Storage Temperature

 -40℃ ~ 80℃ (-4 ºF ~ 176ºF)

 Humidity

 10% ~ 90% (non-condensation)

eBOX635-881-FL Series User’s Manual

Introduction

4

 Vibration Endurance

 3Grm w/ CFast™ (5-500Hz, X, Y, Z directions)

 Weight

 2.5 kg (5.51 lb) without package
 4.5 kg (9.92 lb) with package

 Dimensions

 280mm(11.02”) (W) x150mm(5.91”) (D) x 76mm(2.99”) (H)

1.2.4 Driver CD Content

 Driver

 Audio
 Chipset
 Ethernet
 Graphic
 Intel Rapid Storage Technology
 USB 3.0
 ME 9.0
 TPM

 Manual

 User Manual
 Quick Manual

Note: All specifications and images are subject to change without notice.

eBOX635-881-FL Series User’s Manual

Introduction

5

1.3 Dimensions

The following diagrams show you dimensions and outlines of the eBOX635-881-FL.

1.3.1 System Dimension

eBOX635-881-FL Series User’s Manual

Introduction

6

1.3.2 Wall mount Dimension

eBOX635-881-FL Series User’s Manual

Introduction

7

1.4 I/O Outlets

The following figures show you I/O outlets on front view of the eBOX635-881-FL.

 Front View drawing

Note: If you set AT/ATX switch to AT mode, the system will be automatically

power on without pressing soft power button during power input. If you set
AT/ATX switch to ATX mode, it is necessary to manually press soft power
button to power on the system.

 Rear View drawing

Power Button

Remote Switch

USB 2.0

COM1~COM6

(RS232/422/485)

Audio Connectors

LED

Indicator

AT/ATX Switch

Reset

DC Input- 19/12V

Antenna opening

Display Port

Gigabit Ethernet

LAN1/2

CFast™ slot

USB 2.0

VGA

Antenna opening

DI/DO

(8 IN & 8 OUT)

HDMI 1&2

USB 3.0

eBOX635-881-FL Series User’s Manual

Introduction

8

1.5 Packing List

The package bundled with your eBOX635-881-FL should contain the following items:

 eBOX635-881-FL System Unit x 1
 eBOX635-881-FL Quick Installation Guide x 1
 AC to 19/12V DC adapter (By selection)
 CD x 1 (For Driver and Manual)
 Screws Pack x1
 DRAM Thermal pad
 Spare parts: CPU, PCH of thermal pad
 Pre-install Intel Processor
 Pre-install Foot pad x4
 Optional DDR3 SODIMM
 Optional Wall-mount Brackets
 Optional Antenna
 Optional Mini Card Module
 Optional 2.5” SATA Storage
 Optional CFast™ Card
 Optional Power Cord

Note: If you can not find this package or any items are missing, please contact

Axiomtek distributors immediately.

eBOX635-881-FL Series User’s Manual

Introduction

9

1.6 Model List

eBOX635-881-FL-i7-4770TE

Fanless Embedded System with Intel Core i7-4770TE (4 Cores)

2.3G, max. up to 3.3G Processor, HDMIx2/VGA,DisplayPort,
GbE LAN*2, USB3.0*2, Audio, RS-232/422/485*6, DI*8/DO*8,

19/12V AC/DC Power Adapter

eBOX635-881-FL-i5-4570TE

Fanless Embedded System with Intel Core i5-4570TE (2 Cores)

2.3G, max. up to 3.3G Processor, HDMIx2/VGA, DisplayPort,
GbE LAN*2, USB3.0*2, Audio, RS-232/422/485*6, DI*8/DO*8,

19/12V AC/DC Power Adapter

eBOX635-881-FL-i3-4330TE

Fanless Embedded System with Intel Core i3-4330TE (2 Cores)

2.4G Processor, HDMIx2/VGA, DisplayPort, GbE LAN*2,
USB3.0*2, Audio, RS-232/422/485*6, DI*8/DO*8,19/12V AC/DC

Power Adapter

eBOX635-881-FL-G3320TE

Fanless Embedded System with Intel Pentium G3320TE (2
Cores) 2.3G Processor, HDMIx2/VGA, DisplayPort, GbE LAN*2,
USB3.0*2, Audio, RS-232/422/485*6, DI*8/DO*8,19/12V AC/DC

Power Adapter

If you cannot find this package or any items are missing, please contact Axiomtek distributors
immediately.

eBOX635-881-FL Series User’s Manual

Introduction

10

This page is intentionally left blank.

eBOX635-881-FL Series User’s Manual

Hardware Installation

11

CHAPTER 2

HARDWARE INSTALLATION

The eBOX635-881-FL is convenient for your various hardware configurations, such as HDD
(Hard Disk Drive), SSD (Solid State Drive) CFast™ card or PCI Express Mini Card modules.
The chapter 2 will show you how to install the hardware.

2.1 Installing the 2.5” SATA Device

Step 1 Turn off the system, and unplug the power cord.

Step 2 Turn the system upside down to locate screws at the Bottom, loosen screws.

Step 3 Remove the cover and then loosen four screws of 2.5” HDD drive bay.

Step 4 Assembly your 2.5” HDD/SSD into drive bay, fasten it with four screws.

eBOX635-881-FL Series User’s Manual

Hardware Installation

12

Step 5 Please refer to the following photo to connect SATA power and signal cables.

Step 6 Fasten screws of HDD drive bay.

2.2 Installing the Memory Module

Step 1 Turn off the system, and unplug the power cord.

Step 2 Turn the system upside down to locate screws at the Bottom, loosen screws.

Step 3 Remove the bottom cover to locate the bracket screws. Then loosen four

screws to take out the bracket directly.

eBOX635-881-FL Series User’s Manual

Hardware Installation

13

Step 4 You will see the DRAM slot under bracket

Step 5 Take out the thermal pad from accessory kit

Step 6 Remove transparent plastic Mylar from thermal pad, and stick the thermal

pad onto motherboard.

eBOX635-881-FL Series User’s Manual

Hardware Installation

14

Step 7 Locate the memory module, insert the gold colored contact into the socket,

and push the module down, until it is firmly seated by locking two latches on
the sides.

Step 8 Take 2nd thermal pad, remove the transparent plastic mylar and stick it onto

memory.

Step 9 Assembly the memory bracket and fasten all screws.

eBOX635-881-FL Series User’s Manual

Hardware Installation

15

Step 10 Assembly the Top Cover back and fasten all screws.

eBOX635-881-FL Series User’s Manual

Hardware Installation

16

2.3 Installing the CFast™

Step 1 Turn off the system, and unplug the power cord.

Step 2 Turn the system to the side with CFast™ cover.
Step 3 Loosen screws to remove the CFast™ cover.

Step 4 Slide CFast™ card into CFast™ slot with caution.

Step 5 Close the cover to the chassis, and fasten all screws.

eBOX635-881-FL Series User’s Manual

Hardware Installation

17

2.4 Installing the Express Mini Card

Step 1 Turn off the system, and unplug the power cord.

Step 2 Turn the system upside down to locate screws at the Bottom, loosen screws.

Step 3 Remove the bottom cover to locate the Express Mini Card slot.

eBOX635-881-FL Series User’s Manual

Hardware Installation

18

Step 4 Slide Mini Card into Mini Card slot with caution, and fasten screw of express

Mini Card.

Full Size Mini Card

Half Size Mini Card

Step 5 Assembly the Top Cover back and fasten all screws.

eBOX635-881-FL Series User’s Manual

Hardware Installation

19

2.5 Installing CPU and PCH Thermal Pad

The eBOX635-881-FL also offers two CPU & PCH thermal pad for spare parts, thus you

can get them from your accessory box. Please refer to the following information
to replace your thermal pad if original thermal pad is damaged.

Step 1 The main board of eBOX635-881-FL picture is showing as below, there are

CPU and PCH locations on bottom site.

Step 2 Please remove original thermal pad and set new one on CPU and PCH, you

can refer to below picture.

Note: We have installed thermal pad for eBOX635-881-FL already and this chapter

just to let you know how to replace new thermal pad by yourself. If any further
information is requested, please feel free to contact Axiomtek distributors or
FAE immediately.

eBOX635-881-FL Series User’s Manual

Hardware Installation

20

This page is intentionally left blank.

eBOX635-881-FL Series User’s Manual

Jumper Setting & Connectors

21

CHAPTER 3

JUMPER SETTING & CONNECTORS

Proper jumper settings configure the eBOX635-881-FL to meet your application purpose. We
are herewith listing a summary table of all jumpers and default settings for onboard devices,
respectively.

3.1 SBC Placement

SBC87881 Top Side

eBOX635-881-FL Series User’s Manual

Jumper Setting & Connector

22

SBC87881 Bottom Side

Note: We strongly recommended that you should not modify any unmentioned jumper

setting without Axiomtek FAE’s instruction. Any modification without instruction
might cause system to become damage.

eBOX635-881-FL Series User’s Manual

Jumper Setting & Connectors

23

3.2 Jumper Settings and Connectors

Connectors connect the system with other parts/devices. Loose or improper
connection might cause problems. Make sure all connectors are properly and firmly
connected. Below summary table shows you all connectors on the eBOX635-881-FL.

Jumper & Switch Setting

Section

CMOS Clear Jumper

3.2.1

External Connectors

Section

DC Power In Connector

3.2.2

Digital Input Connector

3.2.3

Digital Output Connector

3.2.4

VGA Connector

3.2.5

DisplayPort Connector

3.2.6

HDMI Connector

3.2.7

USB 3.0 Connector

3.2.8

USB 2.0 Connector

3.2.9

COM 1~6 Serial Port Connector

3.2.10

Audio Connector

3.2.11

Ethernet Connector

3.2.12

ATX Power On/Off Button

3.2.13

Reset Button

3.2.14

Remote Power Switch Connector

3.2.15

AT/ATX Switch

3.2.16

Internal Connectors

Section

Serial ATA Connectors

3.2.17

SIM Card Slot

3.2.18

CFast™ Socket

3.2.19

Half-Size Mini Card Slot

3.2.20

Full-Size Mini Card w/ SIM Slot/ mSATA

3.2.21

Power Output Connector

3.2.22

eBOX635-881-FL Series User’s Manual

Jumper Setting & Connector

24

3.2.1 CMOS Clear Jumper (SJP2 on SBC87881)

Function

Setting

Normal (Default)

1-2

Clear RTC

2-3

3.2.2 DC Power In Connector (SCN1)

The system supports a DC 19V power-din connector for system power input.

3.2.3 Digital Input Connector

The system is equipped with an 8-channel digital Input connector that meets
requirements for a system customary automation control. The digital I/O can be
configured to control cash drawers and sense warning signals from an Uninterrupted
Power System (UPS), or perform store security control. You may use software
programming to control these digital signals.

Pin

Signal

1

DI0 2 DI1 3 DI2 4 DI3 5 DI4

6

DI5

7

DI6 8 DI7

9

GND

Pin

Signal

1

GND

2

GND

3

DC 19V

4

DC 19V

eBOX635-881-FL Series User’s Manual

Jumper Setting & Connectors

25

Dry Contact Wiring

Wet Contact Wiring

3.2.4 Digital Output Connector

The system is equipped with an 8-channel digital output connector that meets
requirements for a system customary automation control. The digital I/O can be
configured to control cash drawers and sense warning signals from an Uninterrupted
Power System (UPS), or perform store security control. You may use software
programming to control these digital signals.

Pin

Signal

1

DO0 2 DO1 3 DO2 4 DO3 5 DO4

6

DO5

7

DO6 8 DO7

9

GND

DO Contact Wiring

eBOX635-881-FL Series User’s Manual

Jumper Setting & Connector

26

3.2.5 VGA Connector

The VGA connector is a slim type 15-pin D-Sub connector which is common for the
CRT VGA display. The VGA interface configuration can be configured via the
software utility.

3.2.6 DisplayPort Connector

DisplayPort interface is also called DP port.

Pin

Signal

1

DPB_LANE0

2

GND

3

DPB_LANE0#

4

DPB_LANE1

5

GND

6

DPB_LANE1#

7

DPB_LANE2

8

GND

9

DPB_LANE2#

10

DPB_LANE3

11

GND

12

DPB_LANE3#

13

Detect Pin

14

GND

15

DPB_AUX

16

GND

17

DPB_AUX#

18

DPB_HPDE

19

GND

20

+3.3V

eBOX635-881-FL Series User’s Manual

Jumper Setting & Connectors

27

3.2.7 HDMI Connector (SCN6-SCN7)

The HDMI (High-Definition Multimedia Interface) is a compact digital interface which is
capable of transmitting high-definition video and high-resolution audio over a single cable. Its
interface is available through connector SCN6 or SCN7.

Pin

Signal

Pin

Signal

1

HDMI OUT_DATA2+

11

GND

2

GND

12

HDMI OUT Clock-

3

HDMI OUT_DATA2-

13

N.C.

4

HDMI OUT_DATA1+

14

N.C.

5

GND

15

HDMI OUT_SCL

6

HDMI OUT_DATA1-

16

HDMI OUT_SDA

7

HDMI OUT_DATA0+

17

GND

8

GND

18

+5V

9

HDMI OUT_DATA0-

19

HDMI_HTPLG

10

HDMI OUT Clock+

3.2.8 USB 3.0 Connector (SCN10)

The Universal Serial Bus connectors are compliant with USB 3.0 (5Gb/s), and ideally
for installing USB peripherals such as keyboard, mouse, scanner, etc.

Pin

Signal USB Port 0

Pin

Signal USB Port 1

1

USB_VCC (+5V level
standby power)

10

USB_VCC (+5V level standby
power)

2

USB_Data2-

11

USB_Data3-

3

USB_Data2+

12

USB_Data3+

4

GND

13

GND

5

SSRX2-

14

SSRX3-

6

SSRX2+

15

SSRX3+

7

GND

16

GND

8

SSTX2-

17

SSTX3-

9

SSTX2+

18

SSTX3+

eBOX635-881-FL Series User’s Manual

Jumper Setting & Connector

28

3.2.9 USB 2.0 Connector (SUSB1 and SUSB2)

The Universal Serial Bus connectors are compliant with USB 2.0 (480Mbps), and
ideally for installing USB peripherals such as keyboard, mouse, scanner, etc.

SUSB1 carries USB port 1and 2.
SUSB2 carries USB port 3and 4.

1 2 3 4

5 6 7 8

3.2.10 COM1~COM6 Serial Port Connector

The system has six serial ports. COM1~COM6 are RS-232/422/485 ports. Please
refer to Chapter 3 for the detail of BIOS setting.

Pin

RS-232

RS-422

RS-485

COM1~COM6

1

DCD, Data Carrier Detect

TX-

Data-

2

RXD, Receive Data

TX+

Data+

3

TXD, Transmit Data

RX+

No use

4

DTR, Data Terminal Ready

RX-

No use

5

GND, Ground

No use

No use

6

DSR, Data Set Ready

No use

No use

7

RTS, Request To Send

No use

No use

8

CTS, Clear To Send

No use

No use

9

RI, Ring Indicator

No use

No use

3.2.11 Audio Connector

These two audio jacks ideal are for Audio Mic-In and Audio Line-out.

Pin

Signal

1

Microphone In

2

Line Out

Pin

Signal

Pin

Signal

1

USB VCC (+5V
leve standby
powerl)

5

USB VCC (+5V
level standby
power)

2

USB _D-

6

USB _D-

3

USB _D+

7

USB _D+

4

GND

8

GND

eBOX635-881-FL Series User’s Manual

Jumper Setting & Connectors

29

3.2.12 Ethernet Connector (LAN1~LAN2)

The RJ-45 connector is for Ethernet. To connect the board to a 1000/100/10 Base-T hub, just
plug one end of the cable into connector and connect the other end (phone jack) to a
1000/100/10-Base-T hub.

Pin

Signal

Pin

Signal

L1L2L3L4L5L6L7L8

A B

A B

L1

MDI0+

L5

MDI2-

L2

MDI0-

L6

MDI1-

L3

MDI1+

L7

MDI3+

L4

MDI2+

L8

MDI3-

A

Active LED (Yellow)

B

100 LAN LED (Green)/ 1000 LAN LED (Orange)

3.2.13 ATX Power On/OFF Button

The ATX power button is on the I/O side. It can allow users to control eBOX635-881­FL power on/off.

Function

Description

On

Turn on/off system

Off

Keep system status

3.2.14 Reset Button

The Reset button can allow users to reset eBOX635-881-FL.

Function

Description

On

Reset system

Off

Keep system status

3.2.15 Remote Power Switch Connector (SPWRBT1)

One 2-pin connector output for remote power on/off switch.

Function

Description

Short(1-2)

Turn on/off system

Open

Keep system status

eBOX635-881-FL Series User’s Manual

Jumper Setting & Connector

30

3.2.16 AT/ATX Switch

If you set AT/ATX switch to AT mode, the system will be automatically power on without
pressing soft power button during power input; we can use this switch to achieve auto power
on demand.

3.2.17 Serial ATA Connectors (SATA1-SATA2)

These Serial Advanced Technology Attachment (Serial ATA or SATA) connectors are for
high-speed SATA interfaces. They are computer bus interfaces for connecting to devices such
as hard disk drives. This board has two SATA 3.0 ports with 6Gb/s performance.

The sata power cable provides +5V, and ground to the drive only.

3.2.18 SIM Card Slots (SCN19)

eBOX635-881-FL includes one SIM slots on the bottom side of the system for inserting
SIM Card. It is mainly used in 3G wireless network application.

Pin

Signal

1

GND

2

SATA_TX+

3

SATA_TX-

4

GND

5

SATA_RX-

6

SATA_RX+

7

GND

Pin

Signal

1

PWR

2

RST

3

CLK

4

NC 5 GND

6

VPP

7

I/O 8 NC

eBOX635-881-FL Series User’s Manual

Jumper Setting & Connectors

31

3.2.19 CFast™ Socket

The system is equipped with a CFast™ socket on the bottom side to support a CFast™ card
which is based on the Serial ATA bus. The socket is specially designed to avoid incorrect
installation of the CFast™ card. When installing or removing the CFast™ card, please make
sure the system power is off. The CFast™ card by default identifies itself as C: or D: drive in
your PC system.

Pin

Signal

Pin

Signal

S1

GND

PC1

NC

S2

TX+

PC2

GND

S3

TX-

PC3

NC

S4

GND

PC4

NC

S5

RX-

PC5

NC

S6

RX+

PC6

NC

S7

GND

PC7

GND

PC8

NC

PC9

NC

PC10

NC

PC11

NC

PC12

NC

PC13

3.3V

PC14

3.3V

PC15

GND

PC16

GND

PC17

NC

eBOX635-881-FL Series User’s Manual

Jumper Setting & Connector

32

3.2.20 Half-Size Express Mini Card Slot (SCN13)

PCI Express Mini Card connector supports a PCI Express x1 link and a USB 2.0 link. A PCI
Express Mini Card can be applied to either PCI Express or USB 2.0. It complies with PCI­Express Mini Card Spec. V1.2.

Pin

Signal

Pin

Signal

1

WAKE#

2

+3.3VSB

3

No use

4

GND

5

No use

6

+1.5V

7

CLKREQ#

8

No use

9

GND

10

No use

11

REFCLK-

12

No use

13

REFCLK+

14

No use

15

GND

16

No use

17

No use

18

GND

19

No use

20

W_DISABLE#

21

GND

22

PERST#

23

PE_RXN3

24

+3.3VSB

25

PE_RXP3

26

GND

27

GND

28

+1.5V

29

GND

30

SMB_CLK

31

PE_TXN3

32

SMB_DATA

33

PE_TXP3

34

GND

35

GND

36

USB_D8-

37

GND

38

USB_D8+

39

+3.3VSB

40

GND

41

+3.3VSB

42

No use

43

GND

44

No use

45

No use

46

No use

47

No use

48

+1.5V

49

No use

50

GND

51

No use

52

+3.3VSB

eBOX635-881-FL Series User’s Manual

Jumper Setting & Connectors

33

3.2.21 Full-Size Express Mini Card (w/ SIM Slot)/ mSATA (SCN14)

You may need to adjust the BIOS setting to select mSATA or Mini card PCI-E interface.
This is a PCI-Express Mini Card connector which supports PCI-Express x1 link, SATA link ,

USB 2.0 link and 3G wireless network application(SCN19). A PCI-Express Mini Card can be
applied to either PCI-Express or USB 2.0 or SATA. It complies with PCI-Express Mini Card
Spec. V1.2.

Pin

Signal

Pin

Signal

1

WAKE#

2

+3.3VSB

3

No use

4

GND

5

No use

6

+1.5V

7

CLKREQ#

8

UIM_PWR

9

GND

10

UIM_DATA

11

REFCLK-

12

UIM_CLK

13

REFCLK+

14

UIM_RESET

15

GND

16

UIM_VPP

17

No use

18

GND

19

No use

20

W_DISABLE#

21

GND

22

PERST#

23

PE_RXN4/
SATA4_RXP

24

+3.3VSB

25

PE_RXP4/
SATA4_RXN

26

GND

27

GND

28

+1.5V

29

GND

30

SMB_CLK

31

PE_TXN4/
SATA4_TXN

32

SMB_DATA

33

PE_TXP4/
SATA4_TXP

34

GND

35

GND

36

USB #10_D-

37

GND

38

USB #10_D+

39

+3.3VSB

40

GND

41

+3.3VSB

42

No use

43

GND

44

No use

45

No use

46

No use

47

No use

48

+1.5V

49

No use

50

GND

51

No use

52

+3.3VSB

eBOX635-881-FL Series User’s Manual

Jumper Setting & Connector

34

3.2.22 Power Output Connector (SCN22, SCN26)

Pin

Signal

1

+12V level

2

GND

3

GND

4

+5V level

eBOX635-881-FL Series User’s Manual

AMI BIOS Setup Utility 35

CHAPTER 4

AMI BIOS SETUP UTILITY

The AMI BIOS provides users with a built-in setup program to modify basic system
configuration. All configured parameters are stored in a battery-backed CMOS to save the
setup information whenever the power is turned off. This chapter provides users with detailed
description about how to set up basic system configuration through the AMI BIOS setup utility.

4.1 Starting

To enter the setup screens, follow the steps below:

1. Turn on the computer and press the <Del> key immediately.

2. After you press the <Del> key, the main BIOS setup menu displays. You can access the

other setup screens from the main BIOS setup menu, such as the Advanced and
Chipset menus.

It is strongly recommended that you should avoid changing the chipset’s defaults. Both AMI
and your system manufacturer have carefully set up these defaults that provide the best
performance and reliability.

4.2 Navigation Keys

The BIOS setup/utility uses a key-based navigation system called hot keys. Most of the BIOS
setup utility hot keys can be used at any time during the setup navigation process. These keys
include <F1>, <F2>, <Enter>, <ESC>, <Arrow> keys, and so on.

Note: Some of the navigation keys differ from one screen to another.

Hot Keys

Description

 Left/Right

The Left and Right <Arrow> keys allow you to select a setup screen.

 Up/Down

The Up and Down <Arrow> keys allow you to select a setup screen or sub­screen.

+ Plus/Minus

The Plus and Minus <Arrow> keys allow you to change the field value of a
particular setup item.

Tab

The <Tab> key allows you to select setup fields.

F1

The <F1> key allows you to display the General Help screen.

F2

The <F2> key allows you to Load Previous Values.

F3

The <F3> key allows you to Load Optimized Defaults.

F4

The <F4> key allows you to save any changes you have made and exit
Setup. Press the <F4> key to save your changes.

Esc

The <Esc> key allows you to discard any changes you have made and exit
the Setup. Press the <Esc> key to exit the setup without saving your
changes.

Enter

The <Enter> key allows you to display or change the setup option listed for
a particular setup item. The <Enter> key can also allow you to display the
setup sub- screens.

eBOX635-881-FL Series User’s Manual

36 AMI BIOS Setup Utility

4.3 Main Menu

When you first enter the setup utility, you will enter the Main setup screen. You can always
return to the Main setup screen by selecting the Main tab. System Time/Date can be set up as
described below. The Main BIOS setup screen is shown below.

 System Date/Time

Use this option to change the system time and date. Highlight System Time or System Date
using the <Arrow> keys. Enter new values through the keyboard. Press the <Tab> key or the
<Arrow> keys to move between fields. The date must be entered in MM/DD/YY format. The
time is entered in HH:MM:SS format.

eBOX635-881-FL Series User’s Manual

AMI BIOS Setup Utility 37

4.4 Advanced Menu

 mSATA/PCIE select

Use this item to select the SCN14 to mSATA or Mini-PCIE mode.

 Launch PXE OpROM

Use this item to enable or disable the boot ROM function of the onboard LAN chip when the
system boots up.

The Advanced menu also allows users to set configuration of the CPU and other system
devices. You can select any of the items in the left frame of the screen to go to the sub menus:

► ACPI Settings
► CPU Configuration
► SATA Configuration
► PCH-FW Configuration
► NCT6106D Super IO Configuration

For items marked with “”, please press <Enter> for more options.

eBOX635-881-FL Series User’s Manual

38 AMI BIOS Setup Utility

 ACPI Settings

You can use this screen to select options for the ACPI configuration, and change the value of
the selected option. A description of the selected item appears on the right side of the screen.

ACPI Sleep State

Allow you to select the Advanced Configuration and Power Interface (ACPI) sleep
state. Here are the options for your selection: Suspend Dissabled and S3 (Suspend to
RAM). The S3 (Suspend to RAM) option selects the highest ACPI sleep state the
system will enter when SUSPEND button is pressed.

S3 Video Repost

Determine whether to invoke VGA BIOS POST on S3/STR resume.
[Disabled] When set to [No], the system will not invoke VGA BIOS POST on S3/STR
resume.
[Enabled] When set to [Yes], the system invokes VGA BIOS POST on S3/STR
resume.

eBOX635-881-FL Series User’s Manual

AMI BIOS Setup Utility 39

 CPU Configuration

This screen shows the CPU Configuration, and you can change the value of the selected
option.

Intel Virtualization Technology

Allow you to enable or disable Intel Virtualization Technology. When enabled, a VMM
can utilize the additional hardware capabilities provided by Vanderpool Technology .

eBOX635-881-FL Series User’s Manual

40 AMI BIOS Setup Utility

 SATA Configuration

In the SATA Configuration menu, you can see the currently installed hardware in the SATA
ports. During system boot up, the BIOS automatically detects the presence of SATA devices.

SATA Mode Selection

Use this item to choose the SATA operation mode. Here are the options for your
selection: IDE Mode and AHCI Mode.

SATA Controller Speed

Use this item to choose the SATA speed. Here are the options for your selection: Auto
Gen1, Gen2 and Gen3.

eBOX635-881-FL Series User’s Manual

AMI BIOS Setup Utility 41

 PCH-FW Configuration

This screen shows the ME Firmware version, and its detail information.

 NCT6106D Super IO Configuration

You can use this screen to select options for the Super IO Configuration, and change the
value of the selected option. A description of the selected item appears on the right side of the
screen. For items marked with “”, please press <Enter> for more options.

eBOX635-881-FL Series User’s Manual

42 AMI BIOS Setup Utility

Serial Port 1 Configuration

Serial Port

Use this item to enable or disable serial port 1. The optimal setting for base I/O
address is 3F8h and for interrupt request line is IRQ4.

Change Settings
Here are the options for your selection;

Auto;
IO=3F8h; IRQ=4;
IO=3F8h; IRQ=3,4,5,6,7,10,11,12;
IO=2F8h; IRQ=3,4,5,6,7,10,11,12;
IO=3E8h; IRQ=3,4,5,6,7,10,11,12;
IO=2E8h; IRQ=3,4,5,6,7,10,11,12;

Transmission Mode
Use this item to configure serial port 0. Here are the options for your selection:

RS232
RS422
RS485.

eBOX635-881-FL Series User’s Manual

AMI BIOS Setup Utility 43

 Serial Port 2 Configuration

Serial Port
Use this item to enable or disable serial port 2. The optimal setting for base I/O
address is 2F8h and for interrupt request line is IRQ3.

Change Settings
Here are the options for your selection;

Auto;
IO=2F8h; IRQ=3;
IO=3F8h; IRQ=3,4,5,6,7,10,11,12;
IO=2F8h; IRQ=3,4,5,6,7,10,11,12;
IO=3E8h; IRQ=3,4,5,6,7,10,11,12;
IO=2E8h; IRQ=3,4,5,6,7,10,11,12;

Transmission Mode
Use this item to configure serial port 0. Here are the options for your selection:

RS232
RS422
RS485.

eBOX635-881-FL Series User’s Manual

44 AMI BIOS Setup Utility

 Serial Port 3 Configuration

Serial Port
Use this item to enable or disable serial port 3. The optimal setting for base I/O
address is 3E8h and for interrupt request line is IRQ7.

Change Settings
Here are the options for your selection;

Auto;
IO=3E8h; IRQ=7;
IO=3E8h; IRQ=3,4,5,6,7,10,11,12;
IO=2E8h; IRQ=3,4,5,6,7,10,11,12;
IO=2E0h; IRQ=3,4,5,6,7,10,11,12;
IO=2F0h; IRQ=3,4,5,6,7,10,11,12;

Transmission Mode
Use this item to configure serial port 0. Here are the options for your selection:

RS232
RS422
RS485.

eBOX635-881-FL Series User’s Manual

AMI BIOS Setup Utility 45

 Serial Port 4 Configuration

Serial Port
Use this item to enable or disable serial port 4. The optimal setting for base I/O
address is 2E8h and for interrupt request line is IRQ5.

Change Settings
Here are the options for your selection;

Auto;
IO=2E8h; IRQ=7;
IO=3E8h; IRQ=3,4,5,6,7,10,11,12;
IO=2E8h; IRQ=3,4,5,6,7,10,11,12;
IO=2E0h; IRQ=3,4,5,6,7,10,11,12;
IO=2F0h; IRQ=3,4,5,6,7,10,11,12;

Transmission Mode
Use this item to configure serial port 0. Here are the options for your selection:

RS232
RS422
RS485.

eBOX635-881-FL Series User’s Manual

46 AMI BIOS Setup Utility

 Serial Port 5 Configuration

Serial Port
Use this item to enable or disable serial port 5. The optimal setting for base I/O
address is 2E0h and for interrupt request line is IRQ10.

Change Settings
Here are the options for your selection;

Auto;
IO=2E0h; IRQ=10;
IO=3E8h; IRQ=3,4,5,6,7,10,11,12;
IO=2E8h; IRQ=3,4,5,6,7,10,11,12;
IO=2E0h; IRQ=3,4,5,6,7,10,11,12;
IO=2F0h; IRQ=3,4,5,6,7,10,11,12;

Transmission Mode
Use this item to configure serial port 0. Here are the options for your selection:

RS232
RS422
RS485.

eBOX635-881-FL Series User’s Manual

AMI BIOS Setup Utility 47

 Serial Port 6 Configuration

Serial Port
Use this item to enable or disable serial port 6. The optimal setting for base I/O
address is 2F0h and for interrupt request line is IRQ6.

Change Settings
Here are the options for your selection;

Auto;
IO=2F0h; IRQ=10;
IO=3E8h; IRQ=3,4,5,6,7,10,11,12;
IO=2E8h; IRQ=3,4,5,6,7,10,11,12;
IO=2E0h; IRQ=3,4,5,6,7,10,11,12;
IO=2F0h; IRQ=3,4,5,6,7,10,11,12;

Transmission Mode
Use this item to configure serial port 0. Here are the options for your selection:

RS232
RS422
RS485.

eBOX635-881-FL Series User’s Manual

48 AMI BIOS Setup Utility

4.5 Chipset Menu

The Chipset menu allows users to change the advanced chipset settings. You can select any
of the items in the left frame of the screen to go to the sub menus:

► PCH - IO Configuration
► System Agent (SA) Configuration

For items marked with “”, please press <Enter> for more options.

eBOX635-881-FL Series User’s Manual

AMI BIOS Setup Utility 49

 PCH - IO Configuration

This screen allows users to configure PCH – IO Configuration parameters. For items marked
with “”, please press <Enter> for more options.

USB Configuration

Use this item for further setting of USB configuration.

eBOX635-881-FL Series User’s Manual

50 AMI BIOS Setup Utility

 System Agent (SA) Configuration

This screen allows users to configure System Agent (SA) parameters. For items marked with
“”, please press <Enter> for more options.

 Graphics Configuration

Use this item for further setting of graphics configuration.

Internal Graphics

You can use this item to select internal graphics to enable or disable.

Graphics Control

Use this item for further setting of graphics control; we can get the following items to
choose your display interface, default is auto mode.

eBOX635-881-FL Series User’s Manual

AMI BIOS Setup Utility 51

Primary IGFX Boot Display
Select the video device which will be activated during POST (Power-On Self Test).
This has no effect if external graphics present.

 Memory Configuration

Use this item for further setting of memory configuration, this screen displays memory
information, and allows user to set memory configuration.

eBOX635-881-FL Series User’s Manual

52 AMI BIOS Setup Utility

4.6 Boot Menu

The Boot menu allows users to change boot options of the system.

 Setup Prompt Timeout

Number of seconds to wait for setup activation key. 65535(0xFFFF) means indefinite waiting.

 Bootup NumLock State

Use this item to select the power-on state for the NumLock.

 Quiet Boot

Enable or disable Quiet Boot option.

 Boot Option Priorities

These are settings for boot priority. Specify the boot device priority sequence from the
available devices.

eBOX635-881-FL Series User’s Manual

AMI BIOS Setup Utility 53

4.7 Security Menu

The Security menu allows users to change the security settings for the system.

 Administrator Password

This item indicates whether an administrator password has been set (installed or uninstalled).

 User Password

This item indicates whether an user password has been set (installed or uninstalled).

eBOX635-881-FL Series User’s Manual

54 AMI BIOS Setup Utility

4.8 Save & Exit Menu

The Save & Exit menu allows users to load your system configuration with optimal or fail-safe
default values.

Save Changes and Exit

When you have completed the system configuration changes, select this option to
leave Setup and return to Main Menu. Select Save Changes and Exit from the Save &
Exit menu and press <Enter>. Select Yes to save changes and exit.

Discard Changes and Exit

Select this option to quit Setup without making any permanent changes to the system
configuration and return to Main Menu. Select Discard Changes and Exit from the
Save & Exit menu and press <Enter>. Select Yes to discard changes and exit.

Save Changes and Reset

When you have completed the system configuration changes, select this option to
leave Setup and reboot the computer so the new system configuration parameters
can take effect. Select Save Changes and Reset from the Save & Exit menu and
press <Enter>. Select Yes to save changes and reset.

Discard Changes and Reset

Select this option to quit Setup without making any permanent changes to the system
configuration and reboot the computer. Select Discard Changes and Reset from the
Save & Exit menu and press <Enter>. Select Yes to discard changes and reset.

Save Changes

When you have completed the system configuration changes, select this option to
save changes. Select Save Changes from the Save & Exit menu and press <Enter>.
Select Yes to save changes.

eBOX635-881-FL Series User’s Manual

AMI BIOS Setup Utility 55

Discard Changes

Select this option to quit Setup without making any permanent changes to the system
configuration. Select Discard Changes from the Save & Exit menu and press <Enter>.
Select Yes to discard changes.

Restore Defaults

It automatically sets all Setup options to a complete set of default settings when you
select this option. Select Restore Defaults from the Save & Exit menu and press
<Enter>.

Save as User Defaults

Select this option to save system configuration changes done so far as User Defaults.
Select Save as User Defaults from the Save & Exit menu and press <Enter>.

Restore User Defaults

It automatically sets all Setup options to a complete set of User Defaults when you
select this option. Select Restore User Defaults from the Save & Exit menu and press
<Enter>.

Boot Override

Select a drive to immediately boot that device regardless of the current boot order.

eBOX635-881-FL Series User’s Manual

56 AMI BIOS Setup Utility

This page is intentionally left blank.

eBOX635-881-FL Series User’s Manual

Watchdog Timer

57

APPENDIX

WATCHDOG TIMER

About Watchdog Timer

Software stability is major issue in most application. Some embedded systems are not
watched by human for 24 hours. It is usually too slow to wait for someone to reboot when
computer hangs. The systems need to be able to reset automatically when things go wrong.
The watchdog timer gives us solution.

The watchdog timer is a counter that triggers a system reset when it counts down to zero from
a preset value. The software starts counter with an initial value and must reset it periodically. If
the counter ever reaches zero which means the software has crashed, the system will reboot.

eBOX635-881-FL Series User’s Manual

Watchdog Timer

58

Assembler Sample Program

Following is example to enable configuration by using debug tool.

 Enable WDT

1.Enable configuration

-O 2E 87

-O 2E 87

2. Select Logic device:

-O 2E 07

-O 2F 08

3. WDT Device Enable

-O 2E 30

-O 2F 01

5. Set timer unit

-O 2E F0

-O 2F 00  (00: Sec; 08: Minute)

4. Set base timer:

-O 2E F1

-O 2F 0A  Set Reset Time (Ex.0A:10 Sec)

 Disable WDT

1.Enable configuration

-O 2E 87

-O 2E 87

2. Select Logic device:

-O 2E 07

-O 2F 08

3. WDT Device Disable

-O 2E 30

-O 2F 00