AXIOMTEK DK1211C User Manual

DK1211C User Guide
1
DK1211C
12.1" Industrial Display Module Kit
DK1211C User Guide
2
Disclaimers
This manual has been carefully checked and believed to contain accurate information. Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third party’s rights, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information in this document. Axiomtek does not make any commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Axiomtek Co., Ltd.
Copyright 2017 Axiomtek Co., Ltd.
All Rights Reserved
September 2017, Version A1
Printed in Taiwan
DK1211C User Guide
3
Safety Precautions
Before getting started, read the following important cautions.
1. Be sure to ground yourself to prevent static charge when installing the internal
components. Use a grounding wrist strap and place all electronic components in any static-shielded devices. Most electronic components are sensitive to static electrical charge.
2. Disconnect the power cords before making any installation. Be sure both the system
and the external devices are turned OFF. Sudden surge of power could ruin sensitive components.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
Windows® is a trademark of Microsoft Corporation.
IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation.
Intel® and Pentium® are trademarks of Intel Corporation.
AMI is trademark of American Megatrend Inc.
Other brand names and trademarks are the properties and registered brands of their respective owners.
DK1211C User Guide
4
Table of Contents
Disclaimers ..........................................................................................................2
Safety Precautions ...............................................................................................3
Chapter 1 Introduction ..................................................................... 5
1.1 General Description .....................................................................................5
1.2 Display Characteristics .................................................................................6
1.3 Absolute Maximum Ratings .........................................................................6
1.4 Block Diagram ..............................................................................................8
1.5 Mechanical Dimensions ...............................................................................9
Chapter 2 Electrical Characteristics ................................................. 12
2.1 TFT LCD Module ......................................................................................... 12
2.2 LED CONVERTER ......................................................................................... 14
2.3 The Input Data Format ............................................................................... 15
2.4 Optical Characteristics ................................................................................ 16
2.5 Interface Timing ......................................................................................... 19
2.6 Power On/Off Sequence ............................................................................. 20
Chapter 3 Input Terminal Pin Assignments ...................................... 21
3.1 TFT LCD Module Interface .......................................................................... 21
3.2 Backlight Unit............................................................................................. 23
Chapter 4 Touch Screen .................................................................. 25
4.1 Touch Characteristics.................................................................................. 25
4.2 Absolute Maximum Ratings ....................................................................... 25
4.3 Electrical Characteristics ............................................................................. 26
4.4 Touch Pin Assignment ................................................................................ 27
Appendix A Hanling Precaution ......................................................... 29
DK1211C User Guide
5
Chapter 1
Introduction
1.1 General Description
The DK1211C is a 12.1” TFT-LCD module with a white LED Backlight Unit and 1ch-LVDS interface. This module supports 800 x 600 SVGA MVA mode and displays 262K/ 16.2M colors and adopt projected capacitive touch. The converter for the LED Backlight Unit is built in.
DK1211C User Guide
6
1.2 Display Characteristics
Item
Specifications
Unit
Active Area
246.00 (W) x 184.50 (H)
mm
Outline Dimension
260.50(W) × 204.00(H) × 8.40(D)
mm
Pixels H x V
800 x 600
-
Pixel Pitch
0.3075× 0.3075
mm
Display Colors
262K / 16.2M
color
White Luminance
450 (TYP)
cd/m2
Contrast Ratio
1500: 1 (TYP)
-
Display Mode
Normally black
-
Surface Treatment
Anti-glare, Hardness 3H
-
Power Consumption
7.9 (TYP)
W
1.3 Absolute Maximum Ratings
1.3.1 Absolute Environmental Ratings
Item
Symbol
Min.
Max.
Unit
Note
Operating Temperature
T
OP
-30
85
°C Storage Temperature
T
ST
-30
85
°C
Note (1): Temperature and relative humidity range is shown in the figure below.
Note (2): 90 %RH Max. (Ta 40 ºC).
Note (3): Wet-bulb temperature should be 39 ºC Max. (Ta > 40 ºC).
DK1211C User Guide
7
Note (4): No condensation.
1.3.2 Electrical Absolute Ratings
1.3.2.1 TFT LCD MODULE
Item
Symbol
Min.
Max.
Unit
Remark
Power Supply Voltage
V
cc
-0.3 7 V
(1)
1.3.2.2 LED CONVERTER
Item
Symbol
Min.
Max.
Unit
Remark
Converter Voltage
Vi -0.3
18 V (1)(2)
Enable Voltage
EN - 5.5 V
Backlight Adjust
ADJ - 5.5 V
Note (1): Permanent damage to the device may occur if maximum values are exceeded.
Function operation should be restricted to the conditions described under Normal Operating Conditions.
Note (2): Specified values are for lamp (Refer to 3.2 for further information).
DK1211C User Guide
8
1.4 Block Diagram
DK1211C User Guide
9
1.5 Mechanical Dimensions
1.5.1 Outline Drawing (Front Side)
DK1211C User Guide
10
1.5.2 Outline Drawing (Back Side)
DK1211C User Guide
11
This page is intentionally left blank
DK1211C User Guide
12
Chapter 2
Electrical Characteristics
2.1 TFT LCD Module
Ta = 25 ± 2 ºC
Item
Symbol
Min.
Typ.
Max.
Unit
Condition
Power Supply Voltage
VCC
3.0
3.3
3.6 V at VCC=3.3V
4.75
5.0
5.25 V at VCC=5.0V
Rush Current
IRUSH
- - 1.5 A (2), at VCC=5.0V
Power Supply Current
White
-
450
540
mA
(3) a, at VCC=3.3V,
60Hz
-
310
370
mA
(3) a, at VCC=5.0V,
60Hz
Black
-
420
480
mA
(3) b, at VCC=3.3V,
60Hz
-
280
335
mA
(3) b, at VCC=5.0V,
60Hz
Power Consumption
PL
-
1.49
1.78
W
VCC=3.3V, 60Hz,
White Pattern
LVDS differential input voltage
|VID|
100 - 600
mV
LVDS common input voltage
VICM
0.7 - 1.6
V
DK1211C User Guide
13
Note (1) The module is recommended to operate within specification ranges listed above for
normal function.
Note (2) Measurement Conditions:
Note (3) The specified power supply current is under the conditions at Ta = 25 ± 2 ºC, fv = 60
Hz, whereas a power dissipation check pattern below is displayed.
DK1211C User Guide
14
2.2 LED CONVERTER
Ta = 25 ± 2 ºC
Item
Symbol
Min.
Typ.
Max.
Unit
Condition
Converter Power Supply Voltage
Vi 10.8
12.0
13.2 V (Duty 100%)
Converter Power Supply Current
Ii -
0.53 - A
@ Vi = 12V
(Duty 100%)
Converter Power Consumption
Pi - 6.4 - W
@ Vi = 12V
(Duty 100%)
EN Control Level
Backlig
ht on
2.0
3.3
5.0
V
Backlig
ht off
0 - 0.8
V
PWM Control Level
PWM
High
Level
2.0
3.3
5.0
V
PWM
Low
Level
0 - 0.15
V
PWM Control Duty Ratio
1 -
100 % @200Hz
PWM Control Frequency
fPWM
190
200
20K
Hz
LED Life Time
L
L
50,00
0
- - Hrs
(2)
Note (1) LED current is measured by utilizing a high frequency current meter as shown below:
Note (2) The lifetime of LED is defined as the time when it continues to operate under the conditions at
Ta = 25 ±2 and ILED = 55mADC (LED forward current) until the brightness becomes 50% of its
original value. Operating LED under high temperature environment will reduce life time and lead to color shift.
DK1211C User Guide
15
2.3 The Input Data Format
DK1211C User Guide
16
2.4 Optical Characteristics
Item
Symbol
Conditions
Min.
Typ.
Max.
Unit
Note
Color Chromaticity
Red
Rx
θx=0°, θy =0°
CS-2000
Typ -
0.05
0.600
Typ +
0.05
-
(1)(5)
Ry
0.353
Green
Gx
0.348
Gy
0.568
Blue
Bx
0.150
By
0.097
White
Wx
0.313
Wy
0.329
Center Luminance of White
Lc
400
450 - cd/m2
(4)(5)
Contrast Ratio
CR
1200
1500 - -
(2)(5)
Response Time
T
R
θx=0°, θy =0°
-
13
18
ms
(3)
TF -
12
17
White Variation
δW
θx=0°, θy =0°
-
1.25
1.4
-
(5)(6)
Viewing Angle
Horizontal
θx+
CR10
80
89
-
Deg.
(1)(5)
θx-
80
89
-
Vertical
θy+
80
89
-
θy-
80
89
-
DK1211C User Guide
17
Note (1) Definition of viewing angle:
Note (2) Definition of Contrast Ratio, CR:
The following expression can calculate the contrast ratio. Contrast Ratio, CR = L63 (255) / L0 L63: Luminance of gray level 63 (255) L 0: Luminance of gray level 0 CR = CR (5) CR (X) is corresponding to the Contrast Ratio of the point X at Figure in Note (6).
Note (3) Definition of Response Time (TR, TF) and measurement method:
DK1211C User Guide
18
Note (4) Definition of Luminance of White, LC:
Measure the luminance of gray level 63 (255) at center point LC = L (5) L (x) is corresponding to the luminance of the point X at Figure in Note (6).
Note (5) Measurement Setup:
The LCD module should be stabilized at given temperature for 20 minutes to avoid abrupt temperature change during measuring. To stabilize the luminance, the measurement should be executed after lighting Backlight for 20 minutes in a windless room.
Note (6) Definition of White Variation (δW):
DK1211C User Guide
19
2.5 Interface Timing
Item
Signal
Symbol
Min.
Typ.
Max.
Unit
Note
Total
Vertical Active Display Term
Tv
610
628
800
Th
Tv=Tvd+Tvb
Display
Tvd
-
600 -
Blank
Tvb
Tv-Tvd
28
Tv-Tvd
Total
Horizontal Active Display Term
Th
960
1056
1150
Tc
Th=Thd+Th
b
Display
Thd
-
800 -
Blank
Thb
Th-Thd
256
Th-Thd
Frequency
DCLK
Fc
34
40
48.3
MHz
Note (1): Because this module is operated by DE only mode, Hsync and Vsync input signals should be set to low logic level or ground. Otherwise, this module would operate abnormally.
Note (2): Frame rate is 60Hz
DK1211C User Guide
20
2.6 Power On/Off Sequence
To prevent a latch-up or DC operation of LCD module, the power on/off sequence should follow the conditions shown in the following diagram.
Note (1) Please avoid floating state of interface signal at invalid period. Note (2) When the interface signal is invalid, be sure to pull down the power supply of LCD
VCC to 0 V.
Note (3) The Backlight converter power must be turned on after the power supply for the
logic and the interface signal is valid. The Backlight converter power must be turned off before the power supply for the logic and the interface signal is invalid.
Parameter
Value
Unit
Min.
Typ.
Max.
T1
0.5 - 10
[ms]
T2
0 - 50
[ms]
T3
0 - 50
[ms]
T4
500 - -
[ms]
T5
200 - -
[ms]
T6
200 - -
[ms]
T7
5 - 300
[ms]
T8
10 - -
[ms]
T9
10 - -
[ms]
DK1211C User Guide
21
Chapter 3
Input Terminal Pin
Assignments
3.1 TFT LCD Module Interface
Pin #
Symbol
Description
Remark
1
RX3+
Differential Data Input, CH3 (Positive)
2 RX3-
Differential Data Input, CH3 (Negative )
3 GND
GND
4
SEL68
LVDS 6/8 bit select function control, Low or NC -> 6 bit Input Mode High -> 8bit Input Mode
Note ( 3 )
5
GND
GND
6
RXC+
Differential Clock Input ( Positive )
LVDS Level Clock
7
RXC-
Differential Clock Input ( Negative )
8
GND
GND 9
RX2+
Differential Data Input , CH2 ( Positive )
10
RX2-
Differential Data Input , CH2 ( Negative )
11
GND
GND 12
RX1+
Differential Data Input , CH1 ( Positive )
13
RX1-
Differential Data Input, CH1 ( Negative )
14
GND
GND 15
RX0+
Differential Data Input, CH0 ( Positive )
16
RX0-
Differential Data Input, CH0 (Negative )
17
reLR
Horizontal Reverse Scan Control, Low or NC -> Normal Mode. High -> Horizontal Reverse Scan
Note ( 3 )
18
reUD
Vertical Reverse Scan Control, Low or NC -> Normal Mode, High -> Vertical Reverse Scan
Note ( 3 )
19
VCC
Power supply
20
VCC
Power supply
DK1211C User Guide
22
Note (1) Connector Part No.: FI-SEB20P-HFE(JAE) or 076B20-0048RA-G4(STARCONN) or equivalent.
Note (2) User’s connector Part No.: FI-SE20ME(JAE) or equivalent
Note (3) “Low” stands for 0V. “High” stands for 3.3V. “NC” stands for “No Connected”.
DK1211C User Guide
23
3.2 Backlight Unit
Pin #
Symbol
Description
Remark
1
V
i
Converter input voltage
12V
2
V
i
Converter input voltage
12V
3
V
i
Converter input voltage
12V 4 V
i
Converter input voltage
12V
5
VGND
Converter ground
Ground
6
VGND
Converter ground
Ground
7
VGND
Converter ground
Ground
8
VGND
Converter ground
Ground
9
EN
Enable pin
3.3V
10
ADJ
Backlight Adjust
PWM Dimming
(190-210KHz, Hi: 3.3VDC,
Lo: 0VDC)
Note (1) Connector Part No.: 91208-01001-H01(ACES) or equivalent
Note (2) User’s connector Part No.: 91209-01011(ACES) or equivalent
DK1211C User Guide
24
This page is intentionally left blank
DK1211C User Guide
25
Chapter 4
Touch Screen
4.1 Touch Characteristics
4.1.1 General Specifications
Item
Specifications
Unit
Touch Technology
Projected capacitive touch
-
Touch Panel Size
12.1
inch
Touch Tail Design
FPC
-
View Area
247.00(W) x 185.50(H)
mm
Total Thickness
1.59±0.30
mm
Outline Dimension
290.00(W) x 220.50(H) x 1.59(D)
mm
Transparency
85%
-
Surface Hardness
7H
-
4.2 Absolute Maximum Ratings
4.2.1 Absolute Ratings of Environment
Item
Value
Unit
Note
Min.
Max.
Operating Ambient Temperature
-30
+70
°C
20%~90% RH at
max 50
Storage Temperature
-40
+80
°C
20%~90% RH at
max 50
DK1211C User Guide
26
4.3 Electrical Characteristics
(Ta=25±2°C)
Item
Symbol
Value
Unit
Note
Min.
Typ.
Max.
Power Supply Voltage
VDD
3.5
5.0
5.5 V
Response time
- - -
25
ms
Power Consumption
PL
- - 100
mA
@5.0V
Report Rate
RR
100 - -
Hz
DK1211C User Guide
27
4.4 Touch Pin Assignment
Pin No.
Symbol
1
GND_EARTH
2
VDD
3
GND
4
D+ 5 D-
Front View
DK1211C User Guide
28
This page is intentionally left blank
DK1211C User Guide
29
Appendix A
Handling Precautions
A1 Handling Precautions
(1) Do not apply rough force such as bending or twisting to the module during assembly.
(2) To assemble or install module into user’s system can be only in clean working areas. The
dust and oil may cause electrical short or worsen the polarizer.
(3) It’s not permitted to have pressure or impulse on the module because the LCD panel and Backlight will be damaged.
(4) Always follow the correct power sequence when LCD module is connecting and operating. This can prevent damage to the CMOS LSI chips during latch-up.
(5) Do not pull the I/F connector in or out while the module is operating.
(6) Do not disassemble the module.
(7) Use a soft dry cloth without chemicals for cleaning, because the surface of polarizer is very soft and easily scratched.
(8) It is dangerous that moisture come into or contacted the LCD module, because moisture may damage LCD module when it is operating.
(9) High temperature or humidity may reduce the performance of module. Please store LCD module within the specified storage conditions.
(10) When ambient temperature is lower than 10ºC may reduce the display quality, the response time will become slowly.
(11) Do not keep same pattern in a long period of time. It may cause image sticking on LCD.
(12) Do not disassemble the module or insert anything into the Backlight unit.
(13) If the liquid crystal material leaks from the panel, it should be kept away from the eyes or mouth. In case of contact with hands, skin, or clothes, it must be washed away thoroughly with soap.
(14) After the module’s end of life, it is not harmful in case of normal operation and storage.
DK1211C User Guide
30
This page is intentionally left blank
Loading...