Axiom 0511AXM0361 Users Manual
DOC-0361-010 Rev A. 11/28/05
MC13192U
Application Module for the Freescale MC13192
2.4GHz RF Transceiver
Hardware User Guide
Table of Contents
Cautionary Notes: ...........................................................................................................2
Terminology ....................................................................................................................2
Module Features .............................................................................................................3
Module Option Jumpers..................................................................................................4
JP1 - Select Signal Option...........................................................................................4
JP2 – Clock-Out Enable Option...................................................................................4
J1 Connector – Default Host I/O Connection ..................................................................4
J2 Connector...................................................................................................................5
J104 – SMA Test Connector...........................................................................................5
Installation.......................................................................................................................5
MCU Project Board - Module Installation.....................................................................6
CSM, DEMO or Host MCU Board - Module Installation on Socket Header.................6
CSM, DEMO or Host MCU Board - Module Installation on Ribbon Cable...................7
Supporting Platforms and Signal Charts .........................................................................7
CSM-12C32 Module Platform:.....................................................................................8
DEMO9S08RG60 Module Platform:............................................................................8
Axiom Manufacturing • 2813 Industrial Lane • Garland, TX 75041
!
Email: Sales@axman.com Web: http://www.axman.com
!
MC13192U Transceiver Module
User Guide
Cautionary Notes:
1) Electrostatic Discharge (ESD) prevention measures should be applied whenever
handling this product. ESD damage is not a warranty repair item.
2) Axiom Manufacturing reserves the right to make changes without further notice to
any products to improve reliability, function or design. Axiom Manufacturing does
not assume any liability arising out of the application or use of any product or circuit
described herein; neither does it convey any license under patent rights or the rights
of others.
3) EMC Information on the MC13192U Module:
a) This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1) This device may not cause harmful interference, and
2) This device must accept any interference received, including interference that
may cause undesired operation.
TX FCC ID# TFY1105AXM0361
b) Changes or modifications to this unit not expressly approved by Axiom
Manufacturing, could void the user’s authority to operate this equipment under
FCC or other regulatory agency rules.
c) This product is designed and intended for use as an application platform for
software development in an educational / professional laboratory. Use as a
communication device in end user equipment must follow the recommended
application in this manual.
d) In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate prevention measures.
e) RF Exposure – This device exceeds the FCC requirements for RF exposure when
the antenna used for this transmitter has a separation distance of at least 20cm
from all persons and must not be co-located or operating in conjunction with any
other antenna or transmitter.
Terminology
This module applies option selection jumpers. Terminology for application of the option
jumpers is as follows:
Jumper on, in, or installed = jumper is a plastic shunt that fits across 2 pins and
the shunt is installed so that the 2 pins are connected with the shunt.
2
MC13192U Transceiver Module
User Guide
Jumper off, out, or idle = jumper or shunt is installed so that only 1 pin holds the
shunt, no 2 pins are connected, or jumper is removed. It is recommended that
the jumpers be placed idle by installing on 1 pin so they will not be lost.
Signal names in this document that are followed by an asterisk (*) denote an active-low
signal.
Module Features
The MC13192U Transceiver module is a low cost demonstration or application module
for the Freescale MC13192 Zigbee™ capable transceiver device. Module operation is
controlled by any host microcontroller with a Serial Peripheral Interface (SPI) port.
Interface connections are compatible with several Freescale microcontroller DEMO and
EVB development boards. Development of applications for several microcontrollers is
quick and easy with the included demonstration example software.
♦ MC13192 Transceiver
* SPI interface
* 2.4GHz RF operation
* Optional clock output 32KHz to 8MHz (JP2)
♦ 16Mhz reference Crystal
♦ On Board “F” antenna with TX/RX switch
♦ SMA test jack connection
♦ Regulated +3.0V power supply
♦ SPI Slave operation, 2 optional chip selects (JP1).
♦ J1 I/O connector standard, 2x12 R/A pins
MCU DEMO module or SLK series compatible
♦ J2_GP PORT connector optional, 2x 15 R/A pins
M68EVB9S08GB60 board compatible
♦ Power ON Indicator
♦ Size: 2 x 2.1 inches with 2 x 4-40 size mounting holes
♦ +3.3V to +5.5V input supply on I/O connector
♦ I/O Level translation for 3.3 to 5V systems
♦ 60ma maximum with TX on.
♦ FCC registered when applied with provided software examples.
♦ Supplied in Module pairs with Documentation (CD),
User Manual, and SMAC example software
MC13192U
The MC13192U provides a low cost method to apply RF communication to any system.
Supporting application software examples are available for Freescale Coldfire™,
HC(S)12, and HCS08 targets. Modules are provided in pairs in the standard kit and are
certified with the FCC for application in other systems.
Standard installation places module at 90 degrees vertical to controller or host platform.
Versatile connection to host controller boards will allow stacking in different
configurations or connection by ribbon cable, contact Axiom with special requirements.
Module applies an embedded antenna and derives the 3.3V to 5.5V DC input power
from the supporting host platform so no other accessories are required. Mounting holes
are provided opposite from the connector to secure the module if required, 4-40 size
nylon hardware should be applied for this purpose.
3
Loading...