axing HKI 41-34, HKI 41-35, HKI 81-34 Operation Instructions Manual

HKI 41-34 | HKI 41-35
HKI 81-34 | HKI 81-35

IPTV Encoders

Operation instructions

Operation instructions | HKI 41-34 | HKI 41-35 | HKI 81-34 | HKI 81-35

2 2017-07-25 | Technical changes, design modifications, errors and misprints are subject to change without prior notice.

Table of contents

1. Product description ........................................................................................................................................ 4

1.1. General.................................................................................................................................................. 4

1.2. Scope of delivery ................................................................................................................................... 4

1.3. Connectors on the rear side .................................................................................................................. 4

1.4. Typical Application................................................................................................................................. 5

2. Mounting and Installation ............................................................................................................................. 6

3. IP integration ................................................................................................................................................. 7

3.1. Default IP addresses and logins:............................................................................................................ 7

3.2. Change the IP addresses into the required IP address space ................................................................. 7

4. Configuration............................................................................................................................................... 10

4.1. Maintenance ....................................................................................................................................... 10

4.1.1. Network ...................................................................................................................................... 10

4.1.2. Change password ....................................................................................................................... 10

4.1.3. Upgrade ...................................................................................................................................... 11

4.1.4. Reset ........................................................................................................................................... 11

4.2. Status of the Encoders ......................................................................................................................... 11

4.2.1. Stream URL of the encoders ........................................................................................................ 12

4.2.2. Substream URLs of the encoders ................................................................................................. 12

4.3. Encoder Se ttings.................................................................................................................................. 13

4.3.1. Main stream ................................................................................................................................ 13

4.3.2. Substream1…3 ........................................................................................................................... 14

4.3.3. Audio settings ............................................................................................................................. 14

4.3.4. Advanced .................................................................................................................................... 15

4.4. OSD Setting ......................................................................................................................................... 15

4.4.1. Streaming OSD Setting ................................................................................................................ 15

4.4.2. Substream1…3 ........................................................................................................................... 16

4.4.3. LOGO uploading ......................................................................................................................... 16

5. Application examples .................................................................................................................................. 17

5.1. Preview with the stream with Windows Media Player ........................................................................ 17

5.2. Multi Local User Application Multicast Way ........................................................................................ 18

5.3. Local Surveillance System Application NVR Connection ...................................................................... 19

5.4. Remote Multi User Application RTMP Connection............................................................................... 20

6. Technical spe cifications ............................................................................................................................... 22

2017-07-25 | Technical changes, design modifications, errors and misprints are subject to change without prior notice. 3

Safety instructions:

∂ The installation of the device and repair work on the device must be carried out only by a professional

in accordance with the applicable VDE directives. In case of incorrect installation, no liability is
assumed.

∂ Never open the device. There are no parts to be maintained by the user inside the device, however,

lethal voltages are present. This also applies to cleaning the device or working on the connections.

∂ Use only the mains cable connected to the device or the enclosed power supply unit. Never replace any

parts or make any modifications to the mains cable and the power supply unit. Otherwise, there is a
risk of death.

∂ If a replaceable fuse is available, pull out the mains plug before replacing the fuse. Replace defective

fuses only by standardized fuses with the same nominal value.

∂ If you intend not to use the device for a longer period of time, we recommend you to completely

disconnect the device from the mains for safety reasons and for saving energy by pulling out the mains
plug.

∂ Let the device adjust to the room temperature before commissioning, in particular if condensation is

present on the device, or if it was exposed to large temperature fluctuations.

∂ The device must be operated only in moderate climate.
∂ The device must be operated only in dry rooms. In damp rooms or outdoors, there is a risk of short-

circuits (attention: risk of fire) or electrical shocks (attention: risk of death).

∂ Plan the mounting or installation location such that you can easily reach the mains plug and interrupt

the electric circuit in dangerous situations. Select the mounting or installation location such that
children cannot play near the device and its connections without supervision. The mounting or
installation location must allow a safe installation of all connected cables. Power supply cables and
supply cables must not be damaged or squeezed by any objects.

∂ Select a mounting or installation location which meets the requirements of the IP 54 protection class.

Operate the device only on a flat, firm surface and protect it against unintentional movements.

∂ Never expose the device to direct solar irradiation and avoid direct vicinity of heat sources (e.g.

heaters, other electrical appliances, fireplace, etc.). It must be always ensured that devices with cooling
elements or ventilation slots are not covered or obstructed. In addition, ensure generous air circulation
around the device. This will prevent possible damage to device and risk of fire due to overheating. It
must be always ensured that cables are not located near heat sources (e.g. heaters, other electrical
appliances, fireplace, etc.).

∂ The device is intended for transmission of audio and video signals via LAN cable. Misuse of the device

is expressly prohibited.

∂ In particular, the warranty and liability shall be excluded for the consequences of incorrect use, in case

of incorrect modifications or repair work carried out by the customer. Use the device only as described
in the operating instructions and in particular according to the state-of-the-art.

∂ The antenna system must be installed and grounded according to the current DIN EN 60728-11

standard.

∂ The product complies with the directives and standards for CE labeling.

Operation instructions | HKI 41-34 | HKI 41-35 | HKI 81-34 | HKI 81-35

4 2017-07-25 | Technical changes, design modifications, errors and misprints are subject to change without prior notice.

1. Product description

1.1. General

HKI 41-34 IPTV Encoder with H.264 coding

4 × HDMI

HKI 41-35 IPTV Encoder with H.265 (HEVC) coding

4 × HDMI

HKI 81-34 IPTV Encoder with H.264 coding

8 × HDMI

HKI 81-35 IPTV Encoder with H.265 (HEVC) coding

8 × HDMI

Common Features:

∂ Web-based configuration | Remote maintenance
∂ Two redundant power supplies (hot pluggable)

1.2. Field of application:

The devices are only suitable for in-house distribution of HDMI signals over IPTV. If a device is used for other
purposes, no warranty is given!

1.3. Scope of delivery

1 × IPTV Encoder

2 × AC connection cable, power cord

1 × Quick start guide

1.4. Connectors on the rear side

1. AC connectors of the power supplies

2. RJ-45 Ethernet port of the controler

3. RJ-45 Ethernet ports of Encoder 1…4

4. RJ-45 Ethernet ports of Encoder 5…8 (HKI 81-xx)

5. HDMI inputs 1…4

6. HDMI inputs 5…8 (HKI 81-xx)

2017-07-25 | Technical changes, design modifications, errors and misprints are subject to change without prior notice. 5

1.5. Typical Application

Operation instructions | HKI 41-34 | HKI 41-35 | HKI 81-34 | HKI 81-35

6 2017-07-25 | Technical changes, design modifications, errors and misprints are subject to change without prior notice.

2. Mounting and Installation

Installation may be performed by authorized and skilled electricians only.

Mounting and installation in a 19“rack

The IPTV encoders are mounted in a 19" rack
Mount the unit with four fitting screws (1).

Equipotential bonding

The HKI must be connected to the equipotential bonding according to EN 60728-11.

Power supply

The HKI have two built-in power supply.
Connect both power supplies to an electrical outlet (100 ... 240 VAC / 50 ... 60 Hz).

2017-07-25 | Technical changes, design modifications, errors and misprints are subject to change without prior notice. 7

3. IP integration

The HKI 41-3x includes 1 controler and 4 encoders

The HKI 81-3x includes 1 controler and 8 encoders

All this sub devices have to be in the same IP adress space, to communicate with each other.

3.1. Default IP addresses and logins:

The device is configured via the graphical user interface. To access the user interface, you need a standard
PC/laptop with a network interface, a commercially available network cable and the actual version of the
installed web browser.

IP adress User/password

Control port interface 192.168.0.157 admin/Ramsen8262

Encoder 1 192.168.0.161 admin/admin

Encoder 2 192.168.0.162 admin/admin

Encoder 3 192.168.0.163 admin/admin

Encoder 4 192.168.0.164 admin/admin

Encoder 5 192.168.0.165 admin/admin

Encoder 6 192.168.0.166 admin/admin

Encoder 7 192.168.0.167 admin/admin

Encoder 8 192.168.0.168 admin/admin

3.2. Change the IP addresses into the required IP address space

If the address space of your network does not match that of the HKI (192.168.0.xyz), change the encoder IP
addresses step by step into the required IP address space.

1st Step – change encoders IP addresses in required IP address space.

Configure your computer in to the same IP address space as the default IP addresses of the encoders.

For example: 192.168.0.50

Enter via browser the encoder web interfaces one by one and configure them in to the required address

space.

…

For example:

Encoder 1: 192.168.178.110

Encoder 3: 192.168.178.112

Encoder 5: 192.168.178.114

Encoder 7: 192.168.178.116

Encoder 2: 192.168.178.111

Encoder 4: 192.168.178.113

Encoder 6: 192.168.178.115

Encoder 8: 192.168.178.117

Operation instructions | HKI 41-34 | HKI 41-35 | HKI 81-34 | HKI 81-35

8 2017-07-25 | Technical changes, design modifications, errors and misprints are subject to change without prior notice.

2nd Step – change the control port IP address in the required IP address space.

Enter via browser the control port web interface (192.168.0.157) and configure it also in to required address

space.

For example: 192.168.178.100 it must be in the same IP-adress space.

Note: After this the connection to the controller is interrupted.

3rd Step – assign the encoder IP addresses in the control port web interface

Configure your computer to the same IP address space as the encoders and the controller.

For example: 192.168.178.50

Enter via browser the web interface of the controller (192.168.178.100).
Choose MAINTENANCE>Network>Encoder IP addresses
Type in the changed encoder IP addresses.

For example:
– Encoder 1: 192.168.178.110

– Encoder 2: 192.168.178.111
– Encoder 3: 192.168.178.112
– Encoder 4: 192.168.178.113
– Encoder 5: 192.168.178.114
– Encoder 6: 192.168.178.115
– Encoder 7: 192.168.178.116
– Encoder 8: 192.168.178.117

Click Apply.