AXICOM P1 Service Manual

P1 Relay

The Best Relaytion

ISO
9001

108-98009

Rev. C

EC-JM00-0009-03

ECOC: JM10

1. Aug. 04

1 pole telecom and signal relay, polarized,
Through Hole Type (THT) or
Surface Mount Technology (SMT),

Relay types: non-latching with 1 coil
latching with 2 coils
latching with 1 coil

Features

– Directly triggerable with TTL standard modules such
as ALS, HCT and ACT

– Slim line 13.5 x 7.85 mm, 0.531 x 0.309 inch

– Switching current 1 A

– 1 changeover contact (1 form C / SPDT)

– Bifurcated contacts

– Immersion cleanable

– High sensitivity results in low nominal power consumption
65 to 130 mW for non-latching
30 to 150 mW for latching

– Surge voltage resistance between contact and coil:

- 2.5 kV (2 / 10 µsec) meets the Bellcore Requirement GR-1089

- 1.5 kV (10 / 160 µsec) meets FCC Part 68

Typical applications

– Automotive equipment
CAN bus, imobilizer

– Office equipment

– Measurement and control equipment

– Medical equipment

– Safety equipment

Options

– FCC version on request. Testing of open contacts with surge
voltage in accordance with FCC 68.302 (1.5 kV, 10/160 µsec)

P1 Relay V23026

Basic insulation coil/contacts according to IEC/EN 60950
Clearance > 0.75 mm
Creepage distance > 0.75 mm

UL File No. E 111441

Page 2 (10) 108-98009 Rev. C

European Directive conformance:

P1 relay product conformance according to:

- Directive 2000/53/EC: ELV (End of Life of Vehicles)

- Directive 2002/95/EC: ROHS (Restrictions of the
use of certain hazardous substances in electrical and
electronic equipment)

Compliance is evidenced by written declaration from all raw
material suppliers.
Tyco Electronics AXICOM only has responsibility for the proper
processing of these materials.
Confirmation is valid for date codes ≥ 0429

Dimensions

V23026-x1xxx-B201
THT SMT
mm inch mm inch

L 13.0 ± 0.1 0.512 ± 0.004 13.4 ± 0.1 0.528 ± 0.004
W 7.6 ± 0.1 0.299 ± 0.004 7.75 ± 0.1 0.305 ± 0.004
H 6.9 - 0.2 0.272 - 0.008 8.0 - 0.2 0.315 - 0.008
T 3.5 - 0.2 0.138 -0.008 N/A N/A
T1 N/A N/A 10.9 - 0.5 0.429 - 0.020
T2 5.08 ± 0.15 0.200 ± 0.006 5.08 ± 0.15 0.200 ± 0.006
S 0.3 ± 0.1 0.012 ±0.004 N/A N/A
S1 N/A N/A 0.85 ± 0.1 0.033 ±0.004
S2 N/A N/A 0.2 - 0.15 0.008 ±0.006

P1 Relay V23026

Terminal assignment

Relay - top view

Mounting hole layout

View onto the component side of the PCB

Solder pad layout

View onto the component side of the PCB

Contact release or reset condition, coil polarity to set the relay

THT Version

SMT Version

Latching type, 2 coils
reset condition

Non-latching type,
not energized condition

Latching type, 1 coil
reset condition

Page 3 (10) 108-98009 Rev. C

Contacts are shown in reset
condition. Both coils can be
used either as set or reset coil.