Axial Racing AX90026 User Manual
4
4
4
2
4
4
4
3
Removing the Body
1.
Put the battery in the car.
Do not use a Nickel Cadmium or Nickel Metal Hydride battery charger to
charge LiPo batteries. Damage to the batteries and charger will likely
occur resulting in a fire.
Verwenden Sie keine Nickel-Cadmium-oder Nickel-Metall-Hydrid-Akku
Ladegerät LiPo-Akkus aufladen. Schäden an den Batterien und
Ladegerät wird wahrscheinlich auftreten, was zu einem Brand.
Ne pas utiliser un chargeur de batterie au nickel-cadmium ou
nickel-métal-hydrure pour recharger les batteries LiPo. Les dommages
aux batteries et le chargeur se produira probablement de provoquer un
incendie.
Install the battery
2.
Put back the Body.
3.
Turn on the transmitter.
Turn on the electronic speed controller.
4.
4
Top View Parts
Front Shock
Absorber
Steering Rack
Spur/Pinion/Slipper
(Under Cover)
Brushless Motor
Transmission
Front Bumper
Front Control Arm
Front Body Mount
Steering Servo
Electronic Speed
Control (ESC)
Battery Tray
Adjustable Battery
Clamp
Rear Shock
Absorber
Battery Door
Realistic Fuel Cell
Rear Swing Arm
Rear Axle
5
Getting-Started Checklist
The following checklist is a guide for getting you vehicle running for the first time.
Read ‘Cautions’ in Manual. (Page 2)
Charge battery pack. (Page 4)
Familiarize yourself with vehicle and
its components.
Install 4X AA batteries into Transmitter.
(Page 7)
Even though the vehicle is new check
driveshaft setscrews and other screws to
make sure they are tight from the factory.
Install battery pack in vehicle. (Page 4)
Turn on transmitter FIRST then ESC.
(Page 4)
Drive vehicle, challenge yourself and
have fun!
Check to make sure steering and throttle
operation work correctly. (Page 7)
Maintain vehicle. (Next Page)
6
Range check radio system. (Next Page)
Range-Checking Your Radio System
The radio system should be checked before operating the vehicle to ensure it’s operating properly and has adequate range.
1. Turn on the transmitter first and then the vehicle.
2. Have a friend hold the vehicle while keeping hands and loose clothing away from moving parts.
3. Walk away until you are at the farthest distance you plan to operate the vehicle.
4. Steer the vehicle back and forth and throttle both forward and reverse making sure there is no erratic behavior.
5. If any erratic behavior is exhibited do not operate the vehicle, call customer service for further assistance.
RANGE-CHECKING FOR DISTANCE
Maintaining Your Vehicle
Just like a full size car or truck your RC vehicle must undergo periodic maintenance in order to ensure peak running performance. Preventative
maintenance will also help avoid needless breakages which could result in costly repairs. Below are some suggestions to properly maintain
your vehicle.
REPLACE ANY NOTICEABLE
BENT OR BROKEN PARTS
CHECK FOR WEAR ON
THE BALL JOINTS IN THE
STEERING AND SUSPENSION
(REPLACE IF NECESSARY)
LINKS
CHECK DRIVESHAFT SET
SCREWS AND RE-THREAD
LOCK IF NECESSARY
INSPECT SHOCK
ABSORBERS FOR SMOOTH
DAMPENED OPERATION
CHECK FOR ANY LOOSE
CONNECTIONS OR FRAYED
WIRING
CHECK WHEEL NUTS MAKING
SURE THEY’RE SNUG
CHECK SLIPPER CLUTCH IF
APPLICABLE, FOR PROPER
OPERATION
CHECK TIRES MAKING SURE
THE BEADS ARE STILL FIRMLY
BONDED TO THE ENTIRE
CIRCUMFERENCE OF THE RIM
CHECK RECEIVER ANTENNA
TO CONFIRM IT’S NOT
DAMAGED
KEEP CHASSIS FREE OF DIRT
OR DEBRIS
CHECK STEERING
OPERATION FOR ANY BINDS
7
CHECK FOR LOOSE SCREWS
ON CHASSIS ESPECIALLY
THE KNUCKLE, C-HUB AND
AXLE LOCKOUT SCREWS
INSPECT THE SPUR AND
PINION GEARS FOR DAMAGE
CHECK DRIVELINE FOR
SMOOTH BIND-FREE
OPERATION
REPLACE TRANSMITTER
AA’S IF THE GREEN LIGHT IS
BLINKING
Recommended motor: AX31047
Battery Tray Access and Setup
1.Remove clip to open battery access door
2.Slide battery in to check height
3.Remove X4 M3x8mm AXA114 Screw
4.Drop battery clamp down to required battery height.
Snug fit required
5.Reinstall X4 M3x8mm AXA114 Screws
2
AXA114
AXA114
AXA114
AXA114
1
3
AXA114
AXA114
AXA114
AXA114
8
See instructions
below
BIND
ST-TRIM TH-TRIM ST-D/R
9
Loading...