Axial AX90028-I001 Instruction Manual
2
3
Removing the Body
1.
Put the battery in the car.
3.
Turn on the transmitter.
Install the battery
2.
Put back the Body.
Turn on the electronic speed controller.
4.
4
Getting-Started Checklist
The following checklist is a guide for getting you vehicle running for the first time.
Read ‘Cautions’ in Manual. (Page 2)
Familiarize yourself with vehicle and its components.
Even though the vehicle is new check driveshaft setscrews and other screws to make sure they are tight from the factory.
Charge battery pack. (Page 4)
Install 4X AA batteries into Transmitter. (Page 7)
If you are using NiMH or NiCd batteries turn OFF Lipo cut-off on the ESC. (Page 6 'Notes')
Install battery pack in vehicle. (Page 4)
Turn on transmitter FIRST then ESC. (Page 4)
Check to make sure steering and throttle operation work correctly. (Page 7)
Range check radio system. (Below)
Drive vehicle, challenge yourself and have fun!
Maintain vehicle. (Below)
Range-Checking Your Radio System
The radio system should be checked before operating the vehicle to ensure it’s operating properly and has adequate range.
1. Turn on the transmitter first and then the vehicle.
2. Have a friend hold the vehicle while keeping hands and loose clothing away from moving parts.
3. Walk away until you are at the farthest distance you plan to operate the vehicle.
4. Steer the vehicle back and forth and throttle both forward and reverse making sure there is no erratic behavior.
5. If any erratic behavior is exhibited do not operate the vehicle, call customer service for further assistance.
Maintaining Your Vehicle
Just like a full size car or truck your RC vehicle must undergo periodic maintenance in order to ensure peak running performance. Preventative
maintenance will also help avoid needless breakages which could result in costly repairs. Below are some suggestions to properly maintain
your vehicle.
• Replace any noticeable bent or broken parts.
• Keep the chassis free of dirt and debris.
• Check for loose screws on chassis especially the knuckle, c-hub, and axle lockout screws.
• Check for wear on the ball joints in the steering and suspension links, replace if necessary.
• Check driveshaft set screws and re-thread lock if necessary.
• Check wheel nuts making sure they’re snug.
• Check tires making sure the beads are still firmly bonded to the entire circumference of the rim.
• Replace transmitter AA’s if the green light is blinking.
• Inspect the spur and pinion gears for damage.
• Check slipper clutch, if applicable, for proper operation. (See page 25 Step 23 for Setup Instruction)
• Check driveline for smooth bind-free operation.
• Check for any loose connections or frayed wiring.
• Check steering operation for any binds.
• Inspect shock absorbers for smooth dampened operation.
• Check receiver antenna to confirm it’s not damaged.
5
AXIAL LIMITED WARRANTY
Your Axial product is warranted to be free of defects in materials and workmanship when new in the factory sealed box. This warranty does not cover
damages due to normal wear and tear, users' failure to perform routine maintenance, error of assembly or installation, modifications or addition of
aftermarket parts or option parts. This warranty lasts as long as the original purchaser owns the product and is not transferable (verified by dated
itemized sales receipt accompanied with product). In the event of a defect under this warranty, Axial will, at our discretion, repair or replace the
product, provided our inspection indicates that an original defect exists. Axial provides a 10-day warranty from the date of purchase on electronics
(i.e. servo, esc, radio). Axial reserves the right to replace any product which is no longer available with a product of comparable value and function. If
Axial determines the repair is not covered under warranty guidelines, there could be a charge applied for the repair and return shipping charges. Note:
Purchasing products from unauthorized distributors may void warranty and prevent support and service.
INTERNATIONAL CUSTOMER WARRANTY
Please return product to the dealer where the purchase was made. If your Axial product purchase was made through an on-line retailer, any
warranty issues must be taken care of by that retailer. Axial assumes no responsibility for Axial products sold internationally by on-line retailers.
REPAIR
For warranty repair, please contact Axial Customer Service at (877) 64-AXIAL (877-642-9425).
HOURS AVAILABLE:
8:00 am - 5:00 pm Monday through Friday, Central Time.
If you're using NiMH or NiCd batteries turn " OFF " LiPo Cut- Off by visiting the following link for Manually Programming the AE- 2 ESC :
http: //www. axialracing. com/instructions .
You can also use the Castle Link to access LiPo Cut- Off and other advanced settings in the ESC .
6
BIND
ST-TRIM TH-TRIM ST-D/R
7
8
AX30146
Shock Shaft 3x50mm
AX30162
Pin 1.5x8mm
AX30166
Pin 1.5x11mm
AX30163
Pin 2x10mm
x4
x2
x4
x6
AX30435
Outdrive Shaft
x1
AX30408
Input Shaft 5x29mm
x2
AX30435
Outdrive Shaft
x1
AX30200
Spring 12.5x20mm
AX30784
Drive shaft Coupler
AX30785
Drive shaft Output
x4
x4
x4
AX30207
Spring 12.5x40mm
AX30412
Slipper Pad 27x8x1mm
AX30385
Diff Gasket 16x25x0.5mm
AX30463
Universal joint Axle Pin holder
x4
x2
x4
x1
AX30410
Inner Slipper Plate
AX30413
Spring 8.5x12
x1
x1
AX30411
Outer Slipper Plate
AX30427
12mm Aluminum Hub
AX30420
Solid Axle Dogbone 6x74mm
x1
x4
x2
AX30393
13T Bevel Gear
x2
AX30491
AX10 Scorpion Motor Plate
x1
AX30392
38T Bevel Gear
x2
AX30421
Solid Axle Dogbone 6x104.5mm
AX30450
Flange Pipe 3x4.5x5.5
AX30499
5x6.9x4.8
x2
x4
x1
x2
AX30578
Pinion 48DP 20T
x1
AX30502
SCX10 Chassis Rail
x2
9
AXA013
M2x6mm
AXA015
M2x10mm
x7
x8
AXA1230
Bearing 10x15x4mm
x6
AXA434
M3x8mm Hex Socket Tapping Button Head
x2
AXA083
M3x6mm
AXA085
M3x10mm
AXA087
M3x16mm
AXA088
M3x20mm
AXA089
M3x25mm
AXA1040
M3 Thin Hex Nut
AX1045
M4 Nylon Lock Nut
AXA1053
M3 Nylon Locking Hex Nut
AXA1052
M3 Thin Nylon Locking Hex Nu
AXA1059
6mm Body Clip
AXA1179
O-Ring 2.5x1.5mm
AXA1070
Washer 3x6x0.5mm
AXA1071
Washer 4x8x0.5mm
AXA1091
Washer 5x10x0.5mm
AXA1163
O-Ring 7x1mm
AXA1218
Bearing 5x10x4mm
AXA1221
Bearing 5x11x4mm
x5
x4
x8
x1
x7
x4
x5
x10
x1
x10
x8
x6
x1
x1
x4
x4
x10
AXA1280
M3x10mm
AXA1290
M3x4x14mm Step Screw
AXA1358
Shock Damper 3x7x8
AXA1392
E2 e-clip
AXA1393
E2.5 e-clip
AXA176
M3x2.5x13mm Screw Shaft
AXA0175
Screw Shaft M3x2.5x11mm
AXA180
M3x3mm Set Screw
AXA113
M3x6mm Hex Socket Button Head
AXA117
M3x15mm Hex Socket Button Head
AXA119
M3x20mm Hex Socket Button Head
AXA121
M3x30mm Hex Socket Button Head
AXA144
M3x8mm Hex Socket Flat Head
AXA0422
M2.6x6mm Hex Socket Button Head
AXA0424
M2.6x10mm Hex Socket Tapping Button Head
x4
x2
x4
x8
x2
x8
x4
x5
x7
x1
x4
x1
x4
x7
x20
AXA435
M3x10mm Hex Socket Tapping Button Head
AXA436
M3x12mm Hex Socket Tapping Button Head
AXA0437
M3x15mm Hex Socket Tapping Button Head
AXA438
M3x18mm Hex Socket Tapping Button Head
AXA0439
M3x20mm Hex Socket Tapping Button Head
AXA440
M3x25mm Hex Socket Tapping Button Head
AXA0443
M3x40mm Hex Socket Tapping Button Head
AXA0414
M2.6x10mm Hex Socket Tapping Flat Head
AXA463
M3x6mm Hex Socket Tapping Flat Head
AXA464
M3x8mm Hex Socket Tapping Flat Head
AXA465
M3x10mm Hex Socket Tapping Flat Head
AXA466
M3x12mm Hex Socket Tapping Flat Head
x10
x1
x12
x4
x2
x2
x1
x3
x3
x14
x4
x6
AXA1225
Bearing 8x16x5mm
x2
AXA0425
M2.6x12mm Hex Socket Tapping Button Head
AXA433
M3x6mm Hex Socket Tapping Button Head
10
x2
x13
AX80010
Gear Set
x1
AX80003
AX80012
2 1
AX80003
Solid Axle Set
AX80004
1 1
AX80004
Hub Set
AX80012
C Hub Carrier
2 3
x1
1 2 3 4
5 6 7 8
AX80006
x2
AX80020
1
AX80006
Servo Set
AX80020
Straight Axle Adapter Parts Tree
AX80018
11
11
2
22
33
x1
AX80018
Hardware Parts Tree
x2
x1
AX80009
Transmission Set
x1
7
1
AX80009
6
x1
1
23
45
AX80017
1 1
2 3 2
AX80017
Steering Linkage Parts Tree
x1
AX80025
AX 80025
SCX10 Shock Hoops Parts Tree
1 1
AX80041
2
AX80041
1/10th Scale Rock Rails Set
x2
AX80078
33
12
Transmission Gear Cover
x1
x1
AX80002
Diff Case
x2
11
AX80043
Links Parts Tree
x2
2
5
3
6
1
5
1
AX8140
1.9 Wheel - 26mm wide (Shining Chrome/Black)
x5
12
2
5
4
2
4
3
1
AX80054
3
1
6
AX80054
SCX10 RTR Links Parts Tree (130mm)
X
1
8
7
AX80121
Poison Spyder Front Fenders and Mounts
X
1
5
AX80123
Jeep Wrangler Cage Top and Accessories
4
3
3
1
2
6
1
2
3
2
1
X
1
6
5
7
8
AX80122
3
4
AX80124
AX80121
3
4
AX80122
Poison Spyder Rear Fenders and Mounts
9
10
10
9
X
1
9
9
9
456
AX80084
UV Joint Driveshafts
1
AX80125
Poison Spyder Front Bumper
12
AX80084
X
1
AX80125
1
2 3
AX80124
Jeep Wrangler Cage Sides and Washers
2
3
3
2
X
1
9
4
X
1
5 5
2
3 3
1
4
AX80126
4 4
AX80126
Poison Spyder Rear Bumper and Spare Tire Carrier
6
7
8
X
1
13
AX30408
Input Shaft 5x28mm
AX30163
Pin 2x10mm
AXA1393
E2.5 e-clip
AX30393
13T Bevel Gear
x1
x1
x1
AXA1393
x1
AX30163
AX30393
AX30408
AX80002
AX30500
AX30500
Heavy Duty Lovker
AX30392
38T Bevel Gear
AXA1230
Bearing 10x15x4mm
AXA1221
Eearing 5x11x4mm
x1
AXA015
M2x10mm
x1
x2
x2
x4
AX30420
AXA1230
AXA1221
AX30385
AX30392
AXA015
AX30420
AX30420
Solid Axle Dogbone 6x74mm
AX30385
Diff Gasket 16x25x0.5mm
x1
x2
AX30464
AX10 Scorpion Universal Joint
AXA1230
AXA1221
14
AXA1221
Bearing 5x11x4mm
x2
AXA085
M3x10mm
AXA087
M3x16mm
x2
x2
AXA1040
M3 Thin Hex Nut
If Gear mesh is tight,
make sure input shaft
is seated correctly.
x2
AXA1221
AXA085
AX80003
AXA087
AXA1040
AXA1221
AX80003
AXA1040
AX80018
AX80003
15
3
AXA433
M3x6mm
x4
AXA433
AX80012
AXA433
AX30495
Aluminum C Hub Carrier
AXA433
Note Direction
Richtung beachten
AX80012
AXA433
AX30450
Flange Pipe 3x4.5x5.5
AXA435
M3x10mm
AXA1221
Bearing 5x11x4mm
AXA1230
Bearing 10x15x4mm
AX30366
Axle 5x35mm
x4
x2
x2
x2
x4
Note Direction
D0 not overtighten
AXA435
AXA435
AX30450
AXA1221
AX80004
AX30450
AX1230
AX30366
Note Direction
D0 not overtighten
AXA435
AX30496
Aluminum Knuckle
Note Direction
D0 not overtighten
16
Note Direction
Richtung beachten
AX30450
Note Direction
D0 not overtighten
AXA435
Loading...