Axess SPBP4401 User Manual

Download

TWIN BLUETOOTH CONE SPEAKERS

MODEL NO: SPBP4401

Safety information

Important - Please read these instructions fully before

installing or operating

General safety information

• Keep the product and all its parts out of reach of small children.

• This product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.

• Do not attempt to open the product. This product does not contain any user serviceable parts. Unauthorised handling of the device may damage it and will void your warranty.

• Do not use your Wireless Speakers near emergency/intensive care medical equipment; if you have a pacemaker fitted or during an electrical storm.

• To avoid possible hearing damage, do not listen to these Wireless Speakers at high volume levels for long periods of time. Always keep the volume within reasonable limits.

Power source

• Only use the USB charging cables that came with the product. Using unauthorised charging cables will invalidate your guarantee and may irrecoverably damage the product..

• Please charge the integral lithium battery in your Wireless Speakers at least once a month, to prevent damage to and prolong the life of the lithium battery.

Positioning the Wireless Speakers

It is important that you consider carefully in advance where your Wireless Speakers will be situated and make sure that they are:

• on a flat and stable surface.

• at least 1 metre away from other electrical appliances to avoid interference.

• where they will be in range of the connected or ‘paired’ bluetooth device (e.g. iPod/ iPhone/iPad/Android/other phone/computer, which is about 10 metres or less (33 feet or less) in line of sight.

Safety information

Important - Please read these instructions fully before

installing or operating

• Within 5 metres of each other, without obstructions between them.

• Never place your Wireless Speakers directly onto antique or polished surfaces.

Moisture and water

• Do not leave your Wireless Speakers in low temperatures as moisture can form inside

the product, which may damage the circuit board.

Ventilation

• Do not block or cover slots, holes or openings on the product by placing on soft

furnishings such as carpets, rugs or beds as these are provided for functionality and/or ventilation to ensure safe operation of the product.

eat sources and ﬂames

• Do not leave your Wireless Speakers in high temperatures as electronic devices and

plastic parts may warp in heat.

Getting to know your Wireless Speakers

You’ll be up and running in no time

Ready? Let’s begin...

Please read these instructions carefully. They contain important information which will help you get the best from your product and ensure safe and correct installation and operation.

Accessories

The following accessories are included with your Wireless Speakers:

2 x Micro USB Cables.

ig 1.

Getting to know your Wireless Speakers

You’ll be up and running in no time

Fig 2.

LED status indication

Microphone

3. Power On/Off/Answer/End Call/

Pairing/Play/Pause

4. Aux in socket

5. USB charging socket

Getting to know your Wireless Speakers

You’ll be up and running in no time

Power connection

1. Connect the micro USB end of the charging cables to the USB socket on each Wireless Speaker (Fig 3). Plug the standard end of each USB charging cable into a computer or other USB charging device.

2. The small LED status indicator on the front of each Wireless Speaker, behind the speaker mesh will light up. If the LED is red the Wireless speaker battery is charging, when the LED changes to blue the battery is fully charged.

Note: Charging the battery before first use, may take up to 3 hours per speaker.

3. When fully charged, unplug the micro USB charging cables.

Note: Your Wireless speakers have an approximate playtime of 8 hours, before they

need to be recharged. When the battery power is low, the LED indicator will flash quickly and you should plug in and recharge your Wireless Speakers straight away.

Fig 3.

Getting to know your Wireless Speakers

You’ll be up and running in no time

Initial set-up

1. Press and hold the Power On button on the top of each Wireless Speaker for about 5

seconds, until ‘Power on, pairing’ is announced, then release the power on buttons.

2. The Wireless Speakers will pair with each other. ‘Pairing successful’ will be announced,

followed by ‘ Left Channel’ and ‘Right channel’ by each speaker, as appropriate.

3. ‘Pairing’ will be announced again as your Wireless Speakers search for a Bluetooth

device to connect to.

Connecting or ‘Pairing’ with your Wireless Speakers

1. On the device that you would like to connect to your Wireless Speakers via Bluetooth

(e.g. iPhone/iPad/Android/other phone/Tablet/Computer), turn on Bluetooth connectivity and ensure that it is ‘discoverable’.

Note: If necessary, refer to the instructions for your device to add or set up Bluetooth.

2. Select to ‘Add new device’, if necessary.

Note: Some products will automatically search for a new device and so the ‘Add new

device’ option is not available.

When found, your Wireless Speakers will be displayed as ‘AAM

to begin pairing.

4. When pairing is complete the Wireless Speakers will announce ’Pairing successful’,

followed by ‘Second device connected’.

5. Now that you have paired your device with the Wireless Speakers, it will connect to it

when it is within range, which is about 10 metres or less (33 feet or less), line of sight.

6. Your device will remain paired with the Wireless Speakers unless you decide to

disconnect or ‘unpair’ it.

Note: If the pairing process is not completed within 10 minutes, your Wireless Speakers will automatically power off. Please repeat the power on and pairing steps again to complete the process.

’. Select the device name

Using your Wireless Speakers

Let’s get started

Power on

After the initial set up, when you have already paired the Wireless Speakers to each other and to a separate Bluetooth device, the announcements when you switch on the Wireless Speakers, will be slightly different.

1. Press and hold the Power On button on the top of each Wireless Speaker for about 5 seconds, until ‘Power on’, is announced, then release the power on buttons.

2. ‘Connected’, followed by ‘Left channel’, Right channel’, then ‘Second device connected’ will be announced.

Power o

1. Press and hold the Power button on one of the Wireless Speakers for about 3 seconds, until both speakers announce ‘Power off’.

luetooth mode

Check that you have connected or ‘paired’ a product with your Wireless Speakers, please refer to ‘Connecting or ‘Pairing’ with your Wireless Speakers on page 13.

Listening to Music/Audio using Bluetooth

1. Select and start the music or audio that you wish to listen to on your paired Bluetooth device, it will now be heard through the Wireless Speakers. Adjust the volume on the connected device.

2. You can use the controls on your paired Bluetooth device but you can also Play/Pause the music/audio, on your Wireless Speakers.

Press and release the power button to play/pause.

Note: If there is no audio signal for approximately 10 minutes, your Wireless Speakers will automatically power off to conserve battery power.

Using your Wireless Speakers

Let’s get started

Using as a Mobile handsfree speakerphone

If you have paired your mobile phone with your Wireless Speakers, the left channel speaker can be used as a handsfree speaker and will ring when there is an incoming call.

e an outgoing call:

Mak

1. Dial the number as usual on your mobile phone, you will be able to hear the progress

of the call and your caller through the left channel Wireless speaker and your caller will also be able to hear you.

2. Press and release the Power button on the Wireless speaker or on your mobile phone

to end the call.

Receive an incoming call:

ress and release the Power button on your Wireless speaker or answer the call

1. P

as usual on your mobile phone. You will be able to hear your caller through your Wireless Speaker and your caller will also be able to hear you.

2. Press and release the Power button on the Wireless Speaker or on your mobile phone

to end the call.

Aux in mode

our left channel Wireless Speaker can also be used in Aux in mode.

1. Connect one end of a 3.5mm audio cable (not supplied) to the headphone (or

auxiliary out) socket of your secondary device, connect the other end to the Aux in socket on the right hand side of your left channel Wireless Speaker. ‘Line in mode’ will be announced.

2. Press the Play button on your external device to start playback through the Wireless

Speaker.

3. Adjust the volume level on the secondary device.

Note: It is recommended that you unplug the audio cable from the Aux in socket

on the side of the Wireless Speaker, after you have finished listening to your external device.

Other information

Helpful technical information

Technical speciﬁcation

Audio output: 2 x 3W RMS

Voltage: Input DC 5V 1A

Lithium battery: 500mAh

Bluetooth: Version 4.1

Pairing name:

Profiles HSP, HFP, A2DP, AVRCP

Frequency range: 2.4GHz-2.480GHz

AAM

Product support

Help is always at hand

Troubleshooting

No sound / Sound distortion:

• If you are using a Bluetooth connected device, check the volume on the secondary device.

• Your Wireless Speakers may have low battery power and need to be recharged.

• Move the Wireless speakers closer together and ensure that there are no obstructions to the signal between them.

• Ensure that you are within range of the Wireless Speakers for Bluetooth functionality, 10 metres or less (33 feet or less).

• If possible, turn off other nearby WiFi / Bluetooth devices or disable their WiFi Bluetooth functionality.

• Power the Wireless Speakers off and on again.

Unable to pair with a Bluetooth device:

• Check that you are in Bluetooth mode.

• Ensure that you are within range of the Wireless Speakers for Bluetooth functionality, 10 metres or less (33 feet or less).

• Check that the device you are attempting to pair with supports A2DP stereo audio transmission.

• Move the Wireless Speakers and Bluetooth device away from other Bluetooth devices/ electrical equipment.

• If possible, turn off other nearby WiFi / Bluetooth devices or disable their WiFi Bluetooth functionality.

• Power the Wireless Speakers off and on again.

Product support

Help is always at hand

Disposal

• This product should not be treated as normal household waste and it should be recycled. Please take it to your nearest collection facility or for further details contact your local council or visit www.recycle-more.co.uk

• Batteries contain substances that may be harmful to the environment and human health. Keep out of the reach of children and seek immediate medical help if swallowed.

• Batteries should not be disposed of in the normal household waste but taken to appropriate local recycling facilities, where and when these are available.

• Never throw batteries in a fire or attempt to open the outer casing

Axess SPBP4401 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual