Axel Streamer Max MKII, STREAMER MAX ELITE MKII User Manual

Streamer Max MKII

User Manual

Audio Codec over IP-line

(Rev. Preliminary 0.0 ENG)

ENG

| INTRODUCTION

2

1 Table of Content

1. INTRODUCTION ......................................................................................................................................................... 3

1.1 STREAMER MAX MKII – VERSION AVAILABLE .............................................................................................................. 3

1.2 USE OF THIS MANUAL ............................................................................................................................................. 3

1 SAFETY WARNINGS / ISTRUZIONI PER LA SICUREZZA ...................................................................................... 4

1.1 FOREWORD ..................................................................................................................................................... 4

2 SAFETY WARNINGS ................................................................................................................................................. 5

3 CONSIGNES DE SÉCURITÉ IMPORTANTES ........................................................................................................... 6

4 ISTRUZIONI IMPORTANTI PER LA SICUREZZA ..................................................................................................... 7

5 WICHTIGE SICHERHEITSHINWEISE ........................................................................................................................ 8

6 INSTRUCCIONES IMPORTANTES DE SEGURIDAD ............................................................................................. 10

7 UNPACKING AND INSPECTION ............................................................................................................................. 12

8 FIRST INSTALLATION RECOMMENDATIONS ...................................................................................................... 13

8.1 POWER SUPPLY CABLE ................................................................................................................................ 13

8.2 FUSE REPLACEMENT ................................................................................................................................... 14

8.3 POWER SUPPLY UNIT WITHOUT FUSE REPLACEMENT ............................................................................ 15

8.4 PROTECTION AGAINST LIGHTNING............................................................................................................. 16

8.5 VENTILATION ................................................................................................................................................. 16

9 STREAMER MAX MKII – GENERAL DESCRIPTION .............................................................................................. 17

9.1 STREAMER MAX MKII – FRONT PANEL ..................................................................................................................... 17

9.2 STREAMER MAX MKII ELITE – FRONT PANEL ............................................................................................................ 18

9.3 STREAMER MAX MKII – REAR PANEL (COMMON ALSO TO ELITE) ................................................................................. 19

10 CONFIGURATION VIA WEB BROWSER ........................................................................................................... 21

10.1 HOW TO LOG IN STREAMER MAX MKII ..................................................................................................................... 22

10.2 ADMIN PAGE ....................................................................................................................................................... 22

10.2.1 How to add a new user .................................................................................................................................................. 22

10.2.2 Consideration on Username and Password .................................................................................................................. 22

10.3 ADMINISTRATION TOOLS /1 ................................................................................................................................... 23

10.3.1 User Right Management – How to change a Password ................................................................................................ 23

10.3.2 The User Right Management – How to enable/disable features .................................................................................... 24

10.3.3 How to logout a user from Streamer Max MKII ............................................................................................................ 24

10.4 ADMINISTRATION TOOLS /2 ................................................................................................................................... 25

10.4.1 Using web browser ........................................................................................................................................................ 25

11 NETWORK SETTINGS ................................................................................................................................................ 26

12 ENCODER SETTINGS ................................................................................................................................................ 27

13 DECODER SETTINGS ................................................................................................................................................ 28

14 AUDIO I/O SETTINGS ................................................................................................................................................. 29

15 SETUP SETTINGS ..................................................................................................................................................... 30

16 TECHNICAL APPENDIX ..................................................................................................................................... 31

16.1 APPENDIX A - BALANCED AUDIO CONNECTION AND PINOUT ................................................................ .. 31

16.2 APPENDIX B - SERIAL CONNECTION E PINOUT .......................................................................................... 31

16.3 APPENDIX C - ETHERNET/LAN CONNECTIONS .......................................................................................... 32

16.4 APPENDIX D - USB A/B CONNECTION .......................................................................................................... 32

16.5 APPENDIX E - GPIO PORT.............................................................................................................................. 33

17 TECHNICAL SPECIFICATION – STREAMER MAX ........................................................................................... 34

18 WEEE Directive – Informativa RAEE ................................................................................................................ 35

19 GUARANTEE ...................................................................................................................................................... 36

20 DECLARATION OF ROHS CONFORMITY ......................................................................................................... 36

21 FINAL NOTES AND AXEL TECHNOLOGY CONTACT DETAILS ..................................................................... 37

ENG

| INTRODUCTION

3

1. INTRODUCTION

1.1 STREAMER MAX MKII – VERSION AVAILABLE

MODEL

COMMERCIAL DESCRIPTION

STREAMER MAX MKII

Bidirectional Encoder/Decoder for streaming audio over IP. Analog and
AES/EBU I/O. Formats: PCM, MP3, AAC, AAC+, Vorbis, Shoutcast, Icecast.
Distributes audio over standard TCP/IP,LAN,WAN and UMTS networks with
external modem. GPIO. Audio backup on USB-HD. Unicast/Multicast.

STREAMER MAX ELITE MKII

Bidirectional Encoder/Decoder for stream ing audio over IP. Graphic display and
encoder. Analog and AES/EBU I/O. Formats: PCM, MP3, AAC, AAC+, Vorbis,
Shoutcast, Icecast. Streams audio over standard TCP/IP,LAN,WAN and UMTS
networks with external modem. GPIO. Audio backup on USB-HD.
Unicast/Multicast.

1.2 USE OF THIS MANUAL

This manual is for the Streamer Max MKII and Streamer Max MKII Elite. Certain features may be altered without prior
notice.

ENG

| SAFETY WARNINGS / ISTRUZIONI PER LA SICUREZZA

4

1 SAFETY WARNINGS / ISTRUZIONI PER LA SICUREZZA

SAFETY WARNINGS

CONSIGNES DE SÉCURITÉ IMPORTANTES

ISTRUZIONI IMPORTANTI PER LA SICUREZZA

WICHTIGE SICHERHEITSHINWEISE

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

(Rel. 1.0)

1.1 FOREWORD

For your own safety and to avoid invalidation of the warranty all text marked with these Warning Symbols
should be read carefully.

Information in this manual is subject to change without notice and does not represent a commitment on the part of the
vendor.

The manufacturer shall not be liable for any loss or damage whatsoever arising from the use of information or any error
contained in this manual, or through any mis-operation or fault in hardware contained in the product.

It is recommended that all maintenance and service on the product should be carried out by the manufacturer or its
authorised agents. The manufacturer cannot accept any liability whatsoever for any loss or damage caused by service,
maintenance or repair by unauthorised personnel.

ENG

| SAFETY WARNINGS

5

2 SAFETY WARNINGS

The installation and servicing instructions in this manual are for use by qualified personnel only.

-

Read All Instructions. All safety and operating instructions must be read before operating the product. They also
must be retained for future reference, as it contains a number of useful hints for determining the best combination of
equipment settings for Yr particular application.

-

Heed All Warnings. All warnings on the product and those listed in the operating instructions must be adhered to.

-

Heat. This product must be situated away from any heat sources such as radiators or other products (including
power amplifiers or transmitters) that produce heat.

-

Power Sources. This product must be operated from the type of power source indicated on the marking label and in
the installation instructions. If you are not sure of the type of power supplied to your facility, consult your local power
company. Make sure the AC main voltage corresponds to that indicated in the technical specifications. If a different
voltage (ex. 110/115 VAC) is available, open the equipment closure and set the voltage switch on the main supply
circuit, located behind the AC socket

-

Power Cord Protection. Power supply cords must be routed so that they are not likely to be walked on nor pinched
by items placed upon or against them. Pay particular attention to the cords at AC wall plugs and convenience
receptacles, and at the point where the cord plugs into the product

-

Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When
a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

-

Lightning. For added protection for this product during a lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the AC wall outlet and the audio connections. This will prevent damage to the
product due to lightning and power line surges

-

Installation. Configuration and installation should only be carried out by a competent installation engineer

-

Cabling. Using high quality wires, well protected. Make sure the cable integrity.

This symbol alerts you to the presence of dangerous voltage inside the closure – voltage which
may be sufficient to constitute a risk of shock. Do not perform any servicing other than that
contained in the operating instructions. Refer all servicing to qualified personnel

The exclamation point within an equilateral triangle is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature accompanying the
appliance.

Do not change the voltage setting or replace the mains fuse without first turning the unit off
and unplugging the mains cord

Make sure the AC main voltage corresponds to that indicated in the technical specifications.
THIS APPARATUS MUST BE EARTHED !

To avoid risk of fire use the correct value fuse, as indicated on the label stuck on the right
side of the unit.

This apparatus uses a single pole mains switch and does therefore not separate the unit
completely from the mains power. To completely separate from mains power (in the event of
danger) unplug mains power cord. As the MAINS plug is the disconnect device, the
disconnect device shall remain readily operable.

ENG

| CONSIGNES DE SÉCURITÉ IMPORTANTES

6

3 CONSIGNES DE SÉCURITÉ IMPORTANTES

-

Lire ces consignes

-

Conserver ces consignes

-

Observer tous les avertissements

-

Suivre toutes les consignes

-

Ne pas utiliser cet appareil à proximité de l’eau

-

Ne pas obstruer les ouvertures de ventilation. Installer en respectant les consignes du fabricant

-

Ne pas installer à proximité d'une source de chaleur telle qu'un radiateur, une bouche de chaleur, un poêle ou
d'autres appareils (dont les amplificateurs) produisant de la chaleur.

-

Ne pas annuler la sécurité de la fiche de terre, la troisième branche est destinée à la sécurité. Si la fiche fournie
ne s'adapte pas à la prise électrique, demander à un électricien de remplacer la prise hors normes.

-

Protéger le cordon d'alimentation afin que personne ne marche dessus et que rien ne le pince, en particulier aux
fiches, aux prises de courant et au point de sortie de l’appareil

-

Utiliser uniquement les accessoires spécifiés par le fabricant

-

Utiliser uniquement avec un chariot, un support ou une table spécifié par le fabricant ou vendu avec l’appareil. Si
un chariot est utilisé, déplacer l’ensemble chariot–appareil avec précaution afin de ne pas le renverser, ce qui

pourrait entraîner des blessures

-

Débrancher l’appareil pendant les orages ou quand il ne sera pas utilisé pendant longtemps.

-

Confier toute réparation à du personnel qualifié. Des réparations sont nécessaires si l’appareil est endommagé
d’une façon quelconque, par exemple: cordon ou prise d’alimentation endommagé, liquide renversé ou objet tombé
à l’intérieur de l’appareil, exposition de l’appareil à la pluie ou à l’humidité, appareil qui ne marche pas normalement
ou que l’on a fait tomber.

-

NE PAS exposer cet appareil aux égouttures et aux éclaboussements. Ne pas poser des objets contenant de
l'eau, comme des vases, sur l'appareil

Ce symbole indique la présence d'une tension dangereuse dans l'appareil constituant un risque de
choc électrique.

Ce symbole indique que la documentation fournie avec l'appareil contient des instructions
d'utilisation et d'entretien importantes.

Avant de modifier le commutateur de changement de tension ou replacer le fusible il faut

débrancher l’appareil de la prise électrique. Pendant son usage, l’appareil doit etre branchee à la

prise de terre

Utiliser le fusible principal AC avec le valeur qui est indiquée sur l'étiquette collée sur le coffret.

Assurez-vous que la tension principale AC correspond à celle indiquée dans les spécifications
techniques.

L’interrupteur d’alimentation interrompt un pôle du réseau d’alimentation excepté le conducteur

de terre de protection. En cas de danger, debrancher le cordon d'alimentation. Parce que la prise
du réseau de alimentation est utilisée comme dispositif de déconnexion, ce dispositif doit
demeuré aisément accessible

ENG

| ISTRUZIONI IMPORTANTI PER LA SICUREZZA

7

4 ISTRUZIONI IMPORTANTI PER LA SICUREZZA

-

Leggere le presenti istruzioni

-

Conservare queste istruzioni

-

Osservare tutte le avvertenze

-

Seguire scrupolosamente tutte le istruzioni

-

Non usare questo apparecchio in prossimità di acqua

-

Non ostruire alcuna apertura per il raffreddamento. Installare l’apparecchio seguendo le istruzioni

-

Non installare l'apparecchio accanto a fonti di calore quali radiatori, aperture per l'afflusso di aria calda, forni o
altri apparecchi (amplificatori inclusi) che generino calore

-

Non rimuovere il terminale di connessione a terra sul cordone di alimentazione: esso ha lo scopo di tutelare
l’incolumità dell’utilizzatore. Se la spina in dotazione non si adatta alla presa di corrente, rivolgersi ad un elettricista
per far eseguire le modifiche necessarie.

-

Evitare di calpestare il cavo di alimentazione o di comprimerlo, specialmente in corrispondenza della spina e del
punto di inserzione sull’apparato.

-

Utilizzare solo dispositivi di collegamento e gli accessori specificati dal produttore.

-

Utilizzare l’apparecchio solo con un carrello, un sostegno, una staffa o un tavolo di tipo specificato dal produttore o

venduto insieme all’apparecchio. Se si utilizza un carrello, fare attenzione negli spostamenti per evitare infortuni

causati da ribaltamenti del carrello stesso.

-

Scollegare l’apparecchio dalla presa di corrente durante i temporali o quando inutilizzato a lungo

-

Per qualsiasi intervento, rivolgersi a personale di assistenza qualificato. È’ necessario intervenire sull’apparecchio

ogniqualvolta si verificano danneggiamenti di qualsiasi natura. Ad esempio, la spina o il cavo di alimentazione sono

danneggiati, è entrato liquido nell’apparecchio o sono caduti oggetti su di esso, l’apparecchio è stato esposto alla
pioggia o all’umidità, non funziona normalmente o è caduto.

-

Non esporre a sgocciolamenti o spruzzi. Non appoggiare sull'apparecchio oggetti pieni di liquidi, ad esempio vasi
da fiori.

Questo simbolo indica la presenza di alta tensione all'interno dell'apparecchio, che comporta rischi di
scossa elettrica.

Questo simbolo indica la presenza di istruzioni importanti per l'uso e la manutenzione nella
documentazione in dotazione all'apparecchio.

Non sostituire il fusibile o cambiare la tensione di alimentazione senza aver prima scollegato il
cordone di alimentazione. L’APPARATO DEVE ESSERE CONNESSO A TERRA.

Sostituire il fusibile generale con uno di identico valore, come indicato sulla etichetta applicata
sul mobile dell’apparato

Assicurarsi che la tensione di rete corrisponda a quella per la quale è configurato

l’apparecchio

Questo apparato utilizza un interruttore di alimentazione di tipo unipolare e l’isolamento dalla

rete elettrica non è pertanto completo. Per ottenere un isolamento totale (ad esempio in caso di
pericolo), scollegare il cordone di alimentazione. Inoltre, poichè la spina di alimentazione è
utilizzata come dispositivo di sezionamento, essa deve restare facilmente raggiungibile

ENG

| WICHTIGE SICHERHEITSHINWEISE

8

5 WICHTIGE SICHERHEITSHINWEISE

-

Diese Hinweise LESEN

-

Diese Hinweise AUFHEBEN

-

Alle Warnhinweise BEACHTEN

-

Alle Anweisungen BEFOLGEN

-

Dieses Gerät NICHT in der Nähe von Wasser verwenden

-

KEINE Lüftungsöffnungen verdecken. Gemäß den Anweisungen des Herstellers einbauen

-

Nicht in der Nähe von Wärmequellen, wie Heizkörpern, Raumheizungen, Herden oder anderen Geräten
(einschließlich Verstärkern) installieren, die Wärme erzeugen

-

Die Schutzfunktion des Schukosteckers NICHT umgehen. Bei Steckern für die USA gibt es polarisierte Stecker,
bei denen ein Leiter breiter als der andere ist; US-Stecker mit Erdung verfügen über einen dritten Schutzleiter. Bei
diesen Steckerausführungen dient der breitere Leiter bzw. der Schutzleiter Ihrer Sicherheit. Wenn der mitgelieferte
Stecker nicht in die Steckdose passt, einen Elektriker mit dem Austauschen der veralteten Steckdose beauftragen

-

VERHINDERN, dass das Netzkabel gequetscht oder darauf getreten wird, insbesondere im Bereich der Stecker,
Netzsteckdosen und an der Austrittsstelle vom Gerät

-

NUR das vom Hersteller angegebene Zubehör und entsprechende Zusatzgeräte verwenden.

-

NUR in Verbindung mit einem vom Hersteller angegebenen oder mit dem Gerät verkauften Transportwagen, Stand,
Stativ, Träger oder Tisch verwenden. Wenn ein Transportwagen verwendet wird, beim Verschieben der
Transportwagen-Geräte- Einheit vorsichtig vorgehen, um Verletzungen durch Umkippen

-

Das Netzkabel dieses Geräts während Gewittern oder bei längeren Stillstandszeiten aus der Steckdose
ABZIEHEN.

-

Alle Reparatur- und Wartungsarbeiten von qualifiziertem Kundendienstpersonal DURCHFÜHREN LASSEN.
Kundendienst ist erforderlich, wenn das Gerät auf irgendwelche Weise beschädigt wurde, z.B. wenn das Netzkabel
oder der Netzstecker beschädigt wurden, wenn Flüssigkeiten in das Gerät verschüttet wurden oder Fremdkörper
hineinfielen, wenn das Gerät Regen oder Feuchtigkeit ausgesetzt war, nicht normal funktioniert oder fallen gelassen
wurde.

-

Dieses Gerät vor Tropf- und Spritzwasser SCHÜTZEN. KEINE mit Wasser gefüllten Gegenstände wie zum
Beispiel Vasen auf das Gerät STELLEN.

Dieses Symbol zeigt an, dass gefährliche Spannungswerte, die ein Stromschlagrisiko darstellen,
innerhalb dieses Geräts auftreten.

Dieses Symbol zeigt an, dass das diesem Gerät beiliegende Handbuch wichtige Betriebs- und
Wartungsanweisungen enthält.

Vor Änderung der Netzspannung oder Sicherungswechsel Netzkabel trennen.
Das Gerät muss für den Betrieb geerdet werden.

Hauptsicherung nur mit einer gleichwertigen austauschen
(s. entsprechende Etikette).

Vor Einschalten Netzspannungseinstellung am Gerät überprüfen bzw. anpassen.

ENG

| WICHTIGE SICHERHEITSHINWEISE

9

Inpoliger Netzschalter. In Notfälle oder für Wartungsarbeiten Netzkabel trennen. Der Netzstecker
fungiert auch als Trennelement muss deshalb zugänglich bleiben

ENG

| INSTRUCCIONES IMPORTANTES DE SEGURIDAD

10

6 INSTRUCCIONES IMPORTANTES DE SEGURIDAD

-

LEA estas instrucciones

-

CONSERVE estas instrucciones

-

PRESTE ATENCION a todas las advertencias.

-

SIGA todas las instrucciones

-

NO utilice este aparato cerca del agua

-

NO obstruya ninguna de las aberturas de ventilación.Instálese según lo indicado en las instrucciones del
fabricante

-

No instale el aparato cerca de fuentes de calor tales como radiadores, registros de calefacción, estufas u otros
aparatos (incluyendo amplificadores) que produzcan calor

-

NO anule la función de seguridad del enchufe polarizado o con clavija de puesta a tierra. Un enchufe polarizado
tiene dos patas, una más ancha que la otra. Un enchufe con puesta a tierra tiene dos patas y una tercera clavija con
puesta a tierra. La pata más ancha o la tercera clavija se proporciona para su seguridad. Si el toma corriente no es
del tipo apropiado para el enchufe, consulte a un electricista para que sustituya el toma corriente de estilo anticuado

-

PROTEJA el cable eléctrico para evitar que personas lo pisen o estrujen, particularmente en sus enchufes, en los
toma corrientes y en el punto en el cual sale del aparato

-

UTILICE únicamente los accesorios especificados por el fabricante

-

UTILICESE únicamente con un carro, pedestal, escuadra o mesa del tipo especificado por el fabricante o vendido
con el aparato. Si se usa un carro, el mismo debe moverse con sumo cuidado para evitar que se vuelque con el
aparato

-

DESENCHUFE el aparato durante las tormentas eléctricas, o si no va a ser utilizado por un lapso prolongado.

-

TODA reparación debe ser llevada a cabo por técnicos calificados. El aparato requiere reparación si ha sufrido
cualquier tipo de daño, incluyendo los daños al cordón o enchufe eléctrico, si se derrama líquido sobre el aparato o
si caen objetos en su interior, si ha sido expuesto a la lluvia o la humedad, si no funciona de modo normal, o si se ha
caído.

-

NO exponga este aparato a chorros o salpicaduras de líquidos. NO coloque objetos llenos con líquido, tales como
floreros, sobre el aparato.

Este símbolo indica que la unidad contiene niveles de voltaje peligrosos que representan un riesgo
de choques eléctricos.

Este símbolo indica que la literatura que acompaña a esta unidad contiene instrucciones
importantes de funcionamiento y mantenimiento.

Antes de cambiar la alimentacion de voltaje o de cambiar el fusible, desconecte el cable de
alimentacion. Para reducir el riesgo de descargas electricas, esta unidad debe ser conectada a
tierra.

Remplaze el fusible con lo mismo, que corresponde a lo indicado en el panel del equipo.

Antes de encender, controlar que la linea de alimentacion de voltaje corresponda a la indicada

ENG

| INSTRUCCIONES IMPORTANTES DE SEGURIDAD

11

El interruptor de alimentación es unipolar. En el caso de peligro, desconecte el cable de
alimentación. Porque la clavija de conexion a red sirve por la desconection de la unidad, la
clavija debe ser ubicada en proximidad de la unidad

UNPACKING AND INSPECTION

| UNPACKING AND INSPECTION

12

7 UNPACKING AND INSPECTION

Your equipment was packed carefully at the factory in a container designed to protect the unit during shipment.
Nevertheless, we recommend making a careful inspection of the shipping carton and the contents for any signs of
physical damage.

Damage & Claims

If damage is evident, do not discard the container or packing material. Contact your carrier immediately to file a claim for
damages. Customarily, the carrier requires you, the consignee, to make all damage claims. It will be helpful to retain the
shipping documents and the waybill number.

Save all packing materials! If You should ever have to ship the unti (e.g. for servicing), it is best to ship it in the
original carton with its packing materials because both the carton and packing material have been carefully
designed to protect the unit.

Under normal conditions no user maintenance or calibration are required. Internal links and preset controls may be set to
configure the unit during installation. Any service work required should be carried out by qualified service

personnel only.

We are able to offer further product support through our worldwide network of approved dealers and service agents.

To help us provide the most efficient service please would you keep a record of the unit serial
number, and date and place of purchase to be quoted in any communication regarding this
product.

The actual equipment Serial Number is indicated on the silver label stuck on the rear panel of the equipment closure.

STRM2

0E0214-001

Tools And Equipment Needed

Only standard technician’s tools are required to install this equipment.

FIRST INSTALLATION RECOMMENDATIONS

| FIRST INSTALLATION RECOMMENDATIONS

13

8 FIRST INSTALLATION RECOMMENDATIONS

8.1 POWER SUPPLY CABLE

A power supply cable of approx. 2 mt length is supplied with the device, which has a moulded IEC plug attached – this is
a legal requirement.
The type of plug for the power supply depends on the country in which it is delivered.

If for any reason, you need to use this appliance with a different plug, you should use the following wiring guidelines in
replacing the existing plug with the new one:

Earth

Green, or green and yellow

Neutral (N)

Blue

Live (L)

Brown

Supply cables should be laid in such a manner that one does not step or walk on them. They should not be squashed by
any objects.

THIS EQUIPMENT MUST BE EARTHED.

The chassis is always connected to mains earth to ensure your safety: check your mains wiring and earthing before
switching on.

CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, ALWAYS DISCONNECT THE AC
MAINS CABLE BEFORE ALTERING THE CHANGE-OVER SWITCH. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

ATTENTION: Streamer Max MKII and Streamer Max MKII Elite are provided with Universal Power
Supply. This means that the equipment could be powered with 100 – 240 Vac 50/60 Hz worldwide.

FIRST INSTALLATION RECOMMENDATIONS

| FIRST INSTALLATION RECOMMENDATIONS

14

8.2 FUSE REPLACEMENT

The power supply socket has an integral fuse drawer containing the AC power fuse and a spare, both of the same value.


BEFORE REPLACING THE POWER FUSE, MAKE SURE YOU HAVE THE RIGHT TYPE OF FUSE FOR
THE VOLTAGE TO BE PROTECTED.
USING WRONG FUSE TYPE WILL RESULT IN INSUFFICIENT PROTECTION.

Make sure that the power is switched off and the power cable is disconnected from the equipment.

a. Open the rear panel cover using a screwdriver and slide the mainboard

b. Replace the fuse located at the internal position – Power supply Type-1

Perform the set-up under static control conditions. Static charges are likely to completely destroy one or
more of the CMOS semiconductors employed in the unit. Static damage will not be covered under

FIRST INSTALLATION RECOMMENDATIONS

| FIRST INSTALLATION RECOMMENDATIONS

15

warranty.
Basic damage prevention consists of minimizing generation, discharging any accumulated static charge
on your body and preventing that discharge from being sent to or through any electronic component.

Uninsulated dangerous voltage are inside the enclosure, voltage that may be sufficient to constitute a
risk of shock.

Always disconnect to AC Mains before removing the top cover

8.3 POWER SUPPLY UNIT WITHOUT FUSE REPLACEMENT

Some new Streamer Max MKII and Streamer Max MKII Elite are provided with a new power supply unit. This power
supply does not allow a fuse replacement system, but use a Self-resetting fuse.

FIRST INSTALLATION RECOMMENDATIONS

| FIRST INSTALLATION RECOMMENDATIONS

16

8.4 PROTECTION AGAINST LIGHTNING

When the upper iron cover is removed, a plastic transparent cover helps the user safety, to avoid from flashlight coming
from the switching power supply. After the power cord has been disconnected some parts of the power supply remain
electrically loaded for a lot of time.
Axel Technology suggest to don’t touch never this parts, and it is not responsible for human flash light or electrical burns.

Should the device be put out of action due to being struck by lightning or excess voltage, disconnect it
from the power supply without delay. Do not reconnect until the device has been checked. If in doubt
contact the technical support service.

Make sure there is suitable lighting protection to protect the device.
Alternatively you should disconnect all connectors from the device during a storm or when the device
is going to be unsupervised or not used for a longer period of time.
These measures will protect against damage by lightning or excess voltage.

8.5 VENTILATION

The equipment will operate as a free-standing unit without requiring any special cooling arrangement.
However, slots and openings in the product are provided for ventilation. They ensure reliable operation of the product,
keeping it from overheating. These openings must not be blocked nor covered during operation.

YOU MUST LEAVE AT A MINIMUM ONE RACK UNIT OF EMPTY SPACE ABOVE THE EQUIPMENT TO ENHANCE
VENTILATION AND TO GET A LONGER EQUIPMENT LIFE.

STREAMER MAX MKII – GENERAL DESCRIPTION

| STREAMER MAX MKII – GENERAL DESCRIPTION

17

9 STREAMER MAX MKII – GENERAL DESCRIPTION

9.1 STREAMER MAX MKII – FRONT PANEL

N°

CONTROL NAME

FUNCTION

1

DEVICE NAMEPLATE

Plate stating product name and description.

2

STATUS POWER LED

LED that indicates if the Streamer Max MKII is powered.

STREAMER MAX MKII – GENERAL DESCRIPTION

| STREAMER MAX MKII – GENERAL DESCRIPTION

18

9.2 STREAMER MAX MKII ELITE – FRONT PANEL

N°

CONTROL NAME

FUNCTION

1

DEVICE NAMEPLATE

Plate stating product name and description.

2

LCD DISPLAY

Three-line LCD that displays the status and operation mode of the
Streamer Max MKII. It displays all the technical parameters for each
menu, also Status and Level I/O analog and digital both.

3

JOG-WHEEL or JOG SHUTTLE

Dial (or Jog Shuttle) to access the various navigation menus and
make changes. Press the Jog Shuttle to confirm selection. Accessing
this menu allows you to configure certain operating parameters for
work. All the parameters can also be set via web page.

4

HEADPHONE SOCKET

Headphone socket on the front panel, set to 6.3 mm jack, to listen
Streamer Max MKII Output. You can listen to the original audio
inserted into the audio encoder or the audio decoded by the decoder.

5

FRONT USB

Front panel USB, used to connect Flash Drive or other USB devices.

(actually not working)

STREAMER MAX MKII – GENERAL DESCRIPTION

| STREAMER MAX MKII – GENERAL DESCRIPTION

19

9.3 STREAMER MAX MKII – REAR PANEL (COMMON ALSO TO ELITE)

N°

CONTROL NAME

FUNCTION

1

POWER SUPPLY UNIT

The power supply unit features a switch to switch on the device and a
power socket. For the change of the fuse, see the relevant chapter. The
fuse is located inside the device, near the switching power supply unit.
The fuse is of the slow blow type, 230 V a.c. and 2,000 A, equal to 2000
mA. Please refer to previous page to check the exact power supply used
in the unit. Some unit are fuse-less with self resetting fuse.

2

“USB” PORT

USB -A type data communication port. This port is used to connect

devices as Serial – USB converter, or certified USB UMTS modem sim
card base.

3

ETHERNET PORT

Streamer MAX is fitted with an Rj45 Ethernet port for LAN/WAN-type
connections, to monitor and control the device. This port also provides an
integrated web server, so the Streamer MAX can be controlled remotely
using a standard web browser. The same port also features an SNMP
agent (see Appendix).

4

“DIGITAL” UNIT

This section contains the connections for AES/EBU digital outputs.
Electronically balanced

5

“DIGITAL/ANALOG” UNIT

This female connector allows two function. When the analog output it’s
selected, this connector is the Left input for Analog in. When Digital it’s
selected this connector it’s the Digital Audio Input on AES/EBU format.

6 “ANALOG” INPUT

Analog Right input over XLR balanced connector

7

“ANALOG” OUTPUT

ANALOG audio output of the Streamer MAX. Electronically balanced
output on XLR connector (type: stereo / mono)

9

“GPIO” PORT

9pin female interface on SubD connector. This shows the logic status of
the Streamer MAX. The GP outputs are Open Collector outputs, while
the GP inputs are optocouplers.

STREAMER MAX MKII – GENERAL DESCRIPTION

| STREAMER MAX MKII – GENERAL DESCRIPTION

20

For information on the GPIO Interface port pinout, see the Appendix at
the end of this manual. For the operation of each GPI and GPO, see the
specific section in the next pages of this manual.

CONFIGURATION VIA WEB BROWSER

| CONFIGURATION VIA WEB BROWSER

21

10 CONFIGURATION VIA WEB BROWSER

The Streamer Max MKII comes out programmed with a factory programmed Static IP

192.168.99.70

To configure the device via web browser Streamer Max need to set the network card on your PC class 99 and enter a
free IP that is NOT because 70 already in use. It's not possible to use the internal DHCP Web browsers supported:

- Internet Explorer 8.0

- Mozilla Firefox

- Google Chrome

- Safari
Write in the address bar the IP 192.168.99.70

Once you have found the destination of the web server will see the access mask apparatus, in Home Page. The home
page is password protected, and no action can be taken to modify the status of Streamer Max MKII

Home page provides all the necessary information as General Information, Encoder Stutus, Decoder Status and
audio level I/O.

CONFIGURATION VIA WEB BROWSER

| CONFIGURATION VIA WEB BROWSER

22

10.1 HOW TO LOG IN STREAMER MAX MKII

Streamer Max MKII web page is password protected. To access Streamer Max MKII press Login button and use this
credentials, case sensitive

Username: admin
Password: admin

Please change as soon as possible with customized Username and Password after first access
Once logged in, all the features comes available, as visible in the picture below.

10.2 ADMIN PAGE

After Login in Streamer Max MKII, by accessing the Admin page it is possible to manage users, rights and password.

10.2.1 How to add a new user

Once the Administrator is logged in, it is possible to add or remove an User by using the button +
and – as reported in the picture. After pressing + a new page appear, asking the insertion of
Username and Password, but the user must take in consideration the below condition.

10.2.2 Consideration on Username and Password

1. Be aware that the user and Admin are case sensitive

2. For the password field there are no minimal limitation

3. No complexion requirement must be reached

4. At least one character must be filled

5. No Empty password allowed

6. The total length is 50 characters

7. Backspace is a character, and considered as character

After pressing the + button this screen appear. Set the username and password and check the single function that the
Administrator wants to make available for each single user. By using the already existing functionalities it is possible to
flag and allow the user in order to use completely the function flagged. Ie: Setup – Profile Administrator – Audio.

After pressing SAVE the user is immediately created.

CONFIGURATION VIA WEB BROWSER

| CONFIGURATION VIA WEB BROWSER

23

10.3 ADMINISTRATION TOOLS /1

The Admin screen is divided in two parts: the Users and the Profile Manager. By using this control it is possible to
manage all the rights for each single user.

10.3.1 User Right Management – How to change a Password

In the left side it is possible to see the complete list of allowed users on Streamer Max MKII taken in consideration. By
pressing only one click on the User in the left, the profile manager on the right side shows all the allowed functionalities.

Once a user is selected it is possible to change the password,

by inserting a new password in the field “NEW PASSWORD”
and repeating “CONFIRM PASSWORD”. To change the field

a double click is required. In order to insert a correct
password, the Consideration on User name and Password
must be respected.

The password appears clearly in the fields, as in the picture. Once the password has been modified, the user must save

all the changes by pressing the button “Save Password”. When the password has been correctly changed a message

appears on the screen, Password Changed. By pressing OK it is possible to go on in other setup.

CONFIGURATION VIA WEB BROWSER

| CONFIGURATION VIA WEB BROWSER

24

10.3.2 The User Right Management – How to enable/disable features

In the left side it is possible to see the complete list of user allowed on the Streamer Max MKII taken in consideration. By
pressing only one click on the User in the left, the profile manager on the right side shows all the allowed functionalities.
In order to change to a single user a Rights, by simple flag (or unflag) the function on the corresponding box.

In the example above, the user Marconi Guglielmo is allowed to enter and manage the
Profile Administrator and the Setup. The user Marconi Guglielmo is not allows to CHANGE
or MODIFY Audio. To enable the single user also to CHANGE and MODIFY Tuner-1 and
Audio, by simply flag the function and press Save Rights.

The webpage will shows a message Permission Changed as reported below to confirm that the Rights has been
modified.

10.3.3 How to logout a user from Streamer Max MKII

Logout can be happen for 3 different reason, that are also reported in the table below.

N°

Condition

1

User manually press Logout

2

The user take no action for at least 60 minutes

3

Two user with same username are logged in, from 2 different position,
and one of this press logout

CONFIGURATION VIA WEB BROWSER

| CONFIGURATION VIA WEB BROWSER

25

10.4 ADMINISTRATION TOOLS /2

It is possible to download the complete Streamer Max MKII configuration in a json file using DATA Upload and
Download. Json file can be stored locally and retrieved later.

10.4.1 Using web browser

Via Web browser it is possible to download or upload a configuration, save and store in a PC as a common Json file .
Same for Access Log in TXT and same for Trap Event Log as TXT log

CONFIGURATION VIA WEB BROWSER

| CONFIGURATION VIA WEB BROWSER

26

11 NETWORK SETTINGS

By pressing this button it is possible to access and modify the value for Ethernet. Can be set IP Address, Subnet mark,
and Gateway moreover in this section can be set the Standard IP ADDRESS and a DEFAULT IP ADDRESS. Once the
modifying has been done, press “Change IP Address & Reboot” or “Change Default Address & Reboot”. The equipment
will be rebooted and after restart modifying will be applied. Same behavior for System Reboot button restart the device.

CONFIGURATION VIA WEB BROWSER

| CONFIGURATION VIA WEB BROWSER

27

12 ENCODER SETTINGS

In this page it is possible to set the Input Source for the Audio Encoder. The available sources are:

Sources available

- Analog

- Digital

- Microphone

In this page it is possible to set the Mode and parameter about the Encoder: ENCODER and DECODER parameter must
MATCH together, so if a ENCODING has been set into a mode, the same DECODING must MATCH with the Encoder.

Mode

Type

Description

Disable

Encoder Off

No encoding

RTP–UDP–PCM

Real Time Protocol, UDP, PCM

Uncompressed (linear) audio data push

RTP–UDP–MP3

Real Time Protocol, with UDP and MP3
compression

Compressed audio data push
RAW–UDP–MP3

Raw data with UDP and MP3 compression

Compressed audio data push

RTP–UDP–Opus

Raw data with UDP and MP3 compression

Compressed audio data push

IcecastSource-MP3

IcecastSource-Opus

IcecastSource-Vorbis

ShoutcastSource-MP3

IcecastServer-Vorbis

IcecastServer-MP3

IcecastServer-Opus

Each encoder mode allows different parameter selection, below are reported some

CONFIGURATION VIA WEB BROWSER

| CONFIGURATION VIA WEB BROWSER

28

13 DECODER SETTINGS

In this page it is possible to set the Mode and parameter about the decoder, ENCODER and DECODER parameter must
MATCH together, so if a ENCODING has been set into a mode, the same DECODING must MATCH with the Encoder.

Mode

Type

Description

Disable

Decoder Off

No decoding

RTP–UDP–PCM

Real Time Protocol, UDP, PCM

Uncompressed (linear) audio data push

RTP–UDP–MP3

Real Time Protocol, with UDP and MP3
compression

Compressed audio data push
RAW–UDP–MP3

Raw data with UDP and MP3 compression

Compressed audio data push

RTP–UDP–Opus

Raw data with UDP and MP3 compression

Compressed audio data push

Icecast-MP3

Icecast-Opus

Icecast-Vorbis

Icecast-AAC

Shoutcas-MP3

Shoutcast-Opus

Shoutcast-Vorbis

Shoutcast-AAC

CONFIGURATION VIA WEB BROWSER

| CONFIGURATION VIA WEB BROWSER

29

14 AUDIO I/O SETTINGS

This section allows the user to configure the audio source delivered to Streamer Max MKII audio interface module.

Analogic Output Gain: it is possible to set an Analog
output gain between -20.0 dB and 20.0 dB

Analogic Input Gain: it is possible to set an Analog
input gain between -20.0 dB and 20.0 dB

MIC Gain: Microphone gain between 0.0 dB and 60.0
dB

Digital Output Gain: it is possible to set an AES/EBU
output gain between -20.0 dB and 20.0 dB

Digital Input Gain: it is possible to set an AES/EBU
input gain between -20.0 dB and 20.0 dB

CONFIGURATION VIA WEB BROWSER

| CONFIGURATION VIA WEB BROWSER

30

15 SETUP SETTINGS

TECHNICAL APPENDIX

| TECHNICAL APPENDIX

31

16 TECHNICAL APPENDIX

This section provides all the technical explanations, and the connection pinouts to and from the Falcon XT device.
Always refer to this technical appendix for connections and connection procedures. In case of differences between the
documentation below and the hardware device, please contact Axel Technology at the numbers and e-mail addresses
shown at the end of this manual. Our technical and assistance department will be pleased to help you!

16.1 APPENDIX A - BALANCED AUDIO CONNECTION AND PINOUT

Balanced Audio connection diagram with balanced XLR for Analogue audio input and output (Left+Right) and
AES/EBU digital audio input and output.

16.2 APPENDIX B - SERIAL CONNECTION E PINOUT

PORT 1

PORT 2,3,4

2

Tx 2 Tx

3

Rx 3 Rx 4 DTR 4 / 5 GND

5

GND

A standard Pin-to-Pin serial cable is required for the PC connection, not a CROSSOVER one. For a correct connection
the cable must not be more than 20 m long. Ports 2 and 3 use only the Tx, Rx and GND for the PC connection while port
1 also has the DTR (Data Terminal Ready) for modem connection. The port connection speed must coincide with the
speed of the port of the Falcon XT and of the PC’s serial port.

2 2
3 3

4 4

5 5

RS 232 Male

RS 232 Female

TECHNICAL APPENDIX

| TECHNICAL APPENDIX

32

16.3 APPENDIX C - ETHERNET/LAN CONNECTIONS

16.4 APPENDIX D - USB A/B CONNECTION

TECHNICAL APPENDIX

| TECHNICAL APPENDIX

33

16.5 APPENDIX E - GPIO PORT

The 9 pin SubD GPIO connector on the back of the Streamer Max MKII features two General Purpose inputs and two
General Purpose binary outputs. The inputs are polarised Optocoupler inputs, while the outputs are Open Collector
outputs. They can be used to send commands to the device and to carry out specific functions. The inputs feature
polarized photo couplers on each input and a 150 Ohm protection resistor is always installed in series inside. The
maximum current that can circulate on each photo coupler is 20mA. The voltage supplied between pin 8 and pin 1 is +5
V dc non-stabilised.

TECHNICAL SPECIFICATION – STREAMER MAX

| TECHNICAL SPECIFICATION – STREAMER MAX

34

17 TECHNICAL SPECIFICATION – STREAMER MAX

PARAMETER

DESCRIPTION

Transport protocols

UDP raw, UDP/IP, TCP/IP, HTTP, RTP.

Trasmission/Reception
protocols and available bitrates

Linear WAV:

16 Bits PCM linear

OGG VORBIS:

Bitrate in kbit/sec (64, 80, 96, 112, 128,160,192) - CBR
Quality: 0(Best),1,2,3,4,5(Default),6,7,8,9(Worst) -VBR

MPEG1-L3 (MP3) (*optional)
Bitrate in kbit/sec (32, 40, 48, 56, 64, 80, 96, 112, 128,160,192) - CBR
Mode:Stereo, Joint Stereo, Dual Channel, Mono,Auto
MPEG1-L2 (MP2) (*optional)
Bitrate in kbit/sec (32, 40, 48, 56, 64, 80, 96, 112, 128,160,192) - CBR
Mode:Stereo, Joint Stereo, Dual Channel, Mono,Auto

AAC (*optional)
Bitrate in kbit/sec (32, 40, 48, 56, 64, 80, 96, 112, 128,160,192) - CBR
HEAAC, HEAACv2 (*optional)
Bitrate in kbit/sec (24, 32, 40, 48, 56, 64) - CBR

Sampling Rate

32 kHz/44.1kHz/48 kHz (Full-Duplex Mode 48kHz only)

I/O interfaces

1x Power supply interno con alimentazione universale 100-240Vac
1x Slot SD Card o SDHC
1x RJ45 full duplex IEEE 802.3 10/100Mb/s, Wi-Fi*, 3G*
2x USB 2.0 FullSpeed
2x GPInputs via Optocoupler
2x GPOut via Optocoupled open collector output
2x XLR Input: Analog / Digital (Aes/Ebu)
2x XLR Output: Analog / Digital (Aes/Ebu)
1x Graphic Display LCD (Elite Version Only)
1x Encoder with Enter button (Elite Version Only)
1x Headphone jack Output (Elite Version Only)
1x front USB 2.0 FullSpeed (Elite Version Only)

Bandwidth

20Hz – 24kHz (Analogic Sampling Rate 48Khz)

Signal-to-noise (S/N)

110 dB A-weighted (90dB nominal @ 0.0dBu sensitivity)

CrossTalk

>80 dB @ 10kHz

THD

0.005% @ 1kHz

Analog input impedance

10KOhm

Analog input sensibility

-12.0dBu to +12.0dBu

Analog max input/output

+20dBu

Digital input impedance

110Ω

Digital Input Rates

32-96 kHz with sample rate conversion and jitter correction

Input Digital Sensitivity

-30.0 dBFs, -5dBFs

Digital Output Rates

48kHz Internal or 32-48kHz Synch to AesEbu input

Digital nominal input

0.0 dBFs - -25.0 dBFs

Dimensions

217x200x44 mm (b x w x h)

Weight

2 Kg ( 3 Kg with batteries)

WEEE Directive – Informativa RAEE

| WEEE Directive – Informativa RAEE

35

18 WEEE Directive – Informativa RAEE

11In line with EU Directive 2002/96/EC for waste electrical and electronic equipment
(WEEE), this electrical product must not be disposed of as unsorted municipal waste.
Please dispose of this product by returning it to the point of sale or to your local municipal
collection point for recycling.

In Übereinstimmung mit der Richtlinie 2002/96/EG des Europäischen Parlaments
und des Rates über Elektro- und Elektronik-Altgeräte (WEEE) darf dieses Elektrogerät
nicht im normalen Hausmüll oder dem Gelben Sack entsorgt werden. Wenn Sie dieses
Produkt entsorgen möchten, bringen Sie es bitte zur Verkaufsstelle zurück oder zum
Recycling-Sammelpunkt Ihrer Gemeinde.

Conformément à la Directive 2002/96/EC sur les déchets d’équipements électriques et électroniques (DEEE), ce produit
électrique ne doit en aucun cas être mis au rebut sous forme de déchet municipal non trié. Veuillez vous débarrasser de
ce produit en le renvoyant à son point de vente ou au point de ramassage local dans votre municipalité, à des fins de
recyclage.

In navolging van richtlijn 2002/96/EG van het Europees Parlement en de Raad betreffende afgedankte elektrische en
elektronische apparatuur (AEEA) mag dit elektrische product niet als ongescheiden huisvuil worden weggedaan. Breng
dit product terug naar de plaats van aankoop of naar het gemeentelijke afvalinzamelingspunt voor recycling.

In ottemperanza alla Direttiva UE 2002/96/EC sui rifiuti di apparecchiature elettriche ed elettroniche (RAEE), questo
prodotto elettrico non deve essere smaltito come rifiuto municipale misto. Si prega di smaltire il prodotto riportandolo al
punto vendita o al punto di raccolta municipale locale per un opportuno riciclaggio.

De conformidad con la Directiva 2002/96/CE de la UE sobre residuos de aparatos eléctricos y electrónicos (RAEE), este
producto eléctrico no puede desecharse con el resto de residuos no clasificados. Deshágase de este producto
devolviéndolo al punto de venta o a un punto de recogida municipal para su reciclaje.

I henhold til EU-direktiv 2002/96/EF om affald af elektrisk og elektronisk udstyr (WEEE) må dette udstyr ikke bortskaffes
som usorteret husholdningsaffald. Bortskaf dette produkt ved at returnere det til salgsstedet eller til det lokale
indsamlingssted, så det kan genbruges.

I linje med EU-direktiv 2002/96/EG om avfall som utgörs av eller innehåller elektriska eller elektroniska produkter
(WEEE) får denna elektriska produkt inte bortskaffas som osorterat kommunalt avfall. Bortskaffa den i stället genom att
lämna in den på försäljningsstället eller din lokala återvinningsstation.

EU:n sähkö- ja elektroniikkalaiteromudirektiivin (2002/96/EY) mukaisesti tätä elektroniikkalaitetta ei saa laittaa
lajittelemattoman yhdyskuntajätteen sekaan. Hävitä laite palauttamalla se ostopaikkaan tai viemällä se
elektroniikkaromun keräyspisteeseen.

De acordo com a Directiva Europeia 2002/96/EC sobre resíduos sólidos de equipamento eléctrico e electrónico (WEEE),
este produto eléctrico não pode ser deitado fora juntamente com o lixo municipal indiferenciado. Por favor, no final da
vida útil deste produto, devolva-o ao estabelecimento de aquisição, ou entregueo no local de recolha apropriado para
reciclagem designado pelo seu município.

V souladu se smrnicí EU. 2002/96/ES o odpadních elektrických a elektronických zaYízeních (OEEZ) se tento elektrický

výrobek nesmí likvidovat jako netYídný komunální odpad. PYi likvidaci tento výrobek vrat‘te prodejci nebo ho odevzdejte

k recyklaci do komunálního sbrného zaYízení.
Vastavalt EL direktiivile 2002/96/EÜ, mis käsitleb elektri- ja elektroonikaseadmete jäätmeid (WEEE), ei või antud toodet

visata majapidamisjäätmete hulka. Palun tagastage antud toode taaskasutamise eesmärgil müügipunkti või kohaliku
piirkonna jäätmekogumise punkti.

V súlade so smernicou 2002/96/ES o odpade z elekrických a elektronických zariadení (OEEZ) sa toto elektrické

zariadenie nesmie odstranovat‘ ako netriedený komunálny odpad. Výrobok odstránte jeho vrátením v mieste nákupu

alebo odovzdaním v miestnom zbernom zariadení na recyklovanie.

GUARANTEE

| GUARANTEE

36

19 GUARANTEE

The product is covered by a one-year ex-works manufacturer’s guarantee. Do not open the device. The guarantee will
not be valid if the guarantee seals are broken. The manufacturer cannot be held liable for damages of any type deriving
from or relating to incorrect use of the product.

20 DECLARATION OF ROHS CONFORMITY

To minimize the environmental impact and take more responsibility to the earth we live, in accordance with European
Union Directive 2002/95/EC, known commonly as RoHS (Restriction of Hazardous Substances),

We herewith declare,

Axel Technology srl
Via Caduti di Sabbiuno 6/F
40011 Anzola Emilia – Bologna - Italy

that the product listed below complies with the requirements of Directive2002/95/EC, Article 4, paragraph 1 with
reference to hazardous chemical substances:

Lead (Pb)

Hexavalent Chromium
(CrVl)

Mercury (Hg)

PBB (Flame Retardant)

PBDE (Flame Retardant)

Cadmium (Cd)

Product Description: STREAMER MAX MKII

Authorized Company Representative:

Title of Signatory:

Date:

Christian Sighinolfi –
Technical Manager

28 December 2012

FINAL NOTES AND AXEL TECHNOLOGY CONTACT DETAILS

| FINAL NOTES AND AXEL TECHNOLOGY CONTACT DETAILS

37

21 FINAL NOTES AND AXEL TECHNOLOGY CONTACT DETAILS

________________________________________________________________________________________________
________________________________________________________________________________________________
________________________________________________________________________________________________
________________________________________________________________________________________________
________________________________________________________________________________________________
________________________________________________________________________________________________
________________________________________________________________________________________________
________________________________________________________________________________________________
________________________________________________________________________________________________
________________________________________________________________________________________________
________________________________________________________________________________________________
________________________________________________________________________________________________
________________________________________________________________________________________________
________________________________________________________________________________________________
________________________________________________________________________________________________
________________________________________________________________________________________________
________________________________________________________________________________________________
________________________________________________________________________________________________
________________________________________________________________________________________________
________________________________________________________________________________________________
________________________________________________________________________________________________
________________________________________________________________________________________________
________________________________________________________________________________________________
________________________________________________________________________________________________
________________________________________________________________________________________________
________________________________________________________________________________________________
________________________________________________________________________________________________
________________________________________________________________________________________________
________________________________________________________________________________________________
________________________________________________________________________________________________
________________________________________________________________________________________________
________________________________________________________________________________________________
________________________________________________________________________________________________
________________________________________________________________________________________________
________________________________________________________________________________________________
________________________________________________________________________________________________
________________________________________________________________________________________________
________________________________________________________________________________________________

Main Office BOLOGNA: Via Caduti Di Sabbiuno 6/F

40011 Anzola Emilia - Bologna - Italy

Tel. [phone] - Fax. [phone]

For Technical information or support

[e-mail]

For General information and Sales dept

[e-mail]

www.axeltechnology.com