Axel DX-1040A, EX-1040A User Manual

USER MANUAL
DX-1040A | H.264 HD/SD IRD
www.axeltechnology.com
Caution Statements:
Please observe the following safety requirements before operating the equipment.
INDEX
......................................................................................
1
1.1 Overview
.........................................................................................................
1
1.2 Features
..........................................................................................................
1
1.3 Specifications
.................................................................................................
1
1.4 Diagram
...........................................................................................................
3
1.5 Appearance and Description
.......................................................................
4
2.1 Acquisition Check
..........................................................................................
6
2.2 Installation Preparation
.................................................................................
6
2.3 Wire’s Connection
.........................................................................................
8
2.4 Signal Cable Connection
..............................................................................
9
3.1 LCD Menu Class Tree
................................................................................
11
3.2 General Setting
............................................................................................
14
Chapter 4 Web-based NMS Management
.........................................................
27
4.1 login
...............................................................................................................
27
4.2 Operation
......................................................................................................
27
Chapter 5 Troubleshooting
..................................................................................
43
1
Chapter 1 Product Outline
1.1 Overview
EX-1040A Two-Channel Professional IRD is a high-density and flexible device, integrating broadcast level receiver, demodulation, decrypting and decoding function. It supports ASI,IP and various of Tuners input which can be selected respectively from DVB-S/S2, DVB-T/T2, and DVB-C with 2* Tuner independent input, and also capable of receiving lots of programs from different frequencies.
EX-1040A is designed in standard 1U Chassis, with a Hot-Pluggable modules (can support 2 channels). Meanwhile, it delivers reliable video quality program source with advanced video decoding (H.264 & MPEG-2) technology, outputs: TS*2(backup) +IP (1*MPTS or 8*SPTS with UDP/RTP/RTSP) and monitoring. With its 2*DVB common interface slots and BISS decryption, capable of working with most of well-known CAS in the market to decrypt multiple TV pay services. With the compact design of 2*Tuner input and the excellent decoding ability, EX-1040A is becoming very popular among distribution system, IPTV applications and digital TV head-end system for DTV operators, broadcast service providers and IPTV integrators etc.
1.2 Features
Support 2*Tuner input modules selectable from DVB-T/T2, DVB-C, DVB-S/S2 Capable of demodulation, CI & BISS decryption and decoder Support HD/SD MPEG-2,H.264 video decoding, Close Caption,Subtitle and Teletext
Audio output supports MPEG 1 Layer II, LC-AAC, HE-AAC, Dolby Digital AC3
One channel Digital Dolby 5.1 surround stereo output
Support multiple programs from tuner, ASI and IP decryption via the CAM card Support 1*CVBS/YPbPr/HDMI/SDI output Support 1+1*ASI and 1*IP(1*MPTS or 8*SPTS with UDP/RTP/RTSP) multiplexing output Providing 2*LNB input and 2*LNB loop output Support auto-preserving programs Support NTSC and PAL modes available One input can support Max.128 PID re-mapping Management of support web browser via Ethernet interface Support software upgrading by Ethernet interface Power-off memory function
1.3 Specifications
TRANSPORT STREAM INPUT
2
DVB-S Tuner Input
Input Frequency Range: 950~2150MHz RF Input Level: -65~-25dBm
Symbol rate: 2~45Mbaud Convolution encoding rates: DVB-S QPSK: 1/2, 2/3, 3/4, 5/6, 7/8
DVB-S2 Tuner Input
Input Frequency Range: 950~2150MHz Symbol rate: QPSK: 1~45Mbaud
8PSK: 2~30Mbaud
Convolution encoding rates: DVB-S2 QPSK: 1/2, 2/3, 3/4, 3/5, 4/5, 5/6, 8/9,9/10
DVB-S2 8PSK: 3/5, 2/3, 3/4, 5/6, 8/9, 9/10
Constellation: QPSK, 8PSK
DVB-C Tuner Input
Standard: J.83A(DVB-C), J.83B, J.83C Input frequency: 47~860MHz Constellation: 16/32/64/128/256QAM
DVB-T/T2 Tuner Input
Connector: 2×DVB-T/T2 Tuner, F-female 75Ω Input frequency: 44~1002MHz RF Input level: -70~-20dBm Constellation: DVB-T: QPSK/16-QAM/64-QAM
DVB-T2: QPSK, 16QAM, 64QAM, 256QAM
Bandwidth: 6MHz/7MHz/8MHz FFT : DVB-T: 2K/8K
DVB-T2:1K,2K,4K,8K,16K,32K
Guard interval: DVB-T: 1/4, 1/8, 1/16, 1/32
DVB-T2: 1/4, 5/32, 1/8, 5/64, 1/16, 1/32, 1/64, 1/128
FEC: DVB-T: 1/2, 2/3, 3/4, 5/6, 7/8
DVB-T2: 1/2, 3/5, 2/3, 3/4, 4/5, 5/6
Reflection loss: 7dB (typ.)
IP Input
1*IP input for re-multiplexing (UDP Protocol)
TS Processing
1*ASI input for re-mux, BNC interface CI slots: 2×PCMCIA Slots, comply with most major CAMs in market Capable of BISS decryption
TRANSPORT STREAM OUTPUT
ASI Output
Connector: 1+1*ASI(backup), BNC Female, 75Ω Standard: DVB-ASI, EN50083-9 Output bit rate: ≤160Mb/s
IP Output
1*MPTS or 8*SPTS with UDP, RTP, RTSP 100Base-T Ethernet interface (Unicast/Multicast)
3
Video & Audio Output(for HD decoding option)
Video Decode standard: comply with HD/SD MPEG-2, H.264 Audio Decode standard:
MPEG-1 Layer II, LC-AAC, HE-AAC, Dolby Digital AC-3
Connector:
1*CVBS or YPbPr or HDMI or SDI, BNC interface.
Resolution:
480i, 480p, 576i, 576p, 720p, 1080i, 1080p
Audio Output type:
2*Stereo(4*Mono) or Digital 5.1 Surround Stereo, HDMI, SDI
GENERAL OPTION
Control & Monitoring
Connector: 1×RJ45, 10/100M, for equipment IP Control Remote Control & upgrade: Web NMS Management, USB Local interface: LCD+Control buttons
Physical and Power
Power Supply: AC100~240V 50/60Hz Consumption 20W Operational temperature: 0~45°C Storage temperature: -20~80°C Humidity: 10%-90% Dimension: (1RU,19inch),483mm(W)×340(D)mm×44mm(H) Weight: 3.0kg
1.4 Diagram
4
1.5 Appearance and Description
Front Panel Illustration:
Rear Panel Illustration
Decoder Board
1 USB upgrade port 2 HDMI video/audio output
1 LCD display for device control and configuration 2 Indicators Area (Lock 1&2: to indicate RF input signal lock status;
Decoder: to indicate the decoding status) 3 Up/Down/Left/Right Buttons 4 Enter Key
5 Menu Key 6 Lock Key
76
15
14
1312
11
10
9
8
5
4321
5
3 Component video output (YPbPr) 4 Composite video output (CVBS) 5 SDI video/audio output 6 Analog stereo audio out 1 (R/L) 7 Analog stereo audio out 2 (R/L)
Tuner Receiving
Board
8 CAMs /Smart card slots A & B 9 RF signal input and loop-through 1 & 2
10 ASI input Port for re-mux
11 ASI mirrored output ports 12 DATA Port (for IP stream input & output) 13 NMS Port (for PC connection) 14 Power switch/Fuse/Socket 15 Grounding Wire
6
Chapter 2 Installation Guide
2.1 Acquisition Check
When user opens the package of the device, it is necessary to check items
according to packing list. Normally it should include the following items:
DX-1040A 2-channel professional h.264/mpeg 2 HD IRD 1pc
User’s Manual 1pc
HDMI Cable 1pc
YPbPr Cable 1pc
CVBS Cable 1pc
SDI Cable 1pc
Audio adapt cables 2pcs
Power Cord 1pc
If any item is missing or mismatching with the list above, please contact our
company.
2.2 Installation Preparation
When users install device, please follow the below steps. The details of installation
will be described at the rest part of this chapter. Users can also refer rear panel chart
during the installation.
The main content of this chapter including:
Checking the possible device missing or damage during the transportation
Preparing relevant environment for installation
Connecting signal cables
Connecting communication port with PC
2.2.1 Device's Installation Flow Chart Illustrated as following
7
2.2.2 Environment Requirement
Item Requirement
Machine Hall Space
When user installs machine frame array in one machine hall, the distance between 2 rows of machine frames should be 1.2~1.5m and the distance against wall should be no less than 0.8m.
Machine Hall Floor
Electric Isolation, Dust Free Volume resistivity of ground anti-static
material:1X107~1X10
10
, Grounding current limiting resistance: 1M (Floor bearing should be greater than 450Kg/㎡)
Environment Temperature
5~40℃(sustainable ), 0~45℃(short time)
installing air-conditioning is recommended
Relative Humidity 20%~80% sustainable 10%~90% short time
Pressure 86~105KPa
Door & Window
Installing rubber strip for sealing door-gaps and dual level glasses for window
Wall
It can be covered with wallpaper, or brightness less paint.
Fire Protection Fire alarm system and extinguisher
Power
Requiring device power, air-conditioning power and lighting power are independent to each other. Device power requires AC power 100-240V 50-60Hz. Please carefully check before running.
2.2.3 Grounding Requirement
All function modules’ good grounding is the basis of reliability and stability of
8
devices. Also, they are the most important guarantee of lightning arresting and
interference rejection. Therefore, the system must follow this rule.
Coaxial cables outer conductor and isolation layer should keep proper electric
conducting with the metal housing of device.
Grounding conductor must adopt copper conductor in order to reduce high
frequency impedance, and the grounding wire must be as thick and short as
possible.
Users should make sure the 2 ends of grounding wire well electric conducted
and be antirust.
It is prohibited to use any other device as part of grounding electric circuit
The area of the conduction between grounding wire and device’s frame should
be no less than 25mm2.
2.2.4 Frame Grounding
All the machine frames should be connected with protective copper strip. The
grounding wire should be as short as possible and avoid circling. The area ofthe
conduction between grounding wire and grounding strip should be no less than
25mm2.
2.2.5 Device Grounding
Connecting the device’s grounding rod to frame’s grounding pole with copper wire.
2.3 Wire’s Connection
Connecting Power Cord
User can insert one end into power supply socket, while insert the other end to
AC power.
Connecting Grounding Wire
When the device solely connects to protective ground, it should adopt
independent way, say, share the same ground with other devices. When the
device adopts united way, the grounding resistance should be smaller than 1Ω.
Caution:
9
Before connecting power cord to DX-1040A, user should set the power switch
to “OFF”.
2.4 Signal Cable Connection
The signal connections include the connection of input signal cable and the
connection of output signal cable. The details are as follows:
2.4.1 DX-1040A 2-channel professional h.264/mpeg 2 HD IRD
Cables Illustration:
IP Input/output Cable Illustration:
Tuner Cable Illustration:
ASI Input/output Cable Illustration:
Video & Audio output Cable Illustration: (for connection
10
between the IRD and TV set or home theater)
CVBS Cable YPbPr Cable
HDMICable SDICable
Audio adapt cables Illustration: (for connection between the IRD
and TV set)
11
Chapter 3 Operation
The front panel of DX-1040A 2-channel professional h.264/mpeg 2 HD IRD is the
user-operating interface and the equipment can be conveniently operated and
managed according to the procedures displayed on the LCD:
Keyboard Function Description:
MENU: Cancel current entered value, resume previous setting; Return to previous
menu.
ENTER: Activate the parameters which need modifications, or confirm the change
after modification.
LEFT/RIGHT: Choose and set the parameters.
UP/DOWN: Modify activated parameter or paging up/down when parameter is
inactivated.
LOCK: Lock the screen/cancel the lock state. After pressing the lock key, the LCD
will display the current configuring state.
3.1LCDMenuClassTree
(See next page :)
12
13
14
3.2 General Setting
Switch on the device and after a few seconds’ initialization, it presents start-up
pictures as below:
HD IRD: Device’s name
Bitrate: xx.xxx MHz indicates the current effective bitrate multiplexed output.
Press LOCK key on the front panel to enter the main menu. The LCD will display the
following pages where user can configure the parameters for the device:
User could do all the settings according to the 8 directions displayed on theLCD.
User can press UP/DOWN buttons to specify menu item, and then press ENTER to
enter the submenus as below:
3.2.1 Status
Alarm: The alarm indicator will turn on if there is no A/V signals inputting or outputting
bit rate overflows. User then can enter this menu to check the error type. Otherwise it
shows the ‘system is normal’.
Start up…
DX-1040A Bitrate: xx.xxx Mbps
Start OK…
Alarm System is normal
15
Uptime: It displays the working time duration of the device. It times upon power on.
3.2.2 Input Sets
DX-1040A supports 2 tuners input, 1 ASI input and 1 IP stream input. Users can
enter ‘Input Sets’ to configure the tuner/IP parameters to receive the transport
streams and select programs to mux out. It displays as below:
Tuner DVBS/S2:
Press ENTER key to enter ‘1 Tuner DVBT/T2’ (or ‘2 Tuner DVBT/T2’), it displays as
below:
Tuner Parameters:
Users can enter this menu to configure the tuner parameters separately to receive
the tuner programs.
Mux Program:
Uptime 1 Day(s) 03:30:02
Tuner Parameters: Frequency Bandwidth Signal Lock
For checking signal status and quality etc
16
Users can parse the Tuner input program list and select program(s) to mux outin
this menu.
NOTE:
Multiplexing operation can only take effect on condition that the “TS
output mode” is set to “Mux” under ‘TS Config’. (i.e.: TS ConfigTS output
modeMux)
ASI:
Users can parse ASI input programs and select program(s) to mux out under this
menu. The operating method is same with what explained above.
IP:
Press ENTER key to enter ‘4 IP’, it displays as below:
For reading the input bitrate
TS Locked
Bitrate: 4.040 Mb
p
s
For reading the number of programs from Tuner 1 (or 2)
Searching Program
Get 7 Programs
Mux Program (0/7) 1: CCTV 1 X
Process of selecting programs to output through front panel: []: to cancel program output; []: to output the program “”: a symbol indicating the corresponding program has been selected to output; “X”: a symbol indicating the corresponding program has not been selected to output
Press ENTER key
Mux Program (0/7) 1: CCTV 1 []
Press RIGHT/LEFT key to shift arrow
Mux Program (0/7) 1: CCTV 1 []
Press ENTER key to confirm
Mux Program (1/7) 1: CCTV 1
‘1/7’ represents there are all 7 programs in the list and 1 program has been selected to mux out through ASI.
17
IP Config:
Users can enter this menu to configure IP parameters according to the IP source to
receive the IP programs.
Mux Program:
Users can parse the IP input program list and select programs to mux out in this
menu. The operating method is same with what explained above.
3.2.3 CI Card
DX-1040A supports 2 CI cards (Card A & Card B) to descramble programs from
either encrypted RF, ASI or IP. Users can press ENTER key to enter ‘CI Card’ to
configure the 2 cards respectively.
Press ENTER key to enter Card A (or Card B):
Off, V2 and V3 Optional
18
Max Bit rate
CI Max Bitrate options range from 48-108Mbps. Move the triangle to select a value
as principle: Actual Input Bitrate≤ Max Bitrate≤CI Max decrypting capacity
Input TS Mode
DX-1040A has 4 signal sources: Tuner 1, Tuner 2, ASI, and IP. One CI card can be
applied to descramble one channel input signal from the 4 signal sources. ‘Skip CI
card’ means to skip the card which is used for FTA stream.
Card Error Check
Users can decide whether to enable or disable the card error check function in this
menu.
Parse Program
Users can read the quantity of programs parsed from the de-scrambled channel.
Max Bitrate
48 Mbps
Input TS Mode
Skip CI Card
Tuner 1 Tuner 2 ASI
Card Error Check
Enable
Searching Program
Get 8 Programs
19
Descramble Program
Users can select program(s) from the searched out programs to descramble. The
quantity to be descrambled will depend on the CAM/CI performance you apply to.
Rom Version/Card Status/Descramble Error
Users can read the other info about theCIcardinthefollowingmenus.
3.2.4 BISS Descrambling
DX-1040A IRD also supports BISS to descramble encrypted programs from RF, ASI
or IP. Users can enter 2 BISS descrambling to configure the 2 BISS respectively.
Press ENTER key to enter BISS A (or BISS B):
►1 CETV 1
2 CCTV 4A X
Rom Version
X.X.X.X
Card Status
Normal
Descramble Error
Normal
20
Input TS Mode
DX-1040A has 4 signal sources: Tuner 1-2, ASI, and IP. One BISS can be appliedto
descramble one channel input signal from the 4 signal sources. ‘Skip BISS’ means
to skip the card which is used for FTA stream.
Descrambler Key/SK/Word Mode/Burned Key
Users need to input keys to descramble programs as per the BISS scrambling side
which usually is DVB-S/S2 modulator.
The descrambling principle is as following chart:
Modulating Side (BISS SCR) Receiving Side (BISS DESCR) Digit (0x----)
Mode 1+SW Data Mode 1+Descrambler Key 12
Mode E+ESW Data + Device Mode E + Descrambler Key + Burned Key 16
Mode E+ESW Data + Input ID Mode E + Descrambler Key + SK 14
TS Lock
Users can read the real-time bitrate of the corresponding channel.
Parse Program
Users can read the quantity of programs parsed from the de-scrambled channel.
Input TS Mode
Skip BISS
Tuner 1 Tuner 2 ASI IP
TS Locked
Bitrate: 34.662 Mbps
Searching Program
Get 7 Programs
21
Descramble Program
Users can select program(s) from the searched out programs to descramble.
3.2.5 TS Config
Users can press ENTER key to enter ‘TS Config’ to configure the parameters ofTS
output through ASI.
TS output mode: Enter this menu to select a TS output mode.
TS Out Bit rate: Users can set TS output bit rate in this menu.
ASI Output Select: The ASI output is copied from the one of the IP streams (MPTS
and SPTS 1-8).
►1 CETV 1
2CCTV4A X
TS output bit rat 054 Mbps
ASI output Select MPTS
22
TS ID: Users can set TS ID in this menu.
ON ID: Users can set ON ID (original network ID) in this menu.
3.2.6 Decoder
Users can press ENTER key to enter ‘Decoder’ to set the video to be decoded.
DX-1040A IRD supports one channel program to output at various interfaces at the
same time (HDMI/SDI/CVBS/YPbPr).
TS ID 00001
ON ID 0
0001
Decoder
Video Format
Audio 1 Mode Audio 1 Select Audio 2 Mode Audio 2 Select CC Enable Subtitle Tele text AC3 pass Volume Search Program Program Select Rom Version Decoder Status
23
NOTE:
Audio 1: Primary Audio Chanel; Audio 2: Secondary Audio Channel
DX-1040A supports maximum 2 channels of analog stereo audios output
simultaneously.
When the program users choose to decode and output has only one audio
channel, users need to configure Primary Audio Chanel (‘Audio 1 Mode’ and
‘Audio 1 Select’) only.
5.1 channel audio can only be resume via HDMI and SDI interfaces. When
users choose HDMI ro SDI as the output interface and output 5.1 channel
audio, users need to select ‘5.1 Channels’ under ‘Audio 1 Mode’ and set
‘Audio 2 Select’ off.
3.2.7 IP Stream
DX-1040A supports 1MPTS and 8 SPTS over IP (UDP, RTP/RTSP) output. Users
can set the IP out parameters in this menu.
3.2.8 Network
24
Users can set network parameters in this menu. Enter ‘Network’ submenus to
separately set corresponding parameters.
3.2.9 System
Users can set the system parameters in this menu. Enter ‘System’ submenus to
separately set corresponding parameters.
The IP address for connecting thedevicetoPC
NMS IP
192.168.000.136
Subnet Mask
255.255.255.000
Gateway
192.168.000.001
MAC Address 201012345678
Web NMS Port 00080
25
System Save Config Load Saved CFG Factory Reset LCD Time-out Key Password Lock Keyboard Product ID Language Version
Reset All Sets? Yes
No
Load Saved CFG? Yes
No
Save Configuration? Yes
No
Set Password 0
00000
Choose yes to save settings. and press ENTER to confirm
Choose yes to restore the device into the last saved configuration.
Choose yes to restore the device into factory’s default configuration.
Press DOWN/UP key to select a time out for the LCD lighting duration (5-120 seconds)
LCD Time-out
30 s
To set a 6-digit password for unlocking the keyboard
26
Choose Yes to lock the keyboard, then the keyboard will be locked and cannot be applicable. It is required to input the password to unlock the key board. This operation is one-off
Lock Keyboard? Yes
No
User can view the serial number of this device. It is read-only and unique
xxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxx
Language
English 中文
User can shift the system language here.
It displays the version information of this device. Encoder Modulator: the name of the device; SW: software version number; HW: hardware version number.
HD IRD
SW x.xx HW x.xx
27
Chapter 4 Web-based NMS Management
In addition to using front buttons to control the device, users can also control and set
the configuration with the web Brower in the PC.
4.1 login
The default IP address of this device is 192.168.0.136. (We can modify the IP
through the front panel.)
Connect the PC (Personal Computer) and the device with net cable, and use ping
command to confirm they are on the same network segment.
I.G. the PC IP address is 192.168.99.252, we then change the device IP to
192.168.99.xxx (xxx can be 1 to 254 except 252 to avoid IP conflict).
Use web browser to connect the device with PC by inputting the device’s IP address
in the browser’s address bar and press Enter.
It will display the Login interface as Figure-1. Input the Username and Password
(Both the default Username and Password are “admin”.) and click “LOGIN” to start
the device setting.
Fi
gure-1
4.2 Operation
Summary:
28
When we confirm the login, it displays the WELCOME interface as Figure-2 where
users can have an overview of the device’s system information and working
status.
Figure-2
Parameters → Input 1/2 (Tuner 1/Tuner 2 Input):
From the menu on left side of the webpage, clicking “Input 1” or “Input 2”, it displays
the interface where users can configure the 2 RF input parameters separately.
(Figure-3)
Figure-3
Output information of the TS and decoded program.
System informatio
User can click any item here to enter the corresponding interface to check information or set the
p
arameters.
Click “Apply” button to apply the input data to start receive si
g
nals.
ASI input
IP input
Configure RF parameters in this area according to signal source to receive programs.
RF input
29
Parameters → Input 3 (ASI Input):
“Input 3” refers to the ASI source which does not need to configure. Users canonly
read the signal lock status and input bitrate. (Figure-4)
Figure-4
Parameters → Input 4 (IP Input):
From the menu on left side of the webpage, clicking “Input 4”, it displays theinterface
where users can configure the IP input parameters. (Figure-5)
Figure-5
Click “Apply” button to apply the input data to start receive si
g
nals.
30
Parameters → CI Card:
DX-1040A supports 2 CI cards (Card A & Card B) to descramble programs from
either encrypted RF, ASI or IP. Users can click and enter ‘CI Card’ to configure the 2
cards respectively. (Figure-6)
Figure-6
CI Max Bit rate
CI Max Bitrate options range from 48-108Mbps. Select a value in the pull-down list
as principle: Actual Input Bitrate≤ Max Bitrate≤CI Max decrypting capacity.
Input TS Mode
31
DX-1040A has 4 signal sources: Tuner 1, Tuner 2, ASI, and IP. One CI card can be
applied to descramble one channel input signal from the 4 signal sources. ‘Skip CI
card’ means to skip the card which is used for FTA stream.
Card Error Check
Users can decide whether to enable the card error check function by checkingthe
box.
After configuring CI card parameters, click button to apply the input data and
then click button to parse programs from the channel selected in ‘Input
TS Mode’.
The searched out programs will be listed in the ‘Descramble’ box below: (Figure 7)
32
Figure-7
Check the program(s) to be descrambled and click button to start
descrambling the checked program(s). The program quantity to be descrambled will
depend on the CAM/CI performance you apply to.
Parameters → BISS:
33
From the menu on left side of the webpage, clicking “BISS”, it displays the interface
where users can configure 2 BISS and descramble the input channels. (Figure-8)
Figure-8
Input TS Mode
DX-1040A has 4 signal sources: Tuner 1-2, ASI, and IP. One BISS tag can be
applied to descramble one channel input signal from the 4 signal sources. ‘Skip
BISS’ means not to involve BISS function and it is used for FTA stream.
Items showing below are working as per the keys or codes set in the BISS scrambling
side (DVB-S/S2 modulators).
Input corresponding items and data to active the BISS descrambling as principles be
Modulating Side (BISS SCR) Receiving Side (BISS DESCR) Digit (0x----)
Mode 1+SW Data Mode 1+Descrambler Key 12
34
Mode E+ESW Data + Device Mode E + Descrambler Key + Burned Key 16
Mode E+ESW Data + Input ID Mode E + Descrambler Key + SK 14
After configuring the above BISS parameters, click button to apply the input
data and then click button to parse programs from the channel selected
in ‘Input TS Mode’.
The searched out programs will be listed in the ‘Descramble’ box below: (Figure 9)
Figure-9
Check the program(s) to be descrambled with “√” and click button to
start descrambling the checked program(s). The program quantity to be descrambled
will depend on the CAM/CI performance you apply to.
Parameters → TS Config:
From the menu on left side of the webpage, clicking “TS Config”, it displays the
interface where users can configure the ASI output parameters. (Figure-10)
35
Figure-10
Output TS Mode:
ASI Output Select: The TS content output through ASI is copied from the one of the
IP streams (MPTS and SPTS 1-8). Users can select one stream from the pull-down
list.
After finishing the configuration, click
to confirm.
Parameters → Mux:
Click “Mux” and it displays the interface where users can multiplex programs and
modify program info. The selected programs will output in TS form through IP and
ASI ports. (Figure-11)
36
Figure-11
Configure ‘Input Area’ and ‘Output Area’ with buttons in ‘Operation Area’. Instructions are as below:
: To enable/disable the PID remapping
To refresh the input program information
To refresh the output program information
Select one input program first and click this button to transfer the
selected program to the right box to output.
Similarly, user can cancel the multiplexed programs from the right box.
To select all the input programs
To select all the output programs
To parse programs time limitation of parsing input programs
Program Modification:
The multiplexed program information can be modified by clicking the program in the
‘output’ area. For example, when clicking , it triggers a dialog box (Figure 12)
where users can input new information.
37
Figure-12
Input new data and click ‘Save’ button at last to confirm the modification.
Parameters → PID Pass:
Figure-13
After finishing the configuration, click to confirm.
Parameters → Decoder:
DX-1040A supports decoded program to output at HDMI/SDI/CVBS/YPbPr. Users
can configure the Video/Audio output parameters in this tag. (Figure-14)
38
Figure-14
NOTE:
DX-1040A supports maximum 2 channels of analog stereo audios output
simultaneously.
When the program users choose to decode and output has only one audio
channel, users need to configure Primary Audio Chanel (‘Audio 1 Mode’ and
‘Audio 1 Select’) only.
5.1 channel audio can only be resume via HDMI and SDI interfaces. When
users choose HDMI ro SDI as the output interface and output 5.1 channel
audio, users need to select ‘5.1 Channels’ under ‘Audio 1 Mode’ and set
‘Audio 2 Select’ off.
After finishing the configuration, click to confirm.
Parameters → IP Stream:
This unit supports TS output in IP (1 MPTS & 8 SPTS). Click “IP Stream” and it
displays the interface where users can configure the MPTS & SPTS out
parameters. (Figure-15)
39
Figure-15
Parameters → Network:
Fromthemenuonleftsideofthewebpage, clicking “Network”, it will display the
screen as Figure-16 where to configure the network parameters for the device.
Figure-16
System → LCD/Keyboard:
40
From the menu on left side of the webpage, clicking “LCD/Keyboard”, it will display
the screen as Figure-17 where to control the device’s front panel.
Figure-17
System → Password:
From the menu on left side of the webpage, clicking “Password”, it will display the
screen as Figure-18 where to set the login account and password for the web NMS.
Figure-18
System → Save/Restore:
From the menu on left side of the webpage, clicking “Save/Restore”, it will display
the screen as Figure-19 where to save or restore your configurations.
41
Figure-19
System → Backup/Load:
From the menu on left side of the webpage, clicking “Backup/Load”, it will display
the screen as Figure-18 where to backup or load your configurations.
Figure-20
System → Firmware:
From the menu on left side of the webpage, clicking “Firmware”, it will display the
screen as Figure-19 where to update firmware for the device.
42
Figure-21
System → Reboot:
From the menu on left side of the webpage, clicking “Reboot”, it will displaythe
screen as Figure-22 where to restart the device manually.
Figure-22
43
Chapter 5 Troubleshooting
Axel technology’s ISO9001 quality assurance system has been approved by CQC organization.
For guarantee the products’ quality, reliability and stability. All Axel technology products have
been passed the testing and inspection before ship out factory. The testing and inspection
scheme already covers all the Optical, Electronic and Mechanical criteria which have been
published by Axel technology. To prevent potential hazard, please strictly follow the operation
conditions.
Prevention Measure
Installing the device at the place in which environment temperature between0to45°C
Making sure good ventilation for the heat-sink on the rear panel and other heat-sink bores if
necessary
Checking the input AC voltage within the power supply working range and the connection is
correct before switching on device
Checking the RF output level varies within tolerant range if it is necessary
Checking all signal cables have been properly connected
Frequently switching on/off device is prohibited; the interval between every switching on/off
must greater than 10 seconds.
Conditions need to unplug power cord
Power cord or socket damaged.
Any liquid flowed into device.
Any stuff causes circuit short
Device in damp environment
Device was suffered from physical damage
Longtime idle.
After switching on and restoring to factory setting, device still cannot work properly.
Maintenance needed
Loading...