Page 1
60W Sound Pack
Installation
AXCITY
ZAC des Hauts de Wissous
« Air Park de Paris »
Bâtiment le Cormoran
3 rue Jeanne Garnerin
91320 Wissous, France
ASBSOP0201-n°1
2012
Page 2
Contents
60W Sound Pack Installation
Chapter 1
Pack Description
Box Contents ......................................................... 1-1
60W Amplifier ....................................................... 1-2
100V Speakers ....................................................... 1-3
Speaker Cable ....................................................... 1-4
Chapter 2
Pack Implementation
Step 1
Speakers Connection ............................................. 2-5
Step 2
AM/FM Antenna Connection ................................. 2-8
Step 3
Power Cord Connection ......................................... 2-9
Step 4
Amplifier Start-up ................................................ 2-10
Page 3
Chapter 3
Quick Troubleshooting
60W Pack ......................................................................... 3-12
Appendix A
Technical Data Sheets
Appendix B
Associated Documents
Page 4
Pack Description 1-1
Chapter 1
Pack
Description
Box Contents
The 60W Sound Pack contains the following: items
• 1 60W amplifier with USB/CD/Tuner
• 6 6W/100V speakers
• 1 AM/FM antenna
• 1 power cord
• 100 meters of speaker cable
If any of these are incorrect, missing, or damaged,
contact your Axcity dealer. Keep the original box and
packing materials, in case the product needs to be sent
back for repair.
Page 5
Pack Description 1-2
60W Amplifier
General Description
3-zone mixer amplifier equipped with an AM/FM tuner
and a CD MP3/USB player. The volume control covers all
areas. It can also be used at full power in single zone
mode. Its LCD screen provides the view of the radio
station or CD/USB title playing. Tuning radio stastion is
accomplished automatically using the scan function.
Page 6
Pack Description 1-3
100V Speakers
General Description
6W/100V speaker. Wideband, it has an excellent audio
quality. Its small diameter provides a discrete
installation in the ceiling.
Page 7
Pack Description 1-4
Speaker Cable
General Description
Flat loudspeaker cable dedicated to the 100 volt line.
Suitable for all types of sound systems, it can be used
both in fixed and mobile installations.
Page 8
Pack Implementation 2-5
Chapter 2
Pack Implementation
Step 1: Connection of the speakers to the
amplifier
Beforehand, you must connect the speakers to speaker cables.
Then connect the speaker cable(s) to the amplifier.
General view of the rear of the amplifier
Start by stripping each conductors about 5 mm.
Page 9
Pack Implementation 2-6
Fig.1
Unscrew the COM terminal on the right. Insert the black
conductors into the space between the connection plate
and the fixed terminal.
Screw up the COM terminal.
Page 10
Pack Implementation 2-7
Insert the red conductors into the SP1 terminal,
corresponding to the 1st zone. The SP2 and SP3 terminals
correspond to zones 2 and 3.
Note:
- 1 wired zone: 60W output power
- 2 wired zones: 20W output power
- 3 wired zones: 20W output power
Page 11
Pack Implementation 2-8
Step 2: Connection of the AM/FM antenna to
the amplifier
fig.2
Connect a conductor to the GND terminal.
Connect the other conductor to the 75Ω terminal.
Page 12
Pack Implementation 2-9
Step 3: Connection of the power cord to the
amplifier
fig.3
Plug the power cord into the outlet provided for that
purpose.
Turn the amplifier on.
Page 13
Pack Implementation 2-10
Step 4: Starting the Amplifier
Press the “POWER” button, after checking that the
“MASTER” button is on “0”.
Select the zone(s) for distribution.
Page 14
Pack Implementation 2-11
The red LED lights to indicate the amplifier is powered
up.
In order to access to the AM/FM tuner as well as the
CD/MP3 and USB player, press the “sound volume”
button. Select the desired source.
To turn off, press and hold.
Page 15
Quick Troubleshooting 3-12
Chapter 3
Quick Troubleshooting
The 60W pack does not work
If the red LED on the amplifier is not lit:
Check that the power supply unit is functioning
properly.
Check that the speakers are properly connected to each
other and to the amplifier. To do so, press the CHIME
button. If sound comes out of the speakers, that means
the 100V line is working properly. Therefore, the
problem must have a different source. If no sound
comes out of the speakers, check that the amp’s master
button is pressed.
Page 16
APPENDIX A
APPENDIX A
Technical Data Sheets
60W Amplifier
Technical Specifications
RMS output power
1 x 60W (3 x 20W)
Bandwidth
80 Hz – 15 kHz
Signal/noise ratio – MIC
> 70 dB
Signal/noise ratio – LINE
> 60 dB
Distortion Ratio
< 1% @ 1 kHz
MIC Inputs
Symmetric 3 mV
LINE inputs
300 mV
PHONE Inputs
2.40 mV
Speaker Outputs
70, 100 / 4 and 8 Ohm
Power Supply
240 VAC – 50/60 Hz 24 VDC
Dimensions
420 mm x 110 mm x 320 mm
Weight
10 kg
Page 17
APPENDIX A
100V Speaker
Technical Specifications
Speaker Size
3”
Frequency Response
120 Hz – 20 kHz
Rated Power
6 W RMS
Nominal SPL (1W / 1M)
91 dB
Max. nominal SPL (6W /
1M)
99 dB
Directive
89°
Power selection by wiring
3 – 6
6W / 8Ω
Mounting Type
Ceiling
Colour
White / RAL 9016
Cross-section
Ø 95 mm
Dimensions
103 mm x 80 mm
Weight
0.22 kg
Page 18
APPENDIX A
WWAARRNNIINNGG::
In order to avoid electrical shock hazards, do
not remove the cover. No maintenance of internal parts
must be done by users, contact qualified personnel. If
necessary.
NNOOTTIICCEESS::
In order to avoid fire and electric shock
hazards, do not expose this product to rain or moisture.
Page 19
APPENDIX B
APPENDIX B
Associated Documents
This appendix provides links to reference documents
that can help you to understand better the technologies
used for your Axcity product.
Documents
Link
Amplifier Technical Data
Sheet
Amplifier User Manual
Speaker Technical Data
Sheet
www.axcity.fr
www.axcity.fr
www.axcity.fr
Loading...