Axcera 79XITS-7042 User Manual
ADC
Telecommunications
TECHNICAL MANUAL
EXHIBIT II
(PRELIMINARY)
ITS-605C
BROADBAND
BOOSTER
REV: 0
102 Rahway Road
McMurray, PA 15317 USA
Phone 412-941-1500
FAX 412-941-9421
ITS-605C
BROADBAND BOOSTER
TABLE OF CONTENTS
I. INTRODUCTION:
II. SYSTEM ITS-605C:
A. SYSTEM DESCRIPTION
B. SPECIFICATIONS
C. INSTALLATION PROCEDURE
III OPERATION ITS-605C:
A. CONNECTIONS
B. INITIAL TURN ON
C. UNIT OPERATION
D. INTERNAL LED INDICATORS
E. MAINTENANCE
IV BROADBAND BOOSTER AMPLIFIER SYSTEM:
BLOCK DIAGRAM
INTERCONNECT
V BROADBAND BOOSTER TRAY:
BLOCK DIAGRAM
INTERCONNECT
BROADBAND BOOSTER TRAY SUBASSEMBLIES
...........................................................................................................................
..............................................................................................................................
...........................................................................................................................
..............................................................................................................................
1576-3000
1576-8000
1576-3100
1576-8100
ITS-605C
SYSTEM DESCRIPTION
The ITS-605C Boradband Booster is a wideband linear amplifier intended to be used as a booster in the
MMDS/ITFS frequency bands, from 2500.00 to 2569.00 MHz, which allows the unit to operate with up to
thirty one 6 MHz channels. The power capability of the unit varies with the number of channels according
to specifications. The 605C is packaged in a weatherproof aluminum outdoor enclosure and uses an
external convection cooled design.
The 605C includes a preamplifier, power supply, and mounting hardware. . A multi-channel RF input
signal enters the system at the broadband booster tray's RF input where it is filtered and amplified. The
broadband booster tray also incorporates automatic level control to maintain the combined output power
within the limits of the output amplifiers and all the necessary control logic of the system.
SPECIFICATIONS: ITS-605C Broadband Booster
Type of Emissions
Frequency Range
DC voltage and total current of final amplifier stage
Output Power Rating
Performance Specifications
Operating Frequency Range
RF Output - Nominal:
Impedance
Connector
Power (average):
Nominal Input Signal Range
Connector
Impeadance
........................................................................................
..............................................................................
............................................................................................
4 Channel
8 Channels
12 Channel
16 Channels
24 Channel
31 Channels
BOOSTER
2500 to 2569 MHz
..................
(Class A - Not RF power dependent)
..............................................................
..............................................................
...............................................................................................
...................................................................
...............................................................
.................................................................
................................................................
.................................................................
..................................................................
........................................................
...........................................................................................
.............................................................................................
10 volts DC at 5.48 amps
1.5 watts (peak envelope)
(250 mW total average)
2500 to 2569 MHz
Type N
62.5 mW/channel
31.25 mW/channel
20.8 mW/channel
15.6 mW/channel
10.4 mW/channel
8.0 mW/channel
-83 to -53 dBm/channel
Type N
50
50
Ω
Ω
Out-of-Band Power
-25 dB max (at band edges):
-40 dB max (250.00 KHz above and 250.00 KHz below band edges):
-50 dB max (3.00 MHz above and 3.00 MHz below band edges):
-60 dB max (20.00 MHz above and 20.00 MHz below band edges):
Out-of-Band Power (Unoccupied Channel)
-40 dB max (250.0 KHz above and 250.0 KHz below occupied channel edges):
-50 dB max (3.0 MHz above and 3.0 MHz below occupied channel edges):
Harmonic Products
Electrical Requirements
Power Line Voltage
Power Consumption
..................................................................
.....................................................................................
.................................................................
.......................................................................................
Per FCC Rules (21.908)
-25 dB max (at unoccupied channel edges)
.....
-60 dB max
60VAC, ±10%, 50/60 Hz
260 Watts
Loading...