Instruction Manual
For your safety, please turn off power to both the controller and drone before handling.
Power Indication Light
Forward/Backward
Fine Tuning
Side-Fly
Fine Tuning
360 Flips Button
Power Switch
Rudder Power Fine Tuning
Left Operating Lever
(Acceleration, Turning)
Right Operating Lever
(Forward/Backward, Side-Flying)
Power Indication
Forward/Backward
Fine Tuning Indication
Side-Fly
Fine Tuning Indication
Take Photo
Liquid Crystal Display
Headless
Mode
Light Control
Channel and Rudder
Power Monitor
Light
Take Video
Remote Control
Signal
Take Video
Motor
Blade
Protective
shell
Protective
guards
1. Parts
2. Installing Remote Controller Batteries
Open the battery cover on the back of remote controller. Insert four AA alkaline batteries at the correct
polarity. Close battery cover.
(Batteries not included, do NOT mix old and new batteries.)
Battery cover
4 AA Batteries
Screw position Screw position
5. Preparing for Take Off
3. Assembling the Quadcopter
4. Recharging the Battery
1. Insert and attach the Landing Feet to the bottom of the Quadcopter. Fasten the screws using the
screwdriver into the screw holes to secure the Feet in place.
2. Insert and attach the Protective Guards to the Quadcopter. Fasten the screws using the screwdriver
into the screw holes to secure the Guards in place.
1. Please fly the Quadcopter in a spacious indoor area, or outdoors in nice weather. Keep clear of
people, a n imals, or obstacles to prevent injury or damage.
2. Insert the provided Li-po battery into the Quadcopter and turn on. The indicator light will begin
fla s h i n g . Place the Quadcopter on a f l a t l evel sur face and begin syncing with the rem o t e c o n t roller.
3. To sync the controller with the Quadcopter, first pull the left acceleration lever to its lowest position.
Now turn on the remote controller and push the lever to its highest position. Once again, pull the
lef t lever to i t s l o west position. There wi l l b e a b e e p a n d Q u a d c o p ter's indication light s w i l l t urn on.
The Qua d c opter and the re m o t e are now synced and you are r e a d y for take of f!
Insert the provided USB cable into a computer's USB socket and the red indication light will turn on. Now
connect the USB cable to the battery's cable or into the Quadcopter's charging port. The indicator light
will turn off and begin charging. When the red light turns on again, the battery is fully charged. Charging
time can take up to 100 minutes.
Insert the USB cable into the
charging port at the bottom of the
quadcopter
Insert the USB cable into the Battery's cable.
7. Headless Mode and One Key Return
6. Controls and Fine Tuning
Turning
Forward/
Backward
Forward/
Backward
Fine Tuning
Side-Flying
Side-Flying
Fine Tuning
Headless Mode: Press the Headless Mode button and you will hear the controller begin to beep, indicating it has
entered Headless Mode. No matter what direction the quadcopter faces, it will respond according to the direction
pushed on the remote. (Forward on the remote will make the quadcopter fly forward.) This makes flying simpler
and more convenient for beginner pilots. To exit Headless Mode, press the button again and you return to Normal
Mode.
When the Quadcopter deviates too much, the player can re-adjust the balance to improve the Quadcopter’s
flight. Place the Quadcopter on the level floor, then slightly press the 360 flips button on the remote controller’s
upper-right side. Simultaneously push the two operation levers to the bottom-left and hold for 3 seconds. Release
the operation levers after the indication light of the Quadcopter begins flashing. Wait about 2 seconds until the
indication light turns constant and the balance re-adjustment is finished.
One Key Return: As long as you are in controllable range, press the One Key Return button on the remote. You
will hear a single beep and the quadcopter will automatically return to the pilot. Press the button again or push
the control lever to exit One Key Return.
This Quadcopter has been specially designed to prevent it from crashing into an insecure or dangerous area due
to low battery power. When the battery power begins to become insufficient, the indicator light will turn from
constant to flashing. The pilot will have enough time to fly the Quadcopter back and change the battery or
recharge it for the next flight.
Ascending/
Descending
Mov e t h e lef t o p e rating leve r u p a n d d own to make
the Q uadcopter ascend and descend.
When t h e Q u a d c o p t er is hoverin g , a n d i t d eviates
forward or backward, turn the forward/backward fine
tu n i n g u p or d own until the Quad c opter hov e r s
balanced.
When t h e Q u a d c o p t er is hoverin g , a n d i t d eviates lef t
or r i ght, turn the s i de-flying fine tuni n g t o t h e l ef t o r
right u n t il the Quadcopter hove r s b a lanced.
Mov e t h e ri ght operating lev er lef t a n d r i ght to make
the Q uadcopter fly lef t and fly right.
Mov e t h e ri ght operating lev er up and down to make
the Q uadcopter fly fo r ward and fly backward.
Mov e t h e lef t o p e rating leve r l e f t a n d r i g h t t o make
the Q uadcopter tur n l e f t and turn right.
LED state light
Problem Cause
Solution
8. 360 Flips
9. Shooting Pictures and Video
10. Troubleshooting
Tap the 360 Flips button. The indication light on the Quadcopter will begin to flash and the remote controller will
beep continuously. Fly the Quadcopter to a safe height of 6 feet and push the right operation lever in any
direction and the Quadcopter will roll in that corresponding direction.
1. Insert the SD card into the back of the camera, then attach the camera to the Quadcopter as shown in the
picture below. Insert the camera's plug into its port on the bottom of the Quadrone.
2. Press the Photo button on the remote controller. The red light will flash once, indicating it is taking a picture.
By pressing the Video button, the red light will stay constant, meaning the camera is filming video. Press the
Video button again to stop recording. The red light will turn off, indicating the recording is finished.
3. Softly press the SD card to eject it from the camera. Insert it into a card reader and plug it into a computer to
see your pictures and videos!
Tips:
1. Press the Video button again to save the video after
you are done shooting.
2. An AVI format should be compatible to view on
video playing software.
3. The red indicator light will flash rapidly when the SD
card is not inserted correctly, or the memory is full.
The indication light on the
Quadcopter is flashing and it is
not reacting to remote controller.
1. Quadcopter and remote are not
properly synced.
2. Low battery power
1. Refer to Prepare for Take Off
and re-sync.
2. Recharge battery
Quadcopter cannot keep balance
after fine tuning.
1. Blades are distorted
2. Motor doesn't work properly
1. Replace blades
2. Replace motor
Quadcopter lost control after
crashing
3 axis acceleration sensor lost its
balance after crashing
Put Quadcopter on the ground
for 5-10 seconds and re-sync.
Quadcopter shakes hard. Blades are distorted Replace blades
Quadcopter's blades turn but
cannot take off.
1. Blades are distorted
2. Low battery power
1. Replace blades
2. Recharge battery
11. Accessories (Optional)
1. Upper Cover 2. Lower Cover 3. Clockwise Blades
(Serial Letter A)
4. Reverse Blades
(Serial Letter B)
5. Counter-Clockwise
Motor
(Red Blue Line)
6. Reversal Motor
(Black White Line)
7. Battery 8. Receiver Board 9. USB Charging Cable 10. Camera
11. Gear Accessory 12. Protective Guard 13. Landing Feet 14. Light 15. Philip's Head
Screwdriver
AWW INDUSTRIES™ is an innovative division of DGL Group, Ltd.
Other trademarks and trade names are those of their respective owners.
AWW INDUSTRIES,
195 Raritan Center Parkway, Edison, NJ 08837.
Specifications, colors and contents may vary from illustrations.
WARNING: This product may
contain a chemical known to
the State of California to cause
cancer, or birth defects, or
other reproductive harm.
PROP 65 WARNING
Manufactured in China.
Batch Ref: XXXX
Model Number: XXXX
Conforms to safety requirements of ASTM, FCC, & CPSIA.
WARNING:
CHOKING HAZARD-Small parts.
Not for children under 3 years.
Tested to compl y with FCC standards .
FOR HOME OR O FFICE USE.
This devic e complies with pa rt 15 of the FCC
Rules. Op eration is subje ct to the followi ng two
conditions:
(1) This device may not c ause harmful
interference and
(2) This device m ust accept any inter ference
received, including interference that may cause
undesired operation.
BATTERY WARNING:
• Do no mix alkaline, standard (carbon zinc), rechargeable (nickel hydride) batteries.
• Do not mix old and new batteries.
• Non-rechargeable batteries should not be recharged.
• Rechargeable batteries should be removed from the appliance before being charged.
• Rechargeable batteries should be charged under adult supervision only.
• Exhausted batteries should be removed.
• The supply terminals should not be short-circuited.
• Only batteries of the same or equivalent type are recommended to be used.
• Batteries should be inserted with the correct polarity.
Loading...