AWW quadrone XLC Instructional Manual

Instructional Manual

1. The vice-blade steering engine can be divided into levels of 25%, 50%, 75%, and 100%
rudder power. The user can select any one of these levels according to their ying experience.
The default rudder power is 25% when the power is turned on. The remote control has
two types, one with an LED screen and one without. Even without the LED screen, the user
can distinguish the rudder power by listening to the indicator beep.
1 beep = 25%, 2 beeps = 50%, 3 beeps = 75%, 4 beeps = 100%.

Parts

1. Parts

Open the battery cover on the back of the remote controller. Insert four AA alkaline
batteries in accordance with the instructions on the battery box. (Battery should be
purchased separately. Old and new batteries should not be mixed.)

Insert the included charger into an electrical power source. The indication light
will turn green, then connect it to the battery. When the light turns red, the battery
has begun to charge. Charging time is about 100 minutes.

1. Please operate in a spacious indoor area or outside in clear weather. Do not y in
high winds. Fly away from people, animals, and other obstacles.

2. Insert the Li-po battery included into the quadcopter. When the indication light on the
quadcopter begins to ash, place the quadcopter on a level surface and wait for the
frequency to adjust.

3. Pull the acceleration lever all the way back and turn on the remote control. Push the
acceleration lever all the way forward and pull it back again all the way back. There will be
a beep and the quadcopter’s indication light will turn on. The frequency adjustment is
complete and you are ready for take o.

2. 3D mode is the button that puts the quadcopter into 3D roll over mode. The mode has two
kinds, indoor mode and outdoor mode. Hold the button for 5 seconds to switch between
the two modes. Two beeps means indoor mode and four beeps means outdoor mode.
The user can switch between the two modes according to their playing condition.
The default mode is the indoor mode, but the controller has a memory function to continue
to use the mode it used previously, even if the batteries are removed.

4

2. Inserting Batteries

3. Charging the Quadcopter’s Batteries

Get Ready for Take Off

The user can switch between indoor and outdoor mode according to the ight condition.
No matter the mode, the remote control’s indication light will ash when the 3D mode button
is pressed. After ascending the quadcopter to 6 feet, pull the right operating lever to the
bottom in any direction and then release it. The quadcopter will then roll over. Repress the 3D
mode button in order to exit.

When the left operating lever is pushed up and pulled down,
the quadcopter will ascend and descend.

When the left operating lever is pushed left or right,
the quadcopter will turn left or right.

When the right operating lever is pushed up or down,
the quadcopter will go forward or backward.

When the right operating lever is pushed left or right,
the quadcopter will y left or right.

When the quadcopter is hovering and the head of the
quadcopter turns left or right, turn the ne tuning to the left
or the right in order to balance the quadcopter.

When the quadcopter is hovering and the quadcopter is
deviating to the left or the right, turn the side-ying ne
tuning to the right or left in order to balance the quadcopter.

When the quadcopter is hovering and the quadcopter is
deviating forward or backward, turn the forward/backward
ne tuning up or down in order to balance the quadcopter.

4. Basic Flying and Fine Tuning

5. Flips

Considering dierent places and spaces of operation, this quadcopter is designed
with two kinds of protection covers which, along with the speed adjustments, will
help make the quadcopter y perfectly in both indoor and outdoor conditions.

1. Indoor Mode: When ying indoors, the narrow spaces and obstacles may make
ight more dicult. Users can more easily operate the quadcopter by attaching the
big protection cover and a low to mid ight speed.

2. Outdoor Mode: When ying outdoors, the winds and excitement might require a
higher power and faster speed. Users can remove the indoor protection cover and
y at a mid to high speed to enjoy a faster and more exciting ight.

1. To prevent the quadcopter from descending into an unsafe area due to insucient
battery power, it is designed with a power warning function. When the battery power
is low, the LED light will turn from constant to ashing. The user will then have time to
y the quadcopter back and recharge the battery.

2. When ying outdoors, please make sure the remote control is in outdoor mode in order
to guarantee a normal 3D roll over.

This quadcopter was originally designed with a model plane’s operation mode. As a

result, operating the quadcopter is more dicult than usual. To reduce any learning

curves for new players, this quadcopter has been designed with a new and

mass-oriented operation mode called New Player’s Mode.

Keep pressing any key on the upper left or upper right of the remote control and turn

on the remote control’s power. Release the button and the New Player’s Mode is now

selected. In New Player’s Mode, the functional keys for the remote control are

distributed according to the diagram on the following page:

5. Indoor and Outdoor Mode

6. New Player’s Mode

1. Press the video button again to save the video
when nished shooting.

2. An AVI form should be compatible to the video
playing software.

3. The red light indicator will be ashing quickly
when the SD card is not inserted or full.

Tips:

1. Insert the SD card into the webcam’s card channel, then attach the module to the
bottom of the battery box as shown in the picture. Open the upper cover and take out
the webcam’s plug and insert it into the red video shooting outlet of the circuit board.

2. Press the photo mode button on the remote control and the red light will ash once,
meaning the quadcopter is taking a photo. By pressing the video mode button the red
light will stay on, meaning the quadcopter is taking a video. Press the button again in
order to stop taking video.

3. Slightly press the SD card to take it out. Insert the card into the card reader and insert the
reader into a USB outlet in order to view the photos/videos.

Left Side Flying Button

Power Button

Right Side Flying Button

Forward Roll Over

Right Side Roll Over

Backward Roll Over

Left Side Roll Over

Left Operating Lever

(Accelerator, Side Flying)

Right Operating Lever

(Forward/Backward, Turning)

Take Photo

Light Control Button

Take Photo

Rudder Volume

Fine Tuning

7. Shooting Photos and Video

The quadcopter shakes hard.

The ne tuning buttons are all on but
the quadcopter still can’t keep balance.

The quadcopter is out of control after
having crashed.

The quadcopter can’t take o vertically
in normal conditions.

The indication light of the quadcopter
is ashing and the quadcopter does
not react to operation.

The quadcopter’s blades turn but it
cannot take o.

The blades are distorted.

1. The blades are distorted.

2. The motor doesn’t work properly.

Three-axis acceleration sensor has lost
its balance after crashing.

The quadcopter is not adjusted to the level.

1. Frequency modulation between the
quadcopter and remote control is not
operating correctly.

2. Insucient battery power.

1. Insucient battery power.

2. The blades are distorted.

Replace the blades.

1. Replace the blades.

2. Replace the motor.

Put the quadcopter on the ground for
5-10 seconds.

Put the quadcopter on the leveled are
or desk. Keep pulling both the left and
the right operating levers to the bottom
left until the indication light on the
quadcopter ashes. Release the two levers
and the indication light will turn to
constantly on.

1. Refer to Prepare for Take O and
remodulate the frequency.

2. Recharge the battery.

1. Recharge the battery.

2. Replace the blades.

SolutionReasonProblem

1 indoor shell 2 outdoor shell 3 Clockwise

Blades

(serial number A)

6 Reversal Motor 7 Battery 8 Receiver Board 9 Battery Charger 10 Webcam Kit

(Black White line) (F182C)

4 Reversal

Blades

5 Counter-clockwise

Motor

(serial number B) (Red Blue line)

8. Troubleshooting

9. Optional Accessories

AWW INDUSTRIES™ COPYRIGHT © ALL RIGHTS RESERVED.
No portion of this package, including shape, graphics, and design may be reproduced or
transmitted in any form or by any means, electronic or mechanical, including by photocopy­ing, recording or use of any information storage and retrieval system without express written
permission. Unauthorized reproduction or distribution of this package, design or any portion
of it will be prosecuted to the maximum extent possible under law.

AWW INDUSTRIES™ is an innovative company of DGL Group, Ltd.
Other trademarks and trade names are those of their respective owners.

AWW INDUSTRIES,
195 Raritan Center Parkway, Edison, NJ 08837.

Specifications, colors and contents may vary from illustrations.

WARNING: This product may
contain a chemical known to
the State of California to cause
cancer, or birth defects, or
other reproductive harm.

PROP 65 WARNING

Tested to compl y with FCC standard s.
FOR HOME OR O FFICE USE.
This devi ce complies with pa rt 15 of the FCC
Rules. Op eration is subje ct to the follow ing
two conditions:
(1) This device may not c ause harmful
interference and
(2) This devi ce must accept any inter ference
received, including interference that may
cause undesired operation.