AWS SM-200, SM-500, SM-501, SCALE MATE SM-500DR, SCALE MATE SM-200 User Manual

...
Page 1
American Weigh Scales, Inc.
User Manual
D i g i t a l P o c k e t S c a l e
SCALE MATE
200gX0.01g
SM-200 (200 x 0.01g) SM-500 (500 x 0.1g) SM-501 (500 x 0.01g) SM-500DR (100x0.01g/500x0.1g)
Page 2
American Weigh Scale Mate
Thank you for purchasing the American Weigh Scale Mate digital pocket scale. Please read all operating instructions carefully before use. This electronic scale is a precision instrument. With normal care and proper treatment, it will provide years of reliable service. Never load the scale with more than the maximum capacity. Overloading will permanently damage it! Avoid any exposure to extreme heat or cold. Your scale works better when operated at normal room temperature. Always allow the scale to acclimatize to normal room temperature for at least one hour before use.
Give your scale sufcient warm up time. Usually
30-60 seconds before calibration to give the internal components a chance to stabilize. Keep your scale in a clean environment. Dust, dirt, moisture, vibration, air currents and a close distance to other electronic equipment can all cause an adverse effect on the reliability and accuracy of your scale. Handle with care. Gently apply all items to be weighed onto tray top. Although this scale is designed to be quite durable, try to avoid rough treatment as this may permanently damage the internal sensor. Avoid shaking, dropping or otherwise shocking the scale. This is a precision instrument and must be handled with extreme care.
Only operate the scale on a stable, vibration free surface.
Page 3
I. OPERATION
Place Scale on a horizontal at surface.
1. Press [ ON ] key.
2. Wait until "0.0" or "0.00” is displayed. "S" should appear in the top left corner to indicate the scale is stable.
3. Put the object(s) on the weighing platform.
4. Using the [ MODE ] key, you can switch between
weighing units.
II. TARE WEIGHING
1. Turn on scale as described above.
2. Place the "tare item" on the platform.
3. Press [ TARE ] and wait until "0.0" or "0.00" is
displayed.
4. Add the "net-weight-item".
III. CALIBRATION
Calibration is NOT required before rst use. Only
calibrate if scale is not weighing properly. Make sure you are using the correct weight (not included) for your scale. All models may calibrate with a 100g weight*, but the default and recommended weight values are as follows:
SM-200 : 200g Calibration Weight SM-500 : 500g Calibration Weight SM-501 : 500g Calibration Weight
SM-DR : 500g Calibration Weight
1. Hold the ON key until the display shows "8888" then release.
Page 4
2. The display will then show "0.0", Hold the ON key again for 3 seconds until it displays "0", then release.
3. The LCD will now display the required calibration
weight for your scale* and "g" will be ashing.
4. Place your required calibration weight on the
platform. After 5 seconds, g will stop ashing.
Calibration is complete.
(*note: when the LCD displays the required calibration weight value, you can press TARE to change the value to "100g" if desired.The default calibration weight is the optimal weight to use, however - see list above)
IV. TROUBLESHOOTING
The primary reasons for inaccuracy or malfunction are low batteries, incorrect calibration, overload or operating on an unstable surface. Please keep this in mind and maintain and operate your scale properly. This scale is a precise instrument and must be handled with the utmost care and caution.
[Display] Elimination of errors
[Err3] You are overloading the scale. Remove the
excessive load immediately!
[ ] Readjust or replace batteries. [88888] Use the scale in a more stable position
Page 5
Model SM-200 SM-500 SM-501 SM-DR
Capacity 200g
7.05oz
128.6dwt
6.43ozt
1000ct
3086gn
500g
17.64oz
321.5dwt
16.08ozt
2500ct
7716gn
500g
17.64oz
321.5dwt
16.08ozt
2500ct
7716gn
100g
3.528oz
64.30dwt
3.215ozt
500ct
1543gn
500g
17.64oz
321.5dwt
16.08ozt
2500ct
7716gn
Resolution 0.01g
0.001oz
0.01dwt
0.001ozt
0.05ct
0.1gn
0.1g
0.01oz
0.1dwt
0.01ozt
0.5ct
1gn
0.01g
0.001oz
0.01dwt
0.001ozt
0.05ct
0.1gn
0.01g
0.001oz
0.01dwt
0.001ozt
0.05ct
0.1gn
0.1g
0.01oz
0.1dwt
0.01ozt
0.5ct
1gn
Default Calibration
Weight (not Included)
200g 500g 500g 500g
Platform Dimensions
(inches)
2.8 x 2.5 “
Scale Dimensions
(inches)
4.4 x 2.9 x 0.8”
Power 2 x AAA (included)
Specications
Loading...