Page 1
American Weigh Scales, Inc.
CV-10
CV-100
CV-300
User Manual
CV-Series
D i g i t a l P o c k e t S c a l e
CV-Series
I/O
M
T
Page 2
American Weigh CV-Series
Thank you for purchasing the American Weigh
CV-Series digital scale. Please read all operating
instructions carefully before use. This electronic scale
is a precision instrument. With normal care and proper
treatment, it will provide years of reliable service.
Never load the scale with more than the maximum
capacity. Overloading will permanently damage it!
Avoid any exposure to extreme heat or cold. Your
scale works better when operated at normal room
temperature. Always allow the scale to acclimatize to
normal room temperature for at least one hour before
use.
Give your scale sufcient warm up time. Usually
30-60 seconds before calibration to give the internal
components a chance to stabilize.
Keep your scale in a clean environment. Dust, dirt,
moisture, vibration, air currents and a close distance to
other electronic equipment can all cause an adverse
effect on the reliability and accuracy of your scale.
Handle with care. Gently apply all items to be weighed
onto tray top. Although this scale is designed to be
quite durable, try to avoid rough treatment as this may
permanently damage the internal sensor.
Avoid shaking, dropping or otherwise shocking the
scale. This is a precision instrument and must be
handled with extreme care.
Only operate the scale on a stable, vibration free
surface.
Page 3
I. OPERATION
Place Scale on a horizontal at surface.
1. Press [I/O] key.
2. Wait until the scale goes to zero.
3. Put the object(s) on the weighing platform.
4. Using the [M] key, you can switch between the
weighing units.
II. TARE WEIGHING
1. Turn on scale as described above.
2. Place the "tare item" on the platform. (ie tray)
3. Press [T] and wait until zero is displayed.
4. Add the "net-weight-item".
III. CALIBRATION
Calibration is NOT required before rst use. Only
calibrate if scale is not weighing properly.
**Make sure you use the correct calibration weight for
your scale or the calibration will not be accurate**
CV-10: 10g calibration weight
CV-100: 100g calibration weight
CV-300: 300g calibration weight
1. Turn OFF the scale.
2. Press and hold the [M] key, then tap the
[T]. The display will show "CAL".
3. Now release both keys. The internal serial number
will display. Press [T] again to zero the scale.
4. Place the required standard calibration weight (not
Page 4
included with CV-300/CV-100) onto the platform.
5. Press the [T] button again. The display will show the
calibration value.
6. Press [T] once more. The display will show "PASS"
and automatically turn off. Calibration is complete.
IV. TROUBLESHOOTING
The primary reasons for inaccuracy or malfunction
are low batteries, incorrect calibration, overload or
operating on an unstable surface. Please keep this in
mind and maintain and operate your scale properly.
This scale is a precise instrument and must be
handled with the utmost care and caution.
[Display] Elimination of errors
[OUE2] Recalibrate the scale as shown above.
[oL_d] You are overloading the scale. Remove the
excessive load immediately!
[nothing] Readjust or replace batteries.
[8888] Use the scale in a more stable position
Page 5
Specications
Model CV-10 CV-100 CV-300
Capacity 10g / 6.43dwt / 0.353oz /
0.322ozt / 50ct / 154.4gn
100g / 64.3dwt / 3.53oz /
3.22ozt / 500ct / 1544gn
300g / 193dwt / 10.59oz /
9.65ozt / 1500ct / 4630gn
Resolution 0.001g / 0.001dwt/ 0.001oz /
0.001ozt / 0.005ct / 0.02gn
0.01g / 0.01dwt / 0.001oz /
0.001ozt / 0.05ct / 0.1gn
0.1g / 0.1dwt / 0.01oz /
0.01ozt / 0.5ct / 1gn
Display 5-Digit Backlit LCD Display
Calibration Weight 10 g 100 g (sold seperate) 300 g (sold seperate)
Platform Dimensions
(inches)
2.6 x 2.1” (unfolded)
Scale Dimensions
(inches)
5.0 x 1.5 x 1.0” (closed)
Power 3 (three) LR-44 “calculator” Batteries (included)
Product Weight 2 oz
Loading...