American Weigh Scales, Inc.
CP3-100 (100x0.01g)
CP3-500 (500x0.1g)
User Manual
CP3-Series
Digital Pocket Scale
M
T
Zero
g
CP3-Series Manual
Thank you for purchasing the American Weigh
CP3-Series digital scale. Please read all operating
instructions carefully before use. This electronic scale
is a precision instrument. With normal care and proper
treatment, it will provide years of reliable service.
Never load the scale with more than the maximum
capacity. Overloading will permanently damage it!
Avoid any exposure to extreme heat or cold. Your
scale works better when operated at normal room
temperature. Always allow the scale to acclimate to
normal room temperature for at least one hour before
use.
Give your scale sufcient warm up time. Usually
30-60 seconds before calibration to give the internal
components a chance to stabilize.
Keep your scale in a clean environment. Dust, dirt,
moisture, vibration, air currents and a close distance to
other electronic equipment can all cause an adverse
effect on the reliability and accuracy of your scale.
Handle with care. Gently apply all items to be weighed
onto tray top. Although this scale is designed to be
quite durable, try to avoid rough treatment as this may
permanently damage the internal sensor.
Avoid shaking, dropping or otherwise shocking the
scale. This is a precision instrument and must be
handled with extreme care.
Only operate the scale on a stable, vibration free
surface.
I. OPERATION
Place Scale on a horizontal at surface.
1. Press [
] key.
2. Wait until "0.0” or "0.00" is displayed.
3. Place the object(s) on the weighing platform.
4. By pressing the [ M ] key, you can switch between
weighing units.
5. The removable lid can also be used as a weighing
tray.
II. TARE WEIGHING
1. Turn on scale as described above.
2. Place a tray or container on the scale platform.
3. Press [ T ] and wait until "0.0" or "0.00" is displayed.
4. You can now add items to the container or tray to
obtain just the weight of the contents.
III. CALIBRATION
Calibration is NOT required before rst use. Only
calibrate if scale is not weighing properly.
**The CP3-500 calibrates with a 500g weight (not
included). The CP3-100 calibrates with a 100g weight
(not included)**
1. Turn the scale ON.
2. Hold the [ M ] key for a few seconds. The display
will show "CAL", followed by the required calibration
weight (see above).
3. Place the calibration weight onto the platform and
press [
].
4. The display will show "PASS" then return to normal
weighin mode. Calibration is complete!
V. TROUBLESHOOTING
The primary reasons for inaccuracy or malfunction
are low batteries, incorrect calibration, overload or
operating on an unstable surface. Please keep this in
mind and maintain and operate your scale properly.
This scale is a precise instrument and must be
handled with the utmost care and caution.
[Display] Elimination of errors
-----------------------------------------------
[OUT2] Recalibrate the scale (Section III).
[EEEE] You are overloading the scale. Remove the
excessive load immediately!
[un2T] Use the scale in a more stable position
Model CP3-500 CP3-100
Capacity 500.0g
17.64oz
16.08ozt
321.5dwt
100.00g
3.527oz
500ct
1543.2gn
Resolution 0.1g
0.01oz
0.01ozt
0.1dwt
0.01g
0.001oz
0.05ct
0.1gn
Weighing Units
g, oz, ozt, dwt g, oz, ct, gn
Calibration Weight (not Included)
500g 100g
Platform Dimensions (inches)
2.0 x 2.7 “ Stainless Steel
Scale Dimensions (inches)
4.5 x 2.4 x 0.5”
Power
2 x CR2032 Batteries (included)
Warranty
10 Year Warranty
Specications
Loading...