User Manual
PCM-9361
Half EBX SBC with Intel® Atom
N270/VGA, LVDS, TTL, Giga
LAN, USB, SATA, SSD
PCM-9361 User Manual ii
Copyright
The documentation and the software included with this product are copyrighted 2009
by the manufacturer. All rights are reserved. The manufactuer reserves the right
to make improvements in the products described in this manual at any time without
notice.
No part of this manual may be reproduced, copied, translated or transmitted in any
form or by any means without the prior written permission of the manufactuer.
Information provided in this manual is intended to be accurate and reliable. However,
The manufactuer assumes no responsibility for its use, nor for any infringements
of the rights of third parties, which may result from its use.
Acknowledgements
Award is a trademark of Award Software International, Inc.
IBM, PC/AT, PS/2 and VGA are trademarks of International Business Machines Cor-
poration.
Intel and Atom are trademarks of Intel Corporation.
Microsoft Windows® is a registered trademark of Microsoft Corp.
RTL is a trademark of Realtek Semi-Conductor Co., Ltd.
ESS is a trademark of ESS Technology, Inc.
UMC is a trademark of United Microelectronics Corporation.
SMI is a trademark of Silicon Motion, Inc.
Creative is a trademark of Creative Technology LTD.
CHRONTEL is a trademark of Chrontel Inc.
All other product names or trademarks are properties of their respective owners.
Part No. 2006936110 Edition 1
Printed in China March 2009
iii PCM-9361 User Manual
Product Warranty (2 years)
The manufactuer warrants to you, the original purchaser, that each of its product
will be free from defects in materials and workmanship for two years from the date
of purchase.
This warranty does not apply to any products which have been repaired or altered by
persons other than repair personnel that have been authorized, or which have been
subject to misuse, abuse, accident or improper installation. We assume no
liability under the terms of this warranty as a consequence of such events.
Because of our high quality-control standards and rigorous testing, most of
our customers never need to use our repair service. If an the product is defective
it will be repaired or replaced at no charge during the warranty period. For outof-warranty repairs, you will be billed according to the cost of replacement materials,
service time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example, CPU
speed, products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages you get when the problem
occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return merchandize
authorization) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a fully-completed Repair and Replacement
Order Card and a photocopy proof of purchase date (such as your sales receipt)
in a shippable container. A product returned without proof of the purchase date
is not eligible for warranty service.
5. Write the RMA number visibly on the outside of the package and ship it prepaid
to your dealer.
Technical Support and Assistance
1. Visit the web site where you can find the latest information about the product.
2. Contact your distributor, sales representative, or customer service
center for technical support if you need additional assistance. Please have the
following information ready before you call:
– Product name and serial number
– Description of your peripheral attachments
– Description of your software (operating system, version, application sof tware,
etc.)
– A complete description of the problem
– The exact wording of any error messages
PCM-9361 User Manual iv
Packing List
Before installation, please ensure the following items have been shipped:
Item Part Number
1 PCM-9361 SBC
1 Startup manual (optional, upon request)
1 Utility CD (optional, upon request)
1 mini jumper pack
Cables:
Ordering information
Model Number Description
PCM-9361FG-S6A1E Atom N270 SBC,Giga-LAN,LCD,SATA,PCI-104
Optional accessories
Model Number Description
1700001531 FLAT CABLE 34P-2.54 mm/26P-2. 0mm 30 cm(LPT to FDD)
Part Number Description
1700006291 SATA cable 30cm
1700060202 CABLE 6P-6P-6P PS/2 KB & MOUSE 20cm
1700000265 WIRE ATX-20P(M)/12P(F) 10CM
1703100152 Audio Cable 10P 2.0mm 15cm
1701140201 FLAT 14PIN 2.0mm Secondary Port 9PIN(M)20cm
1703100121 Wire 10P 12cm IDC 2.0mm For USB 2 PORT
1700260250 Cable 25cm 25P to 26P ASS'Y LPT Port 2.0mm
v PCM-9361 User Manual
Contents
Chapter 1 General Introduction ...........................1
1.1 Introduction ...............................................................................................2
1.2 Product Features....................................................................................... 2
1.3 Specifications............................................................................................3
1.3.1 Functional Specification................................................................3
1.3.2 Mechanical Specification .............................................................. 5
1.3.3 Electrical Specification.................................... .... ... ... ....................6
1.3.4 Environmental Specification............ .... ... ... ... ................................. 6
Chapter 2 H/W installation....................................9
2.1 Jumpers ..................................................................................................10
2.1.1 Jumper list...................................................................................10
Table 2.1: Jumper list.... ... .... ... ... ... .... ........................................ 10
2.1.2 Jumper Settings.......................................................................... 10
Table 2.2: J1: Audio Power.................................. ... ... .... ... ... ... .. 10
Table 2.3: J2: AT/ATX Power Setting........................................10
Table 2.4: J3: PCI VIO Setting.......................... ... ... ..................11
Table 2.5: J4: Clear CMOS..................... ... ... .... ... ... ... ...............11
Table 2.6: J5: LCD Power......................................................... 11
Table 2.7: J6: COM2 Setting............................................. ... ... .. 12
2.2 Connectors.............................................................................................. 12
2.2.1 Connector list.............................................................................. 12
Table 2.8: Connector List.......................................................... 12
2.2.2 Connector Settings ..................................................................... 13
2.3 Mechanical..............................................................................................15
2.3.1 Jumper and Connector Locations............................................... 15
Figure 2.1 Jumper and Connector layout (Component side)..... 15
Figure 2.2 Jumper and Connector layout (Solder side)............. 16
2.3.2 Board Dimensions.......................................................................16
Figure 2.3 Board Dimension layout (Component side).............. 16
Figure 2.4 Board Dimension layout (Solder side)......................17
Figure 2.5 Board Dimension layout (Coastline)......................... 17
Chapter 3 BIOS settings.....................................19
3.1 BIOS Introduction....................................................................................20
3.2 BIOS Setup .............................................................................................20
3.2.1 Main Menu..................................................................................21
3.2.2 Standard CMOS Features ..........................................................22
3.2.3 Advanced BIOS Features............... .... ... ... ... ... .... ........................ 23
3.2.4 Advanced Chipset Features...................... ... ... .... ... ... ... ...............25
3.2.5 Integrated Peripherals................................................................. 26
3.2.6 Power Management Setup .........................................................28
3.2.7 PnP/PCI Configurations..............................................................30
3.2.8 PC Health Status ........................................................................ 31
3.2.9 Frequency/Voltage Control......................................................... 32
3.2.10 Load Optimized Defaults............................................................. 33
3.2.11 Set Password.............................................................................. 33
3.2.12 Save & Exit Setup.......................................................................35
3.2.13 Quit Without Saving .................................................. ... .... ... ... .....35
PCM-9361 User Manual vi
Chapter 4 Extension I/O Installation.................37
4.1 PCI-104................................................................................................... 38
Appendix A PIN Assignments ..............................39
A.1 PIN Assignments .................................................................................... 40
Table A.1: CN1: Audio............................................................... 40
Table A.2: CN2: Internal USB.................................................... 40
Table A.3: CN3: Internal USB.................................................... 41
Table A.4: CN4: SATA............................................................... 41
Table A.5: CN5: SATA............................................................... 42
Table A.6: CN6: Power Switch (Low Active )............................ 42
Table A.7: CN7: PCI-104 -12 V Input ........................................ 42
Table A.8: CN8: AT/ATX Power Input ....................................... 43
Table A.9: CN9: PCI-104........................................................... 43
Table A.10:CN10: 36 bits LVDS Panel....................................... 47
Table A.11:CN11: LPT................................................................ 48
Table A.12:CN12: GPIO............................................................. 49
Table A.13:CN13: 18 bits TTL Panel.......................................... 49
Table A.14:CN14: Inverter Power Output................................... 51
Table A.15:CN15: HDD & PWR LED.......................................... 51
Table A.16:CN16: SMBus........................................................... 52
Table A.17:CN17: COM2............................................................ 52
Table A.18:CN18: LAN............................................................... 53
Table A.19:CN19: CPU FAN (+5V) ............................................ 53
Table A.20:CN20: External USB................................................. 54
Table A.21:CN21: PS2 ............................................................... 54
Table A.22:CN22: COM1............................................................ 55
Table A.23:CN23: VGA............................................................... 55
Table A.24:CN24: CF ................................................................. 56
Table A.25:CN25: DDR2 SO-DIMM H=6.5mm........................... 58
Table A.26:CN26: Reset Button ................................................. 63
Chapter 1
1 General Introduction
This chapter gives background
information on the PCM-9361.
Sections include:
Introduction
Product Feature
Specifications
PCM-9361 User Manual 2
1.1 Introduction
The PCM-9361 is a 3.5" SBC (Single Board Computer) with Embedded Intel® Atom
N270 1.6 GHz Processor. PCM-9361 can support DDR2 memory up to 2GB, has five
USB 2.0 compatible ports, Giga LAN (1000 Mbps) interface, LVDS/TTL interface, HD
(High Definition) Audio, and one PCI-104 expansion connector. The PCM-9361 also
supports two SATA and two COM ports.
1.2 Product Features
General
CPU: Intel® Atom Processor N270 1.6 GHz
System Chipset Intel® 945GSE +ICH7M
BIOS: AWARD® 4 Mbit Flash BIOS
System Memory: DDRII 400/533 MHz SDRAM up to 2GB
SSD: Supports CompactFlash® Card TYPE I/II
Watchdog Timer: Single chip Watchdog 255-level interval timer, setup by soft-
ware
Expansion Interface: Supports PCI-104 device
Battery: Lithium 3 V/210 mAH
I/O
I/O Interface: 2 x SA TA(Supports 150MB/s), 1 x K/B, 1 x KB/mouse, 1 x RS232,
1 x RS232/422/485, 1 x LPT, 1 x FDD (share with LPT)
USB: 5 x USB 2.0 compliant Ports
Audio: High Definition Audio (HD),Line-in, Line out, Mic-in
GPIO: 8-bit general purpose input/output
Ethernet
Chipset: Realtek 8110SC
Speed: 1000 Mbps
Interface: 1 x RJ45
Standard: Compliant with IEEE 802.3, IEEE 802.3u, IEEE 802.3x, IEEE
802.ab.
Display
Chipset: Intel® 945GSE
Memory Size: Up to 64 MB of dynamic video memory allocation
Resolution:
- CRT display Mode: Supports QXGA Up to 2048 x 1536
- TTL display Mode: Up to 800 x 600
TTL LCD: Supports 18-bit TTL LCD
LVDS LCD: Supports 36-bit LVDS LCD
Dual Display:
- CRT + LVDS (36-bits)
- CRT + TTL (18-bits)
3 PCM-9361 User Manual
Chapter 1 General Introduction
1.3 Specifications
1.3.1 Functional Specification
Processor
Intel® Atom™ Processor N270
Intel® Atom TM N270 at 1.6 GHz with 512 KB L2 cache
437-pin FCBGA8 package
FSB: 533 MHz
Bus Ratio: 12
Manufacturing Technology: 45nm
Thermal Design Power: 2.5 W
Thermal Specificat ion: 90°C
VID Voltage Range: 90 V-1.100 V
Chipset (945GSE)
Memory
945GSE GMCH
Supports 2 GB maximum memory
One 64-bit wide DDR2 SDRAM single channel
Supports DDR2 400, DDR2 533, 256 Mb, 512 Mb 1 Gb and
2Gb DDR2 technology
Only x8, x16 DDR2 devices with 4 or 8 banks
Support for DDR2 On-Die Termination(ODT)
Socket:
SODIMM Socket:
1. 200-pin SODIMM socket type *1
Graphic and Video
Controllers
945GSE
Intel 3.5 Gen Integrated Graphic Engine
DVMT 3.0 (Dynamic Video Memory Technology)
Display Dynamic Power Saving Technology 2.0 (Intel DPST
2.0) Intel Smart 2D Display Technology (S2DDT)
PCM-9361 User Manual 4
Chipset (ICH7M)
IDE Interface
ICH7M support
Single, independent IDE signal channel
Supports one CF device
H.D. Codec ALC888
I/F
ICH7M support
Support for HD codec
Supports up to 2.1 channel of PCM audio output
Connectors:Line-out, Line-in, Mic-in: Pin header 2*5P (M)
2.0 mm
Concurrent PCI/PCIe
Bus Controller
MIO 2.0 ICH7M chip support
PCI 2.1 compliant
32-bit 3.3 V 33 MHz PCI interface with 5 V tolerant inputs
Supports PC/PCI DMA
PCI Express 1.0a compliant
SATA Connector
ICH7M support
Supports independent DMA operation on two ports
Supports data transfer rates of up to 1.5 Gb/s (150 MB/s)
Operation of AHCI using memory space
Supports several optional sections of the Serial ATA II
SATA connectors:
Connector: Serial ATA II 7 pins 1.27 mm x 2
USB Interface
ICH7M support
Supports 5 USB 2.0 ports which are high-speed, fullspeed, and low-speed capable
Port-routing logic determines whether a USB port is controlled by UHCI or EHCI
USB Connector:(USB1~4) 2 set 5 x 2-pin Hirose DF13
type
Power Management
ICH7M support
Fully supports ACPI (Advanced Configuration and
Power Interface) 2.0
Supports S1, S5
PCI CLKRUN# and PME# support
SMI# (System Management Interrupt) generation
BIOS
ICH7M support
Phoenix 4M bit Flash BIOS, supports Plug & Play, APM
1.2/ ACPI 1.1.
FWH Type
Socket: 32-pin PLCC socket
5 PCM-9361 User Manual
Chapter 1 General Introduction
Other chipset
1.3.2 Mechanical S pecification
1.3.2.1 Dimension (mm)
L146.00 mm * W102 mm
1.3.2.2 Height on Top (mm)
18.80 mm
1.3.2.3 Height on Bottom (mm)
6.65 mm (CF Socket)
Graphic and Video
Controllers
945GSE Intel 3.5 Gen Integrated Graphic Engine
CRT: Supports QXGA Up to 2048 x 1536,
TTL: Up to 640 x 480, 800 x 600
LVDS: Support 2 channel 36-bit LVDS panel,
LVDS connector : Hirose DF13 type 40 pin
TTL connector : Hirose DF13 type 40 pin
CRT connector : D-SUB15 at coastline
LAN
Realtek 8110SC.
Compliant with IEEE 802.3, IEEE 802.3u, IEEE
802.3x, IEEE 802.ab.
Support 1000Mbps.
Connectors:
Phone Jack RJ45 8P 90D(F)
Serial ports
SMSC3114 (LPC Super I/O) supports:
2 full function serial ports. High Speed NS16C550A
Compatible UARTs with Data rates to 1.5Mbps
Support IRQ Sharing among serial ports.
RS-485 Auto Direction Control Mode
Connectors:COM1(RS-232), DB-9 COM2(RS-232/
422/485 with auto-flow control), 14-pin 2.0 mm 2 x 7
Box Header
Parallel port
SMSC SCH 3114 supports (LPC Super I/O).
LPT interface connector: 26-pin flat-cable connector
Keyboard/Mouse
connectors
SMSC SCH 3114 supports (LPC Super I/O).
PS/2 Keyboard and Mouse interface.
Connector: Mini-Din 6P at coastline
GPIO
Intel ICH7M supports.
8-Bit GPIO.
5 V tolerance I/Os.
Connectors:
10 pins 2.0mm pin header.
Battery backup 2 pin wafer box for external Battery on board
PCM-9361 User Manual 6
1.3.2.4 Weight (g) with Heatsink
0.85 g
1.3.3 Electrical Specification
1.3.3.1 Power Supply Voltage
Voltage requirement with AT/ATX Power:
AT:
+5 V
DC
±5%
ATX:
+12 V
DC
±5%
+5 V
DC
±5%,
+5 V Standby for ATX mode
1.3.3.2 Power Supply Current
Supply Current (ATX)
CPU : Intel Atom N270 1.6 GHz
1.3.3.3 RTC Battery
Typical Voltage : 3.0 V
Nomal discharge capacity : 210 mAh
1.3.4 Environmental Specification
1.3.4.1 Operating Temperature
Operating temperature: 0 ~ 60°C (32~140°F)
* Tested under 60°C chamber temperature with 0.23 m/s air flow.
1.3.4.2 Operating Humidity
Operating Humidity:10% ~ 90% Relative Humidity, non-condensing
1.3.4.3 Storage Temperature
Standard products (0 ~ 60°C)
Storage temperature: -20~70°C
1.3.4.4 Storage Humidity
Standard products (0 ~ 60°C)
Relative Humidity: 95% @ 60°C
XP Mode ATX
5 V 12 V
Typical 1.90 A 0.07 A
Suspend 1.36 A 0.06 A
Max Load 2.38 A 0.09 A
7 PCM-9361 User Manual
Chapter 1 General Introduction
PCM-9361 User Manual 8
Chapter 2
2 H/W installation
This chapter explains the setup
procedures of the PCM-9361 hardware, including instructions on
setting jumpers and connecting
peripherals, switches, indicators
and mechanical drawings. Be sure
to read all safety precautions
before you begin the installation
procedure.
PCM-9361 User Manual 10
2.1 Jumpers
2.1.1 Jumper list
2.1.2 Jumper Settings
Table 2.1: Jumper list
J1 Audio Power
J2 AT/ATX Power Setting
J3 PCI VIO Setting
J4 Clear CMOS
J5 LCD Power
J6 COM2 Setting
Table 2.2: J1: Audio Power
Part Number 1653003101
Footprint JH3X1V-2M
Description PIN HEADER 3*1P 180D(M) 2.0mm DIP SQUARE W/O Pb
Setting Function
(1-2) +12 V to +5 V LDO
(2-3) +5 V
Table 2.3: J2: AT/ATX Power Setting
Part Number 1653002101
Footprint JH2X1V-2M
Description PIN HEADER 2*1P 180D(M)SQUARE 2.0mm DIP W/O Pb
Setting Function
NC ATX Power
(1-2) AT Power
11 PCM-9361 User Manual
Chapter 2 H/W installation
Table 2.4: J3: PCI VIO Setting
Part Number 1653003101
Footprint JH3X1V-2M
Description PIN HEADER 3*1P 180D(M) 2.0mm DIP SQUARE W/O Pb
Setting Function
(1-2) +5 V
(2-3) +3.3 V
Table 2.5: J4: Clear CMOS
Part Number 1653003101
Footprint JH3X1V-2M
Description PIN HEADER 3*1P 180D(M) 2.0mm DIP SQUARE W/O Pb
Setting Function
(1-2) Normal
(2-3) Clear COMS
Table 2.6: J5: LCD Power
Part Number 1653003101
Footprint JH3X1V-2M
Description PIN HEADER 3*1P 180D(M) 2.0mm DIP SQUARE W/O Pb
Setting Function
(1-2) +5 V
(2-3) +3.3 V
PCM-9361 User Manual 12
2.2 Connectors
2.2.1 Connector list
Table 2.7: J6: COM2 Setting
Part Number 1653003260
Footprint HD_3x2P_79
Description PIN HEADER 3*2P 180D(M) 2.0mm SMD SOUARE PIN
Setting Function
(1-2) RS232
(3-4) RS485
(5-6) RS422
Table 2.8: Connector List
CN1 Audio
CN2 Internal USB
CN3 Internal USB
CN4 SATA
CN5 SATA
CN6 Power Switch (Low Active )
CN7 PCI-104 -12V Input
CN8 AT/ATX Power Input
CN9 PCI-104
CN10 36 bits LVDS Pa nel
CN11 LPT
CN12 GPIO
CN13 18 bits TTL Panel
CN14 Inverter Power Output
CN15 HDD & PWR LED
CN16 SMBus
CN17 COM2
CN18 LAN
CN19 CPU FAN (+5V)
CN20 External USB
CN21 PS2
CN22 COM1
CN23 VGA
CN24 CF
CN25 DDR2 SO-DIMM H=6.5mm
CN26 Reset Button
13 PCM-9361 User Manual
Chapter 2 H/W installation
2.2.2 Connector Settings
2.2.2.1 Audio Interface (CN1)
Audio Port Connectors
One 5 x 2 pin box header for Audio connector. These audio connectors are used for
audio devices. The audio jacks are differentiated by color for different audio sound
effects.
2.2.2.2 USB Connectors (CN2, CN3, CN20)
The board provides up to Five USB (Universal Serial Bus) ports. This gives complete
Plug and Play, and hot attach/detach for up to 127 external devices. The USB interface comply with USB specification Rev. 2.0 which supports 480 Mbps transfer rate,
and are fuse protected.
There are 5 x 2 pin 180D (M) connectors for internal use, 4 x USB ports CN2, CN3
and one external USB port CN20. You will need an adapter cable if you use a standard USB connector. On one end the adapter cable has a 5 x 2-pin connector with a
foolproof connection to prevent it from being plugged in the wrong way and on the
other end a USB connector.
* CN3 conflicts with PC/104 connector of PC/104+ module, please plug PCI-104
module only or remove PC/104 connector of PC/104+ module.
2.2.2.3 SATA Connector (CN4, CN5)
PCM-9361 supports Serial ATA via two connectors (CN4, CN5). Data transfer rates
up to 150 MB/s are possible, enabling very fast data and file transfer, and independent DMA operation on two ports.
2.2.2.4 Power Switch Connector (CN6)
One 2 x 1 pin wafer box (CN6) for power switch.
2.2.2.5 Power Connectors (CN8)
Main power connector, +5 V, +12 V or 5 V only
PCM-9361 supports ATX and AT modes
Use ATX power cable (PN: 1700000265 ATX-20P (M)/12P (F) 10 CM) connect CN8,
it's changed from 12pin to 20pin, provides 5 V and 12 V and other PS_ON signals.
2.2.2.6 LVDS LCD Panel Connector (CN10)
The board supports 2 channel 18-bit LVDS LCD panel display. Users can connect to
a 36-bit LVDS LCD.
2.2.2.7 GPIO (General Purpose Input Output) (CN12)
The board supports 8-bit GPIO through GPIO connector . The 8 digit al in and out-put s
can be programmed to read or control devices, with input or output defined. The
default setting is 4 bits input and 4 bits output.
2.2.2.8 TTL LCD Panel Connector (CN13)
The board supports 18-bit TTL LCD panel displays.
2.2.2.9 Power & HDD LED Indicator (CN15)
The HDD LED indicator for hard disk access is an active low signal (24 mA sink rate).
Power supply activity LED indicator.
2.2.2.10 SMBus Connector (CN16)
One 4 x 1 pin wafer box (CN16) supports SMBus interface.
PCM-9361 User Manual 14
2.2.2.11 COM Port Connector (CN17, CN22)
The PCM-9361 provides 2 serial ports (COM1 and COM2).
One 7*2P PIN HEADER (CN17) for COM2 output; and one DB-9 connector for
COM1(CN22)
COM RS-232/422/485 setting (J6)
COM2 can be configured to operate in RS-232, RS-422, or RS-485 mode.
This is done via J6.
It provides connections for serial devices (ex: a mouse, etc.) or a co mmunicatio n network. You can find the pin assignments for the COM port connector in Appendix A.
2.2.2.12 Ethernet configuration(CN18)
10/100/1000 Mbps connections are made via RJ-45 connectors.
The board is equipped with 1 high performance PCI Ethernet interface which is fully
compliant with IEEE 802.3u 100Base-T & IEEE 802.3ab 1000Base-T. It is supported
by all major network operating systems.
2.2.2.13 Fan Power Supply Connector (CN19)
Provides +5 V power supply to CPU cooling fan.
2.2.2.14 Keyboard and PS/2 mouse connector (CN21)
The board provides a keyboard connector that supports both a keyboard and a PS/2
style mouse. In most cases, especially in embedded applications, a keyboard is not
used. If the keyboard is not present, the standard PC/AT BIOS will report an error or
fail during power-on self-test (POST) after a reset. The product's BIOS standard
setup menu allows you to select "All, But Keyboard" under the "Halt On" selection.
This allows no-keyboard operation in embedded system applications, without the
system halting under POST.
2.2.2.15 CRT display connector (CN23)
The CRT display connector is a DB15 connector used for conventional CRT displays.
2.2.2.16 CompactFlash (CN24)
The CompactFlash card shares a Primary IDE channel which can be enabled/disabled via the BIOS settings.
2.2.2.17 DDRII DIMM Socket (CN25)
One 200-pin/H6.5 mm DDRII DIMM socket (CN25) supports DDRII 400/533 MHz up
to 2 GB.
2.2.2.18 Power Reset button (CN26)
Momentarily pressing the reset button will activate a reset. The switch should be
rated for 10 mA, 5 V.
J6 COM2 Setting
Setting Function
(1-2) RS232
(3-4) RS485
(5-6) RS422
15 PCM-9361 User Manual
Chapter 2 H/W installation
2.3 Mechanical
2.3.1 Jumper and Connector Locations
Figure 2.1 Jumper and Connector layout (Component side)
PCM-9361 User Manual 16
Figure 2.2 Jumper and Connector layout (Solder side)
2.3.2 Board Dimensions
Figure 2.3 Board Dimension layout (Component side)
17 PCM-9361 User Manual
Chapter 2 H/W installation
Figure 2.4 Board Dimension layout (Solder side)
Figure 2.5 Board Dimension layout (Coastline)
PCM-9361 User Manual 18
Chapter 3
3 BIOS settings
PCM-9361 User Manual 20
3.1 BIOS Introduction
AwardBIOS 6.0 is a full-featured BIOS provided to deliver superior performance
compatibility, and functionality to industrial PCs and embedded boards. Its
many options and extensions let you customize your products to a wide range of
designs and target markets.
The modular, adaptable AwardBIOS 6.0 supports the broadest range of third-party
peripherals and all popular chipsets, plus Intel, AMD, nVidia, VIA, and compatible
CPUs from 386 through Pentium, AMD Geode, K7 and K8 (including multiple processor platforms), and VIA Eden C3 and C7 CPUs.
You can use the utilities to select and install features that suit your needs
and your customers' needs.
3.2 BIOS Setup
The PCM-9361 system has AwardBIOS 6.0 built-in, which includes a CMOS SETUP
utility that allows users to configure settings as required or to activate certain system
features.
The CMOS SETUP saves configuration settings in the CMOS RAM of the motherboard. When the system power is turned off, the onboard battery supplies the necessary power to the CMOS RAM so that settings are retained.
To access the CMOS SETUP screen, press the <Del> button during the power-on
BIOS POST (Power-On Self Test).
CMOS SETUP Navigation and Control Keys:
< ↑ >< ↓ >< ← >< → >
Move to highlight item
<Enter> Select Item
<Esc>
Main Menu - Start Quit sequence
Sub Menu - Exit the current page and return to level above
<Page Up/+> Increase the numeric value or make changes
<Page Down/-> Decrease the numeric value or make changes
<F1> General help, for Setup Sub Menu
<F2> Item Help
<F5> Load Previous Values
<F7> Load Optimized Default
<F10> Save all CMOS changes
21 PCM-9361 User Manual
Chapter 3 BIOS settings
3.2.1 Main Menu
Press the <Del> key during startup to enter the BIOS CMOS Setup Utility; the Main
Menu will appear on the screen. Use arrow keys to highlight the desired item, and
press <Enter> to accept, or enter the sub-menu.
Standard CMOS Features
This setup page includes all the features for standard CMOS configuration.
Advanced BIOS Features
This setup page includes all the features for advanced BIOS configuration.
Advanced Chipset Features
This setup page includes all the features for advanced chipset configuration.
Integrated Peripherals
This setup page includes all onboard peripheral devices.
Power Management Setup
This setup page includes all the power management items.
PnP/PCI Configurations
This setup page includes PnP OS and PCI device configuration.
PC Health Status
This setup page includes the system auto-detect CPU and system temperature, voltage, and fan speed.
Frequency/Voltage Control
This setup page includes CPU host clock control, frequency ratio and voltage.
Load Optimized Defaults
This selection loads optimized values for best system performance configuration.
Set Password
Establish, change or disable passwords.
Save & Exit Setup
Save CMOS value settings to CMOS and exit BIOS setup.
Exit Without Saving
Abandon all CMOS value changes and exit BIOS setup.
PCM-9361 User Manual 22
3.2.2 Standard CMOS Features
Date
The date format is <weekday>, <month>, <day>, <year>.
Time
The times format in <hour> <minute> <second>, base on the 24-hour time.
IDE Channel 0/1 Master/Slave
IDE HDD Auto-Detection - Press "Enter" for automatic device detection.
Drive A
The Item identifies the types of floppy disk drive A or drive B
Halt on
This item determines whether the computer will stop if an error is detected during power up.
Weekday From Sun to Sat, determined and display by BIOS only
Month From Jan to Dec.
Day From 1 to 31
Year From 1999 through 2098
None No floppy drive installed
360K, 5.25" 5.25 inch PC-type standard drive; 360K byte capacity
1.2M, 5.25" 5.25 inch AT-type high-density drive; 1.2M byte capacity
720K, 3.5" 3.5 inch double-sided drive; 720K byte capacity
1.44M, 3.5" 3.5 inch double-sided drive; 1.44M byte capacity
2.88M, 3.5" 3.5 inch double-sided drive; 2.88M byte capacity
No Errors The system boot process will not stop for any error
All Errors Whenever the BIOS detects a non-fatal error the system boot pro-
cess will be stopped.
All, But Keyboard The system boot process will not stop for a keyboard error, but will
stop for all other errors. (Default value)
23 PCM-9361 User Manual
Chapter 3 BIOS settings
Base Memory
Displays the amount of base (or conventional) memory installed in the system.
Extended Memory
Displays the amount of extended memory (above 1 MB in CPU's memory
address map) installed in the system.
Total Memory
Displays the total system memory size.
3.2.3 Advanced BIOS Features
CPU Feature
This item allows the user to adjust CPU settings such as CPU ratio, VID and
Thermal, and special features like XD flag.
Hard Disk Boot Priority
This item allows the user to select the boot sequence for system devices such
as HDD, SCSI, and RAID.
CPU L1 & L2 Cache [Enabled]
This item allows user to enable CPU L2 cache and ECC checking function.
CPU L3 Cache [Enabled]
This item allows the user to enable/disable CPU L3 cache.
Hyper-Threading Technology [Enabled]
This item allows the user to enable/disable Hyper-threading support for the
Intel® Pentium® 4 processor with HT Technology.
All, But Diskette The system boot process will not stop for a diskette error, but will
stop for all other errors.
All, But Disk/Key The system boot process will not stop for a keyboard or disk error,
but will stop for all other errors.
PCM-9361 User Manual 24
Quick Power On Self Test [Enabled]
This field speeds up the Power-On Self Test (POST) routine by skipping re-testing a second, third and fourth time. The default setting is enabled.
First / Second / Third / Other Boot Drive
Boot Up NumLock Status [On]
This item allows the user to activate the Number Lock key at system boot.
Gate A20 Option [Fast]
This item allows the user to switch on or off A20 control by port 92.
Typematic Rate Setting
This item allows the user to set the two typematic control items.
This field controls the speed of
– Typematic Rate (Chars/Sec)
This item controls the speed at which the system registers auto repeated keystrokes.
The eight settings are: 6, 8, 10, 12, 15, 20, 24 and 30.
– Typematic Delay (Msec)
This item sets the key press delay time before auto repeat begins. The four
delay rate options are: 250, 500, 750 and 1000.
Security Option [Setup]
APIC Mode [Enabled]
This item allows the user to enable/disable the "Advanced Programmable Interrupt Controller". APIC is implemented in the motherboard and must be supported by the operating system; it extends the number of IRQs available.
MPS Version Control for OS [1.4]
This item sets the operating system multiprocessor support version.
OS Select For DRAM > 64 MB [Non-OS2]
Select OS2 only if the system is running the OS/2 operating system with greater
than 64 MB of RAM on the system.
Hard Disk Sets boot priority for the hard disk.
CDROM Sets boot priority for CDROM.
USB-FDD Sets boot priority for USB-FDD.
USB-ZIP Sets boot priority for USB-ZIP.
USB-CDROM Sets boot priority for USB-CDROM.
LAN Sets boot priority for LAN.
Disabled Disables this boot function.
System System requires correct password before booting, and also b efore
permitting access to the Setup page.
Setup System will boot, but requires correct password before permitting
access to Setup. (Default value)
25 PCM-9361 User Manual
Chapter 3 BIOS settings
3.2.4 Advanced Chipset Features
DRAM Timing Selectable [By SPD]
This item enables users to set the optimal timings for items 2 through 5, system
default setting of "By SPD" to follow the SPD information and ensure the syste m
running in stable and optimal performance.
CAS Latency Time [Auto]
This item enables users to set the timing delay in clock cycles before SDRAM
start a read command after receiving it.
DRAM RAS# to CAS# Delay [Auto]
This item enables users to set the timing of the transition from RAS (row
address strobe) to CAS (column address strobe) as both rows and column are
separately addressed shortly after DRAM is refreshed.
DRAM RAS# Precharge [Auto]
This item enables users to set the DRAM RAS# precharge timing, system
default is setting to "Auto" to reference the data from SPD ROM.
Precharge delay (tRAS) [Auto]
This item allows user to adjust memory precharge time
System Memory Frequency [Auto]
This item allows user to adjust memory frequency to improvement performance.
SLP_S4# Assertion Width [4 to 5 Sec]
This item allow user to set the SLP_S4# Assertion Width.
System BIOS Cacheable [Enabled]
This item allows the system BIOS to be cached to allow faster execution and
better performance.
Note! The "Advanced Chipset Features" screen controls the configuration of
the board's chipset register settings and performance tuning - the
options on this screen may vary depending on the chipset type. It is
strongly recommended that only technical users make changes to the
default settings.
PCM-9361 User Manual 26
Video BIOS Cacheable [Disabled]
This item allows the video BIOS to be cached to allow faster execution and better performance.
Memory Hole At 15M-16M [Disabled]
This item reserves 15MB-16MB memory address space to ISA expansion cards
that specifically require the setting. Memory from 15MB-16MB will be unavailable to the system because of the expansion cards can only access memory at
this area.
PCI Express Root Port Func [Press Enter]
This item allows the user to adjust the PCIE port to on, off, or auto.
On-Chip Frame Buffer Size [8MB]
This item allows the user to adjust on-chip graphics of memory buffer.
DVMT Mode [DVMT]
This item allows the user to adjust Intel's Dynamic Video Memory Technology
(DVMT).Bios provide three option to choose (DVMT,FIXED and Both).
DVMT/FIXED Memory Size [128MB]
This item allows the user to adjust DVMT/FIXED graphics memory size.
Boot Display [CRT]
This item allows the user to decide which display mode to use for the boot display.
Panel Type [ 640 x 480, 18bits]
This item allows the user to adjust panel resolution.
3.2.5 Integrated Peripherals
Note! The "Integrated Peripherals" screen controls chipset configuration for
IDE, ATA, SATA, USB, AC97, MC97 and Super IO and Sensor devices.
The options on this screen vary depending on the chipset.
27 PCM-9361 User Manual
Chapter 3 BIOS settings
OnChip IDE Device
This item enables users to set the OnChip IDE device status, including IDE
devices and setting PIO and DMA access modes. Some chipsets support newer
SATA devices (Serial-ATA).
Onboard Device
This item enables users to set the Onboard device status, includes enable USB,
AC97, MC97 and LAN devices.
Super IO Device
This item enables users to set the Super IO device status, includes enable
Floppy, COM, LPT, IR and control GPIO and Power fail status.
USB Device Setting
This item enables users to set the USB device type.
Onboard Serial port 1 [ 3F8/IRQ4]
This item allows the user to adjust serial port 1 address.
Onboard Serial port 2 [ 2F8/IRQ3]
This item allows the user to adjust serial port 2 address.
SP 2 AutoFlow Control [ Disabled]
This item allows the user to enable serial port 2 autoflow control function.
Onboard Parallel Port [378/IRQ7]
This item allows the user to adjust parallel port address and IRQ.
Parallel Port Mode [Standard]
This item allows the user to adjust parallel port mode.
ECP Mode Use DMA [3]
This item allows the user to adjust the ECP DMA resource.
PCM-9361 User Manual 28
3.2.6 Power Management Setup
ACPI Function [Enabled]
This item defines the ACPI (Advanced Configuration and Power Management)
feature that makes hardware status information available to the operating system, and communicate PC and system devices for improving the power management.
ACPI Suspend Type [S3 (STR)]
This item allows user to select sleep state state when the computer is in suspend mode.
Run VGA BIOS if S3 Resume [Auto]
This item allows the user to enable run VGA bios if system resume from S3.
Power Management [Min Saving]
This item allows user to select system power saving mode.
Note! The "Power Management Setup" screen allows configuration of the sys-
tem for effective energy savings while still operating in a manner consistent with intended computer use.
S1 (POS) The suspend mode is equivalent to a software power down.
S3 (STR) The system shuts down with the exception of a refresh current to
the system memory.
Min Saving Minimum power management. Suspend Mode=1 hr.
Max Saving Maximum power management. Suspend Mode=1 min.
User Define Allows user to set each mode individually.
Suspend Mode= Disabled or 1 min ~1 hr.
29 PCM-9361 User Manual
Chapter 3 BIOS settings
Video Off Method [DPMS]
This item allows the user to determine the manner in which the monitor is
blanked.
Video Off In Suspend [Yes]
This item allows user to turn off video during system enter suspend mode.
Suspend Type [Stop Grant]
This item allows user to determine the suspend type.
Modem use IRQ [3]
This item allows user to determine the IRQ which the MODEM can use.
Suspend Mode [1 Hour]
This item allows user to determine the time of system inactivity, all devices
except the CPU will be shut off.
HDD Power Down Mode [15 Min]
This item allows user to determine the time of system inactivity, the hard disk
drive will be powered down.
Soft-Off by PWR-BTTN [Instant-Off]
This item allows the user to define the power button functions.
PWRON After PWR-Fail [Former-Sts]
This item allows the user to select recovery after power fail function; this function depends on the chipset.
Wake-Up by PCI card [Enabled]
This item allows user to defines PCI cards to wake up the system from the suspend mode.
Power On by Ring [Enabled]
This item allows user to define the system will resume by activating of modem
ring.
Resume by Alarm [Disabled]
This item allows user to enable and key in Date/time to power on system
V/H SYNC+Blank This option will cause the system to turn off vertical and horizontal
synchronization ports and write blanks to the video buffer.
Blank Screen This option only writes blanks to the video buffer.
DPMS Initial display power management signaling.
Instant-Off Press the powe r bu tton to power off instantly.
Delay 4 Sec Press and hold the power button for 4 sec to power off.
Disabled Disable this function.
Enabled Enable alarm function to power on system
Day (of month) Alarm 1-31
Time (HH:MM:SS) Alarm (0-23) : (0-59) : 0-59)
PCM-9361 User Manual 30
3.2.7 PnP/PCI Configurations
Init Display First [PCI Slot]
This item is setting for start up Video output from PCI or Onboard device.
Reset Configuration Data [Disabled]
This item allow user to clear any PnP configuration data stored in the BIOS.
Resources Controlled By [Auto (ESCD)]
– IRQ Resources
This item allows you respectively assign an interruptive type for IRQ-3, 4, 5,
7, 9, 10, 11, 12, 14, and 15.
– DMA Resources
This item allows you respectively assign an interruptive type for DMA, 0, 1, 2,
3, 4, 5, 6, and 7.
PCI VGA Palette Snoop [Disabled]
The item is designed to solve problems caused by some non-standard VGA
cards. A built-in VGA system does not need this function.
INT Pin 1~8 Assignment [Auto]
This item allows the user to select the interrupt request (IRQ) assigned to a
device connected to the PCI interface on your system.
Maximum Payload Size [4096]
This item allows the user to adjust maximum TLP (Transaction Layer Packet)
payload size.
Note! This "PnP/PCI Configurations" option sets up the IRQ and DMA (both
PnP and PCI bus assignments).
31 PCM-9361 User Manual
Chapter 3 BIOS settings
3.2.8 PC Health Status
Current CPU Temperature [Show Only]
This item displays current CPU temperature.
FAN 1 Speed [Show Only]
This item displays current system FAN(s) speed(s).
VCC/ 2.5 V/ 5V/ 12V [Show Only]
This item displays current CPU and system voltage.
Note! This "PC Health Status" page reports the thermal, fan and voltage status
of the board. This page may vary according to the chipset installed.
PCM-9361 User Manual 32
3.2.9 Frequency/Volta ge Cont rol
CPU CIock Ratio [6X]
This item enables users to set the CPU clock ratio by manually.
Auto Detect PCI Clk [Enabled]
This item enables users to set the PCI Clk either by automatic system detection
or manually.
Spread Spectrum [Disabled]
This item enables users to set the spread spectrum modulation.
CPU Host/SRC/PCI Clock [Defautl]
This item enables users to set the CPUhost/SRC/PCI clock.
Note! The "Frequency/Voltage Control" screen controls the CPU host and PCI
frequency. The options on this page vary depending on the chipset;
items show up according to installed CPU capacities.
33 PCM-9361 User Manual
Chapter 3 BIOS settings
3.2.10 Load Optimized Defaults
3.2.11 Set Password
Note! "Load Optimized Defaults" loads the default system values directly from
ROM. If the stored record created by the setup program should ever
become corrupted (and therefore unusable), select Load Setup Defaults
to have these default values load automatically for the next bootup.
Note! To enable this feature, you should first go to the "Advanced BIOS Fea-
tures" menu, choose the Security Option, and select either System or
Setup, depending on which aspects you want password protected. System requires a password both to boot the system and to enter Setup.
Setup requires a password only to enter Setup. A password may be at
most 8 characters long.
PCM-9361 User Manual 34
To Establish Password
1. Choose the Set Password option from the CMOS Setup Utility Main Menu and
press <Enter>.
2. When you see Enter Password, enter the desired password and press <Enter>.
3. At the Confirm Password prompt, retype the desired password, then press
<Enter>.
4. Select Save to CMOS and exit, type <Y>, then <Enter>.
To Change Password
1. Choose the Set Password option from the CMOS Setup Utility main menu and
press <Enter>.
2. When you see Enter Password, enter the existing password and press <Enter>.
3. You will see the Confirm Password prompt, type it in again, and press <Enter>.
4. Select Set Password again, and at the Enter Password prompt, enter the new
password and press <Enter>.
5. At the Confirm Password prompt, retype the new password, and press <Enter>.
6. Select Save to CMOS and exit, type <Y>, then <Enter>.
To Disable a Password
1. Choose the Set Password option from the CMOS Setup Utility main menu and
press <Enter>.
2. When you see the Enter Password prompt, enter the existing password and
press <Enter>.
3. You will see Confirm Password, type it in again, and press <Enter>.
4. Select Set Password again, and at the Enter Password prompt, DO NOT enter
anything - just press <Enter>.
5. At the Confirm Password prompt, again, DO NOT type in anything - just press
<Enter>.
6. Select Save to CMOS and exit, type <Y>, then <Enter>.
35 PCM-9361 User Manual
Chapter 3 BIOS settings
3.2.12 Save & Exit Setup
3.2.13 Quit Without Saving
Note! Typing "Y" will quit the BIOS Setup Utility and save user setup values to
CMOS.
Typing "N" will return to BIOS Setup Utility.
Note! Typing "Y" will quit the BIOS Setup Utility without saving any changes to
CMOS.
Typing "N" will return to the BIOS Setup Utility.
PCM-9361 User Manual 36
Chapter 4
4 Extension I/O
Installation
PCM-9361 User Manual 38
4.1 PCI-104
After applying force to the IPC connector
,
the footprint of the module / CPU board
needs to be inserted correctly.
After applying force to the conn ector, the
footprint of the module / CPU board
needs to be inserted correctl
y
.
Aim the pin connector to the footprint
and apply force evenly.
Appendix A
A PIN Assignments
PCM-9361 User Manual 40
A.1 PIN Assignments
Matching Cable : 1703100152
Matching Cable : 1703100121
Table A.1: CN1: Audio
Part Number 1653205260
Footprint BH5X2SV
Description BOX HEADER SMD 5*2 180D (M) 2.0mm
Pin Pin Name
1LOUTR
2LINR
3GND
4GND
5LOUTL
6LINL
7GND
8GND
9MIC1R
10 MIC1L
Table A.2: CN2: Internal USB
Part Number 1653005260
Footprint HD_5x2P_79_N10
Description PIN HEADER 2*5P 180D(M) 2.0mm SMD IDIOT-PROOF
Pin Pin Name
1+5V
2+5V
3A_D4B_D5A_D+
6B_D+
7GND
8GND
9GND
41 PCM-9361 User Manual
Appendix A PIN Assignments
Matching Cable : 1703100121
Table A.3: CN3: Internal USB
Part Number 1653005260
Footprint HD_5x2P_79_N10
Description PIN HEADER 2*5P 180D(M) 2.0mm SMD IDIOT-PROOF
Pin Pin Name
1+5V
2+5V
3A_D4B_D5A_D+
6B_D+
7GND
8GND
9GND
Table A.4: CN4: SATA
Part Number 1654002320
Footprint FOX_LD1107V-S33T5
Description Serial ATA 7P 1.27 90D(M) SMD LD110 7V-S33T5
Pin Pin Name
1GND
2TX+
3TX4GND
5RX6RX+
7GND
PCM-9361 User Manual 42
Table A.5: CN5: SATA
Part Number 1654002320
Footprint FOX_LD1107V-S33T5
Description Serial ATA 7P 1.27 90D(M) SMD LD1107V-S33T5
Pin Pin Name
1GND
2TX+
3TX4GND
5RX6RX+
7GND
Table A.6: CN6: Power Switch (Low Active )
Part Number 1655302020
Footprint WF_2P_79_BOX_R1_D
Description WAFER BOX 2P 180D(M) 2.0mm W/Lock
Pin Pin Name
1 PSIN
2GND
Table A.7: CN7: PCI-104 -12 V Input
Part Number 1653002101
Footprint JH2X1V-2M
Description PIN HEADER 2*1P 180D(M)SQUARE 2.0mm DIP W/O Pb
Pin Pin Name
1 -12 V
2GND
43 PCM-9361 User Manual
Appendix A PIN Assignments
Matching Cable : 1700000265
Table A.8: CN8: AT/ATX Power Input
Part Number 1655412090
Footprint ATXCON-2X6V-42
Description Power CONN.6*2P 180D(M) DIP W/Fixed Lock
Pin Pin Name
1GND
2+5V
3+5V
4GND
5+5V
6+5V
7GND
8GND
9+5VSB
10 PSON#
11 GND
12 +12V
Table A.9: CN9: PCI-104
Part Number 00A0000020 1653130428
Footprint PC104-PCI-PLUS
Description PCI-104
Pin Pin Name
PA1 GND
PA2 VI/O (+5V or +3.3V)
PA3 AD05
PA4 C/BE0#
PA5 GND
PA6 AD11
PA7 AD14
PA8 +3.3V
PA9 SERR#
PA10 GND
PA11 STOP#
PCM-9361 User Manual 44
PA12 +3.3V
PA13 FRAME#
PA14 GND
PA15 AD18
PA16 AD21
PA17 +3.3V
PA18 IDSEL0
PA19 AD24
PA20 GND
PA21 AD29
PA22 +5V
PA23 REQ0#
PA24 GND
PA25 GNT1#
PA26 +5V
PA27 CLK2
PA28 GND
PA29 +12V
PA30 -12V
PB1 NC
PB2 AD02
PB3 GND
PB4 AD07
PB5 AD09
PB6 VI/O (+5V or +3.3V)
PB7 AD13
PB8 C/BE1#
PB9 GND
PB10 PERR#
PB11 +3.3V
PB12 TRDY#
PB13 GND
PB14 AD16
PB15 +3.3V
PB16 AD20
PB17 AD23
PB18 GND
PB19 C/BE3#
PB20 AD26
PB21 +5V
PB22 AD30
PB23 GND
PB24 REQ2#
PB25 VI/O (+5V or +3.3V)
PB26 CLK0
PB27 +5V
PB28 INTD#
Table A.9: CN9: PCI-104
45 PCM-9361 User Manual
Appendix A PIN Assignments
PB29 INTA#
PB30 REQ3#
PC1 +5V
PC2 AD01
PC3 AD04
PC4 GND
PC5 AD08
PC6 AD10
PC7 GND
PC8 AD15
PC9 NC
PC10 +3.3V
PC11 LOCK#
PC12 GND
PC13 IRDY#
PC14 +3.3V
PC15 AD17
PC16 GND
PC17 AD22
PC18 IDSEL1
PC19 VI/O (+5V or +3.3V)
PC20 AD25
PC21 AD28
PC22 GND
PC23 REQ1#
PC24 +5V
PC25 GNT2#
PC26 GND
PC27 CLK3
PC28 +5V
PC29 INTB#
PC30 GNT3#
PD1 AD00
PD2 +5V
PD3 AD03
PD4 AD06
PD5 GND
PD6 M66EN
PD7 AD12
PD8 +3.3V
PD9 PAR
PD10 NC
PD11 GND
PD12 DEVSEL#
PD13 +3.3V
PD14 C/BE2#
PD15 GND
Table A.9: CN9: PCI-104
PCM-9361 User Manual 46
PD16 AD19
PD17 +3.3V
PD18 IDSEL2
PD19 IDSEL3
PD20 GND
PD21 AD27
PD22 AD31
PD23 VI/O (+5V or +3.3V)
PD24 GNT0#
PD25 GND
PD26 CLK1
PD27 GND
PD28 RST#
PD29 INTC#
PD30 GND
Table A.9: CN9: PCI-104
47 PCM-9361 User Manual
Appendix A PIN Assignments
Table A.10: CN10: 36 bits LVDS Panel
Part Number 1653920200
Footprint SPH20X2
Description *CONN. 40P 90D 1.25mm SMD WO/Pb DF13-40DP-1.25V
Pin Pin Name
1 +5V or +3.3V
2 +5V or +3.3V
3GND
4GND
5 +5V or +3.3V
6 +5V or +3.3V
7 LVDS0_D08 LVDS1_D09 LVDS0_D0+
10 LVDS1_D0+
11 GND
12 GND
13 LVDS0_D114 LVDS1_D115 LVDS0_D1+
16 LVDS1_D1+
17 GND
18 GND
19 LVDS0_D220 LVDS1_D221 LVDS0_D2+
22 LVDS1_D2+
23 GND
24 GND
25 LVDS0_CLK26 LVDS1_CLK27 LVDS0_CLK+
28 LVDS1_CLK+
29 GND
30 GND
31 DDC_CLK
32 DDC_DAT
33 GND
34 GND
35 NC
36 NC
37 NC
38 NC
39 NC
40 NC
PCM-9361 User Manual 48
Table A.11: CN11: LPT
Part Number 1653213260
Footprint BH13X2SV
Description BOX HEADER 13*2P 180D(M) 2.0mm SMD
Pin Pin Name
1 STROBE#
2 AUTOFEED#
3D0
4ERROR#
5D1
6INIT#
7D2
8SLCT IN#
9D3
10 GND
11 D4
12 GND
13 D5
14 GND
15 D6
16 GND
17 D7
18 GND
19 ACK#
20 GND
21 BUSY
22 GND
23 PE
24 GND
25 SLCT
26 NC
49 PCM-9361 User Manual
Appendix A PIN Assignments
Matching Cable : 1700260250
Table A.12: CN12: GPIO
Part Number 1653005261
Footprint HD_5x2P_79_BOX
Description PIN HEADER SMD 5*2P 180D(M) 2.0mm
Pin Pin Name
1+5V
2GPIO4
3GPIO0
4GPIO5
5GPIO1
6GPIO6
7GPIO2
8GPIO7
9GPIO3
10 GND
Table A.13: CN13: 18 bits TTL Panel
Part Number 1653920200
Footprint SPH20X2
Description *CONN. 40P 90D 1.25mm SMD WO/Pb DF13-40DP-1.25V
Pin Pin Name
1+5V
2+5V
3GND
4GND
5 +3.3V
6 +3.3V
7NC
8GND
9NC
10 NC
11 PD2
PCM-9361 User Manual 50
12 PD3
13 PD4
14 PD5
15 PD6
16 PD7
17 NC
18 NC
19 PD10
20 PD11
21 PD12
22 PD13
23 PD14
24 PD15
25 NC
26 NC
27 PD18
28 PD19
29 PD20
30 PD21
31 PD22
32 PD23
33 GND
34 GND
35 SHFCLK
36 FLM (V-SYNC)
37 M/DE
38 LP (H-SYNC)
39 NC
40 ENVEE
Table A.13: CN13: 18 bits TTL Panel
51 PCM-9361 User Manual
Appendix A PIN Assignments
Table A.14: CN14: Inverter Power Output
Part Number 1655305020
Footprint WHL5V-2M
Description WAFER BOX 2.0mm 5P 180D(M) W/LOCK
Pin Pin Name
1+12V
2GND
3 ENABKL
4 VBR
5+5V
Table A.15: CN15: HDD & PWR LED
Part Number 1655306020
Footprint WHL6V-2M
Description WAFER BOX 2.0mm 6P 180D(M) W/LOCK
Pin Pin Name
1+5V
2GND
3 Power LED+
4 Power LED5 HDD LED+
6 HDD LED-
PCM-9361 User Manual 52
Matching Cable : 1701140201
Table A.16: CN16: SMBus
Part Number 1655904020
Footprint FPC4V-125M
Description Wafer SMT 1.25mmS/T type 4P 180D(M) 85205-04001
Pin Pin Name
1GND
2SMB_DAT
3SMB_CLK
4+5V
Table A.17: CN17: COM2
Part Number 1653207260
Footprint HD_7x2_79_BOX
Description BOX HEADER SMD 7*2P 180D(M) 2.0mm
Pin Pin Name
1DCD#
2DSR#
3RXD
4RTS#
5TXD
6CTS#
7DTR#
8RI#
9GND
10 GND
11 422/485TX+
12 422/485TX13 422RX+
14 422RX-
53 PCM-9361 User Manual
Appendix A PIN Assignments
Table A.18: CN18: LAN
Part Number 1652000174
Footprint RJ45-P62P071AX9
Description PhoneJack RJ45 14P 90D(F) W/Xfam P26@P07-1AX9
Pin Pin Name
1 TX+(10/100)
2 TX-(10/100)
3 RX+(10/100)
4NC
5NC
6 RX-(10/100)
7NC
8NC
Table A.19: CN19: CPU FAN (+5V)
Part Number 1655303020
Footprint WHL3V-2M
Description WAFER BOX 2.0mm 3P 180D w/LOCK
Pin Pin Name
1 Speed
2+5V
3GND
PCM-9361 User Manual 54
Matching Cable : 1700060202
Table A.20: CN20: External USB
Part Number 1654904105
Footprint USB-V-4A
Description USB CON. 4P 90D(F) DIP A TYPE RoHS
Pin Pin Name
1+5V
2D3D+
4GND
Table A.21: CN21: PS2
Part Number 1654003199
Footprint CONTEK_MQN3261F1G400
Description MINIDIN 6P Short body W/Shielding90D(F) DIP
Pin Pin Name
1 KBDAT
2MSDAT
3GND
4+5V
5 KBCLK
6MSCLK
55 PCM-9361 User Manual
Appendix A PIN Assignments
Table A.22: CN22: COM1
Part Number 1654000056
Footprint DBCOM-VM5MS
Description D-SUB CON. 9P 90D(M)DIP 070241MR009S200ZU SUYIN
Pin Pin Name
1 DCD#
2RXD
3TXD
4DTR#
5GND
6DSR#
7RTS#
8CTS#
9RI#
Table A.23: CN23: VGA
Part Number 1654000055
Footprint DBVGA-VF5MS
Description D-SUB Conn. 15P 90D(F) DIP 070242FR015S200ZU
Pin Pin Name
1RED
2GREEN
3BLUE
4NC
5GND
6GND
7GND
8GND
9NC
10 GND
11 NC
12 DDAT
13 HSYNC
14 VSYNC
15 DCLK
PCM-9361 User Manual 56
Table A.24: CN24: CF
Part Number 1653000106
Footprint CF_50P_N7E50-H516RA-50
Description CF HEADER 50P 90D(M)SMD typeII N7E50-H516RA-50
Pin Pin Name
1GND
2D03
3D04
4D05
5D06
6D07
7CS0#
8GND
9GND
10 GND
11 GND
12 GND
13 +5V
14 GND
15 GND
16 GND
17 GND
18 A02
19 A01
20 A00
21 D00
22 D01
23 D02
24 NC
25 CD2#
26 CD1#
27 D11
28 D12
29 D13
30 D14
31 D15
32 CS1#
33 VS1#
34 IORD#
35 IOWR#
57 PCM-9361 User Manual
Appendix A PIN Assignments
36 WE#
37 IREQ
38 +5V
39 CSEL#
40 VS2#
41 RESET
42 IORDY
43 INPACK#
44 REG#
45 DASP#
46 PDIAG#
47 D08
48 D09
49 D10
50 GND
Table A.24: CN24: CF
PCM-9361 User Manual 58
Table A.25: CN25: DDR2 SO-DIMM H=6.5mm
Part Number 1651000068
Footprint DDR-SODIMM-RVS65
Description SKT DIMM 200P DDR2 H=6.5mm RVS SMD 1612773-4
Pin Pin Name
1VREF
2GND
3GND
4DQ59
5DQ63
6DQ58
7DQ62
8GND
9GND
10 DM7
11 DQS#7
12 GND
13 DQS7
14 DQ57
15 GND
16 DQ56
17 DQ61
18 GND
19 DQ60
20 DQ51
21 GND
22 DQ50
23 DQ55
24 GND
25 DQ54
26 DM6
27 GND
28 GND
29 DQS#6
30 CK1
31 DQS6
32 CK1#
33 GND
34 GND
35 DQ53
36 DQ49
37 DQ52
38 DQ48
39 GND
40 GND
41 GND
42 GND
59 PCM-9361 User Manual
Appendix A PIN Assignments
43 DQ47
44 DQ43
45 DQ46
46 DQ42
47 GND
48 GND
49 DQS#5
50 NC
51 DQS5
52 DM5
53 GND
54 GND
55 DQ45
56 DQ41
57 DQ44
58 DQ40
59 GND
60 GND
61 DQ39
62 DQ35
63 DQ38
64 DQ34
65 GND
66 GND
67 DM4
68 DQS#4
69 NC
70 DQS4
71 GND
72 GND
73 DQ37
74 DQ33
75 DQ36
76 DQ32
77 GND
78 GND
79 CKE0
80 CKE1
81 +1.8V
82 +1.8V
83 NC
84 NC
85 BA2
86 NC
87 +1.8V
88 +1.8V
89 A12
Table A.25: CN25: DDR2 SO-DIMM H=6.5mm
PCM-9361 User Manual 60
90 A11
91 A9
92 A7
93 A8
94 A6
95 +1.8V
96 +1.8V
97 A5
98 A4
99 A3
100 A2
101 A1
102 A0
103 +1.8V
104 +1.8V
105 A10
106 BA1
107 BA0
108 RAS#
109 WE#
110 SCS#0
111 +1.8V
112 +1.8V
113 CAS#
114 ODT0
115 SCS#1
116 A13
117 +1.8V
118 +1.8V
119 ODT1
120 NC
121 GND
122 GND
123 DQ31
124 DQ27
125 DQ30
126 DQ26
127 GND
128 GND
129 DQS#3
130 DM3
131 DQS3
132 GND
133 GND
134 DQ25
135 DQ29
136 DQ24
Table A.25: CN25: DDR2 SO-DIMM H=6.5mm
61 PCM-9361 User Manual
Appendix A PIN Assignments
137 DQ28
138 GND
139 GND
140 DQ19
141 DQ23
142 DQ18
143 DQ22
144 GND
145 GND
146 DQS#2
147 DM2
148 DQS2
149 GND
150 GND
151 DQ21
152 DQ17
153 DQ20
154 DQ16
155 GND
156 GND
157 DQ15
158 DQ11
159 DQ14
160 DQ10
161 GND
162 GND
163 NC
164 CK0
165 GND
166 CK0#
167 DQS#1
168 GND
169 DQS1
170 DM1
171 GND
172 GND
173 DQ13
174 DQ9
175 DQ12
176 DQ8
177 GND
178 GND
179 DQ7
180 DQ3
181 DQ6
182 DQ2
183 GND
Table A.25: CN25: DDR2 SO-DIMM H=6.5mm
PCM-9361 User Manual 62
184 GND
185 DM0
186 DQS#0
187 GND
188 DQS0
189 DQ5
190 GND
191 DQ4
192 DQ1
193 GND
194 DQ0
195 SDA
196 GND
197 SCL
198 SA0
199 +3.3V
200 SA1
Table A.25: CN25: DDR2 SO-DIMM H=6.5mm
63 PCM-9361 User Manual
Appendix A PIN Assignments
Table A.26: CN26: Reset Button
Part Number 1601003501
Footprint SW-PT-035-C
Description PUSH SW SMD 4P 12V 50mA WO/Pb EVQPSR02K
Pin Pin Name
1 RESET#
2 RESET#
3GND
4GND
Please verify specifications before quoting. This guide is intended for reference
purposes only.
All product specifications are subject to change without notice.
No part of this publication may be reproduced in any form or by any means,
electronic, photocopying, recording or otherwise, without prior written permission of the publisher.
All brand and product names are trademarks or registered trademarks of their
respective companies.
© Copyright of the manufactuer, 2009
Loading...