Award ORCA Installation Manual

ORCA Floor Mount Vanity

Installation Guide

1

Rubber

Mallet

Silicone

Pencil

Screwdriver

SAFETY INFORMATION

• Read all instructions before starting installation.

• We recommend that a qualied tradesperson install this vanity.

• This installation is a two-person job due to the weight and size of the product.

• Check the product immediately upon receipt for any missing packs/parts or damage during transit. If any damage

or faults are found, DO NOT install the product - contact our customer service team at Award Brands via toll-free
phone no. 1800 354 435 (outside Victoria) or [phone] inside Victoria. Damage reported after installation
will void the warranty of this product.
NOTE: This vanity unit is to be mounted on a secure surface. Award Brands shall not accept responsibility for any
damage caused by improper installation.

• Depending on the installation, you may need to drill or cut out holes on the back of the vanity to suit your pipe
work, it is recommended that you should measure your pipe work and mark the measurements to the back of the
vanity rst, double check to ensure the measurements and markings are correct before drilling or cutting out holes
at the back of the vanity unit.

• Standard pop-up waste is provided with the vanity top.

• To easily access back of cabinet when installing plumbing pipework, remove drawers as described on Page 3.

• Due to transit, some adjustment to hardware parts maybe required to correct any gaps or alignment issues. (follow

the instructions on page 3).

• Do not stand or sit on this vanity at any time.

October 2015

TOOLS REQUIRED FOR INSTALLATION

Cloth

Drill

Measuring Tape

Methylated

Spirits

Spirit Level

SIZES 900mm & 1200mm

(1) Place the vanity against the wall, use a spirit level to

ensure it is level (Dia. A).

(2) Apply a bead of silicone around the edges of vanity

cabinet and on top panels before assembling the vanity
basin top. (Dia. B)

(3) Place the vanity basin top onto the cabinet (Dia. C) Align

it while silicone is still curing. To prevent any water
penetration behind the vanity use silicone to create a
seal at the joint between the wall and vanity unit. Wipe
off any excess silicone and residue by using a cloth and
methylated spirit or wax/grease remover.

(4) A Licensed plumber must complete all pipe work and

connect water supply lines.

(5) Allow 24 hours for silicone to cure before using this

vanity.

INSTALLATION STEPS

Dia. A

Dia. B

Dia. C

CARE INSTRUCTIONS

e product you have purchased has been designed to provide
many years of dependable service, however, the nish requires
care and maintenance in order to delay the wear that will
eventually occur over time.

It is recommended to clean with a non ammoniated pure liquid
soap to remove any stains or water spots. Ensure to rinse all
traces of soap thoroughly. Use a soft cloth to clean and dry the
product.

DO NOT use any harsh chemicals such as bleach or any
scouring cloth/pad to clean the product as it will scratch the
surface and damage the product nish/surfaces.

2

22

October 2015

3

October 2015

Steps to remove the drawer

Steps to reassemble the drawer

Replace drawer at a slight angle ensuring that the
locating holes in the rear of the drawer engage with
the lugs on the rear of the runners.

Lower the front of drawer onto the front locating lugs.
Replace the retaining screws.

Open the drawer and remove the screw in the
runner from both sides.

Hold the drawer up at a slight angle and take it out
slowly.

PRODUCT WARRANTY

Congratulations! You have purchased a quality product from Award Brands.

is product is covered by a 5 year warranty from the date of purchase. is warranty covers faults in the
product construction, material and assembly where the failure is due to a fault in the manufacture of the
product. Faulty products will be repaired or replaced free of charge for the rst 12 months from the date of
purchase, after which we provide free parts only for the remainder of the warranty period.

is warranty does not include faults caused by

• Unsuitable or improper use of this product

• Incorrect installation

• If installation or part installation is not carried out by a LICENSED PLUMBER for the products which
are required to be installed by a licensed plumber.

• Normal wear and tear

• Inadequate or complete lack of maintenance

• Chemical, electrochemical or electrical inuences

• Harsh detergents or abrasive cleaners used on product nishes

Please note the warranty is extended to the purchaser only and is not transferable.

For warranty service, please contact with our customer service team at Award Brands via toll-free phone no.
1800 354 435 (outside Victoria) or [phone] inside Victoria. Please prepare and provide us with the
following items when you claim a warranty service for this product:

• e original sales receipt as proof of purchase, including the date of purchase.

• When product must be installed by a Licensed Plumber, the proof of receipt is required.

FAILURE TO COMPLY WITH ABOVE WARRANTY GUIDELINE WILL VOID THE WARRANTY

AGREEMENTS

Our goods come with guarantees that can not be excluded under the Australian Consumer Law. You are entitled
to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality

and the failure does not amount to a major failure.

Award Brands Pty Ltd
ABN 72 006 390 594

557 Burwood Highway, Knoxeld

Victoria, Australia 3180

Ph [phone]
Ph 1800 354 435 (Outside Victoria)
Fax [phone]
Email [e-mail]

4

October 2015