7.Do not block any ventilation openings. Install in
accordance with the manufacturers instructions.
8.Do not install near any heat sources such as radiators ,
stoves, or other apparatus (including amplifiers)that
produce heat.
9.Protect the power cord from being walked on or
pinched particularly at power outlets, and the point
where they exit from the apparatus.
10.Only use attachments/accessories specified by the
manufacturer.
11.Unplug this apparatus during lightning storms or
when unused for long periods of time.
12.Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as the power-supply cord
or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been
exposed to rain or moisture , does not operate normally,
or has been dropped.
13.Apparatus must not be exposed to dripping or
splashing and no objects filled with liquids, such as
vases, should be placed on the apparatus.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN!
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK).NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
The symbol indicates that dangerous voltages
constituting a risk of electric shock are present
within this unit.
The symbol indicates that there are important
operating and maintenance instructions in the
literature accompanying this unit.
WARNING:
To prevent fire or shock hazard, do not expose this
appliance to rain or moisture.
Thank you very much for purchasing this TV. To enjoy
your product from the very beginning, read this manual
carefully and keep it handy for easy reference.
CAUTION
SAFETY INSTRUCTIONS
INSTALLATION
Locate the TV in the room where light does not strike
the screen .
directly
Total darkness or a reflection on the picture screen can
cause eyestrain. Soft and indirect lighting is recommended
for comfortable viewing.
Allow enough space between the TV and the wall to
permit ventilation.
Avoid extremely warm locations to prevent possible
damage to the cabinet or premature component failure.
This TV can be connected to AC 100-240 Volts. 50/60 Hz.
Never connect to a DC supply or any other power supply.
Do not cover the ventilation openings when using the TV.
CAUTION
Never tamper with any components inside the TV, or any
other adjustment controls not mentioned in this manual.
All LCD-TVs are high voltage instruments. When you
clean up dust or water drops on the LCD PANEL or
CABINET, the power cord should be pulled out from the
receptacle, then wipe the TV with a dry soft cloth. During
thunder and lighting, unplug the power cord and antenna
cord to prevent damage to your TV. All repairs to this TV
should only be performed by qualified TV service personnel.
Warning: Change or modifications to this unit not expressly
by the part responsible for compliance could void the user 's
authority to operate the Equipment.
a. Do not expose to dripping or splashing.
b. No objects filled with liquids, such as vases, shall be
placed on the apparatus.
c. The mains plug of this device is used as the disconnect
device and shall remain readily accessible and operable.
d. No naked flame sources, such as lighted candles, should
be placed on the apparatus.
e. Allow suitable distances around the apparatus for sufficient
ventilation. Ventilation should not be impeded by covering
ventilation openings with items such as newspapers, table
cloths, curtains and such like.
This symbol indicates that this productincorporates
double insulation between hazardous mains voltage
and user accessible parts. When servicing use only
identical replacement parts.
WARNING: To reduce the risk of fire or electric shock,
do not expose this apparatus to rain or cords.
The display panel is a very sensitive and high technology
product, giving you finely detailed pictures. Occasionally,
a few non-active pixels may appear on the screen as a
fixed point of black, blue, green or red. Please note that
this does not affect the performance of your product.
These pixels shall not be regarded as a failure.
-2-
High voltages are used in the operation of this television
receiver. Do not remove the cabinet back from your set.
Refer servicing to qualified service personnel.
INSTALLATION
Never stand on, lean on, or suddenly push the television or
its stand. You should pay special attention to children.
Serious injury may result if it falls.
To prevent fire or electrical shock hazard, do not expose
the television receiver to rain or moisture.
Do not drop or push objects into the television cabinet
slots or openings. Never spill any kind of liquid on the
television receiver.
Do not block the ventilation holes in the back cover.
Adequate ventilation is essential to prevent failure of
electrical components.
Do not place your television on an unstable cart, stand,
shelf or table. Serious injury to an individual , and damage
to the television, may result if it falls.
When the television receiver is not used for an
extended period of time, it is advisable to disconnect
the AC power cord from the AC outlet.
Avoid exposing the television receiver to direct sunlight
and other sources of heat. Do not stand the television
receiver directly on other products which give off heat,
e.g. video cassette players and audio amplifiers. Do not
place naked flame sources, such as lighted candles on
the television.
Do not trap the power supply cord under the television
receiver.
If the television is to be built into a compartment or similar
enclosure, the minimum distances must be maintained. Heat
build-up can reduce the service life of your television, and
can also be dangerous.
Dim:515*320mm(
-3-
INSTALLATION
For wall mounting with the optional bracket, please read the following instruction and the bracket
instruction. Make sure qualified service personnel perform the operation.
AWA bears no responsibility for improper mounting that results in accident or injury.
Wall Mounting Holes Spacing and Location
100 mm
100 mm
4 Wall mount M4 Screws
Base Stand Disassemble Illustration
How to remove the stand from the TV
(The LCD Display is very fragile, and must be protected at all times when removing the
base stand. Be sure that no hard or sharp object, or anything that could scratch or
damage the LCD display, comes into contact with it. DO NOT exert pressure on the front
of the unit at any time because the screen could crack.)
1.Use the screwdriver to remove 4 screws from the screw location.
2.Remove the base stand from the Main body.
-4-
ACCESSORIES
INSTALLATION
AC Power Cord.........................
Infrared Remote Control............
User s M anual ........................
Battery(AAA)........................... 2
FRONT PANEL
6
1
1
1
3
5
4
2
1
30 30
1 2 3
1: Remote control sensor.
4 5 6
7 8 9 0
2: Indicator LED: GREEN POWER ON.
+
CH
VOL
_+_
RED STANDBY.
3: Key board
4: Power: Press this button to turn the unit
ON from STANDBY mode.
Press it again to turn the set back to
STANDBY.
5: AC power switch:Press to turn ON/OFF TV.
6: DVD Player.
-5-
INSTALLATION
KEY BOARD
SOURCE
SOURCE
MENU
MENU
CH+
CH+
CH-
CH-
VOL+
VOL+
VOL-
VOL-
1.SOURCE
To display the input source menu.
2.MENU
To display main MENU.
3.CH+/CHIn TV mode to change the channel up
and down.
In MENU mode, to select the menu items .
In standby mode, it can turn on the TV.
4.VOL+/VOLTo adjust sound level.
In MENU mode,to select the menu items.
REAR PANEL
DVD SIDE PANEL
USB
SD/MMC/MS
Disc data side
NEXT
PREV
STOP
PLAY/PAUSE
OPEN/CLOSE
Disc label side facing you
USB
In DVD mode, press DVD/USB button
on the Remote control, insert a USB or
a MP3 player with USB interface to play
the MP3, JPEG files.
3 in 1 Card Reader
In DVD mode, press DVD/USB button
on the Remote control, you can
insert three kinds of card (SD ,MMC,
MS) to play the mp3 music and JPEG
files. All the function is the same to
playing a disc.
Caution:
When using USB/3 in 1 Card Reader
function, please do not insert in the wrong
direction, or else it will damage the unit.
µçÔ´ÊäÈë
×ó
ÓÒ
All the terminals are(from left to right):
AC POWER SOCKET, HDMI input,VGA ,YPbPr input,AV,Rear Audio input,PC AUDIO input,
ANTENNA SOCKET.
Note: 1.AV and YPbPr share the Rear Audio input channel.
2. When HDMI port get DVI signal ,the audio signal receives from the PC Audio channel.