Page 1
7”17cm Twin Screen Portable DVD Player
USER MANUAL
Please read this Use Manual carefully before using
this product and keep this manual for future reference
DPD-703
Page 2
CONTENTS
Safety and important notice 3
6. Adjust settings 15
3 tnatropmI .1
51 putes lareneG
Copyright statement 3
Copyright notice 3
Copyright notice 3
Region management information 3
2. Your DVD player 5
Product overview 5
Remote control 6
moh roF
3 remialcsiD
Preference setup 18
Password setup 19
4 eciton yrettaB
seton csiD .7
oitacificepS .8
9. Troubleshooting 22
5 tinu niaM
6 rotinom eciV
8 tcennoC .3
8 esu e
51 putes oiduA
71 putes oediV
02
12 n
Connect to power outlet 8
Connect video/audio cables 8
Connect USB device 8
Prepare the remote control 9
Select menu display language 10
Play form USB device and
8 esu rac roF
9 detrats teG .4
01 yalP .5
01 csid morf yalP
11 oediv yalP
31 cisum yalP
31 otohp yalP
41 drac yromem
2
Page 3
1 IMPORTANT
Safety and important notice
Always read the safety instructions
carefully.
Keep this User’s Manual for future
reference.
Lay this equipment on a reliable flat
surface before setting it up. Do not
stand it on soft furnishings.
Where the power plug is used as the
disconnect device, the disconnect
device shall remain readily operable.
The apparatus shall not be exposed to
dripping or splashing and objects filled
with liquids, such as vases, shall not
be placed on the apparatus.
Batteries (battery pack or batteries
installed) shall not be exposed to
excessive heat such as sunshine, fire
or the likes.
If any of the following situation arises,
get the equipment checked by a
service technician:
The equipment has been exposed
to moisture.
The equipment has been dropped
and damaged.
The equipment has obvious sign of
breakage.
The equipment has not been
working well or you cannot get it
work according to User’s Manual.
To prevent the risk of electric shock,
do not open the cover or the back of
the receiver.
Do not block the ventilation holes of
the device. Leave appropriate gap
above and around it to allow for
adequate ventilation.
Do not place the device in an
unventilated cabinet or on top of a unit
which emits heat.
Copyright Statement
No part of this publication may be
reproduced in any form by any means
without the prior written permission.
Other trademarks or brand names
mentioned herein are trademarks or
registered trademarks of their respective
companies.
Disclaimer
Information in this document is subject to
change without notice. The manufacturer
does not make any representations or
warranties (implied or otherwise) regarding
the accuracy and completeness of this
document and shall in no event be liable
for any loss of profit or any commercial
damage, including but not limited to
special, incidental, consequential, or other
damage.
Copyright notice
This product incorporates copyright
protection technology that is protected by
method claims of certain U.S. patents and
other intellectual property rights owned by
Macrovision Corporation and other rights
owners. Use of this copyright protection
technology must be authorized by
Macrovision Corporation, and is intended
for home and other limited viewing uses
only unless otherwise authorized by
Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
Region Management Information
Region Management Information: This
DVD Player is designed and manufactured
to respond to the Region Management
Information that is recorded on a DVD disc.
If the Region number described on the
DVD disc does not correspond to the
Region number of this DVD Player, this
DVD Player cannot play this disc.
3
Page 4
BATTERY NOTICE
The Main Portable DVD player uses the
built-in lithium battery and it is not
detachable.
Charging the battery:
Connect the power adapt or to the power
outlet and the DV terminal to the DC IN jack
on the side of the DVD player. Then be
sure to let the power switch to "OFF"
state. If the power switch in "ON" state, it
can not charge the battery.
Charging indicator:
On the side of the main DVD player, there
is a charge/power indicator. When charging
on (power off state), the indicator turns red.
If charging full, the indicator turns off. When
in power on state (not charging), the
indicator turns green.
4. Don’t drop the main DVD player into the
water or store it with the wet battery.
5. If the main unit should be stored with a
long time, please charge the battery for
over 2 hours (let the battery with 50%
power).
6. Use the matched the power adaptor.
The adaptor that over the specified
voltage, current or modified is prohibited
to use.
Please read the instruction below
carefully, your incorrect using will lead the
battery to be too heat, fired, ruptured,
damaged and exhausted.
Charging time:
To charge battery please use original
adapter, it will take about 3.5-4 hours to
fully charge the empty standard battery.
Low battery display:
When the battery is too lower, the low
battery information will appear on the
screen. Then you should charge the
battery.
Warning
1. Products with the battery inside can not
be placed in fire or heating, and can not
be stored in high temperature
environment ( above 80 ).
ć
2. Can not drive the nails into the battery
part of the main unit or beat the battery
part with a hammer.
3. Can not disassemble the main unit and
transform the Internal and external
structure of the battery.
4
Page 5
2 YOUR DVD PLAYER
PRODUCT OVERVIEW
4. LEFT/FR (Fast reverse)
On media play, press to fast reverse.
In menu interface, press to select item
left.
Main unit (DVD player)
Front View
21
1 2 3 4 5 6 7 8
Side View
5. VOL-
Decrease the volume level.
6. IR (Remote sensor)
7. PLAY/PAUSE
Start, pause or resume disc play.
8. VOL+
Increase the volume level.
9. RIGHT/FF (Fast forward)
On media play, press to fast forward.
In menu interface, press to select item
right.
10 11
9
2212
10. DOWN/NEXT
On media play, press to select the next
track.
20
19
In menu interface, press to select item
down.
18
17
16
15
14
13
1. 7 inch LCD monitor
2. USB/CARD
When the unit is on, press it to select
the different mode, such as DVD, SD or
USB mode.
3. UP/PREV
On media play, press to select the
previous track.
In menu interface, press to select item
up.
11. Speaker
12. MENU
Press to access or exit the disc menu.
13. Release switch
Slide the switch to release the monitor
panel then pull open the panel to display
the disc compartment.
14. AV OUT jack
15. DC IN jack
16. POWER OFF/ON Switch
17. SD/MMC/MS interface
18. USB interface
19. Earphone jack
20. Charge/Power indicator
21&22. Beckets
Through the beckets to fix the unit
to the headrest of the car.
5
Page 6
Vice Monitor
Front View
Remote control
11
1
Side View
32 4 5 6 7 8 9
18
17
16
15
14
13
1. 7 inch LCD monitor
2. Speaker
3. MUTE
4. UP
5. LEFT/VOL-
6. TFT ON/OFF
7. RIGHT/VOl+
8. DOWN
9. MENU
10. Speaker
11&12. Beckets
13. AV IN jack
14. DC OUT jack
15. POWER OFF/ON Switch
10 12
1. TFT ON/OFF
Press to switch on or off the TFT display
and not to switch off the power.
2. PROG
Press to enter program mode to play the
track in your desired sequence.
3. ZOOM
If available, press to allow the picture to
be increased in size (x2, x3, x4, x1/2,
x1/3, 1/4, off).
4. SLOW
For some discs, press to start slow
forward function. Press repeatedly to
change the search speed (X1/2, X1/4,
X1/8, X1/16).
5. TV MODE
Switch the different video system mode,
such as 16:9, 4:3.
6. STEP
Press to enter single step play.
16. DC IN jack
17. Earphone jack
18. Power indicator
7. ANGLE
Press to change the view angle on
multi-angle DVD disc.
6
Page 7
8. SUBTITLE
21. 0-9
Press to display the subtitle information
of the DVD disc.
9. SHIFT
Press to active the function of the
complex buttons (0-9) on or off.
When shift off, the 0-9 buttons is numeric
key function. When shift on, pressing the
0-9 buttons is the other function, such as
ZOOM, SLOW function.
10.
Press to skip to the previous title,
chapter, or track.
11.
Search fast backward. Press repeatedly
to change the search speed (X2, X4, X8,
X16, X32).
12. ENTER
Press to confirm an entry or selection.
13. SETUP
Access or exit the setup menu.
14.
Press to skip to the next title, chapter, or
track.
15. REPEAT
In media play mode, press to switch
the repeat mode of discs.
16. A-B
A-B repeat allows a passage to be
repeated continuously.
17. MUTE
Press to mute the sound, press it
again to resume the sound.
18. DISPLAY
For disc, display the current status or
disc information.
19. 4
Numeric button 4
20. N/P
Press to select the NTSC or PAL mode.
Numeric buttons. Select an item to play.
mode.
22. TIME
Press to enter the search interface. You
can input the title, chapter, time or other
information by numeric buttons and
press ENTER to confirm. Then it will
skip to the corresponding position to
play.
23. AUDIO
Select an audio language/channel.
24.
Press it to stop the media play.
25. (PLAY/PAUSE)
Press to start, pause or resume disc
play.
26. VOL+
Press to increase the volume level.
27.
Search fast forward. Press repeatedly to
change the search speed (X2, X4, X8,
X16,X32).
28. VOL-
Press to decrease the volume level.
29. TITLE
Press to display the title menu of the
DVD disc.
30. USB/CARD
When the unit is on, press it to select
the different mode, such as DVD, SD or
USB mode.
31. MENU
* For DVD disc, press to Access or exit
the disc menu.
* For VCD/SVCD, turn PBC (Playback
Control) on or off in PBC mode.
Note: In case of menu mode, the buttons
(10, 14, 11, 27) (
/ , / ) on the
remote control served as navigation
buttons to select item up/down and
left/right.
7
Page 8
3 CONNECT
Connect USB device/Memory card
A. For home use (the main unit)
On the back of the uni t there is a bracket.
When you pull out the bracket, you can
place the main unit on the flat position to
operate it.
Connect to power outlet
Connect the one terminal of the power cord
to the DC IN jack on the side of the unit and
the plug to the power outlet.
The DVD player is ready to be set up for
use.
gRisk of product damage! Ensure that the
power supply voltage corresponds to the
voltage range for the DVD player.
Connect Video/Audio cables
Make the following basic connections to
use the DVD player.
Connect the video/audio cable to the AV
OUT jack on the side of the main unit.
g Video/Audio cables
Audio left channel (WHITE)
Audio right channel (RED)
Connect the USB flash drive to the USB
jack on the side of the DV D player or insert
the memory card to the SD/MMC/MS
interface.
Note:
gThis DVD player can only play/view MP3,
WMA or JPEG files that are stored on
such devices.
gPress USB/CARD button on the remote
control to select the mode to play the files
on the USB or memory card.
B. For car use (the main unit with
the vice monitor)
On the back of the main unit and the vice
monitor there are two beckets. Through the
beckets to fix the unit to the headrest of the
car. It is convenient for two people on the
backseats to enjoy the program.
Connect to power
Connect the jack of the cigarette lighter
cable to the DC IN 9V jack on the side of
the vice monitor and the other plug to the
car.
Vice monitor
Video channel (YELLOW)
丝印白色
TV
8
Page 9
Connect the main unit with the
vice monitor
Use the cable to connect the two units.
丝印白色
4 GET STARTED
Prepare the remote control
1. Insert finger into A, B place, then press
down A as arrow and take out battery
compartment.
2. Insert the new battery. Make sure that the
facing up.
3. Push the compartment to the original
position.
Battery: One button cell lithium
battery (CR2025).
Caution
g Remove the battery if they are exhausted
or if the remote control is not to be used
for a long time.
gBattery contains chemical substances.
They should be disposed off properly.
9
Page 10
Navigate through the menu
1 Point the remote control directly at the
remote sensor on this DVD player and
select the desired function.
g Point the remote control towards the
remote control signal receiver on the
player front face.
g Operation angle: About ±30 degree in
each the direction of the front of the
remote sensor.
2 Use the following buttons on the remote
control to navigate through the
on-screen menus.
Button Function
5 PLAY
Play from disc
gDVDs and DVD players are designed with
regional restrictions. Ensure that the
DVD video you play is for the same
region zone as the player.
gThis DVD player can support play of the
following file formats: MP3/WMA/JPEG/
DIVX.
Play a disc
Caution
() / ( ) Move up or down.
( ) / ( ) Move left or right.
ENTER Confirm a selection.
0-9 numeric keys Enter numbers
Select menu display language
Press SETUP button on the remote
1
control.
The system setup menu is displayed.
2 Select the [OSD Lang], then press
( ) button.
gNever place any objects other that
discs into the disc compartment.
1 Slide the release switch button on the
side of the main unit to release the
monitor panel then pull it open to
display the disc compartment.
2 Place a disc with label facing up.
3 Close the monitor panel and start disc
play.
4 To stop disc play, press
Tip
gIf the password entry menu is displayer,
you have to enter the password before it
can be played.
gIf you pause or stop a disc for about
several minutes, the screen saver
activates. To deactivate the screen
saver, press SETUP button and select
Screen saver item to set.
button.
10
Page 11
Button Function
Play video
Note
gFor video disc, play always resume
form the point where it was last
stopped. To start play from the
beginning, press
while the message is displayed.
Control a title
1 Play a title
2 Use the remote control to control the
title.
Button Function
()/ ( ) Skip to the previous or
next title or chapter.
( ) button
AUDIO
SUBTITLE
ZOOM
DISPLAY
Change audio language.
· Only applicable to discs with
multiple audio language or
channel.
Change subtitle language.
gOnly applicable to discs with
multiple subtitle language.
Toggle between screen aspect
ratio and different zoom factor.
gTo pan through the zoomed
image, press the navigation
buttons (
Display the current status or
disc information.
/ , / ).
Note
gSome operations may not work with
some discs. See the information
accompanying the disc for details.
( )/ ( ) Searches fast-backward
or fast-forward.
gPress repeatedly to
change the search
speed.
Start, pause or resume
disc play.
Stop disc play.
SLOW Searches slow-forward.
gPress repeatedly to
change the search
speed.
Change video play
1 Play a title
2 Use the remote control to change the
video play.
Access DVD menu
1 Press MENU button to access the disc
main menu.
2 Select a play option, then press
ENTER .
gIn some menus, press the numeric
buttons (0-9) to input your selection.
gTo return to the title menu during play,
press TITLE button.
Access VCD menu
When PBC (Playback Control) for
VCD/SVCD is on, load in a VCD/SVCD, the
contents menu is displayed.
1 Press numeric buttons (0-9) to select a
play option, then press ENTER to start
play.
gIf PBC is off, it skips the menu and
starts play from the first track.
gDuring play, press MENU button to
select PBC on or off.
gWhen PB is on, press TITLE button to
return to the menu.
11
Page 12
Preview disc information
1 During play, press the DISPLAY button.
The disc information is displayed.
For example: DVD
Title Elapsed -->Title Remain--> Chapter
Elapsed --> Chapter Remain --> Display
Repeat play – video
For DVD/VCD/SVCD
1 During play, press the REPEAT button.
2 Each time the button is pressed, the
repeat mode changes in sequential
order.
off
Quick skip play to a specific time
1 During play, press the TIME button.
The Search menu is displayed.
Such as for DVD:
2 Select the Title, Chapter, Tt Time, Ch
Time, then press
( ) button.
3 Press the numeric buttons (0-9) to
change the item or time where you want
to skip to.
4 And you can set the Repeat mode,
Subtitle, Audio, Angle mode in this
interface.
Note
gFor VCD/SVCD, repeat play is only
possible if PBC mode is turned off.
Set repeat play for a specific section
1 During play, press the A-B button first at
the start of the required passage, “A” will
appear.
2 Press A-B button secondly at the end of
the passage, “Ab ” will appear.
Then the unit will repeat playing the
passage you just set from A to B.
3 Press A-B button again will cancel repeat
play.
Note
gThe marked section for repeat play in
only possible within a title or track.
Play the disc in programmed order
For DVD
1 During play, press the PROG button to
display the Program menu.
View DVD play from different angles
1 During play, press the ANGLE button.
2 Each time the button is pressed, the
angle changes in sequential order.
Note
gOnly applicable to discs contain
sequences recorded from different
camera angles.
2 Use the
()/ ( ) button and numeric
buttons to input the title and the chapter
then press ENTER button to confirm.
12
Page 13
3 Use the ( )/ ( ) to select Start on
the bottom of the screen then press
ENTER to confirm. And the unit will play
the contents you programmed.
4 If you want to clear the program, press
PROG button to enter the Program
interface then select Stop on the screen
and press ENTER on the remote control
to confirm, and the unit will cancel the
programmed play.
For VCD (when PBC OFF) /CD/MP3/WMA
In program play mode, you can play the
track in your desired sequence. How to
operation please refer to the DVD disc
program operation.
Play music
Control a track
1 Play a track.
2 Use the remote control to control the
track.
TIME
On the search menu,
use the numeric buttons
to change the
time/number where you
want to skip to.
Repeat play – audio
For audio CD
1 During play, press the REPEAT button.
2 Each time the button is pressed, the
repeat mode changes in sequential
order.
Play MP3/WMA music
MP3/WMA is a type of highly compressed
audio file (file with .mp3, .wma extensions).
1 Insert a disc that contains the MP3/WMA
music. A contents menu is displayed and
play starts.
2 Select a track to play if play does not start
automatically.
To select another track/folder, press
()/ ( ) button, then press ENTER.
Button Function
Start, pause or resume
disc play.
Stop disc play.
()/ ( ) Skip to the previous or
next track.
( )/ ( )
Searches fast-backward
or fast-forward.
gPress repeatedly to
change the search
speed.
0-9 numeric
keys
Select an item to play.
Play photo
Play photos as slideshow
This DVD player can play JPEG photos
(files with .jpeg or .jpg extensions).
1 Insert a disc that contains the JPEG
photos.
For a Kodak disc, the slideshow begins
automatically.
13
Page 14
For a JPEG disc, the photo menu is
displayed.
2 Select the folder/album you want to play.
Press MENU to display the photo menu.
To select a photo, press the navigation
buttons.
To preview the selected photo only, press
ENTER button.
3 Press to start slideshow play.
Control photo play
1 Play photo slideshow.
2 Use the remote control to control the
photo.
Button Function
Start, pause or resume
disc play.
Stop disc play.
()/ ( )
Skip to the previous or
next photo.
Play from USB device and memory
card
This DVD player plays/views MP3, WMA,
or JPEG files that are stored on USB
device or memory card.
1 Connect a USB flash drive or a memory
card to the USB jack or memory card
interface on this DVD player.
2 Press USB/CARD button to select USB
or memory card mode. A contents menu
is displayed and play starts.
3 Select a file to play if play does not start
automatically.
For more information, see chapters “Play
music, Play photo, Play video” for details.
4 To stop play, press
5 When this is a disc on the DVD player, to
switch to the disc mode, press
USB/CARD to select DVD mode.
.
( )/ ( )
0-9 numeric
keys
ZOOM
Rotate the photo
anti-clockwise or
clockwise.
Select an item to play.
Toggle between screen
aspect ratio and different
zoom factor.
· To pan through the
zoomed image, press
the navigation buttons
(
/ , / ).
Tip
gIf the device does not fit into the USB
jack, connect it through a USB
extension cable.
14
Page 15
6 ADJUST SETTINGS
This section describes the various setting
options of the DVD player.
[General Setup] [Audio Setup] [Video Setup]
[Preference Page] [Password Setup] [Exit
Setup]
1 Press SETUP button to display the setup
menu.
2 Use the navigation buttons
select item left, right, up or down.
3 Press ENTER to confirm your selection.
4 To exit the menu, press SETUP . You can
also move the cursor to the
then press ENTER button to exit.
( / , / ) to
position
g[Wide] – for wide –screen TV (frame ratio
16:9).
Note the TV Display item only can be
adjusted when pressing SETUP button in
DISC STOP mode or no disc in the unit.
[Angle Mark]
g[On] – When set on, the angle mark will
display on the screen if a disc
with angle information is playing.
g[Off] – When set off, the angle mark will
not appear on the screen.
[OSD language]
Select the default on-screen menu
language. Such as English.
[Captions]
You can set the captions On or Off. If you
set it On, when the captions will display on
the screen. When set off, the captions will
be hided.
General setup
[TV Display]
Select the screen format according to how
you want the picture to appear on the TV.
g[Normal/Ps] – for standard TV, a
full-height screen display with the sides
trimmed.
g[Normal/Lb] – for standard TV, a
‘wide-screen’ display with black bars on
the top and bottom.
[Screen saver]
Select Screen saver item to set on or off to
activate the screen saver or deactivate the
screen saver.
[Last Memory]
Select the Last Memory item to set on or off.
When set it On, the disc will resume the
play at the last position. If set it to Off, when
you stop the play and start play again, it will
play from the beginning.
Audio setup
15
Page 16
[Speaker Setup]
Select the [Speaker Setup] then press
ENTER or Right-direction button to enter
the Speaker Setup Page.
- [Downmix]
g[Lt/Rt] – if you want to use Dolby
ProLogic decoder to extend 2CH to
4CH, you should select this option.
g[Stereo] – if you want to enjoy original
music or Karaoke, you should select
this option.
g[R-Mono] – When you are enjoying
Karaoke and want to listen the only
Right mono track, please select this
option.
g[Mix-Mono] – it will be sound like in a
movie theatre by using two speakers
system.
- [Dynamic]
Choose this setting to adjust the line out
ratio and get different effect. If set to FULL,
the audio signal peak value will be the
minimum; when set to OFF, the peak
value will be the maximum.
- [Post Drc]
You can set the dynamic digital out On, Off
or Auto.
[Dolby Digital Setup]
- [Dual Mono]
g[Stereo] – if you want to enjoy original
music or Karaoke, you should select
this option.
g[L-Mono] – When you are enjoying
Karaoke and want to listen the only left
mono track, please select this option.
[Equalizer page]
- [Eq Type]
You can set the Equalizer type among
None, Rock, Pop, Live, Dance, Techno,
Classic and Soft.
- [Bass Boost] --- On or Off.
- [Super Bass] --- On or Off.
- [Treble Boost] --- On or Off.
16
Page 17
[3d Processing page]
[Video Quality Setup]
Select a virtual surround sound effect that
is produced from the left and right audio
channels, such as concert, living room, hall,
bathroom and etc.
[Hdcd Setup page]
HDCD --- high definition compatible digital
There are two sampling mode: 1x, 2x. You
can choose one when you connect use the
HDMI cable to enjoy the high definition
effect. If is for the unit with HDMI interface.
Video setup
In this Setup page, you can adjust the value
of the Brightness, Contrast, Hue and
Saturation for the video out. You can set
the Sharpness and the Gamma among
high, medium and low.
And you can also set the Luma Delay time
between 0T and 1T.
[Panel Quality Setup]
In this Setup page, you can adjust the value
of the Brightness, Contrast, Hue and
Saturation for the LCD screen panel. You
can set the Sharpness and the Gamma
among high, medium and low.
[Divx VOD]
Display the DivX® registration code.
17
Page 18
Tip:
Enter this DVD players DivX registration
code when you rent or purchase video from
www.divx.com/vod. The DivX videos rented
or purchased through the DivX® VOD
(Video On Demand) service can be played
only on the device to which it is registered.
Preference Setup
[Subtitle] --- Select the default subtitle
language for DVDs.
[DVD Menu] --- Select the menu language
for DVDs.
[Parental]
Restricts access to DVDs that are
unsuitable for children. These types of
DVDs must be recorded with ratings.
Note
The Preference Page onl y can be adjusted
when pressing SETUP button in DISC
STOP mode (Pressing the STOP button
twice) or no disc in the unit.
[Tv Type]
If the video does not appear correctly,
change the settings. By default, this setting
matches the most common setting for TVs
in your country.
g[Pal] – for PAL-system TV.
g[Ntsc] – for NTSC-system TV.
g[Auto] – for TV that is compatible with
both PAL and NTSC.
[Pbc]
Fr VCDs/SVCDs recorded with PBC
(Playback Control), you can access the
disc content through an interactive menu.
g[On] – an index menu is displayed when
you load a disc for play.
g[Off] – skip the menu and start play from
the first track.
[Audio] --- Select the default audio
language for DVDs.
1 Select one rating level and press ENTER .
2 When set On in Password Mode item,
you should input the password. Press the
numeric buttons (0-9) to enter the
password. (The default password is
“8888”).
Note
gThe ratings are country-dependent. To
allow all discs to play, select ‘8 Adult’.
gSome DVDs have ratings printed on them
but are not recorded with ratings. This
function has no effect on such DVDs.
[Default]
Reset all the settings of the DVD player to
factory default, except for [Parental] and
[Password] settings.
18
Page 19
Password setup
[Password Mode] --- On or off.
When you set on or off, you should input
the password (The default password is
“8888”).
[Password]
Follow the instructions to set or change the
password for locked discs and play
restricted DVDs.
1 Press the numeric buttons to enter the old
password.
2 Enter the new password then input again
to confirm the password.
3 Press ENTER to confirm.
19
Page 20
7 DISC NOTES
Handling and Cleaning
Dirt, dust, scratches and warping discs
will cause wrong operation.
Do not place stickers or make scratches
on discs.
Do not warp discs.
A disc should always be kept in its case
when not in use to prevent from
damage.
Do not place discs in the following
places:
1. Direct sunlight.
2. Dirty, dusty and damp areas.
3. Near car heaters.
4. On the seats or dashboard.
Preparing New Discs with Rough Spots
Disc Cleaning
Use a dry soft cloth to wipe the surface. If
the disc is quite dirty, using a soft cloth
slightly dip with isopropyl (rubbing)
alcohol. Never use solvents such as
benzine, thinner or conventional record
cleaners as they may mar the surface of
the disc.
Note
A disc may become somewhat scratched
(although not enough to make it
unusable) depending on the way it is
handled and conditions in the usage
environment. Note these scratches are
not an indication of any problem with the
player.
A new disc may have rough edges on
its inside and outside edges. If a disc
with rough edges is used, the proper
setting will not be performed and the
player will not play the disc. Therefore,
remove the rough edges in advance by
using a ballpoint pen or pencil as
shown on the right. To remove the
rough edges, press the side of the pen
or pencil against the inside and outside
edges of the disc.
20
Page 21
8 SPECIFICATION
Note
gSpecification and design are subject to
change without notice.
Accessories supplied
gRemote control and batteries
gAudio/video cables
Playback media
gDVD-Video, Video CD/ SVCD, Audio CD,
CD –R/CD-RW, DVD±R/RW, Picture CD,
MP3-CD, WMA-CD, U SB flash drive,
SD/MS/MMC card
USB
gCompatibility: Hi-Speed USB (2.0)
gClass support: UMS (USB Mass Storage
Class)
Audio performance
gDA converter: 24 bits, 192 KHz
gFrequency response:
gDVD: 20 Hz – 22 KHz (48 KHz);
20 Hz – 44 KHz (96 KHz)
gSVCD: 20 Hz – 20 KHz (44.1 KHz);
20 Hz – 22 KHz (48 KHz)
gCD/VCD: 20 Hz – 20 KHz (44.1 KHz);
gSignal-Noise (1 KHz): 90dB
(A-weighted)
gDistortion/noise (1 KHz): 65dB
Audio format
gAnalog sound stereo
gDolby surround compatible downmix from
Dolby Digital multi-channel sound
gMP3 (ISO 9660): 96, 112, 128, 256 kbps
& variable bit rate fs, 32, 44.1, 48 KHz
Connections
gAudio/Video output
TV standard
gNumber of lines:
g625 (PAL/50Hz); 525 (NTSC/60Hz)
gPlayback: Multi-standard (PAL/NTSC)
Video performance
gVideo output: 1 Vpp ~ 75ohm
Video format
gHorizontal resolution:
gDVD: 720 pixels (50Hz); 720 pixels
(60Hz)
gVCD: 352 pixels (50Hz); 352 pixels
(60Hz)
gVertical resolution:
gDVD: 576 lines (50Hz); 480 lines
(60Hz)
gVCD: 288 lines (50Hz); 240 lines
(60Hz)
Main unit
gDimensions (WxHxD): 190.5x155.5x38
(mm)
Power
gPower supply rating: DC IN 9V
gPower consumption: 10W
21
Page 22
9 TROUBLESHOOTING
g
control has been loaded with correct
direction.
• Replace the battery of the remote control.
Warning
gRisk of electric shock. Never
remove the casin
No Power
• Check if the power cord has been
properly connected to the power outlet.
• Check if the main power has been
switched on.
No picture
• Check if the system connection is proper
and secure.
• Check if the connection cables are
damaged.
• Clean the disc.
• Check if the TV set is in power on state,
use the remote control for TV to change
the TV channel until you see the DVD
screen.
of this unit.
The buttons on the DVD player do not
work
• Disconnect this DVD player from the
power outlet for a few minutes, then
connect again.
The contents of the USB flash drive
cannot be read
• The USB flash drive format is not
compatible with this DVD player.
• Drive is formatted with different file
system which is not supported by this
DVD player.
No sound
• Ensure that the audio cables are
connected and the connected device is
turned on to the correct input source.
• Press AUDIO button to select the other
audio tracks of disc.
• Check if the MUTE function of the TV or
Amplifier has been activated.
Cannot SKIP or SEARCH
• Some discs are programmed that do not
allow users to SKIP or SEARCH at some
sections, especially at the beginning
WARNING section.
• Single Chapter disc cannot apply SKIP
function.
Remote control does not function
• Point the remote control towards the
remote sensor on the player.
• Check if the battery of the remote
22
Page 23
1 year
Loading...