Page 1
DVD 5.1 HOME THEATER SYSTEM
DA646PA
Page 2
Contents
Features.......................................................................................2
For Your Attention...........................................................................3
Accessories...................................................................................4
Panel............................................................................................5
Connection.................................................................................6-7
System Setup...........................................................................8-12
Remote Control.......................................................................13-14
Play........................................................................................15-19
Troubleshooting...........................................................................20
Specification...............................................................................21
-1-
Page 3
Features
Thank you for purchasing our product. Please read this manual
carefully before connection and operation. Please keep this manual
for future reference.
This DVD player is a new generation home player which can produce
high quality video and audio for your continued enjoyment.
Built in Dolby Digital, LPCM, MPEG etc. digital audio decoder
HiFi, 96kHz/24bit audio digital processor
COAXIAL digital audio output
Compatible with DVD/VCD/CD/MP3/JPEG/ PICTURE
CD/MPEG4 etc.
AM/FM stereo tuning system
High quality amplifier
-2-
Page 4
For Your Attention
IMPORTANT NOTES
Please read through the manual carefully before connection and
operation.
Do not open the cover or touch any internal components.
Turnoff the power when the unit is not being used. (Unplug the
power cord if the unit is not used for a long time)
Plug,as the disconnected device entirely with power source ,should
keep in easy-to-operation in daily life.
Don't expose this unit to direct sunlight. Keep away from any
heating sources.
Don't expose this unit to rain or moisture.
Place the unit on a horizontal level. Keep the unit ventilated. Don't
block the heat hole. Overheating may cause malfunction.
Clean the cabinet with soft cloth. Detergent or alcohol is not
recommended as it may damage the unit.
This book is only a guide for user’s operation.
The apparatus shall not be exposed to dripping or splashing and
that no object filled with liquids, such as vases, shall be placed on
the apparatus.
The lightning flash is intended to alert the user to the presence
of dangerous voltage within the product's enclosure, and
touching the internal components may result in a risk of electric
shock to persons.
CAUTIONCAUTION
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CLASS 1
LASER PRODUCT
The exclamatory mark is intended to alert the user to the
presence of important operating instructions.
To reduce the risk of electric shock or fire, do not open the
cover. Refer service to qualified service personnel.
This mark indicates this unit belongs to class 1 laser product.
The laser beam may produce radiation harm to the directly
touching human body.
-3-
Page 5
Accessories
Accessories
User Manual
l
ua
n
a
m
er
Us
AM Antenna
Remote Controller
Remote control
FM Antenna
A/V Cable
Speaker Connect Cable
Remote Controller Operation
Insert the batteries into the cell box. Points the remote controller at
the remote sensor within 8 meters and with 30-degree of its left or
right side.
Take the batteries out of the controller when it is not being used for
a long time.
This unit can play the following types of discs
Disc types
DVD
Symbol Contents
Audio + Video
MP3
Video-CD
VCD
CD-DA
Picture CD
MPEG-4
COMPACT
DIGITAL VIDEO
V I D E O
-4-
VIDEO CD
Audio
Audio + Video
Audio
JPEG Photo CD
Audio + Video
Page 6
FRONT PANEL
Panel
STANDBY
1. Standby Button
2. Line2 Input
3. Headphone Jack
REAR PANEL
ON OFF
SWSW CENCEN SRSR SLSL
4 4 4 4 48
SPEAKERS OUT
FRFR FLFL
++
L1
--
R1
POWER
++
--
1. POWER SWITCH
2. SPEAKER OUTPUT TERMINALS
3. LINE1 INPUT
4. VIDEO OUTPUT
5. S-VIDEO OUTPUT
LINE2 IN HEADPHONE
4. Disc Door
5. Display Screen
6. Open/Close Button
COMPONENT VIDEO OUT
YCb/Pb
COAXIAL
Cr/Pr
VIDEO
S-VIDEO
LINE1 IN 2CH AUDIO OUT DIGITAL AUDIOVIDEO
L1 L2
R1 R2
6. L/R AUDIO OUTPUT
7. COMPONENT VIDEO OUTPUT TERMINAL
8. COAXIAL DIGITAL OUTPUT
9. FM ANTENNA JACK
10. AM ANTENNA JACK
VOLUME
7. Play/Pause
Button
8. Stop Button
9. Volume Knob
FM 75ohm -ANTENNA- AM LOOP
-5-
Page 7
Connection
++
----
++
SWSW CENCEN SRSR SLSL
FRFR FLFL
4 4 4 4 48
SPEAKERS OUT
terminals
++
----
++
SWSW CENCEN SRSR SLSL
FRFR FLFL
4 4 4 4 48
SPEAKERS OUT
terminals
R
L
Stereo Audio
audioUse a pair of cable (red for right /white for left) to connect the stereo
audio output terminal of this unit to the other stereo audio input terminal.
Coaxial Digital Audio
specifiedUse the coaxial cable to connect the coaxial output terminal of this
unit to the coaxial input terminal of power amplifier.
Speaker Output
Use the speaker cable to connect the speaker output of this unit to
peakers' corresponding terminals
the s .
Note:
The physical connection should come with audio output setup of this unit.
Please refer to Audio Setup in System Setup.
terminals
Other Audio Input
L
R
R
L
Analog Audio Output
Digital Audio Input
Digital Audio Output
COAXIAL
COAXIAL
DIGITAL AUDIO
-6-
CENTER SPEAKER
SWSW CENCEN SRSR SLSL
++
SR SPEAKER
4 4 4 4 48
SPEAKERS OUT
Speaker Output
FRFR FLFL
SL SPEAKER
FR SPEAKER
++
----
SUBWOOFER
FLSPEAKER
Page 8
Connection
Connection
Connection
Connection
Connection
Connection
Connection
Connection
Component Input
Y
Cr/PrCb/Pb
Connection
Component Input
Y
Cr/PrCb/Pb
VIDEO
Connection
Y
Cb/Pb
Component Input
Y
Cr/PrCb/Pb
The following available video output for this unit .
Composite Video
Use the AVc able (yellow terminal)to connect composite video output terminal
of this unit to the TV/monitor video input terminal.
S-Video
Use the S-video cable to connect the s-video output terminal of this unit to the
TV/monitor S-video input terminal.
Component Video (Y, Cb/Pb, Cr/Pr)
Use -core AV cable to connect the component output terminals of this unit to
3
the corresponding TV/monitor input terminals.
Note:
Real connection depends on the TV/monitor input terminal.
Don't use the all connections at the same time, otherwise the picture will be
affected.
Only the physical connection conforms to the video setting can it produce
the normal picture (please refer to the Video Setup in System Setup).
S-VIDEO
VIDEO
Component Input
Y
Cr/PrCb/Pb
VIDEO
S-VIDEO
Video and
S-Video Output
-7-
Y
Cb/Pb
Cr/Pr
Component Video
Output
Page 9
System Setup
MENU OPERATION:
Press [SETUP] key for the screen to show the setup page. In setup mode,
press [SETUP] key again to quit the setup page. Press direction key to the
desired item, and press [ENTER] to confirm.
(1) Some setup items are concerning the present modes. The items in gray
can't be set up.
(2) The setup is memorized and will be kept after the power has been turned off.
GENERAL SETUP PAGE
TV Display:
4:3 PANSCAN: When the unit connects to the normal TV set, the wide-
screen image shows on the full screen, but some part is cut off.
4:3 LETTERBOX: When the unit connects to the normal TV set, the widescreen image shows and black bars appear on the top and bottom of screen.
16:9: Use this item when the unit is connected with the wide screen TV set.
Wide-Squeeze: Use this item when the unit is connected to the wide-screen
TV set.
ANGLE MARK:
It will show the ANGLE mark when playing DVD disc with multi-angle view if
selection is ON.
OSD LANG:
Select on-screen display language.
CLOSED CAPTIONS:
This function doesn't work when the disc is without captions. If the caption is
OFF, press [SUBTITLE] key on the remote controller to turn the captions on.
SCREEN SAVER:
If the SCREEN SAVER is set ON and the unit is switched on without a disc
playing for several minutes, a moving picture appears on the screen and the
unit will go to standby mode after 20 minutes. You can press the [STANDBY]
key on the remote controller to activate.
LAST MEMORY:
When this function is ON, the unit can memorize the time elapsed from the
last time you played the disc. When playing next time, it will resume playing
from the memorized time.
AUDIO SETUP PAGE
ANALOG AUDIO SETUP:
DOWNMIX:
LT/RT: The audio out is Left and Right channel formatting even if the original
sound is 5.1CH format.
-8-
Page 10
System Setup
STEREO: The audio out format is stereo even if the original sound is 5.1CH
format.
3D SURROUND: The audio out is virtual surround sounds
5.1CH: Turn off DOWNMIX function. If playing 5.1CH discs or the unit is
connected with 5.1 channel amplifier, this item should be selected.
FRONT, CENTER, REAR and SUB-WOOFER SPEAKER:
If your speaker system includes the above speakers, you can set these
items according the real speaker status.
DIALOG: The DIALOG mode is available, and you can press up and down
direction key to adjust it. (In the DOWNMIX mode, LT/RT or STEREO is
selected.)
D.R.C: The D.R.C can control data record. You can chose AUTO, ON and
OFF in this mode.
DIGITAL AUDIO SETUP PAGE
DIGITAL OUTPUT:
SPDIF OFF: No digital output(coaxial off), only analog audio output.
ALL: If this item is selected, you can set up RAW.
PCM ONLY: The digital audio signal output will be in PCM format.
LPCM OUT :
When DIGITAL OUTPUT is set to PCM ONLY, this item is available.
Select PCM frequency at 48kHz or 96kHz.
Note: Some amplifiers don't support 96kHz sampling which will effect the
coaxial output.
DOLBY DIGITAL SETUP
DUAL MONO:
Stereo: Set audio output to the stereo output.
L-mono: Set audio output to the mono-left channel.
R-mono: Set audio output to the mono-right channel.
Mix-mono: Set audio output to the mix-mono channel.
DYNAMIC:
Select this to reduce the overall volume and still keep defined audio sound.
You can press up and down direction key to adjust it.
-9-
Page 11
System Setup
CHANNEL DELAY PAGE:
If the above setup dissatisfy you, you can set the speaker distances in the
real conditions. Press up/down direction key to select the speaker, and
press left/right direction key to adjust the distance.
EQUALIZER:
In this item you can set sound mode, bass boost, super bass and treble
boost. You can select one according to your preference and the disc
content.
3D PROCESSING:
In PROLOGIC ON mode, the reverb mode setup is available.
HDCD SETUP:
You can select the digital filter at off,1x and 2x.
-10-
Page 12
System Setup
VIDEO SETUP PAGE
COMPONENT V IDEO:
OFF: Set video output to the composite.
YUV: Set video output in analog component video format when connecting
to Y/U/V terminals.
P-YUV: Set progressive YUV signals. Connection same as YUV.
Note::
If the video setting differs with the physical connection, the TV set may not
have picture. In this case, you can RESET the machine, then keep pressing
key [V_MODE] until the picture returns again.
COLOR SETTING SETUP:
COLOR SETTING includes: SHARPNESS, BRIGHTNESS, CONTRAST,
GAMMA, HUE, SATURATION and LUMA DELAY .
Adjust each item in the Color Setting to get the suitable color output of the
TV screen.
SHARPNESS: There are three optional output modes:
HIGH\MEDIUM\LOW.
BRIGHTNESS: Use the left/right direction key to move the scroll and adjust
the brightness.
CONTRAST: Use the left/right direction key to move the scroll and adjust
the contrast.
GAMMA: There are four optional output modes:
HIGH\MEDIUM\LOW\NONE.
HUE: Use the left/right direction key to move the scroll and adjust the hue.
SATURATION : Use the left/right direction key to move the scroll and adjust
the saturation.
LUMA DELAY: In this item you can choose 0T or 1T .
-11-
Page 13
System Setup
PREFERENCE PAGE
TV TYPE:
This unit is suitable for all kinds of TV systems. You can select one of the
PAL, MULTI or NTSC.
PAL : Set the output at PAL system.
MULTI: The TV system is auto switched according to the disc system.
NTSC: Set the output at NTSC system.
NOTE: If a wrong selection is made, the viewing image will be very poor. In
such case, you are supposed to change the option in this item to fix the error.
PBC: There are 2 optional output modes: ON/OFF. If the PBC is set on,
when playing VCD, return to the main menu. If the PBC is set off, when
playing VCD, return to the main sequence.
AUDIO, SUBTITLE and DISC MENU LANGUAGE PAGE:
These are the initial settings by your preference. If a setting is supported by
disc content, it will work. Otherwise the disc default value works. These
settings can be changed respectively by pressing key [AUDIO] and
[SUBTITLE] when playing.
PARENTAL:
The control level is for parents to control the content and protect children
from violence and erotism. The level of the disc is higher than the setting
level and can not be played .
DEFAULT:
Reset to the initial factory setting.
PASSWORD PAGE:
Change the password. The initial factory password is 136900. You can set
your own password. If you forget your own password, you can use 136900
as general password to decode.
-12-
Page 14
Remote control
Remote Control Operation
Install the batteries into the remote control. Point the remote control at the
remote sensor on the front panel. The remote control works within about 8
metres from the sensor and within an angle of about 30 degrees from the left
and right side.
Take out of the batteries when it is not being used for a long time.
Don't expose the sensor in direct sunlight.
Battery Installation
Remove the battery
1
compartment cover on the
back of the remote control.
Insert two AAA/1.5V batteries
2
into the battery compartment
following the indications (+, -)
inside the compartment.
Replace the cover.
3
Not e:
Do not mix the old and new batteries or different types of batteries.
Weak batteries can leak and severely damage the remote control.
-13-
Page 15
Remote control
1
2
3
4
5
6
7
8
9
10
11
12
13
14
¿ì ÍË ¿ì½ø
È·ÈÏ
ѡʱ
Çú
ÇúÇú
ÉùµÀ
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
1
STANDBY
2
NUMBERS
FAST FORWARD
3
/BACKWARD(SEARCH)
4
PLAY/PAUSE
5
STOP
6
TITLE(AM/FM)
7
DIRECTION KEY
8
AUDIO(MEMORY)
9
ANGLE
10
A-MODE
11
REPEAT
12
PROG
13
S.EFFECT
14
CH-LEVEL
15
SETUP
16
OPEN/CLOSE
17
A-B
18
OSD
19
VOLUME+/-
20
GOTO
21
NEXT/PREVIOUS
(RADIO)
-14-
22
MUTE
23
SUBTITLE(AUTO)
24
ENTER
25
MENU(MO/ST)
26
V-MODE
27
L/R/ST
28
SOURCE SELECT
29
STEP
30
ZOOM
31
TONE
Page 16
Play
STANDBY
OPEN/CLOSE
GOTO
VOLUME
Stand by/working mode switch
Eject or load the disc tray
The digit keys can be used to input the corresponding numbers.
After the unit loading a VCD1.1 or CD disc, the digit keys can be
used to select a track directly. Press [10+] and then another digit
key to select the tracks whose number are more than 10.
Press [GOTO] to select title time, chapter time or track time to play.
You can use digital key input the GOTO time.
When playing the disc, press[ ]button once to pause. Press[ ]button
again to return to normal play.
Press[ ]button, no sound will give out. Press[ ]again, MUTE OFF
will display and the sound will resume.
Press this button for quick forward search.
Press this button for quick rewind search.
Press [VOLUME+] to adjust volume up.
Press [VOLUME-] to adjust volume down.
TITLE
SUBTITLE
AUDIO
When playing DVD disc, press it to the previous chapter.
When playing VCD or CD disc, press it to the previous track.
When playing DVD disc, press it to the next chapter.
When playing VCD and CD disc, press it to the next track.
Note: When playing Mp3 disc, you must select the song by up or
down direction key, then press[ ENTER] to play. If you press left
direction key, the system will return to superior root directory.
Return to the top menu when playing DVD disc.
When playing the disc with multi-subtitle, press [SUBTITLE]
continually to select the desired sub-title.
Select the desired audio channel when playing DVD disc.
-15-
Page 17
Play
MENU
A-MODE
ANGLE
V-MODE
PROGRAM
OSD
SOURCE
SELECT
S.EFFECT
CH-LEVEL
TONE
Return to the previous menu when playing DVD disc.
W hen playing VCD2.0 disc, it works as PBC. Press [MENU] button
to switch PBC ON and PBC OFF. under PBC ON mode, the disc
menu will show. You can select a program in the menu. Under PBC
OFF mode, the menu will not appear, press digital key to select the
track directly. VCD1.1, CD-DA and Mp3 have no PBC menu.
Audio output switch.
When playing the disc with multi-angle, it's convenient to change the
view angle.
Video output mode switch (if losing pictures or picture is abnormal,
keep switching until you reach a clear picture.)
If the disc is with 2 or more tracks, chapters or titles, set up the
playing order as your preference. Press this button to enter program
menu.
Press digital key to input the number of the track, title or chapter. If
the programmed tracks are over ten, press [NEXT] to go on
programming. (Maximum 20 programable items)
Use the direction key to move the cursor to the START. Press
[ENTER] to start PROGRAM play.
When playing MP3 disc, NO program function! Press [PROGRAM]
button once to enter directory-play mode, you can select program to
play in the current directory, and press [PROGRAM] again to enter
file-list mode, you can select program to play in the file list of whole
disc .
Press the [OSD] button, the relative information of the disc will
display on the TV screen.
Source switch among DVD/TUNER(AM/FM)/LINE1/LINE2
Press [S.EFFECT] button to obtain different sound effect. CD
playing is more proper to obtain better sound effect. You had better
close S.EFFECT when playing disc with Dolby 5.1 channel in order
to obtain real 5.1 effect.
Press this key to select a channel then press [VOLUME+/-] to adjust
its level.
Press [TONE], then press [VOLUME+/-] to control bass and treble.
-16-
Page 18
Play
L/R/ST
STEP
ZOOM
REPEAT
A-B
SETUP
When playing VCD or CD disc with multi-channel, press [L/R/ST]
button to select left channel/right channel/stereo/mix audio output.
When playing DVD, VCD or SVCD disc, press [STEP] once, the
picture changes to next frame. Press [ ] to resume normal play.
When playing DVD, VCD disc, press [ZOOM] to zoom in or zoom out
the picture.
In zoom in mode, press direction key to move the picture for viewing.
The picture can not be moved in zoom out mode.
Press [REPEAT] button to repeat a title, chapter, track or the whole
disc.
When playing DVD disc, press [REPEAT] button continually, the turn
is chapter repeat, title repeat and all repeat.
When playing VCD or CD disc, the turn is track repeat and all repeat.
When playing MP3 disc, the turn is single repeat, repeat one, repeat
folder and folder.
When playing DVD, VCD, CD disc, press [A-B] button to repeat a
certain contents.
Press [A-B] key on the start point (A) and the ending point (B) to
select the repeat part.
Press [A-B] the third time, cancel A-B repeat and return to normal
play.
When playing DVD, VCD or CD disc, press [ ]button once, the unit
will memorize the previous ending point. Press[ ]button to go on
the play. Press[ ]button for the second time to stop the play and
end memory.
Press it once to enter setup menu, press it again to exit.
ENTER
Press it to confirm a selected item.
-17-
Page 19
Play
PLAY PICTURE CD DISC
Press [ ] key, 12 small pictures will show on the TV screen.
Press [ ]/[ ]/[ ]/[ ] key to select the desired picture.
Press [ ]/[ ]/[ ]/[ ]key to select Slide Show, then press [ENTER] to play
randomly.
Press [ ]/[ ]/[ ]/[ ]key to select Menu, then press [ENTER] to enter Remote
Controller Function menu.
Remote Controller Function menu as follows:
[ ]: to enter picture preview mode; [ ]: to view previous picture; [ ]: to
view next picture; [ ]: to play picture; [ ]: to rotate 90-degree
anticlockwise; [ ]: to rotate 90-degree clockwise; [ZOOM]: change zoom
mode; [ ]: to zoom in the picture; [ ]: to zoom out the picture; [ / / / ]:
pan in zoom mode . Select CONTINUE to exit.
LINE INPUT OPERATION:
This unit has two groups of extra audio input terminals, i.e. LINE1 and
LINE2 input. You can input the analogue stereo audio signals from extra
devices such as VCD, CD, VCR, MP3 player, etc through the extra audio
input terminals.
After the connections have been correctly made, press [SOURCE SELECT]
to switch to the corresponding signal source to enjoy the audio from the
connected extra device.
PLAY MP3:
When playing a MP3 disc, there is a menu screen on TV, press the [ ]or[ ]
button to shift the cursor to select the track or folder, and press the [ENTER]
button to play the selected track or folder (it needs to enter the sub-folder to
select the track and press the [ENTER] button to play for some MP3 discs).
Also use the digit buttons in the remote controller to select the track.
There are two play modes for MP3 disc: folder and file play, the default
mode is the folder play; press [PROG] button to switch the mode.
-18-
Page 20
Tuner Operation:
AM/FM
MO/ST
MEMORY
AUTO
SEARCH+
SEARCH-
RADIO+
AM/FM switch.
Mono/Stereo switch in FM mode.
After having selected a station and tuned a new frequency, press
[MEMORY] to save the frequency.
Automatic searching and presetting in FM/AM tuner mode.
Press the digital button to choose a preset station, you must input
two digital key to select a station. For example, if you select 02
station, you must press[0] and [2] .
if you select the 15 station, you must press [1] and[ 5].
Searching with frequency up.
Searching with frequency down.
Skip forward a station.
Play
RADIO-
Skip backward a station.
Under Tuner mode, you can press [A_MODE] to change the stereo
input to 5.1CH output. At the same time, [VOLUME+/-], [CH_LEVEL],
[MUTE],[TONE] and [S.EFFECT] buttons are available, please refer
to the PLAY chapter for details.
-19-
Page 21
Trouble shooting
Symptom Cause(s) Remedy
No Power
The AC power cord is not connected
to the power supply or is not
connected to a power supply securely.
Please check that the AC power
cord is connected securely.
Picture
There is no
picture or the
picture is
distorted.
Sound
There is no
sound or the
sound is
distorted.
Unable to
play a disc
The buttons
on the unit
doesn't work.
The remote
control does
not function.
Video input mode of the connected
TV isn't correctly set.
Video output mode isn't correctly set.
The video cable isn't connected
securely.
The audio cables aren't connected
securely.
The volume is set at the lowest level.
The sound is switched off.
The disc is in fast forward/rewind
playback.
This disc is placed in the disc tray
in a wrong way.
The rating of the disc is higher than
the rate set in the parental control
item.
The unit isn't compatible with the
disc.
The disc is dirty.
The unit is being interfered with
static electricity etc.
There is no battery in remote
control.
The batteries are out of charge.
The remote control isn't pointed to
the remote sensor.
The remote control is out of its
working area.
The unit is shut down.
Set an appropriate video output
mode.
Press [V-MODE] repeatedly
until the picture becomes normal
again.
Connect the video cable
securely.
Connect the audio cables
securely.
Turn up the volume.
Press [MUTE] on the remote
control to switch on the sound.
Press [PLAY/PAUSE].
Check that the disc is placed in
the disc tray with its label side
upwards.
Reset the settings in the
parental control item.
/
Clean the disc.
Switch off and unplug the unit.
Then connect the unit to the AC
supply and switch it on again.
Install two AAA/1.5V batteries
in it.
Replace the batteries with new
ones.
Make sure that the remote
control is pointed to the remote
sensor.
Make sure the remote control is
within the working area.
Switch off the unit and disconnect it from
the AC outlet. Then power on the unit again.
-20-
Page 22
DVD RECEIVER
Specification
Power supply
Power consumption
Working
environment
Disc output
Tuner
Temperature -10~+40
Relative humidity
TV System
Frequency Range
S/N(A weight)
Dynamic Range
THD+NOISE
WOW FLUTTER
AM frequency Range
FM band Range
Power output (Max)
Frequency response
AC ~240V/50Hz
150W
5%~90%
PAL/NTSC
20Hz~20KHz
80dB( )1KHz
70dB( )1KHz
-60dB(1KHz)
Below the limit of apparatus measure
522KHz~1620KHz
87.5MHz~108MHz
15WX5+30W
1.5dB(20Hz~20KHz)
This product incorporates copyright protection technology that is
protected by U.S. patents and other intellectual property rights. Use of
this copyright protection technology must be authorized by Macrovision,
and is intended for home and other limited viewing uses only unless
otherwise authorized by Macrovision. Reverse engineering or
disassembly is prohibited.
-21-
Loading...