Avycon AVR-HT808A-10T, AVR-HT808A-12T, AVR-HT808A-16T, AVR-HT808A-1T, AVR-HT808A-20T Quick Start Guide

...

All-in-One DVR

Quick Start Guide

Note: Please read this instruction carefully for correct use of the product and preserve it for reference purposes. All the examples and pictures used here are for reference only. There may be several technically incorrect places or printing errors in this manual. The updates will be added into the new version of this manual. The contents of this manual are subject to change without notice.This device should be operated only from the type of power source indicatedon the marking label. The voltage of the power must be veriﬁed before using the same.

1. HDD Installation

This series of the product supports 1 SATA hard drive. Please make sure that the device is powered off before the installation. The pictures of the installation are only for reference, please take the real object as the standard.

1.Loosen the screws to open the cover.

3.Place the HDD onto the bottom of the machine.

5. Turn over the machine and secure the HDD with the screws.

2. Rear Panel Installation

AL A R M O U T

AL A R M I N

1 5

CO M1

GND

NO1

GND

CO M2

NO2

3 7

531

2 6

4 8

AU DI O I N

2.Screw the screws into the HDD but not tighten them.

4.Connect the power and data cables.

6. Install back the cover and secure it with the screws.

CV B S

125

6 8

AU DI O O U T

VI DE O I N

Rea r Panel f or 8CH

e S A TA

R S

485

US B

LA N

VG A

Rea r Panel f or 16CH

Nam e

ALA RM OUT

ALA RM IN

GND

AUD IO IN

VID EO IN

CVB S

AUD IO OUT

HDM I

VGA

LAN

USB

e-S ATA

RS4 85

DC1 2V

Rel ay outp ut; con nect to e xtern al alar m

Ala rm inpu t for con necti ng sens or

Gro und

Aud io inpu t

Vide o inp ut

CVB S outpu t

Aud io outp ut

Con nect to h igh def initi on disp lay dev ice

Con nect to m onito r

Eth ernet c onnec tor

Con necto r for USB d evice s

Con necto r for e-S ATA

Con nect

Pow er inpu t

3. Startup & Shutdown

• Startup

1. Connect the monitor and the power.

2. The device will boot and the power indicator will display blue.

3. A wizard window will pop up.

• Shutdown

Go to “Main Menu” and then select “Shutdown” icon. This will bring up a shutdown window. The device will shut down by clicking “OK” button. Then disconnect the power.

4. Login

For our HT800A series DVRs, the default username is admin and the default password is 123456. When starting HT800A series DVR for

the ﬁrst time, you will see a prompt to begin a startup wizard. You can skip this wizard if you would like, but it will help you conﬁgure basic settings for your DVR. The wizard may allow you to also change the default password for better security. If you decide to skip the wizard, to access the live view and start using your DVR click on the Start button in the bottom left of the menu bar on the bottom of the screen and then click on Login and enter in the default password.

User name

Passw ord

DC 12 V

Des cript ion

for

RS4 85 devi ces

. A is TX +,B is T X-

The interfaces of the rear panels are for reference only.

adm in

Enter Password

Display Password Log InAutomatically

Edit SecurityQuestion Login Cancel

Intern et

5. Analog Camera Connection

First connect the camera to the DVR. Then go to Start → Settings → Camera → Manage Camera → Signal Access Set to checkmark

the video mode. The actual signals input shall correspond to the video mode. Please refer to User Manual for details.

6. Network Configuration & Add IP Camera

After you ﬁnish adding IP cameras, you can see the live images through the monitor of the DVR. The following will mainly introduce how to add the IP cameras via LAN/WAN.

• LAN

1.Set the network of the DVR. Go to Start → Settings → Network →TCP/IPv4. Input IP address, subnet mask, gateway, etc. If using

DHCP, please enable DHCP in both the DVR and the router.

2. Go to Start → Settings → Network → Port. Input HTTP port (the default value is 80), server port (the default port is 6036).

3. Click “Apply” to save the settings.

TCP /IPv4

Por t

DDN S

IP Add ress Se tting s

Eth ernet Po rt 1 ( Onli ne )

Obta in an IP ad dress a utoma tical ly

IP Addr ess

Subn et Mask

Gate way

Obat in DNS se rver ad dress a utoma tical ly

Pref erred D NS

Alte rnate D NS

192 . 16 8 . 1 . 2

0 . 0 . 0 . 0

192 . 16 8 . 1 . 1

0 . 0 . 0 . 0

4. Go to Start → Settings → Camera → Add Camera. The DVR will automatically refresh the cameras searched. The IPC which supports the Onvif protocol may be added manually. If the IPC searched is not in the same local network as the DVR, you should select the device and click to modify the IP address.

Qui ckly Ad d

Man ually A dd

No.

IP Addr ess

192 .168. 2.45

Sel ected : 1/1

Rema in Band width : 10 / 10 Mb

Mac Add ress

IP Ad dres s

Sub net Mask

Gat eway

Use rnam e

Pas swor d

UPn P Net work St atus

E-m ail

Edi tPor t

NAT

Add C amera

Sub net Mas k

255 .255. 255.0

Def ault Pa sswor d

Edit IP

CE :9 8 :23 :7 5 :35 :22

192 .16 8 . 1 . 45

255 . 255 . 255 . 0

192 .16 8 . 1 . 1

adm in

OK Cancel

Pro tocol Mod el

XXXXXX

Add

Vers ion

4.0 .0.1. beta1

Can cel

5. Checkmark the device you want to add and then click “Add” button. The DVR will automatically refresh the cameras and return to “Edit Camera” interface. “Online” status means connecting the device successfully and you will see the live image. You may select the added device and click button to modify channel, IP address, ect.

No. Cam era Nam e

[A01 ]Came ra1

[A02 ]Came ra2

[A03 ]Came ra3

[A04 ]Came ra4

Edi t Camer a

IP Addr ess

192. 168.1 .45IP Cam era 1

Camera Name

IP Address

Port

Protocol

Model

Username

Password

Port

Edi t Camer a GroupSig nal Acce ss Set

Stat us

Onli ne

Edit Camera

IP Camera 1

192 .168 . 1 . 58

XXX

admin

Prot ocol Model

XXX

Display Password

Test OK

Sea rch Cam era

XXX

Prev iew

Canc el

Dele teEdit

• WAN

1.Set the network of the DVR. Go to Start → Settings → Network → TCP/IPv4. Input static IP address or enable PPPoE and then input the user name and password received from your ISP. 2. Go to Start → Settings → Camera. Click “Add Camera” or behind the column of the search camera and select “Manually Add” to add the IP cameras. Input IP address, server port, username and password of the IP camera. The IP camera must be connected over WAN. And here the IP address of the IP camera must be a WAN IP address.

7. UPnP

You can use the UPnP function to enable the fast connection of the

1. Go to Start → Settings → Network → UPnP, and enable UPnP and then click “Apply” button to save.

2.Enable the UPnP function in the router.

3.Click “Refresh” button to refresh the UPnP status. If the UPnP

status were still “Invalid UPnP” after refreshing it for several times, the port would be wrong. Please change the mapping type to “Manual” and then click to modify the port until the UPnP status turns to “valid UPnP”.

TCP/IPv4 Port DDNS E-mail UPnP NAT NetworkStatus

UPnP

Enable

MapType Auto

Port

Port Type External Port External Address

HTTP Port 80 183.17.254.19 80 Valid UPnP

6036

Server Port

RTSP Port 554 554 Invalid UPnP

183.17.254.19 6036 Valid UPnP

UPnP Status Edit

Refresh Apply

8. NAT

• NAT Setting

1. The DVR shall be powered on and connected to the network.

2. Go to Start → Settings → Network → TCP/IPv4. You can obtain

the IP address, subnet mask and gateway automatically. You can also manually enter them according to the actual network situation. Please make sure the network segment is the same as that of the network which is used.

3. Set the preferred or alternative DNS Server. Click “Apply” to save the parameters.

4. Go to Start → Settings → Network → NAT tab. Enable NAT and select the NAT Server (The default NAT Server is avyconp2p.com). Click “Apply” to save the parameters.

TCP /IPv4

Por t UPn P N AT

NAT

Ena ble

NAT Se rve r

• NAT Access

After ﬁnishing the NAT settings, you can input www.avyconp2p.com in the IE address bar and then press enter to go to the following interface. If you are the ﬁrst time to access the NAT, you shall download and install the ActiveX according to the popup tips. After installing ActiveX successfully, it will pop the login box.

E-m ail Net work St atus

DDN S

avyconp2p.com

Enter d ev ic e seria l nu mb er

Enter U se rn ame

Enter P as sw ord

Appl y

Device Serial Number: Click on the menu bar at the bottom of the live interface to check the serial number or go to Start → Settings → Network →Network Status to check the serial number of the DVR).

Username: The username of the DVR. The default username is admin. Password: The password of the DVR. The password is set by yourself

when you conﬁgure the wizard for the ﬁrst time.

9. Manual Recording

Before recording, please install and format a HDD. In the live interface you can see the menu toolbar. Click button to start recording. Click it again to stop recording. You can also click to check the status of the recording.

10. Playback

• Instant Playback

Click “Instant Playback” in the right-click menu of the camera’s preview window to select or drag the playback progress bar to change the playback time to play back the record.

• General Playback

Click on the tool bar at the bottom of the live preview interface or click Start → Playback to go to the playback interface as shown below. You can also add the playback cameras manually. Click in the playback window to pop up the “Add Camera” window. Check the cameras in the window and then click “Add” to add playback camera. The record ﬁles of the added playback camera will be played in the playback interface.