Avycon AVR-HN532P16-56T, AVR-HN532P16-64T, AVR-HN532P16-FD-10T, AVR-HN532P16-FD-12T, AVR-HN532P16-FD-16T Quick Start Guide

...

3. Rear Panel Installation

After you ﬁnish adding IP cameras, you can see the live images through the monitor of the NVR. The following will mainly introduce how to add the IP cameras via LAN/WAN.

Network Video Recorder

Quick Start Guide

Note: Please read this instruction carefully for correct use of the product and preserve it for reference purposes. All the examples and pictures used here are for reference only. There may be several technically incorrect places or printing errors in this manual. The updates will be added into the new version of this manual. The contents of this manual are subject to change without notice.This device should be operated only from the type of power source indicatedon the marking label. The voltage of the power must be veriﬁed before using the same.

1. Packing Check

Please check the device and the accessories after getting the device. If there are any damages, shortages or defects, please contact your dealer immediately.

2. HDD Installation

This series of the product supports 8 SATA hard drives. Please make sure that the device is powered off before the installation.

1.Remove the cover and loosen the screws to take out two mounting bars.

2.Screw the shorter pillar attached with the NVR into the bottom of the device.

3. Install back the lower mounting bar and tighten the screws of the lower HDD.

4. Connect the power and data cables and install the other three HDDs according to above-mentioned method.

5. Screw the longer pillar into the lower mounting bar.

6.Install back the upper mounting bar and tighten the screw of the pillar.

7. Install the upper four HDDs and install back the cover.

Po E P ort s

123456789101112131415

HD MI

e-S A TA

RS 4 85

GND

US B

VG A

LA N

Interne t

AL A R M O U T

K/BP/Z A BY Z

GNDGND

AL A R M I N

6 8 1091211141316

AU DI O O UT

AU DI O

I N

NO1

NO O 2

COM1C

COM O

The interfaces of the rear panel are for reference only.

4. Startup & Shutdown

• Startup

1. Connect the monitor and the power.

2. The device will boot and the power indicator will display blue.

3. A wizard window will pop up.

• Shutdown

Go to “Main Menu” and then select “Shutdown” icon. This will bring up a shutdown window. The device will shut down by clicking “OK” button. Then disconnect the power.

4. Login

For our HN500 series NVRs, the default username is admin and the default password is 123456. When starting HN500 series NVR for

the ﬁrst time, you will see a prompt to begin a startup wizard. You can skip this wizard if you would like, but it will help you conﬁgure basic settings for your NVR. The wizard may allow you to also change the default password for better security. If you decide to skip the wizard, to access the live view and start using your NVR click on the Start button in the bottom left of the menu bar on the bottom of the screen and then click on Login and enter in the default password.

Use rname

Pas sword

adm in

Ent er Pass word

Dis play Pa sswor d Log I n Aut omati cally

Log inEdi t Secur ity Que stion Can cel

5. Network Configuration

After you ﬁnish adding IP cameras, you can see the live images through the monitor of the NVR. The following will mainly introduce how to add the IP cameras via LAN/WAN. This NVR has two network ports, you can select the network work pattern as required. Network fault tolerance and multiple address setting are optional.

• LAN

1. Set the network of the NVR. Go to Start → Settings → Network → TCP/IPv4. Input IP address, subnet mask, gateway, etc. If using DHCP, please enable DHCP in both the NVR and the router.

2. Go to Start → Settings → Network → Port. Input HTTP port (the default value is 80), server port (the default port is 6036).

3. Click “Apply” to save the settings.

TCP /IPv4

Por t

DDN S

IP Addr ess Set tings

Work Pa ttern

Netwo rk Faul t Toleran ce

Obtai n an IP add ress au tomat icall y

IP Addre ss

Subne t Mask

Gatew ay

Prima ry Card

Ether net Por t 1

Ethe rnet Por t 1 ( Onlin e )

MAC Add ress

Obati n DNS aut omati cally

Prefe rred DN S

Alter nate DN S

4. Go to Start → Settings → Camera → Add Camera. The NVR will automatically refresh the cameras searched. The IPC which supports the Onvif protocol may be added manually. If the IPC searched is not in the same local network as the NVR, you should select the device and click to modify the IP address.

Qui ckly Ad d

Man ually A dd

No.

IP Addr ess

No.

IP Addr ess

No.

IP Addr ess

No.

IP Addr ess

192. 168.1 .20

192. 168.1 .38

192. 168.2 .45

Sele cted: 1 /3

Rema in Band width : 108 / 120 M b

UPn P Telne t

E-m ail

192 . 168 . 1 . 2

0 . 0 . 0 . 0

192 . 168 . 1 . 1

00：18：AE：3 5：64：1A

192 . 168 . 1 . 1

0 . 0 . 0 . 0

EditPort

80 80

Edi t IP Came ra

Mac Add ress

IP Addr ess

Subn et Mask

Gate way

Port

User name

Pass word

Edi t IP Came ra

NAT

Ethe rnet Por t 2 ( Onlin e )

MAC Add ress

Add C amera

Subn et Mask

255. 255.2 55.0

Defa ult Pas sword

CE :98 : 23 :75 :3 5 :22

192 .1 68 . 1 . 45

255 . 25 5 . 255 . 0

192 .1 68 . 1 . 1

admi n

OK Can cel

00：18：AE：3 5：64：1B

Prot ocol Mode l

Prot ocol Mode l XXX80

XXX

XXX80

XXX

XXX80

XXX

XXX80

XXX XXX

XXX

4.0. 0.1.b eta1

XXXXXX

4.0. 0.1.b eta1

XXXXXX

4.0. 0.1.b eta1

XXXXXX

4.0. 0.1.b eta1

XXXXXX

Add

Versi on

3.4. 2

Canc el

5. Checkmark the device you want to add and then click “Add” button. The NVR will automatically refresh the cameras and return to “Edit Camera” interface. “Online” status means connecting the device successfully and you will see the live image. You may select the added device and click button to modify channel, IP address, ect.

Edi t Camer a

Rema in Band width : 85 / 120 Mb

No. Came ra Name

Edi t Camer a Group

IP Addre ss

192. 168.1 .20IP Came ra 1

192. 168.1 .38IP Came ra 2

192. 168.1 .45IP Camer a 3

Sear ch Came ra

Prot ocol Mode l

Stat us

Port

Onli ne

XXX

XXX80

Prev iew

XXX

XXXOfflin e

XXXOnli ne XXX80

Dele teEdit

You may select the added device and click button to modify channel, IP address, etc.

Edi t Camer a

Cam era Nam e

IP Addr ess

Por t

Pro tocol

Mod el

Use rname

Pas sword

IP Cam era 3

192 . 168 . 1 . 58

XXX

adm in

Dis play Pa sswor d

OKTest Can cel

• WAN

1. Set the network of the NVR. Go to Start → Settings → Network → TCP/IPv4. Input static IP address or enable PPPoE and then input the user name and password received from your ISP.

2. Go to Start → Settings → Camera. Click “Add Camera” or behind the column of the search camera and select “Manually Add” to add the IP cameras. Input IP address, server port, username and password of the IP camera. The IP camera must be connected over WAN. And here the IP address of the IP camera must be a WAN IP address.

6. UPnP

You can use the UPnP function to enable the fast connection of the device to WAN via a router without port mapping.

1. Go to Start → Settings → Network → UPnP, and enable UPnP and then click “Apply” button to save.

2. Enable the UPnP function in the router.

3. Click “Refresh” button to refresh the UPnP status. If the UPnP status were still “Invalid UPnP” after refreshing it for several times, the port would be wrong. Please change the mapping type to “Manual” and then click to modify the port until the UPnP status turns to “valid UPnP”.

TCP /IPv4

Por t UPn P

UPn P

Enab le

AutoMap Typ e

Exte rnal Po rt

Port Ty pe

HTTP P ort

6036

Serv er Port

554

RTSP P ort

E-m ail NAT Teln et

DDN S

Exte rnal Add ress

Port

UPnP S tatus Edit

80183. 17.25 4.19 Valid U PnP

Valid U PnP

6036183. 17.25 4.19

Inva lid UPn P

554

Refr esh Appl y

7. NAT

• NAT Setting

1. The NVR shall be powered on and connected to the network.

2. Go to Start → Settings → Network → TCP/IPv4. You can obtain the IP address, subnet mask and gateway automatically. You can also manually enter them according to the actual network situation. Please make sure the network segment is the same as that of the network which is used.

3. Set the preferred or alternative DNS Server. Click “Apply” to save the parameters.

4. Go to Start → Settings → Network → NAT tab. Enable NAT and select the NAT Server Address (The default NAT Server Address is nat.autonat.com). Click “Apply” to save the parameters.

TCP /IPv4

Por t UPn P NAT

NAT

Vis it Addre ss www. auton at.co m

Ena ble

NAT Ser ver Addr ess

• NAT Access

After ﬁnishing the NAT settings, you can input www.autonat.com in the IE address bar and then press enter to go to the following interface. If you are the ﬁrst time to access the NAT, you shall download and install the ActiveX according to the popup tips. After installing ActiveX successfully, it will pop the login box.

E-m ail Telne t

DDN S

nat .auto nat.c om

Appl y

Enter device ser ia l nu mb er

Enter Username

Enter Password

Logi n

Device Serial Number: Click on the menu bar at the bottom of the live interface to check the serial number or go to Start → Settings → Network →Network Status to check the serial number of the DVR).

Username: The username of the NVR. The default username is admin. Password: The password of the NVR. The password is set by yourself

when you conﬁgure the wizard for the ﬁrst time.

9. Manual Recording

Before recording, please install and format a HDD. In the live interface you can see the menu toolbar. Click button to start recording. Click it again to stop recording. You can also click to check the status of the recording.

10. Playback

• Instant Playback

Click “Instant Playback” in the right-click menu of the camera’s preview window to select or drag the playback progress bar to change the playback time to play back the record.

• General Playback

Click on the tool bar at the bottom of the live preview interface or click Start → Playback to go to the playback interface as shown below. You can also add the playback cameras manually. Click in the playback window to pop up the “Add Camera” window. Check the cameras in the window and then click “Add” to add playback camera. The record ﬁles of the added playback camera will be played in the playback interface.