Avycon AVR-HN5128E2N-FD-10T, AVR-HN5128E2N-FD-112T, AVR-HN5128E2N-FD-120T, AVR-HN5128E2N-FD-12T, AVR-HN5128E2N-FD-132T User Manual

...

Avycon AVR-HN5128E2N-FD-10T, AVR-HN5128E2N-FD-112T, AVR-HN5128E2N-FD-120T, AVR-HN5128E2N-FD-12T, AVR-HN5128E2N-FD-132T, AVR-HN5128E2N-FD-144T, AVR-HN5128E2N-FD-156T, AVR-HN5128E2N-FD-168T, AVR-HN5128E2N-FD-16T, AVR-HN5128E2N-FD-180T, AVR-HN5128E2N-FD-192T, AVR-HN5128E2N-FD-1T, AVR-HN5128E2N-FD-20T, AVR-HN5128E2N-FD-24T, AVR-HN5128E2N-FD-2T, AVR-HN5128E2N-FD-30T, AVR-HN5128E2N-FD-32T, AVR-HN5128E2N-FD-36T, AVR-HN5128E2N-FD-3T, AVR-HN5128E2N-FD-40T, AVR-HN5128E2N-FD-48T, AVR-HN5128E2N-FD-4T, AVR-HN5128E2N-FD-56T, AVR-HN5128E2N-FD-60T, AVR-HN5128E2N-FD-64T, AVR-HN5128E2N-FD-6T, AVR-HN5128E2N-FD-70T, AVR-HN5128E2N-FD-80T, AVR-HN5128E2N-FD-8T, AVR-HN5128E2N-FD-96T, AVR-HN5128E2N-FD, AVR-HN516P16-10T, AVR-HN516P16-12T, AVR-HN516P16-16T, AVR-HN516P16-1T, AVR-HN516P16-20T, AVR-HN516P16-24T, AVR-HN516P16-2T, AVR-HN516P16-3T, AVR-HN516P16-4T, AVR-HN516P16-6T, AVR-HN516P16-8T, AVR-HN516P16, AVR-HN516P16A, AVR-HN516P16C-10T, AVR-HN516P16C-12T, AVR-HN516P16C-16T, AVR-HN516P16C-1T, AVR-HN516P16C-20T, AVR-HN516P16C-24T, AVR-HN516P16C-2T, AVR-HN516P16C-30T, AVR-HN516P16C-32T, AVR-HN516P16C-3T, AVR-HN516P16C-40T, AVR-HN516P16C-48T, AVR-HN516P16C-4T, AVR-HN516P16C-6T, AVR-HN516P16C-8T, AVR-HN516P16C-FD-10T, AVR-HN516P16C-FD-12T, AVR-HN516P16C-FD-16T, AVR-HN516P16C-FD-1T, AVR-HN516P16C-FD-20T, AVR-HN516P16C-FD-24T, AVR-HN516P16C-FD-2T, AVR-HN516P16C-FD-30T, AVR-HN516P16C-FD-32T, AVR-HN516P16C-FD-3T, AVR-HN516P16C-FD-40T, AVR-HN516P16C-FD-48T, AVR-HN516P16C-FD-4T, AVR-HN516P16C-FD-6T, AVR-HN516P16C-FD-8T, AVR-HN516P16C-FD, AVR-HN532E2N-FD-10T, AVR-HN532E2N-FD-12T, AVR-HN532E2N-FD-16T, AVR-HN532E2N-FD-1T, AVR-HN532E2N-FD-20T, AVR-HN532E2N-FD-24T, AVR-HN532E2N-FD-28T, AVR-HN532E2N-FD-2T, AVR-HN532E2N-FD-30T, AVR-HN532E2N-FD-32T, AVR-HN532E2N-FD-36T, AVR-HN532E2N-FD-3T, AVR-HN532E2N-FD-40T, AVR-HN532E2N-FD-42T, AVR-HN532E2N-FD-48T, AVR-HN532E2N-FD-4T, AVR-HN532E2N-FD-56T, AVR-HN532E2N-FD-60T, AVR-HN532E2N-FD-64T, AVR-HN532E2N-FD-6T, AVR-HN532E2N-FD-70T, AVR-HN532E2N-FD-80T, AVR-HN532E2N-FD-8T, AVR-HN532E2N-FD-96T, AVR-HN532E2N-FD, AVR-HN532P16-56T, AVR-HN532P16-64T, AVR-HN532P16-FD-10T, AVR-HN532P16-FD-12T, AVR-HN532P16-FD-16T, AVR-HN532P16-FD-1T, AVR-HN532P16-FD-20T, AVR-HN532P16-FD-24T, AVR-HN532P16-FD-2T, AVR-HN532P16-FD-30T, AVR-HN532P16-FD-32T, AVR-HN532P16-FD-36T, AVR-HN532P16-FD-3T, AVR-HN532P16-FD-40T, AVR-HN532P16-FD-48T, AVR-HN532P16-FD-4T, AVR-HN532P16-FD-56T, AVR-HN532P16-FD-60T, AVR-HN532P16-FD-64T, AVR-HN532P16-FD-6T, AVR-HN532P16-FD-70T, AVR-HN532P16-FD-80T, AVR-HN532P16-FD-8T, AVR-HN532P16-FD-96T, AVR-HN532P16-FD User Manual

USER’S MANUAL

NETWORK VIDEO RECORDER

*Please read this manaul carefully for correct use of the product and preserve it for reference purposes

Notes

 Please read this user manual carefully to ensure that you can use the device correctly and

safely.

 There may be several technically incorrect places or printing errors in this manual. The

updates will be added into the new version of this manual. The contents of this manual are subject to change without notice.

 This device should be operated only from the type of power source indicated on the

marking label. The voltage of the power must be verified before using the same. Kindly remove the cables from the power source if the device is not to be used for a long period of time.

 Do not install this device near any heat sources such as radiators, heat registers, stoves or

other devices that produce heat.

 Do not install this device near water. Clean only with a dry cloth.  Do not block any ventilation openings and ensure proper ventilation around the machine.  Do not power off the device at normal recording condition.  This machine is for indoor use only. Do not expose the machine in rain or moist

environment. In case any solid or liquid get inside the machine’s case, please turn off the

device immediately and get it checked by a qualified technician.

 Do not try to repair the device by yourself without technical aid or approval.  When this product is in use, the relevant contents of Microsoft, Apple and Google will be

involved in. The pictures and screenshots in this manual are only used to explain the usage of our product. The ownerships of trademarks, logos and other intellectual properties related to Microsoft, Apple and Google shall belong to the above-mentioned companies.

 This manual is suitable for many models. All examples and pictures used in the manual are

from one of the models for reference purpose.

NVR User Manual

Contents

Contents .................................................................................................................................................................. i

1 Introduction ............................................................................................................................................. 1

1.1 Summary .................................................................................................................................................. 1

1.2 Features .................................................................................................................................................... 1

1.3 Front Panel Descriptions .......................................................................................................................... 4

1.4 Rear Panel Descriptions ........................................................................................................................... 5

1.5 Connections .............................................................................................................................................. 8

2 Basic Operation Guide .......................................................................................................................... 11

2.1 Startup & Shutdown ............................................................................................................................... 11

2.1.1 Startup ........................................................................................................................................ 11

2.1.2 Shutdown ................................................................................................................................... 11

2.2 Remote Controller .................................................................................................................................. 11

2.3 Mouse Control ........................................................................................................................................ 13

2.4 Text-input Instruction ............................................................................................................................. 13

2.5 Common Button Operation .................................................................................................................... 14

3 Wizard & Main Interface...................................................................................................................... 15

3.1 Startup Wizard ........................................................................................................................................ 15

3.2 Main Interface ........................................................................................................................................ 23

3.2.1 Main Interface Introduction ....................................................................................................... 23

3.2.2 Setup Panel ................................................................................................................................ 24

3.2.3 Main Functions .......................................................................................................................... 26

4 Camera Management ............................................................................................................................ 28

4.1 Add/Edit Camera .................................................................................................................................... 28

4.1.1 Add Camera ............................................................................................................................... 28

4.1.2 Edit Camera ............................................................................................................................... 30

4.2 Add/Edit Camera Group ......................................................................................................................... 31

4.2.1 Add Camera Group .................................................................................................................... 31

4.2.2 Edit Camera Group .................................................................................................................... 32

4.2.3 IP Planning ................................................................................................................................. 32

5 Live Preview Introduction .................................................................................................................... 34

5.1 Preview Interface Introduction ............................................................................................................... 34

5.2 Preview Mode ........................................................................................................................................ 35

5.2.1 Preview By Display Mode ......................................................................................................... 35

5.2.2 Quick Sequence View ................................................................................................................ 37

5.2.3 Camera Group View In Sequence .............................................................................................. 38

5.2.4 Scheme View In Sequence ......................................................................................................... 38

5.3 POS Settings .......................................................................................................................................... 40

5.4 Preview Image Configuration ................................................................................................................. 41

5.4.1 OSD Settings ............................................................................................................................. 41

5.4.2 Image Settings............................................................................................................................ 42

5.4.3 Mask Settings ............................................................................................................................. 42

5.4.4 Image Adjustment ...................................................................................................................... 43

6 PTZ ......................................................................................................................................................... 46

6.1 PTZ Control Interface Introduction ........................................................................................................ 46

6.2 Preset Setting .......................................................................................................................................... 49

6.3 Cruise Setting ......................................................................................................................................... 50

7 Record & Disk Management ................................................................................................................ 52

7.1 Record Configuration ............................................................................................................................. 52

7.1.1 Mode Configuration ................................................................................................................... 52

Contents

NVR User Manual

7.1.2 Advanced Configuration ............................................................................................................ 54

7.2 Encode Parameters Setting ..................................................................................................................... 54

7.3 Schedule Setting ..................................................................................................................................... 55

7.3.1 Add Schedule ............................................................................................................................. 55

7.3.2 Record Schedule Configuration ................................................................................................. 57

7.4 Record Mode .......................................................................................................................................... 58

7.4.1 Manual Recording ...................................................................................................................... 58

7.4.2 Timing Recording ...................................................................................................................... 58

7.4.3 Motion Based Recording ............................................................................................................ 58

7.4.4 Sensor Based Recording ............................................................................................................ 58

7.4.5 Intelligence Recording ............................................................................................................... 59

7.5 Disk Management .................................................................................................................................. 59

7.5.1 Storage Mode Configuration ...................................................................................................... 59

7.5.2 View Disk and S.M.A.R.T. Information ..................................................................................... 60

8 Playback & Backup ............................................................................................................................... 62

8.1 Instant Playback ..................................................................................................................................... 62

8.2 Playback Interface Introduction .............................................................................................................. 62

8.3 Record Search, Playback & Backup ....................................................................................................... 65

8.3.1 Search, Playback & Backup by Time-sliced Image .................................................................... 65

8.3.2 Search, Playback & Backup by Time ......................................................................................... 67

8.3.3 Search, Playback & Backup by Event ........................................................................................ 67

8.3.4 Search & Playback by Tag ......................................................................................................... 68

8.3.5 Image Management .................................................................................................................... 69

8.3.6 View Backup Status ................................................................................................................... 69

9 Alarm Management ............................................................................................................................... 70

9.1 Sensor Alarm ................................................................................................................................ .......... 70

9.2 Motion Alarm ......................................................................................................................................... 71

9.2.1 Motion Configuration ................................................................................................................ 71

9.2.2 Motion Alarm Handling Configuration ...................................................................................... 72

9.3 Intelligence Alarm .................................................................................................................................. 72

9.3.1 Object Detection ........................................................................................................................ 72

9.3.2 Exception ................................................................................................................................... 74

9.3.3 Tripwire ..................................................................................................................................... 75

9.3.4 Intrusion Detection ..................................................................................................................... 76

9.4 Exception Alarm ..................................................................................................................................... 78

9.4.1 IPC Offline Settings ................................................................................................................... 78

9.4.2 Exception Handling Settings ...................................................................................................... 78

9.5 Alarm Event Notification ....................................................................................................................... 79

9.5.1 Alarm-out ................................ ................................................................ ................................ ... 79

9.5.2 E-mail ........................................................................................................................................ 79

9.5.3 Display ....................................................................................................................................... 79

9.5.4 Buzzer ........................................................................................................................................ 80

9.5.5 Push Message ............................................................................................................................. 80

9.6 Manual Alarm ........................................................................................................................................ 80

9.7 View Alarm Status .................................................................................................................................. 81

10 Account & Permission Management .................................................................................................... 82

10.1 Account Management ........................................................................................................................... 82

10.1.1 Add User .................................................................................................................................. 82

10.1.2 Edit User .................................................................................................................................. 83

10.2 User Login & Logout ........................................................................................................................... 85

10.3 Permission Management ...................................................................................................................... 85

10.3.1 Add Permission Group ............................................................................................................. 85

10.3.2 Edit Permission Group ............................................................................................................. 86

10.4 Black and White List ............................................................................................................................ 86

10.5 Preview On Logout .............................................................................................................................. 87

10.6 View Online User ................................................................................................................................. 87

Contents

NVR User Manual

iii

11 Device Management .............................................................................................................................. 88

11.1 Network Configuration ......................................................................................................................... 88

11.1.1 TCP/IP Configuration ............................................................................................................... 88

11.1.2 Port Configuration .................................................................................................................... 91

11.1.3 PPPoE Configuration ............................................................................................................... 92

11.1.4 DDNS Configuration................................................................................................................ 92

11.1.5 E-mail Configuration................................................................................................................ 95

11.1.6 UPnP Configuration ................................................................................................................. 96

11.1.7 NAT Configuration ................................................................................................................... 97

11.1.8 FTP Configuration .................................................................................................................... 97

11.1.9 View Network Status ................................................................................................................ 97

11.2 Basic Configuration .............................................................................................................................. 98

11.2.1 Common Configuration ............................................................................................................ 98

11.2.2 Date and Time Configuration ................................................................................................... 99

11.3 Factory Default ................................................................................................................................... 100

11.4 Device Software Upgrade ................................................................................................................... 100

11.5 Backup and Restore ............................................................................................................................ 100

11.6 Restart Automatically ......................................................................................................................... 101

11.7 View Log ............................................................................................................................................ 101

11.8 View System Information ................................................................................................................... 102

12 Remote Surveillance ............................................................................................................................ 103

12.1 Mobile Client Surveillance ................................................................................................................. 103

12.2 Web LAN Access ............................................................................................................................... 103

12.3 Web WAN Access ............................................................................................................................... 104

12.4 Web Remote Control .......................................................................................................................... 105

12.4.1 Remote Preview ..................................................................................................................... 106

12.4.2 Remote Playback ................................................................................................................... 109

12.4.3 Remote Backup ...................................................................................................................... 110

12.4.4 Remote Configuration ............................................................................................................ 110

Appendix A FAQ .............................................................................................................................................. 111

Appendix B Calculate Recording Capacity ................................................................................................... 117

Appendix C Compatible Device List .............................................................................................................. 118

Introduction

NVR User Manual

1.1 Summary

Based on the most advanced SOC technology and embedded system in the field, this series of the NVR adopt the new designed human interface and support the smart management of the IP camera and the record search of slice. This series of the NVR which are powerful and easy to use are provided with excellent image quality and stable system. They are centralized monitoring management products with high performance and high quality specially designed for network video monitoring field. This series of the NVR can be widely used to security system of banks at home and abroad, schools, intelligent mansions, traffic, environmental protection, supermarkets, petrol service stations, residential quarters and factories and so on.

1.2 Features

Basic Functions

 Support network device access including IP camera/dome and the third party IP cameras  Some NVRs support the latest H.265 video coding stream and a mixture input of H.265

and H.264 IP cameras

 Support standard ONVIF protocol  Support dual stream recording of each camera  Support IP cameras to be added quickly or manually  Support batch or single configuration of the cameras’ OSD, video parameters, mask,

motion and so on  Support a maximum of 8 user permission groups including Administrator, Advanced and Ordinary which are the default permission groups of the system  Support a maximum of 16 users to be created, multiple web clients login by using one username at the same time and the user’s permission control to be enabled or disabled  Support a maximum of 10 web clients login at the same time

Live Preview

 Support 4K×2K/1920×1080/1280×1024 HDMI and 1920×1080/1280×1024 VGA high definition synchronous display

 Support multi-screen modes such as 1/4/6/8/9/13/16/25/36  Support auto adjustment of the camera’s image display proportion  Support audio monitoring of the camera to be enabled or disabled  Support manual snap of the preview camera  Support the sequence of the preview cameras to be adjusted  Support display mode to be added and saved and the saved modes can be called directly  Support quick tool bar operation of the preview window  Support camera group view and scheme view in sequence, quick sequence view and dwell

time setting

 Support motion detection and video mask  Support multiple popular P.T.Z. control protocol and setup of the preset and cruise

1 Introduction

Introduction

NVR User Manual

 Support direct mouse control of the IP dome including rotating, zoom, focusing and so on  Support single camera image to be zoomed by sliding the scroll wheel of the mouse  Support any area of the image to be zoomed in to a maximum of 16 times of the current

size

 Support image and lens adjustment (only available for some cameras)  Support quick camera adding in the camera window of the live preview interface  The live camera sequence of the web client will keep consistent with that of the NVR after

adjusting the live camera sequence of the NVR, but the live camera sequence of the NVR will not be changed if that of the web client is changed

 The NVRs with the 3U case can add a maximum of 16 SATA HDDs; a maximum of 8 SATA HDDs with the 2U case, a maximum of 4 SATA HDDs with the 1.5U case, a maximum of 2 SATA HDDs with the 1U case and a maximum of 1 SATA HDD with the small 1U case

 Each SATA interface of the NVR supports the HDDs with max 8TB storage capacity  Some of the NVRs support record to be backed up by e-SATA HDD  Support disk group configuration and management and each camera can be added into

different disk groups with different storage capacity

 Support disk information and disk working status viewing  Support batch formatting of the disks

 Support main stream and sub stream recording at the same time and batch or single

configuration of the record stream

 Support manual and auto record modes  Support schedule recording, sensor alarm recording and motion detection recording, etc  Support schedule recording and event recording setting with different record streams  Support record schedule setting and recycle recording  Support pre recording and delay recording configuration of the event recording

 Support time scale operation in quick playback and the playback date and time can be set

randomly by scrolling the mouse; the time interval of the time scale can be zoomed

 Support record searching by time slice/time/event/tag  Support time view and camera view in searching by time slice mode  Support time slice searching by month, by day, by hour and by minute and time slice to be

displayed with camera thumbnail

 Support a maximum of 16 cameras to be searched by time  Support event searching by manual/motion/sensor/intelligent events  Support tag searching by the manual added tags  Support instant playback of the selected camera in the live preview interface  Support a maximum of 16 synchronous playback cameras  Support acceleration(maximum 32 times of the normal speed), deceleration (minimum

1/32 times of the normal speed) and 30s’ addition or reduction to current playing time

Disk Management

Record Configuration

Record Playback

Record Backup

Introduction

NVR User Manual

 Support record to be backed up through USB (U disk, mobile HDD) or e-SATA interface  Support record to be backed up by time/event/image searching  Support record cutting for backing up when playing back  Support a maximum of 10 backup tasks in background and backup status viewing

Alarm Management

 Support alarm schedule setting  Support enabling or disabling of the motion detection, external sensor alarm input,

intelligence alarm and exception alarms including IP address conflict alarm, disk IO error alarm, disk full alarm, no disk alarm, illegal access alarm, network disconnection alarm, IPC offline alarm and so on, alarm trigger configuration supportable

 Support IPC offline alarm trigger configuration of PTZ, snap, pop-up video, etc.  Support event notification modes of alarm-out, pop-up video, pop-up message box, buzzer,

e-mail and so on

 The snapped images can be attached into the e-mail when alarm linkage is triggered  Support alarm status view of alarm-in, alarm-out, motion detection and exception alarm  Support alarm to be triggered and cleared manually  Support system auto reboot when exception happens

Network Functions

 Support TCP/IP and PPPoE, DHCP, DNS, DDNS, UPnP, NTP, SMTP protocol and so on  Support allow and block list function and the allow and block IP address/IP segment/MAC

address can be set  Support multiple browsers including IE8/9/10/11, Firefox, Opera, Chrome (available only for the versions lower than 45) and Safari in MAC system  Support remote achievement, configuration, import and export of the NVR parameters and other system maintenance operations including remote upgrading and system restart  Support remote camera configuration of the NVR including video parameters, image quality and so on

 Support remote searching, playback and backup of the NVR  Support manual alarm to be triggered and cleared remotely  The auto-focusing camera can be adjusted through web client (support zoom in/out, but

one key focus is not currently supported)

 Support NVMS or other platform management software to access the NVR and manage it  Support NAT function and QRCode scanning by mobile phone and PAD  Support mobile surveillance by phones or PADs with iOS or Android OS  Support NVR to be accessed remotely through telnet and the telnet function can be

enabled or disabled  If one camera recording is enabled or disabled manually through web client, it will be simultaneously enabled or disabled in the NVR

Other Functions

 The NVR can be controlled and operated by the buttons on the front panel, the remote controller and the mouse  Setting interfaces can be switched to one another conveniently by clicking the main menus

Introduction

NVR User Manual

Name

Descriptions

REC

When recording, the light is blue

Net

When access to network , the light is blue

Power

Power indicator, when connection , the light is blue

No function temporarily

Name

Descriptions

Power

Power Indicator, when connected, the light is blue

HDD

The light turns blue when reading/writing HDD

Net

The light turns blue when it is able to access the network

Backup

The light turns blue when backing up files and data

Play

The light turns blue when playing video

REC

Power Indicator, when connected, the light is blue

AUDIO /+

1. Adjust audio 2. Increase the value in setup

P.T.Z / -

1. Enter PTZ mode 2. Decrease the value in setup

Enter Menu in live

INFO

Check the information of the device

BACKUP

Enter backup mode in live

Enter search mode in live

Exit

Exit the current interface

Manually record

Play/Pause

Speed down

Speed up

on the top of the setting interfaces  Support NVR information viewing including basic, camera status, alarm status, record status, network status, disk and backup status  Support factory restoring, import and export of the system configuration, log view and export and local upgrading by USB mobile device

 Support auto recognition of the displayer’s resolution  You can click the right mouse button at any interface to go back to the upper interface  You can click the middle mouse button at any interface to go to the live view interface  The display language and video format of the NVR will not be changed and the system

logs will be reserved if you reset the NVR to factory default  Press and hold the right mouse button for 5 seconds in any interface to switch the output to VGA and the NVR will display the video at the lowest resolution which the NVR supports

1.3 Front Panel Descriptions

The following descriptions are for reference only. Type I:

Type II:

Introduction

NVR User Manual

Name

Descriptions

1-9

Input digital number and select camera

0/--

Input number 0, the number above 10

Direction Key

Change direction

Multi-Screen Switch

Change the screen mode

Enter

Confirm selection

USB

To connect external USB device like USB mouse or USB flash

No.

Name

Descriptions

ALARM OUT

Relay output; connect to external alarm

GND

Grounding

AUDIO IN

Audio input; connect to audio input device, like microphone, pickup, etc

DC12V

DC12V power input

LAN

Network port

VGA

Connect to monitor

ALARM IN

Alarm inputs for connecting sensors

HDMI

Connect to high definition display device

USB

Connect USB storage device or USB mouse

AUDIO OUT

Audio output; connect to sound box

RS485

Connect to keyboard. A is TX+; B is TX-

1.4 Rear Panel Descriptions

Here we only take a part of real panels for example to introduce their interfaces and connections. The interfaces and locations of the interfaces are only for references. Please take the real object as the standard.

Introduction

NVR User Manual

No.

Name

Descriptions

VGA

Connect to monitor

e-SATA

Connect to HDD with e-SATA interface

RS485 Y/Z interface

Unavailable right now

RS485 A/B interface

Connect to keyboard. A is TX+; B is TX-

AUDIO OUT

Audio output; connect to sound box

LAN

Network port

HDMI

Connect to high definition display device

USB

Connect USB storage device or USB mouse

GND

Grounding

ALARM OUT

Relay output; connect to external alarm

ALARM IN

Alarm inputs for connecting sensors

AUDIO IN

Audio input; connect to audio input device, like microphone, pickup, etc

Power Switch

Press the switch to turn on/off the NVR

Power Supply

Power supply interface

Introduction

NVR User Manual

No.

Name

Descriptions

VGA

Connect to monitor

RS485 Y/Z interface

Unavailable right now

ALARM OUT

Relay output; connect to external alarm

GND

Grounding

AUDIO OUT

Audio output; connect to sound box

e-SATA1/ e-SATA2

Connect to HDD with e-SATA interface

LAN1/LAN2

Network port

HDMI1

Connect to 4K×2K high definition display device

USB3.0/USB

USB3.0 and USB 2.0 interface, connect USB storage device or USB mouse

HDMI2

Connect to 1920×1080 high definition display device

RS485 A/B interface

Connect to keyboard. A is TX+; B is TX-

ALARM IN

Alarm inputs for connecting sensors

AUDIO IN

Audio input; connect to audio input device, like microphone, pickup, etc

Power Switch

Press the switch to turn on/off the NVR

Power Supply

Power supply interface

No.

Name

Descriptions

Power Supply

DC48V power supply interface

PoE port

8 PoE network ports; connect to 8 PoE IP cameras

LAN

Network port

VGA

Connect to monitor

HDMI

Connect to 1920×1080 high definition display device

USB3.0

USB3.0 interface, connect USB storage device or USB mouse

AUDIO IN

Audio input; connect to audio input device, like microphone, pickup, etc

AUDIO OUT

Audio output; connect to sound box

Power Supply

DC12V power supply interface

Introduction

NVR User Manual

No.

Name

Descriptions

e-SATA

Connect to HDD with e-SATA interface

LAN1/LAN2

Network port

HDMI2

Connect to 1920×1080 high definition display device

USB

USB interface, connect USB storage device or USB mouse

HDMI1

Connect to 4K×2K high definition display device

VGA

Connect to monitor

RS485 Y/Z interface

Unavailable right now

RS485 A/B interface

Connect to keyboard. A is TX+; B is TX-

ALARM OUT

Relay output; connect to external alarm

GND

Grounding

ALARM IN

Alarm inputs for connecting sensors

AUDIO IN

Audio input; connect to audio input device, like microphone, pickup, etc

AUDIO OUT

Audio output; connect to sound box

Power Switch

Press the switch to turn on/off the NVR

Power Supply

Power supply interface

1.5 Connections

 Video Connections

Video Output: Supports VGA/HDMI video output. You can connect to monitor through these video output interfaces simultaneously or independently.

 Audio Connections

Audio Input: Connect to microphone, pickup, etc. Audio Output: Connect to headphone, sound box or other audio output devices.

 Alarm Connections

Introduction

NVR User Manual

Some models may support this function. Take 16 CH alarm inputs and 1 CH alarm output for example.

Alarm Input: Alarm IN 1~16 are 16 CH alarm input interfaces. There are no type requirements for sensors. NO type and NC type are both available. The way to connect sensor and the device is as shown below:

The alarm input is an open/closed relay. If the input is not an open/closed relay, please refer to the following connection diagram:

Alarm Output: The way to connect alarm output device: Pull out the green terminal blocks and loosen the screws in the alarm-out port. Then insert the signal wires of the alarm output devices into the port of NO and COM separately. Finally, tighten the screws. Provided that the external alarm output devices need power supply, you can connect the power supply as per the following figures.

Introduction

NVR User Manual

 RS485 Connection

There are two types of RS485 interfaces:

（Type 1）（Type 2）

Type 1: The P/Z interfaces are unavailable temporarily. K/B interfaces are used to connect keyboard. Type 2: The RS485 interfaces are used to connect keyboard. A is TX+; B is TX-.

Basic Operation Guide

NVR User Manual

2 Basic Operation Guide

2.1 Startup & Shutdown

Please make sure all the connections are done properly before you power on the unit. Proper startup and shutdown are crucial to expending the life of your device.

2.1.1 Startup

① Connect the output display device to the VGA/HDMI interface of the NVR. ② Connect with the mouse and power. The device will boot and the power LED would turn

blue. ③ A WIZARD window will pop up (you should select the display language the first time you use the NVR). Refer to 3.1 Startup Wizard for details.

2.1.2 Shutdown

You can power off the device by using remote controller or mouse.

By remote controller:

① Press Power button. This will take you to a shutdown window. The unit will power off after a while by clicking “OK” button. ② Disconnect the power.

By mouse:

① Click StartShutdown to pop up the Shutdown window. Select “Shutdown” in the window. The unit will power off after a while by clicking “OK” button. ② Disconnect the power.

2.2 Remote Controller

① It uses two AAA size batteries. ② Open the battery cover of the remote controller. ③ Place batteries. Please take care the polarity (+ and -). ④ Replace the battery cover.

Key points to check in case the remote doesn’t work.

1. Check batteries polarity.

2. Check the remaining charge in the batteries.

3. Check IR controller sensor for any masking.

If it still doesn’t work, please change a new remote controller to try, or contact your dealers. You can just turn the IR sensor of the remote controller towards the IR receiver of the NVR to control it when you are controlling multiple devices by remote controller. There are two kinds of remote controller. The interface of remote controller is shown as below.

Basic Operation Guide

NVR User Manual

Button

Function

Power Button

Switch off—to stop the device

Record Button

To start recording

-/-- /0-9

Input number or choose camera

Fn1 Button

Unavailable temporarily

Multi Button

To choose multi screen display mode

Next Button

To switch the live image

SEQ

To go to sequence view mode

Audio

To enable audio output in live mode

Switch

No function temporarily

Direction button

To move cursor in setup or pan/title PTZ

Enter Button

To confirm the choice or setup

Menu Button

To go to menu

Exit Button

To exit the current interface

Focus/IRIS/Zoom/PTZ

To control PTZ camera

Preset Button

To enter into preset setting in PTZ mode

Cruise Button

To go to cruise setting in PTZ mode

Track Button

No track function temporarily

Wiper Button

No function temporarily

Light Button

No function temporarily

Clear Button

No function temporarily

Fn2 Button

No function temporarily

Info Button

Get information about the device

To control playback. Play(Pause)/Stop/Previous Frame/Next Frame/Speed Down/Speed Up

Snap Button

To take snapshots manually

Search Button

To go to search mode

Cut Button

No function temporarily

Backup Button

To go to backup mode

Zoom Button

To zoom in the images

PIP Button

No function temporarily

Note: You shall press P.T.Z button to enter PTZ setting mode, choose a channel and press P.T.Z button again to hide the P.T.Z control panel. Then you can press preset, cruise, track, wiper or light button to enable the relevant function.

Basic Operation Guide

NVR User Manual

Button

Function

REC

Record manually

To enter search mode

MEUN

To enter menu

Exit

To exit the current interface

ENTER

To confirm the choice or setup

Direction button

To move cursor in setup

ZOOM

To zoom in

PIP

No function temporarily

To control playback. Play(Pause)/Next Frame/Speed Up/Stop/Previous Frame/Speed Down

Multi

To choose multi screen display mode

To switch the live image

SEQ

To go to sequence view mode

INFO

Get information about the device

Note: Mouse is the default tool for all operations unless an exception as indicated.

2.3 Mouse Control

 Mouse control in Live Display & Playback interface

In the live display & playback interface, double click on any camera window to show the window in single screen mode; double click the window again to restore it to the previous size.

In the live display & playback interface, if the interfaces display in full screen, move the mouse to the bottom of the interface to pop up a tool bar. The tool bar will disappear automatically after you move the mouse away from it for some time; move the mouse to the right side of the interface to pop up a panel and the panel will disappear automatically after you move the mouse away from it.

 Mouse control in text-input

Move the mouse to the text-input box and then click the box. The input keyboard will pop up automatically.

2.4 Text-input Instruction

Basic Operation Guide

NVR User Manual

Button

Meaning

Button

Meaning

Backspace key

Switch key of punctuation character

Delete Key

Enter key

Switch key between upper and lower letter

Space key

Switch key of language

Button

Meaning

Click it to show the menu list.

Click it to change the sequence of the list.

Click it to change the camera displaying mode.

Click it to close the current interface.

Click it to go to the earliest date of camera recording.

Click it to go to the latest date of camera recording.

The system includes two input boxes. Refer to the above pictures. The left box is the number input box and the right box is the input box which provides inputs of numbers, letters and punctuation characters. The introductions of keys on the input boxes are shown below.

2.5 Common Button Operation

Wizard & Main Interface

NVR User Manual

3 Wizard & Main Interface

3.1 Startup Wizard

The disk icons will be shown on the top of the startup interface. You can view the number and status of each disk quickly and conveniently through these icons ( : no disk; : unavailable disk; : RW available disk).

You can quickly configure the NVR by wizard setup to make the NVR work normally. You must configure the wizard if you start the NVR for the first time (or click “Skip” to cancel the wizard next time).

Click “Wizard Setup” to start wizard. The setting steps are as follows. ① System Login. Set your own password or use the default when you use the wizard for the first time (the default username of the system is admin and the default password of admin is

123456); select the login username and enter the corresponding password next time.

Click “Edit Security Question” to set questions and answers for password security of admin. If you forget the password, please refer to Q4 in Appendix A FAQ for details. Click “Next” to continue or click “Cancel” to exit the wizard.

Wizard & Main Interface

NVR User Manual

② Date and Time Configuration. The date and time of the system need to be set up if you use the wizard for the first time. Refer to the following figure. Set the time zone, system time, date format and time format. The DST will be enabled by default if the time zone selected

includes DST. Click “Next” to continue.

③ Network Settings. Check “Obtain an IP address automatically” and “Obtain DNS automatically” to get the IP address and DNS automatically (the DHCP function of the router in the same LAN should also be enabled), or manually input them. Input the HTTP port, RTSP port and Server port (please see 11.1.2 Port Configuration for details). Click “Next” to continue.

Wizard & Main Interface

NVR User Manual

Note:

 If you use the NVR with the PoE network ports, the online state of the internal ethernet port will be shown on the interface. Refer to the picture below. Please refer to 11.1.1 TCP/IP Configuration for detail introduction of the internal ethernet port.

Wizard & Main Interface

NVR User Manual

 If the NVR has two network ports or above, you can select the network work pattern as required. Network Fault Tolerance and Multiple Address Setting are available. Refer to the pictures below. Please refer to 11.1.1 TCP/IP Configuration for more detailed information.

Wizard & Main Interface

NVR User Manual

Wizard & Main Interface

NVR User Manual

④ Add Camera. Click “Refresh” to refresh the list of online IP cameras which are in the same local network with NVR and then click to add the searched camera. Click “Add All” to add all the cameras in the list. Click to delete the added camera. Click “Delete

All” to delete all the added cameras.

Wizard & Main Interface

NVR User Manual

Click to edit the searched IP camera as shown on the below left. Input the new IP address, subnet mask, gateway, username and the password of the camera. You can check “Sync to IPC” to modify the IP address of the IPC via different network segments for being in the same network segment with the NVR. Click “OK” to save the settings.

Click to edit the added camera as shown on the above right. Input the new camera name, IP address, port, username and the password of the camera. You can click “Test” to test the effectiveness of the input information. Click “OK” to save the settings. You can change the IP camera name only when the added camera is online. Click “Next” to continue.

⑤ Disk Settings. You can view the disk number, disk capacity of the NVR and serial number, R&W status of the disk. Click “Formatting” to format the disk. Click “Next” to continue.

Wizard & Main Interface

NVR User Manual

⑥ Record Settings. Two record modes are available: auto and manual. Auto: Select one auto mode in the interface as shown below and then click “Next” button to

save the settings. Click “Advanced” to self-define record mode. See 7.1.1 Mode Configuration for details.

Manual: Set the “Sensor Record”, “Motion Record” and “Schedule Record” of each camera. Click “OK” to save the settings. See 7.1.1 Mode Configuration for details.

⑦ QRCode. Enable the NAT function in the interface or set it in the network configuration after exiting the wizard (please refer to 11.1.7 NAT Configuration for details). You can scan the QRCode through mobile client which is installed in the mobile phone or PAD to log in the

mobile client instantly. Please refer to 12.1 Mobile Client Surveillance for details. Click“OK” to save the settings.

Wizard & Main Interface

NVR User Manual

3.2 Main Interface

Button

Meaning

Start button. Click it to pop up area ③.

Full screen button. Click it to show full screen; click it again to exit the full screen.

Screen mode button.

Dwell button (see 5.2.2 Quick Sequence View and 5.2.4 Scheme View In Sequence for details).

Click it to enable OSD; click to disable OSD.

Click to set the default playback time before starting instant playback (8.1 Instant Playback) or going to the playback interface for playback operations

(8.2 Playback Interface Introduction); click to go to the playback interface. For instance, if you choose “5 minutes ago” as the default playback time, you can playback the record from the past five minutes.

Manual record button. Click it to enable/disable record.

Manual alarm button. Click it to trigger or clear the alarm-out manually in the popup window.

Record status button. Click it to view the record status.

Alarm status button. Click it to view the alarm status.

3.2.1 Main Interface Introduction

The buttons in area ① are introduced in the table below.

Wizard & Main Interface

NVR User Manual

Button

Meaning

Disk status button. Click it to view the disk status and RAID status.

Network status button. Click it to view the network status.

Information button. Click it to view system information.

Icon / Button

Meaning

It shows the current login user.

Click it to go to record search and backup interface, see 8.3 Record Search, Playback & Backup for details.

Click it to go to playback interface (click on the tool bar at the bottom of the live preview interface to set the default playback time), see 8.2 Playback Interface Introduction for details.

Click it to pop up the setup panel, see 3.2.2 Setup Panel for details.

Click it to log out the system.

Click it and then select “Logout”, “Reboot” or “Shutdown” in the popup window.

Introduction of area ②: Click “Camera” to view all the added cameras in the camera list. Select one camera window on the left side of the interface and then double click one camera in the list to preview the camera image in the selected window. Click “Single Channel Sequences” to view all the added groups in the group list; click one group in the list to view all the added cameras in the group (refer to 4.2 Add/Edit Camera Group for detail configuration of the camera group). Select one camera window on the left side of the interface and then double click one group in the group list to preview the cameras’ images one by one in the selected window. Click “Customize Display Modes” to view all the display modes in the display mode list (refer to 5.2.1 Preview By Display Mode for detail configuration of the display mode). Double click one display mode in the list to switch to the display mode for previewing.

Introduction of area ③:

3.2.2 Setup Panel

Click StartSettings to pop up the setup panel as shown below.

Wizard & Main Interface

NVR User Manual

The setup panel includes seven modules. Each module provides some function entries with links for convenient operation. Here we take Camera module as an example. The Camera module provides convenient links such as “Add Camera”, “Edit Camera”, “Image Settings”, “Motion”, “Intelligence Analysis” and “PTZ”. Click Camera to go to the camera management interface as shown below.

There are some function items on the left side of the camera management interface. Click each item to go to corresponding interface or window. For instance, click “Add Camera” to pop up the window as shown below.

+ 94 hidden pages